The syntheses of fluorinated alkanesulfonamides and poly-(fluorinated alkanesulfonamides)

In order to synthesize poly-(fluorinated alkanesulfonamides) a series of model experiments were carried out: (1) reactions of fluorinated alkanesulfonyl fluorides with amines, (2) reactions of fluorinated alkanesulfonyl chloride with amines and (3) reactions of sodium salts of fluorinated alkanesulfonamides with alkyl iodides of fluorinated alkanesulfonic acid esters. Seventeen new fluorinated alkanesulfonamides were prepared in good yields, namely: R_FO(CF₂)₂SO₂NR¹R² (1a-h), R¹R²NSO₂R_FSO₂NR¹R² (2a-h) and [Cl (CF₂)₄O(CF₂)₂SO₂NH(CH₂)₃]₂ (3). Reaction of R_FSO₂NH₂ with equivalent amount of NaOCH₃ and methyl iodide was shown to give both the N-mono- and N,N-di-substituted amides. Consequently the N-monosubstituted alkanesulfonamides were chosen as monomers for syntheses of the poly-(fluorinated alkanesulfonamides) and two new polymers were synthesized. The effect of the condition of the polycondensation on M?_n of the polymers were discussed and elemental composition, ¹⁹F NMR, IR, M?_n, Tg, tensile strength, thermal and chemical stabilities of the polymers were measured. Several new perfluoroalkanesulfonyl chlorides CISO₂R_FSO₂Cl (4a-c) and fluorinated alkanesulfonic acid esters (6a-d) were synthesized. However, reaction of CFCl₂CF₂O(CF₂)₂SO₂F with AlCl₃ was found to give Cl₃CCF₂O(CF₂)₂SO₂F (5) instead of the expected sulfonyl chloride.     

Some approaches to the synthesis of fluorinated alcohols and esters. II. Use of F-alkyl iodides for the synthesis of F-alkyl alkanols

Free radical addition of an F-alkyl iodide (R_FI) to an alkenol or ester, followed by appropriate reduction is an efficient method for preparing the corresponding F-alkyl-alkanols of the homologous series, R_F(CH₂)_n?OH. When n = 2,4 or higher, the two steps take place smoothly. The 1,2,3-substituted systems R_FCH₂CHYCH₂Z, however, are susceptible to surprising difficulties. Reduction of R_FCH₂CHICH₂ON to R_F(CH₂)₃OH by hydrogen and catalyst (strong base acid acceptor), can be done either in one step or $\text{via}$ R_FCHCHCH₂OH; however, dehydrohalogenation may also give the epoxide, and reduction in this case leads to the secondary alcohol, R_FCH₂CH(CH₃)OH. By contrast, reduction of R_FCH₂CHICH₂OAc by tributyltin hydride or with hydrogen over palladium (diethylamine acid acceptor) goes smoothly. Zinc and acid reduction of R_FCH₂CHICH₂OAc gives elimination to R_FCH₂CHCH₂; even R_FCHCICH₂OH gives R_FCHCCH₂ besides R_FCHCHCH₂OH. R_FCHCICH₂CH₂OH, however, with zinc and acid is reduced cleanly to R_FCHCHCH₂CH₂OH.     

Some approaches to the synthesis of fluorinated alcohols and esters. III. Synthesis of 2-(F-alkyl)ethanols from 2-(F-alkyl)-1-iodoethanes and amides.

1-Iodo-2-(F-alkyl)ethanes, R_FCH₂CH₂I, when heated with a large excess of N-methylformamide (NMF) give in high yield, mixtures of predominately R_FCH₂CH₂OH, some formate ester and a little R_FCHCH₂. In a study of this process, significant variables were examined, including solvent, reactant ratio, effect of water, and alternative amide reactants. The coproduct from NMF is the amidine salt, [MeNHCH(NHMe)]⁺I⁻. By contrast, R_FCH₂CH₂I with N,N-dimethylformamide (DMF) and water (one or two mols) gives chiefly the formate ester; the coproduct is Me₂NH₂⁺I⁻. A mechanistic scheme is proposed: in the first step, an alkyl imidate salt, e.g., [HC(NH Me)OCH₂CH₂R_F]⁺I⁻ is formed by O-alkylation of NMF; reaction of the imidate with more NMF gives a tetrahedral intermediate that breaks down rapidly to R_FCH₂CH₂OH, and HC(NHMe)NMeCHO⁺I⁻. The formate ester is derived from the alcohol and this N-formyl acylating agent, in a subsequent step. Analogously, the alkyl imidate salt from DMF and R_FCH₂CH₂I reacts with water as nucleophile (but not with DMF) to give a tetrahedral intermediate that cleaves under stereoelectronic control to formate ester and amine salt, but not to alcohol. Quantitative isolation of amine salt and amidine salt, and observed rates of reaction give solid support to this proposed mechanism.     

Some approaches to the synthesis of fluorine-containing alcohols and esters

Among F-containing alcohols only trifluoroethanol, the so-called ‘telomer alcohols’ [H(CF₂CF₂)_nCH₂OH], and certain esters of 2-(F-alkyl)ethanols and 3-(F-alkyl)propanols, have achieved commercial importance. Their utilization has been limited by lack of suitable methods of synthesis and by their high cost. Yet F-containing alcohols and their esters have unique properties, and comprise a versatile class of compounds. It is to be noted that completely fluorinated esters have recently become available.F-substituted alcohols must be made by special, less well-known methods. Routes based on tetrafluoroethylene (TFE) as starting material are of current interest. F-alkyl iodides (R_FI) are made in two steps from TFE. Reaction of R_FI with ethylene gives 2-(F-alkyl)-1-ethanes, and under suitable conditions, higher telomers in high yield. Displacement of iodine of R_FCH₂CH₂I by an acyloxy group gives an ester, such as acrylate or fumarate of the F-substituted alcohol. Several methods have been discovered for this process, most recently by reaction with N-methylformamide or N,N-dimethylformamide and water. Free radical addition of R_FI to vinyl acetate and subsequent reduction provided 2-(F-alkyl)ethanols in excellent yield. Similar steps using allyl acetate gave both 3-(F-alkyl)-1-propanols and 3-(F-alkyl)-2-propanols; the latter compound also was formed by hydrolysis of the initial adduct. These various methods will be outlined and some recent results in a study of O-alkylation will be presented.Support by the Central Research Group, Ciba-Geigy Corp., Ardsley, N.Y. is gratefully acknowledged.     

Perfluoro Alkyl Hypofluorites and Peroxides Revisited

A more convenient synthesis of the perfluoro alkyl hypofluorite (F₃C)₃COF as well as the hitherto unknown (C₂F₅)(F₃C)₂COF compound is reported. Both hypofluorites can be prepared by use of the corresponding tertiary alcohols R^FOH and elemental fluorine in the presence of CsF. An appropriate access to these highly reactive hypofluorites is crucial. The hypofluorites are then transferred into their corresponding perfluoro bisalkyl peroxides R^FOOR^F [R^F=(F₃C)₃C, (C₂F₅)(F₃C)₂C] by treatment with partially fluorinated silver wool. NMR, gas-phase infrared, and solid-state Raman spectra of the perfluoro bisalkyl peroxides are presented and their chemical properties are discussed.     

New fluorinated polysiloxanes containing an ester function in the spacer. I. Synthesis and characterization

Unsaturated perfluoroalkyl esters derived from undecylenic acid: CH₂?CH? (CH₂)₈? COO? CH₂? CH₂? R_F (with R_F?C₆F₁₃, 2a and R_F?C₈F₁₇, 2b ) and C₈F₁₇? (CH₂)₁₀? COO? CH₂? CH?CH₂, 2c were prepared with excellent yields. Their hydrosilylation by methylhydrodimethylsiloxane copolymers of various Si? H contents gives new fluorinated polysiloxanes which were examined by ¹H- and ¹³C-NMR, GPC, differential scanning calorimetry, and optical polarizing microscopy. Polymers derived from compounds 2a and 2b exhibit mesomorphic structures. © 1994 John Wiley & Sons, Inc.     

A fluoroalkyl end-capped <Emphasis Type="Italic">N</Emphasis>-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer/silica gel nanocomposite with no weight loss even at 800 °C equal to an original silica gel

Fluoroalkyl end-capped N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomer [R_F-(DOBAA)_n-R_F]/silica gel nanocomposite, which was prepared by reaction of the corresponding fluorinated oligomer with tetraethoxysilane and silica gel nanoparticles under alkaline conditions, exhibited no weight loss even at 800 °C equal to the original silica gel, although the corresponding parent R_F-(DOBAA)_n-R_F oligomer was completely degraded at 600 °C. Thermogravimetric analyses/mass spectra of fluorinated nanocomposite showed that this nanocomposite decomposed around 280 °C to afford CO₂ and H₂O as the major evolved gaseous products including some minor fluoro- and hydrocarbons. X-ray photoelectron spectroscopy analyses also showed that the contents of C, F, and Si atoms in R_F-(DOBAA)_n-R_F/SiO₂ nanocomposite after the calcination at 800 °C were similar to those before the calcination. These findings suggest that the evolved gaseous products should be encapsulated quantitatively into nanometer-size-controlled silica matrices to give the fluorinated silica gel nanocomposite with no weight loss even at 800 °C equal to the original silica gel.     

Preparation and properties of fluorinated carboxylic acid/silica nanocomposite-encapsulated low molecular weight compounds

Perfluoro-2-methyl-3-oxahexanoic acid/silica nanocomposites [R_F-CO₂H/SiO₂] were prepared by the sol–gel reaction of tetraethoxysilane in the presence of silica nanoparticles and the corresponding fluorinated carboxylic acid under alkaline conditions. R_F-CO₂H/SiO₂ nanocomposites were found to exhibit no weight loss in proportion to the contents of fluorinated carboxylic acid in the composites even after calcination at 800 °C. The modified glass surface treated with the R_F-CO₂H/SiO₂ nanocomposites was shown to give a good oleophobicity with superhydrophilicity imparted by fluorinated carboxylic acid in the composites. R_F-CO₂H/SiO₂ nanocomposites were also applied to the encapsulation of a variety of low molecular weight aromatic and aliphatic compounds such as bisphenol AF [BPAF], bisphenol A [BPA], 4,4′-biphenol [BPOH], octafluoro-4,4′-biphenol [FBPOH], 4,4′-bis(triethoxysilyl)-1,1′-biphenyl [BTSBP], 3-(trihydroxysilyl)propane-1-sulfonic acid [THSP], α-cyclodextrin (α-CD), β-cyclodextrin (β-CD), and γ-cyclodextrin (γ-CD). Encapsulated aromatic compounds possessing acidic hydroxyl groups such as BPAF, BPA, and FBPOH in the R_F-COOH/SiO₂ nanocomposites were found to exhibit no weight loss corresponding to the contents of aromatic compounds in the composites even after calcination at 800 °C. On the other hand, encapsulated aromatic compounds possessing no acidic hydroxyl groups such as BTSBP and aliphatic compounds (THSP, α-, β-, and γ-CD) gave a clear weight loss corresponding to the contents of these compounds in the composites after calcination. In addition, the fluorinated silica nanocomposite-encapsulated these compounds were applied to the surface modification of glass to exhibit a good oleophobicity with superhydrophilicity imparted by fluorinated carboxylic acid on the surface.

Reactions of mesomeric fluorocarbanions with acid anhydrides. Transformation of trifluoromethyl groups into fluorocarbonyl and perfluoroacyl groups

It was found that the reaction of mesomeric fluorocarbanions of the CF₃$\text{C}\text{θ}$XCOY type with benzoic anhydride leads to the loss of benzoyl fluoride and the formation of mesomeric carbanions of the FCO$\text{C}\text{θ}$XCOY type. In a similar reaction with perfluorocarboxylic acid anhydrides, besides a CF₃→COF transformation, further change of COF into COR_F is observed, leading to the formation of salts containing mesomeric anions of the R_FCO$\text{C}\text{θ}$XCOY type, which, upon acidification, give 1,1- -bis(perfluoroacyl)-2,2,2-trifluoroethanes CF₃CH(COR_F)₂ , tris- (perfluoroacyl)methanes (R_FCO)₃CH and bis(trifluoroacetyl)- acetic ester (CF₃CO)₂CHCOOMe. It has been shown that perfluoroalkyl groups in β-diketones and β,β′-triketones may hinder enolization despite their electron-attracting effect.     

Synthesis of fluorosilicone having highly fluorinated alkyl side chains based on the hydrosilylation of fluorinated olefins with polyhydromethylsiloxane

Hydrosilylation of fluorinated olefins with polyhydromethylsiloxane (PHMS) in the presence of a platinum catalyst was investigated to synthesize fluorosilicone having highly fluorinated alkyl side chains (R_f; C_nF_2n+1? ). The hydrosilylation of 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10‐heptadecafluoro‐1‐decene (C₈F₁₇CH?CH₂) ( 1 ) with poly(dimethylsiloxane‐co‐hydromethylsiloxane) {(CH₃)₃SiO[? (H)CH₃SiO? ]₈[? (CH₃)₂ SiO? ]₁₈Si(CH₃)₃} ( 4 ) converted the hydrogen bonded to silicons into the 3,3,4,4,5,5,6,6,7,7,8,8,9,9,10,10,10‐heptadecafluorodecyl group or fluorine bonded to silicons in the ratio of about 52:48, and the formation of the byproduct C₇F₁₅CF?CHCH₃ ( 8 ) was observed. The hydrosilylation of 7,7,8,8,9,9,10,10,11,11,12,12,13,13,14,14,14‐heptadecafluoro‐4‐oxa‐1‐tetradecene (C₈F₁₇CH₂CH₂OCH₂CH?CH₂) ( 2 ) with 4 converted the hydrogen bonded to silicons into the 7,7,8,8,9,9,10,10,11,11,12,12,13,13,14,14,14‐heptadecafluoro‐4‐oxa‐tetradocyl group bonded to silicons, but an excess amount of 2 was required to complete the reaction because the isomerization of 2 occurred in part to form C₈F₁₇CH₂CH₂OCH?CHCH₃ ( 9 ). The hydrosilylation of 4,4,5,5,6,6,7,7,8,8,9,9, 10,10,11,11,11‐heptadecafluoro‐1‐undecene (C₈F₁₇CH₂CH?CH₂) ( 3 ) with 4 converted the hydrogen bonded to silicons into the 4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11‐heptadecafluoroundecyl group bonded to silicons. This type of fluorinated olefin was successfully applied to the hydrosilylation with other PHMS's that involved a homopolymer of PHMS and a cyclic PHMS. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3120–3128, 2002     

Reactions of fluorinated silanes with 2-nitrocinnamates

The interaction of 2-nitrocinnamates with silicon reagents Me₃SiR_f (R_f = CF₃, C₂F₅, and C₆F₅) promoted either by sodium acetate in DMF or by tetrabutylammonium acetate in dichloromethane has been described. The reactions proceed as conjugate addition of fluorinated carbanion at the CC bond and afford 3-aryl-2-nitrobutanoates bearing a fluorinated substituent in good yields as diastereomeric mixtures in ratio from 1:1 to 1.6:1.     

Homoaldol condensation of aromatic ketones in fluoroalkyl end‐capped 2‐acrylamido‐2‐methylpropanesulfonic acid oligomeric gel network cores

Aromatic ketones such as 4′‐methoxyacetophenone (MAP), acetophenone (AP), 4‐acetylbiphenyl (ABP), and 2‐acetyl‐6‐methoxynapthalene (AMN) interacted with fluoroalkyl end‐capped 2‐acrylamido‐2‐methylpropanesulfonic acid oligomer [R_F‐(AMPS)_n‐R_F] at 80°C for 3 h to give the corresponding fluorinated oligomer/aromatic ketones composites. In these composites, the R_F‐(AMPS)_n‐R_F/MAP and /AP composites were found to give the homoaldol condensation products of MAP and AP, respectively. In contrast, the corresponding non‐fluorinated AMPS oligomer/MAP and sulfuric acid/MAP composites could not give the homoaldol product at all under similar conditions. This suggests that the R_F‐(AMPS)_n‐R_F oligomer could provide the suitable fluorinated oligomeric gel newtwok cores to interact with MAP or AP as a guest molecule, and the homoaldol condensation of encapsulated MAP and AP should proceed smoothly in the fluorinated oligomeric gel network cores. The R_F‐(AMPS)_n‐R_F/ABP and /AMN composites could not give the homoaldol products at all under similar conditions, indicating that the more bulky aromotic ketones than MAP or AP are not likely to be encapasulated as guest molecules into the fluorinated AMPS oligomeric gel netwok cores. Copyright © 2013 John Wiley & Sons, Ltd.     

Sorption of carbon dioxide in fluorinated poyimides

Sorption isotherms of CO₂ for ten fluorinated polyimides measured at 35°C and up to about 25 atm are analyzed according to the dual-mode sorption model. Sorption properties for these polyimides are compared with those for other glassy Polymers including unfluorinated polyimides. The glassy polymers with higher glass transition temperatures T_g tend to show greater CO₂ sorption. Introduction of a ? C (CF₃)₂? linkage into the repeat unit of the main chain increases the sorption by 20–80%. For glassy polymers, including the fluorinated and unfluorinated polyimides, the Langmuir affinity constant b and Henry's law solubility constant k_D are correlated with the content of functional (carbonyl or sulfonyl) groups [FG], and composite parameter reflecting the magnitude of both [FG] and free-space fraction V_F, respectively, with some exceptions. The Langmuir capacity constant C′_H is correlated with T_g, but there are two correlation lines; one for unfluorinated polyimides and a different one for other glassy polymers including fluorinated polyimides. The slope of the former group is smaller probably because of smaller differences in thermal probably because of smaller differences in thermal expansion coefficients in rubbery and glassy states. Most fluorinated polyimides show greater solubility of CO₂ than unfluorinated polyimides and other glassy polymers, because of their larger C′_H and k_D. © 1993 John Wiley & Sons, Inc.     

Perfluorinated and partially fluorinated organic compounds. Preparation,characterization and application

Electrochemical fluorination (ECF) of various heterocyclic compounds has been investigated. α,ω-Dimorpholinoalkanes of different chain length (n = 1-6) and of morpholinocyclohexene gave the perfluoro derivatives in yields up to 45%. The crystal and molecular structures of the perfluorinated compounds are presented. The mechanism of ECF for these compounds is discussed on the basis of a steric model. Perfluorocarbon emulsions of second generation were prepared by means of F-dimorpholines and F-cyclohexylmorpholine, acting both as oxygen carriers and as interfacial active compounds (IFACs). The stabilizing effect of these IFACs is interpreted. Semifluorinated alkanes, R_fR_h, are chemically inert and non-toxic. They are useful for blood substitutes in two ways: as co-surfactants to stabilize emulsions with perfluorocarbons and as oxygen carriers instead of perfluorocarbons. The high density of perfluorocarbons cause problems in some field of application in medicine. Therefore symmetrical diethers of the type R_F(CH₂)_mO(CH₂)_nO(CH₂)_mR_F were synthesized. These are inert and biocompatible compounds. Diethers with long R_F-tail and long hydrocarbon spacer are ideal solubilizers for perfluorocarbons with hydrocarbons and vice versa. The diethers with short hydrocarbon spacer and long R_F-tail can be applied in biological systems, because they are not soluble in lipid tissues. Perfluorocarbons (e. g. F-decalin, F-octane) are used as medical tools in ophthalmology, their purity is essential. Not totally fluorinated compounds (1 H-perfluoroalkanes, α,ω-dihydrogenoperfluoroalkanes) are characterized and discussed. 1H-perfluoroalkane is also formed by nucleophilic attack on perfluoroalkyl halide.     

Synthesis of aliphatic diamine and polyetherimide with long perfluoroalkyl side chain

The monomer, 2-(perfluorohexylmethyl)butan-1,4-diamine (TFD), was prepared from itaconic acid dimethyl ester via the addition of perfluorohexyl iodide followed by the gradual transformation of ester groups into amino groups. The polymerization of bisphenol-A diphthalic anhydride (BAPA) with TFD led to hydrophobic fluorinated polyetherimide (FPEI) with R_F=C₆F₁₃ side chain. This polymer makes it possible to cast films.     

Synthesis and properties of new fluorinated ester,thioester, and amide substituted polythiophenes. Towards superhydrophobic surfaces

A series of new fluorinated polythiophenes has been synthesized by oxidative chemical and electrochemical polymerization and by Ullmann coupling. The substitution with the perfluoroalkyl alkyl chain CH₂CH₂C₆F₁₃ on the 3 position of the thiophene ring is performed via an ester, thioester, or amide connector, (CH₂)_m‐C(O)X, m = 0–2, with a view to investigating the role of the linker on the polymerization and on the properties of the corresponding polymers. The bromination of the monomers at the 2 and 5 positions allows the use of Ullmann coupling to form soluble fluorinated oligomers. The electron affinity was determined from cyclic voltammetry and a value of 3.1 eV was found for the ester derivative; such materials represent interesting candidates for use in light‐emitting devices or as an electron accepting material in photodiodes/solar cells. The oxidative polymerizations need the connector to be spaced out from the heterocycle to reduce its withdrawal effect. The ester, thioester, and amide spacer determined to a large extent the efficiency of the oxidative polymerization, and particularly the electropolymerization, as well as the solubility of the polymers formed. All the polymers were analyzed by GPC and by UV–visible and fluorescence spectroscopies. The electrochemical oxidation of the thioester and amide group prevents the formation of electroactive films by electropolymerization. But in the case of the ester group, the electroformed polymer exhibits exceptional stable superhydrophobic and lipophobic properties because of a porous surface and the presence of a fluorinated chain that confers low surface energy. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4707–4719, 2007     

Interaction of rhenium hydride (η5-C5Me5)ReH(CO)(NO) with fluorinated alcoholswith fluorinated alcohols

The interaction between the fluorinated alcohols R^FOH (R^F=(CF₃)₂CH and (CF₃)₃C) and rhenium hydride (η⁵-C₅Me₅)ReH(CO)(NO) in hexane and liquid freon was studied in a wide temperature range by IR and¹H NMR methods, respectively. The formation of hydrogen-bonded complexes of two types, ReH...HOR^F and NO...HOR^F, was established. The hydride signal in the¹H NMR spectra at 96 K splits into two signals (at δ=−7.54 and −8.87) corresponding to the free ReH and the ReH...HO complex, respectively. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1405–1407, July, 1997.     

Low molecular weight aromatic compounds possessing a nonflammable characteristic in fluoroalkyl end‐capped acrylic acid oligomer/silica nanocomposite matrices after calcination at 800 °C under atmospheric conditions

Fluoroalkyl end‐capped acrylic acid oligomer [R_F‐(ACA)_n‐R_F] reacted with tetraethoxysilane and silica nanoparticles in the presence of low molecular weight aromatic compounds [ Ar‐H ] such as cetylpyridinium chloride (CPC) and bisphenol AF under alkaline conditions to afford R_F‐(ACA)_n‐R_F/SiO₂ nanocomposites‐encapsulated Ar‐H in 47–94% isolated yields. These fluorinated silica nanocomposites‐encapsulated Ar‐H can exhibit no weight loss behavior corresponding to the contents of Ar‐H after calcination at 800 °C under atmospheric conditions, although fluoroalkyl end‐capped acrylic acid oligomer in the nanocomposites decomposed completely under similar conditions. UV‐vis spectra of well‐dispersed methanol solutions of R_F‐(ACA)_n‐R_F/SiO₂/CPC nanocomposites before calcination show that CPC can be encapsulated into fluorinated silica nanocomposites with encapsulated ratios: 23–43%. The fluorinated nanocomposites after calcination was found to exhibit a higher antibacterial activity related to the presence of CPC in the composites. Encapsulated bisphenol AF into R_F‐(ACA)_n‐R_F/SiO₂ nanocomposites before and after calcination at 800 °C can exhibit a good releasing ability toward methanol with released ratios: 48 and 26%, respectively. ¹H MAS NMR, HPLC analysis, and LC‐MS spectra of R_F‐(ACA)_n‐R_F/silica nanocomposites‐encapsulated bisphenol AF also showed the presence of bisphenol AF in the nanocomposites even after calcination at 800 °C under atmospheric conditions. These findings suggest that CPC and bisphenol AF can exhibit a nonflammable characteristic in the fluorinated silica nanocomposites. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

The preparation of perfluorinated carboxylic esters and perfluoro carbonates

Aliphatic perfluorinated carboxylic esters have been prepared by two methods; (i) the reaction of the potassium salt of perfluoro 3-ethyl pent-3-ol, KOC(C₂F₅)₃, with perfluoro acid chlorides R_fCOCl, to yield perfluorinated esters of composition R_fCOOC(C₂F₅)₃, and (ii) the reaction of carbonyl chloride or thionyl chloride with a mixture of the potassium salt KOC(C₂F₅)₃ and perfluoro acid salts of the general formula KOCOR_f in a polar solvent. The product ester has the composition R_fCOOC(C₂F₅)₃, and in this instance carbon dioxide or sulphur dioxide is liberated during the reaction. A qualitative study of the thermal decomposition of a perfluoro ester has been made.A tertiary perfluoro carbonate of composition [(C₂F₅)₂CF₃CO]₂CO has been prepared by the reaction of phosgene with the potassium salt KOC(C₂F₅)₂CF₃ in a polar solvent. The intermediate acid chloride (C₂F₅)₂CF₃COCOCl can be isolated.     

Solubilization and applications of single-walled carbon nanotubes into aqueous and organic media by the use of nanometer size-controlled fluoroalkyl end-capped oligomeric aggregates

We have studied on the solubilization of single-walled carbon nanotubes (SW-CNTs) into aqueous and organic media by the use of a variety of nanometer size-controlled fluorinated self-assemblies, which were formed by the aggregations of end-capped fluoroalkyl segments in fluoroalkyl end-capped acrylic acid oligomers [R_F-(ACA)_n-R_F], N,N-dimethylacrylamide oligomers [R_F-(DMAA)_n-R_F], acryloylmorpholine oligomers [R_F-(ACMO)_n-R_F], and N-(1,1-dimethyl-3-oxobutyl)acrylamide oligomers [R_F-(DOBAA)_n-R_F]. Fluorinated self assemblies formed in organic media (colorless solutions) could solubilize SW-CNTs into organic media to afford the transparent pale yellow solutions. The dynamic light scattering measurements showed that the size of fluorinated self-assemblies increased after the solubilization of SW-CNTs into organic media. It was suggested that the solubilization of SW-CNTs into organic media is due to the encapsulation of SW-CNTs into fluorinated assemblies. Fluorinated assemblies were also able to solubilize SW-CNTs into water to give the transparent gray solutions. Among a variety of fluorinated assemblies, fluorinated assemblies formed by R_F-(ACMO)_n-R_F [R_F = CF(CF₃)OC₆F₁₃] oligomer was more effective for the solubilization of SW-CNTs into both aqueous and organic media. Contact angle measurements of dodecane and the fluorescence spectra for poly(methyl methacrylate) cast film modified by fluorinated self-assemblies—SW-CNTs complexes showed that SW-CNTs are dispersed above the PMMA surface.