Colorimetric determination of traces of selenium, tellurium, manganese and cerium

Methods are described for the colorimetric determination of micro- and semi-micro quantities of selenium, tellurium, cerium and manganese. The test solution in 0.35-3M condensed phosphoric acid medium is oxidized with an excess of permanganate. The colour intensity of the unreacted permanganate is measured at 530 nm.     

Na2EDTA滴定法测定粗二氧化碲中铅含量

建立了用氢溴酸消除锑、砷、锡干扰,用硫酸将铅形成硫酸铅沉淀,再用EDTA络合滴定法测定粗二氧化碲中铅量的方法。试样用硝酸、盐酸溶解,用硫酸沉淀铅,氢溴酸消除锑、砷、锡的干扰后,过滤分离其他共存元素,以乙酸-乙酸钠缓冲溶液溶解硫酸铅沉淀,在pH=5.0～6.0时,以二甲酚橙作指示剂,用Na_2EDTA溶液滴定溶液中铅含量。实验结果表明,氢溴酸加入量为15mL,酒石酸加入量为10mL,沉淀体积为50～60mL,沉淀时间1h以上时,方法相对标准偏差(RSD)在0.10%～1.1%,加标回收率为97.1%～102%,满足粗二氧化碲中铅量的生产控制检测要求。     

Determination of the O/M ratios of polynary uranium oxides by Ce(IV)-Fe(II) back titration after dissolution in mixed sulphuric and phosphoric acids

Uranium (IV) in polynary uranium oxides is determined after the solid has been dissolved in a warm mixed solution of sulphuric and phosphoric acids containing excess Ce(IV). The latter is titrated with a Fe(II) standard solution using ferroin as indicator. This method is especially effective for (mixed) uranium oxides which are difficult to dissolve in hot Ce(IV) sulphuric acid. The standard deviation of the determined x value in polynary oxides is estimated to be below +/- 0.004 for samples of 10-30 mg.     

Titration of cerium (IV) sulphate with sodium oxalate at the room temperature using ferroin as internal indicator

Summary A method has been developed for the titration of cerium(IV) sulphate with sodium oxalate at the room temperature, using ferroin as internal indicator. A new principle has been utilised for facilitating the indicator action at the equivalence point. This involves the use of a photochemical reaction between the oxalate and iron(III) which is deliberately added to the mixture containing cerium(IV) sulphate and ferriin. When the mixture is titrated with the sodium oxalate solution under exposure to the light from a Philips Repro lamp, the addition of a very slight excess of sodium oxalate solution, after all the cerium(IV) sulphate has reacted, produces a vivid red colour. The slight excess of sodium oxalate added reacts with the iron(III) salt photochemically producing a trace of iron(II) salt which reduces the ferriin to the red ferroin. In titrations with 0.1 and 0.05 N solutions of sodium oxalate, the error is negligible. In titrations with sodium oxalate solution of lower strengths, the error amounts to 0.02 ml of 0.01 N oxalate which has to be subtracted from the titre.     

Volumetric studies in oxidation-reduction reactions: Reduction with ferrous ethylenediamine sulphate ceric sulphate method

Ferrous ethylenediamine sulphate has been used as a reducing agent in acid medium for the indirect volumetric estimations of potassium chlorate, potassium bromate, potassium metaperiodate, potassium dichromate, potassium ferricyanide, potassium permanganate, potassium persulphate, hydrogen peroxide and ceric sulphate. The excess of ferrous ethylenediamine sulphate added to each of the substances in acid medium was titrated with standard ceric sulphate solution using ferroin as an indicator.     

Determination of the O/M ratios of polynary uranium oxides by Ce(IV)-Fe(II) back titration after dissolution in mixed sulphuric and phosphoric acids

Uranium (IV) in polynary uranium oxides is determined after the solid has been dissolved in a warm mixed solution of sulphuric and phosphoric acids containing excess Ce(IV). The latter is titrated with a Fe(II) standard solution using ferroin as indicator. This method is especially effective for (mixed) uranium oxides which are difficult to dissolve in hot Ce(IV) sulphuric acid. The standard deviation of the determined x value in polynary oxides is estimated to be below ± 0.004 for samples of 10–30 mg.     

Redox indicators in titrations in aqueous nitric acid

Iron(II) in nitric acid solution can be titrated with dichromate (and vice versa), diphenylamine, N-phenylanthranilic acid, ferroin, or brucine being used as indicator. Fluoride is added when one of the first three is used, and urea if the last is used. Citric, oxalic and tartaric acids, arsenic(III) and mercury(I) interfere in the titration.     

Sequential titration of iron(II), antimony(III) and arsenic(III) in binary or ternary mixture

A simple titrimetric procedure for the determination of iron(II), antimony(III) and arsenic-(III) in a mixture, with cerium(IV) sulphate as titrant, is proposed. The end-points can all be detected with ferroin or potentiometrically. Phosphoric acid medium is used for titration of the iron(II), then acetic acid medium for the titration of antimony(III), and finally the arsenic(III) is titrated in presence of iodine as catalyst. The procedure utilizes a single portion of test solution; it can be adopted for the analysis of binary mixtures.     

Ammonium hexanitratocerate(IV) as an oxidizing agent-VI Determination of chronuum(III) through oxidation to chromium(VI) at room temperature

A new method has been developed for the determination of chromium(III), depending on its oxidation to chromium(VI) at room temperature by treatment with 50-100% excess of ammonium hexanitratocerate(IV) in 1.0M nitric acid medium. The reaction is complete within 15 min. The unreacted cerium(IV) is titrated potentiometrically with sodium oxalate.     

A new volumetric method for the determination of molybdenum(VI)

Summary A new volumetric method has been developed for the determination of molybdenum(VI). The method consists in the reduction of molybdenum(VI) by heating with a slight excess of hydrazine sulphate in 1 to 2 M hydrochloric acid medium for ten minutes on a water bath. The mixture is cooled and the molybdenum(V) obtained determined by titration with a standard solution of ceric sulphate at an overall acidity of 4 N hydrochloric acid, using diphenyl benzidine as indicator and adding 5 ml of syrupy phosphoric acid for 50 ml of the mixture. Alternately the molybdenum(V) can be titrated with a standard solution of ceric sulphate at an overall acidity of 3 N hydrochloric acid using ferroin as indicator and adding 5 ml of syrupy phosphoric acid for 50 ml of the titration mixture. The molybdenum(V) can also be titrated with a standard solution of sodium vanadate in 8 N sulphuric acid medium, using N-phenyl anthranilic acid as indicator. Alternately, the titration with sodium vanadate can be made with diphenyl benzidine as indicator in 4 N acid medium, adding 5 ml of syrupy phosphoric acid and 1 ml of 1.0 M oxalic acid to catalyse the indicator action. The method now proposed is much more convenient than the methods currently available. It is simple because it does not require any costly chemicals or complicated apparatus. Furthermore, it has the advantages of great rapidity and excellent precision.     

Simple conditions for the use of ferroin indicator in cerimetric titrations of antimony(III) alone and in mixtures with arsenic(III)

The titration of antimony(III) with cerium(V) sulphate in the presence of ferroin indicator at room temperature is entirely satisfactory in media consisting of 50% ($\text{v}\text{v}$) acetic acid and 1–3 M hydrochloric acid. In the absence of acetic acid, ferroin reacts with the antimony(V) formed in the very early stages, to give a sparingly soluble red complex, which remains in suspension and resists oxidation by cerium(IV). This titration provides a rational method for sequential visual titrations of antimony(III) and arsenic(III). The composition of the ferroin-antimony(V) complex is discussed. Titrations of antimony(III) in 0.5–1 M sulphuric acid medium do not require acetic acid but need iodine monochloride catalyst.     

Some new applications of ferroin as redox indicator in titrations with dichromate

Working conditions for the titration of arsenic(III), hydroquinone, ferrocyanide, uranium(IV) and molybdenum(V) with dichromate in sulphuric acid and hydrochloric acid media have been established, with ferroin as the redox indicator.     

Determination of trace arsenic, antimony, selenium and tellurium in various oxidation states in water by hydride generation and atomic-absorption spectrophotometry after enrichment and separation with thiol cotton

A novel procedure for determination of trace As(III) and As(V), Sb(III) and Sb(V), Se(IV) and Se(VI), Te(IV) and Te(VI) in water by atomic-absorption spectrophotometry after separation and enrichment with "thiol cotton" and hydride generation has been established. The sorption behaviour of various oxidation states of arsenic, antimony, selenium and tellurium, and the conditions of quantitative sorption and desorption of these species were studied. The procedures for reducing species from higher oxidation states were optimized. Interferences from other species and their elimination were investigated. The selectivity of the procedure for the determination of species in higher and lower oxidation states was examined. The procedure has been successfully used to determine arsenic, antimony, selenium and tellurium in water, in the range from pg ml to ng ml . The recoveries for added spikes were in the range 90-110%, with coefficients of variation in the range 3-8%     

Ammonium hexanitratocerate(IV) as an oxidizing agent-V Titrimetric determination of arsenic(III) at room temperature

Conditions have been established for the accurate titration of arsenic(III) with ammonium hexanitratocerate(IV) at room temperature in sulphuric, nitric and hydrochloric acid media, using suitable catalysts, and ferroin as indicator.     

Analysis of tellurides of lead and tin by automatic titrations

An analytical method based on automatic potentiometric EDTA and redox titrations was developed for the analysis of tellurides of lead and tin.First, the sum of lead and tin is titrated at pH 4.5 by adding a known excess of EDTA and back-titrating with a standard lead solution. After addition of ammonium fluoride to mask the tin, the EDTA released from the Sn-EDTA complex is titrated with standard lead solution. Alternatively, after the determination of total lead and tin, lead may be determined by back-titration with standard lead on a separate sample aliquot using tartaric acid to mask the tin. Tellurium is separated as tellurous acid, which is then dissolved in a dilute sulfuric acid solution and oxidized by permanganate at room temperature; the excess permanganate is back-titrated with iron(II) solution automatically. This titration may also be used to determine tellurium in the presence of lead and tin after treatment with perchloric acid. Accuracies of 0.1-0.2% can be obtained.     

Analytical aspects of some organic acids

Summary Back titrimetric procedures for the estimation of aluminium, zirconium, and thorium have been developed, which involved the adjustment of the concentration of the metallic salts, concentration of EDTA,ph, and temperature, addition of indicator solution (namely, 2-hydroxy3-naphthoic acid and back titration with standard 0.1 M ferric chloride solution. This method is based on the fact that the excess EDTA, which is added to the metal solutions may be back titrated with iron(III), which forms a highly coloured complex with the indicator, when present in slight excess. Quantities of aluminium, zirconium and thorium as small as 10.8, 4.6, 11.6 mg respectively, can be back titrated with in experimental error, when present in a volume of 100 ml.Part IV: See Z. analyt. Chem. 172, 356 (1960).     

Stability studies of arsenic, selenium, antimony and tellurium species in water, urine, fish and soil extracts using HPLC/ICP-MS

The stability of arsenic, selenium, antimony and tellurium species in water and urine (NIST SRM 2670n) as well as in extracts of fish and soil certified reference materials (DORM-2 and NIST SRM 2710) has been investigated. Stability studies were carried out with As(III), As(V), arsenobetaine, monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), phenylarsonic acid (PAA), Se(IV), Se(VI), selenomethionine, Sb(III), Sb(V) and Te(VI). Speciation analysis was performed by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Best storage of aqueous mixtures of the examined species was achieved at 3 degrees C whereas at -20 degrees C species transformation especially of selenomethionine and Sb(V) took place and a new selenium species appeared within a period of 30 days. Losses and species transformations during extraction processes were investigated. Extraction of the spiked fish material with methanol/water led to partial conversion of Sb(III), Sb(V) and selenomethionine to two new antimony and one new selenium species. The other arsenic, selenium and tellurium species were almost quantitatively extracted. For soil spiked with MMA, PAA, Se(IV) and Sb(III), recoveries after extraction with water and sulfuric acid (0.01 mol/L) were below 20%.     

Separation of selenium(IV) and tellurium(IV) from mixtures by extraction chromatography with trioctylphosphine oxide

The reversed-phase extraction chromatographic separation of selenium(IV) and tellurium(IV) from several elements with trioctylphosphine oxide as extractant is reported. Selenium was extracted from 6M hydrochloric acid containing 7M lithium chloride was stripped with 4M hydrochloric acid, and tellurium was extracted from either the same medium as selenium or from 4M hydrochloric acid, and stripped with 1-2M hydrochloric acid. Selenium and tellurium can be separated from multicomponent mixtures.     

Titrimetric assay of ofloxacin in pharmaceuticals using cerium(IV) sulphate as an oxidimetric reagent

Two titrimetric methods which are simple, rapid, cost-effective and eco-riendly are described for the determination of ofloxacin (OFX) in bulk drug and in tablet formulations based on the oxidation of OFX by Ce(IV) sulphate. In direct titrimetry (method A), the acidified solution of OFX is titrated directly with Ce(IV) sulphate using ferroin as indicator, and indirect titrimetry (method B) involves the addition of known excess of Ce(IV) sulphate to an acidified solution of OFX followed by the determination of unreacted oxidant by back titration with ferrous ammonium sulphate (FAS) using the same ferroin indicator. In both the methods, the amount of Ce(IV) sulphate reacted corresponds to OFX concentration. Method A and method B permit the determination of OFX over the concentration range of 1.5?C15 mg in both the methods and the quantitation is based on a 1: 5 reaction stoichiometry (OFX: Ce (IV) sulphate). The methods were statistically evaluated by calculating percent relative error (% RE) for accuracy and percent relative standard deviation (% RSD) for precision, and were applied successfully to the determination of OFX in tablets with mean recoveries in the range of 96.50?C98.42%. No interference was observed from common additives found in pharmaceutical preparations. The accuracy and reliability of the methods were further ascertained by performing recovery tests s standard-addition technique.     

Determination of sulphide, sulphite and thiosulphate with thallic perchlorate or sulphate

Sulphide, sulphite and thiosulphate can be determined separately or in admixture, with thallic perchlorate or sulphate in acid medium. A sample solution is rendered approximately 0.5 M in acid, 5 ml of 0.05 M KI are added and the solution is titrated to a starch end-point with thallium(III) solution. In another method an acid sample solution is titrated with thallium(III) or iodine solution in the presence of indigo carmine indicator. The end-point is improved in the presence of Co(II).