Neutron activation analysis of high purity nickel by solvent extraction using 2-benzylpyridin/benzene

A radiochemical neutron activation analysis using solvent extraction has been applied for the determination of trace impurities in high purity nickel. Because of the high activity of⁵⁸Co produced by the nuclear reaction,⁵⁸Ni(n,p)⁵⁸Co, cobalt should be separated from the impurities. Removal of cobalt from the other trace elements in the aqueous acidic solution containing 1M thiocyanate ion (KSCN) was achieved by extraction with 1M2-benzylpyridin (BPy) in benzene. From the result of tracer experiments, cobalt was completely separated from most other elements except Fe, Mo and Zn. To determine the experimental accuracy, NIST SRM 673 nickel oxide was analyzed and the results agreed well within 10% deviation. This established radiochemical method was applied to the analysis of high purity nickel samples.     

A Growing Drop Technique for Measuring Dynamic Interfacial Tension

A novel, growing drop technique is described for measuring dynamic interfacial tension due to sorption of surface-active solutes. The proposed method relates the instantaneous pressure and size of expanding liquid drops to the interfacial tension and is useful for measuring both liquid/gas and liquid/liquid tensions over a wide range of time scales, currently from 10 ms to several hours. Growing drop measurements on surfactant-free water/ air and water/octanol interfaces yield constant tensions equal to their known literature values. For surfactant-laden, liquid drops, the growing drop technique captures the actual transient tension evolution of a single interface, rather than interval times as with the classic maximum-drop-pressure and drop-volume tension measurements. Dynamic tensions measured for 0.25 mM aqueous 1-decanol solution/air and 0.02 kg/m³ aqueous Triton X-100 solution/dodecane interfaces show nonmonotonic behavior, indicating slow surfactant transport relative to the imposed rates of interfacial dilatation. The dynamic tension of a purified and fresh 6 mM aqueous sodium dodecyl sulfate (SDS) solution/air interface shows only a monotonic decrease, indicating rapid surfactant transport relative to the imposed rates of dilatation. Conversely, an aged SDS solution, naturally containing trace dodecanol impurities, exhibits dynamic tensions which reflect a superposition of the rapidly equilibrating SDS and the slowly adsorbing dodecanol.     

The interface air/water of n-dodecanephosphonic acid solutions

 The air/water interface of the system n-dodecanephosphonic acid (H₂DP)–water was studied by surface tension, ion-selective electrodes and evaporation in an electrobalance. The combination of surface tension and ion-selective electrodes measurements enables to study the adsorption of soluble surfactants above the cmc using the Gibbs’ equation. H₂DP formed a nonideal monolayer at the air/water interface with A _molec=0.995 nm² below the cmc. Above the cmc there was a reduction in adsorption giving A _molec=6.32 nm², which remained almost constant in the explored concentration range. This adsorption reduction may be due to a change composition on micellization, or to a thermodynamic advantage of micellization on adsorption. The reduction in the evaporation rate of water was mainly due to the reduction of the water activity, caused by the presence of solutes in bulk. This is because the strong changes in the surface coverage did not have significant influence on the evaporation rate. Received: 6 January 1997 Accepted: 15 August 1997     

Impurity and phase compositions of the surface of CdxHg1?xTe solid solutions

The results of our studies of the real surface impurity and phase compositions of Cd _x Hg_{1 − x} Te solid solutions and changes in the compositions induced by thermal evacuation and ion bombardment are presented. The impurity and phase compositions of the surface of CdHgTe solid solutions exposed to air included the gases and vapors (CO, O₂, H₂O) and hydrocarbons adsorbed from the atmosphere. Thermal vacuum treatment of the samples at 615 K led to surface purification from organic impurities, oxygen, water, and mercury microinclusions. The Cd _x Hg_{1 − x} Te sample surface was completely cleaned and its stoichiometric composition achieved by ion etching to a depth of 100 ?.     

A Nonpolar,Nonamphiphilic Molecule Can Accelerate Adsorption of Phospholipids and Lower Their Surface Tension at the Air/Water Interface

The adsorption dynamics of a series of phospholipids (PLs) at the interface between an aqueous solution or dispersion of the PL and a gas phase containing the nonpolar, nonamphiphilic linear perfluorocarbon perfluorohexane (PFH) was studied by bubble profile analysis tensiometry. The PLs investigated were dioctanoylphosphatidylcholine (DiC₈‐PC), dilaurylphosphatidylcholine, dimyristoylphosphatidylcholine, and dipalmitoylphosphatidylcholine. The gas phase consisted of air or air saturated with PFH. The perfluorocarbon gas was found to have an unexpected, strong effect on both the adsorption rate and the equilibrium interfacial tension (γ_eq) of the PLs. First, for all of the PLs, and at all concentrations investigated, the γ_eq values were significantly lower (by up to 10 mN m^?1) when PFH was present in the gas phase. The efficacy of PFH in decreasing γ_eq depends on the ability of PLs to form micelles or vesicles in water. For vesicles, it also depends on the gel or fluid state of the membranes. Second, the adsorption rates of all the PLs at the interface (as assessed by the time required for the initial interfacial tension to be reduced by 30 %) are significantly accelerated (by up to fivefold) by the presence of PFH for the lower PL concentrations. Both the surface‐tension reducing effect and the adsorption rate increasing effect establish that PFH has a strong interaction with the PL monolayer and acts as a cosurfactant at the interface, despite the absence of any amphiphilic character. Fitting the adsorption profiles of DiC₈‐PC at the PFH‐saturated air/aqueous solution interface with the modified Frumkin model indicated that the PFH molecule lay horizontally at the interface.     

A photoelectrochemical study on the features of carbonate-catalyzed water oxidation at illuminated TiO2/Solution interface

Photoelectrochemical (PEC) measurements were performed to investigate the catalytic effect of carbonate on water splitting over TiO₂ nanotube photoanode at low applied potentials. The photocurrent measured with the presence of carbonate with a low concentration of 5?×?10^?3?M in 0.5 M NaClO₄ solution of pH?=?6–13 was ca. two to seven times of that measured in the absence of carbonate in solution. By adding a small amount of formate as a precursor of in situ generated carbonate in solution, the significant catalytic effect of carbonate was further evidenced. The features of the photocurrents measured under both potential dynamic and potentiostatic conditions indicated that the existence of carbonate in solution can effectively prevent the surface recombination of the photogenerated electron–hole pairs occurring at the TiO₂/solution interface, which was regarded as the main reason for the catalytic effect of carbonate on the PEC water splitting in this work. The related charge transfer processes during water photooxidation at the TiO₂/solution interface were discussed.     

Electrochemistry of TEMPO: an assessment of the water diffusion constant in the aqueous liquid/vapor interfacial region

TEMPO, 2,2,6,6-tetramethylpiperidnyl-1-oxy, is a weak surfactant exhibiting a reversible redox activity: a one-electron oxidation to its oxonium cation. In the course of our earlier work (ref. Wu et al. in J Am Chem Soc 127:4490–4496, 2005; Glandut et al. in J Phys Chem B 110:6101–6109, 2006; Glandut et al. in Langmuir 22:10697–10704, 2006), we developed a full understanding of TEMPO’s electrochemistry at line microband electrodes. In these experiments TEMPO diffuses to the line electrode residing in the plane of the air/water interface in two coupled media, bulk aqueous phase with D?=?7.7?×?10^?6 cm²/s and along the 2D air/water interface with at least an order of magnitude greater surface diffusion constant, D _surf. The magnitude of the TEMPO oxidation current depends jointly on D _surf and on the rate of surface partitioning expressed by the desorption rate constant, k _des. The population of TEMPO partitioned to the air/water interface is largely unsolvated and couples to the aqueous solution by hydrogen bonding to predominately one water molecule. Our experimental methodology allows us to simultaneously determine D _surf and k _des by recording TEMPO voltammetric curves with line microband and barrier microband electrodes. In this report, we present a new methodology of producing and characterizing barrier microband electrodes using vapor-deposited SiO and introduce additional measures such as aspiration of the air/water interface designed to substantially reduce if not eliminate negative error due to surface impurities. These investigations generated a more accurate value of D _surf of 1.0?±?0.3?×?10^?4 cm²/s which we discuss in terms of the dynamic properties of water in the air/water interfacial region.     

Microsphere resin chromatography combined with microbial biotransformation for the separation and purification of salvianolic acid B in aqueous extract of roots of Salvia multiorrihza Bunge

Salvianolic acid B was separated and purified from Salvia miltiorrhiza Bunge (danshen) by microbial transformation together with chromatography of microsphere resin. The aqueous extract of danshen was transformed by Fusarium graminearum in a bioreactor containing phosphate buffer (PBS), in which rosmarinic acid was transformed into danshensu and caffeic acid and the yield of salvianolic acid B was higher than 85%. After biotransformation, salvianolic acid B was purified by microsphere resin. A parallel test for making a comparison of microsphere resin chromatography between elution by methanol water solution and water was done. The purity of salvianolic acid B was up to 95% at the yield of 62% when impurities and salvianolic acid B were eluted by 45% and 55% methanol solution respectively. The purity of salvianolic acid B was up to 99% at the yield of 90% when distilled water was used to elute the impurities and salvianolic acid B. The total yield of salvianolic acid B was up to 75% at the purity over 99% while biotransformation combined with microsphere resin chromatography by water elution. Microbial biotransformation together with water elution of microsphere resin supplied an efficient method to eliminate the micromolecular impurities and a possible method to purify water-soluble compounds in traditional Chinese medicine.     

Anodic Stripping Voltammetric Determination of Lead in Tap Water at an Ordered Mesoporous Carbon/Nafion Composite film Electrode

A sensitive mercury‐free lead (Pb²⁺) sensor has been proposed based on an ordered mesoporous carbon and Nafion composite film (OMC/Nafion) coated glassy carbon electrode. The analysis of Pb²⁺ using anodic stripping voltammetry (ASV) includes two steps. Pb²⁺ ions are firstly reduced and deposited on the electrode surface in a Pb²⁺ solution (10 mL) during a preconcentration step biased at ?1.0 V, followed by a measurement step by differential pulse voltammetry (DPV) within the potential range of ?0.8 to ?0.3 V (scan rate: 20 mV/s, frequency: 20 Hz, amplitude: 50 mV, pulse width: 50 ms). Linear calibration curve was found to be from 20 nM to 2 μM for Pb²⁺ with a sensitivity of 17.4±1.38 μA/μM after a 5‐min of preconcentration. The detection limit was estimated to be around 4.60±0.12 nM at the signal to noise ratio of 3. Reproducibility (RSD%) was found to be 3.0% for a single sensor with eight measurements and 4.3% for five sensors prepared with identical procedures. The practical application of the proposed lead sensor was verified by determination of trace level of Pb²⁺ in tap water sample.     

Lysozyme binding to poly(4-vinyl-N-alkylpyridinium bromide)

The adsorption behavior of polycations at ionic strengths (I) ranging from 0.001 to 0.1 onto silicon wafers was studied by means of ellipsometry, contact angle measurements and atomic force microscopy (AFM). Polycations chosen were bromide salts of poly(4-vinylpyridine) N-alkyl quaternized with linear aliphatic chains of 2 and 5 carbon atoms, QPVP-C2 and QPVP-C5, respectively. Under I=0.001 the reduction of screening effects led to low adsorbed amounts of QPVP-C2 or QPVP-C5 (1.0±0.1 mg/m²), arising from the adsorption of extended chains. Upon increasing I to 0.1, screening effects led to conformational changes of polyelectrolyte chains in solution and to higher adsorbed amount values (1.9±0.2 mg/m²). Advancing contact angle θ_a measurements performed with water drops onto QPVP-C2 and QPVP-C5 adsorbed layers varied from (45±2)° to (50±5)°, evidencing the exposure of both hydrophobic alkyl groups and charged moieties. The adsorption of lysozyme (LYZ) molecules to QPVP-C5 layers was more pronounced than to QPVP-C2 films. Antimicrobial effect of LYZ bound to QPVP-C2 or QPVP-C5 layers or to Si wafers was evaluated with enzymatic assays using Micrococcus luteus as substrates. The adsorption behavior of QPVP-C2 and QPVP-C5 at the water–air interface was studied by means of surface tension measurements. Only QPVP-C5 was able to reduce water surface tension. Mixtures of LYZ and QPVP-C5 were more efficient in reducing surface tension than pure LYZ solution, evidencing co-adsorption at liquid–air interface. Moreover, antimicrobial action observed for mixtures of LYZ and QPVP-C5 was more pronounced than that measured for pure LYZ. Hydrophobic interaction between LYZ and QPVP-C5 in solution seems to drive the binding and to preserve LYZ secondary structure.     

Adsorption at the air/water interface in dodecylammonium chloride/sodium dodecyl sulfate mixtures

The composition and properties of the adsorption films of dodecylammonium chloride/sodium dodecyl sulfate at the air/water interface depend on interactions between the film molecules and equilibria in the bulk phase (monomer-micelle and/or monomerprecipitate equilibria).The negative value of surface molecular interaction parameter ^mon calculated using the regular solution theory indicates strong attractive interactions between adsorbed molecules. Electrostatic interactions between oppositely charged ionic head groups enhance the adsorption of surfactants and decrease the minimum molar area of surfactant molecules at the air/water interface. The addition of an oppositely charged surfactant enhances packing at the air/water interface and transition from a liquid expanded to a liquid condensed state. Surface potential measurements reveal positive values for the mixtures investigated, implying the cationic surfactant ions are closer to the surface than the anionic ones.     

Dependence of the energy of surface-active substances/metal interaction on their ionization potentials. Evaluation of hydrophilicity of metal

The function Δ(ΔG _A ⁰), which is the difference of Gibbs energies characterizing surface-active substance (surfactant, SAS) adsorption at metal/solution and air/solution surfaces, has been introduced. The equation connecting the function Δ(ΔG _A ⁰) with SAS ionization potential has been obtained using the elementary theory of donor-acceptor interactions. Published experimental data on SAS adsorption at mercury, bismuth and gold have been used for Δ(ΔG _A ⁰) calculation. The dependence of Δ(ΔG _A ⁰) on ionization potentials can be described by an equation derived in this work. It has been demonstrated that the value of the hydrophilicity of gold is much higher than the values for mercury and bismuth. The lifetime of SAS molecules at a metal surface has been estimated. The question of the possibility of theoretica l estimation of standard energies ΔG _A ⁰ characterizing SAS adsorption at a metal/solution surface has been discussed. Received: 9 December 1996 / Accepted: 13 January 1997     

Removal of complexed mercury by dithiocarbamate grafted on mesoporous silica

Mesoporous silica (MCM-41) with d ₍₁₀₀₎ interplanar distance of 38 Å was prepared by a room temperature process through low surfactant templation technique. The surface of MCM-41 was functionalized with dithiocarbamate (dtc) ligand, named as MCM-41-dtc and this was characterized by X-ray diffraction, BET surface area, particle size analysis, ²⁹Si MAS NMR spectra and sulphur analysis. The sorption of mercury from 0.1M HCl solution by MCM-41-dtc was studied as a function of pH, [Hg²⁺], time and temperature. The sorption data obtained at various initial concentrations of mercury were fitted into Langmuir adsorption model. Mercury speciation in solution and the sorption capacity measurements indicated possible formation of a 1 : 1 square planar complex in the solid phase. A very rapid sorption of mercury was observed in the initial stages of equilibration, which can be attributed to the large surface area, wide porosity and fine particle size of MCM-41-dtc, facilitating facile accessibility of mercury into the inner pores of the sorbent. The enthalpy change accompanied by the sorption of mercury was found to decrease from 83.7 to 6.2 kJ/mol, when the initial concentration of mercury was increased from 5^.10^-4M to 1.5^.10^-3M.     

Determination of trace amounts of nitrite by single-sweep polarography

A single-sweep polarographic determination of nitrite in 0.2 M sulphuric acid medium containing nickel(II) sulphate and ammonium thiocyanate is described. The ternary complex (NiSCNNO)⁺ which is formed in the solution is strongly adsorbed on the surface of the mercury electrode and an adsorptive polarographic wave at ?0.57 V (vs. SCE) is related to the concentration of nitrite in the range 2.0 × 10^?8-1.0 × 10^?6 M. The detection limit is 8 × 10^?9 M. The relative standard deviation is 1.5% and the regression coefficient is 0.998. Most common anions and cations do not interfere. The mechanism of the electrode process was studied by several electrochemical methods. The polarographic wave is attributed to the reduction of nitrogen monoxide in the adsorbed (NiSCNNO)⁺ complex to hydroxylamine. The procedure was applied to the determination of trace amounts of nitrite in sausage, water and nitrate.     

Solid-phase extraction and determination of ultra trace amounts of lead,mercury and cadmium in water samples using octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid) and atomic absorption spectrometry

A simple and fast method for preconcentration and determination of ultra trace amounts of lead(II), mercury(II) and cadmium(II) in water samples is presented. Lead, mercury and cadmium adsorbed quantitatively during passage of water samples (pH?=?7, flow rate?=?20 mL min^?1) through octadecyl silica membrane disks modified with 5,5′-dithiobis(2-nitrobenzoic acid). The retained lead, mercury and cadmium are then stripped from the disk with a minimal amount of 1 M hydrochloric acid solution as eluent, and determined by atomic absorption spectrometry. The influence of flow rates of the eluent and sample solution, the amount of ligand, type and least amount of eluent, pH of sample, effect of other ions and breakthrough volume are determined. The breakthrough volume of the method is greater than 2000 mL for lead and greater than 1500 mL for mercury and cadmium, which results in an enrichment factor of 200 for lead and an enrichment factor of 150 for both mercury and cadmium. The limit of detection of the proposed method is 177, 2 and 13 ng l^?1 for lead, mercury and cadmium, respectively.     

Determination of methyl mercury in water samples with electromagnetic induction thermal desorption/pyrolysis coupled to atomic fluorescence spectrometry

A novel non-chromatographic method for the pre-concentration and determination of trace methyl mercury in water samples has been proposed. This method included two main steps: (1) The methyl mercury in sample solution was adsorbed on PDMS of the Fe/SiO₂/PDMS bed enrichment column; (2) the analyte was thermally desorbed from the enrichment column and pyrolysed to Hg⁰ in an iron particle bed pyrolysis column by using electromagnetic induction heating technique, and then detected by an on-line coupled atomic fluorescence detector. Several factors affecting the enrichment column preparation and concentration procedure have been investigated and optimised. Under optimal condition, the detection limit (3σ) was 0.2 ng L^–1, along with relative standard deviations of 2.4% (10 ng L^–1, N = 11) for the repeatability study. The enrichment factor obtained was 108. The two standard reference materials (GBW08675, GBW10029) were analysed to validate the present method. This method was successfully applied to the determination of ng L^–1 methyl mercury in water samples.     

Electrochemical reduction of NAD+ and pyridinium cations adsorbed at the mercury/water interface: Electrochemical behavior of adsorbed pyridinyl radicals

Neutralization of the positive charge of the pyridinium cation (Pyr⁺)_ads adsorbed at the mercury/water interface following electrochemical reduction is likely to provoke a very fast flat-to-perpendicular reorientation of the adsorbed species, thus rendering the perpendicularly adsorbed radical (Pyr)_ads electrochemically inactive. Therefore, it cannot be ascertained by means of cyclic voltammetry whether dimerization of the (Pyr)_ads radicals, which occurs in solution, also occurs at the mercury/water interface.     

Trace Detection of Mercury(II) Using Gold Ultra‐Microelectrode Arrays

The electroanalytical detection of trace mercury(II) at gold ultra‐microelectrode arrays is reported. The arrays consist of 256 gold microelectrodes of 5 μm in diameter in cubic arrangements which are separated from their nearest neighbor by 100 μm. The array was utilized in nitric acid using linear sweep voltammetry where a linear response from mercury additions over the range 10 μg L^?1?200 μg L^?1 (10^?8?10^?6 M) was observed with a sensitivity and detection limit of 0.11 nC/μg L^?1 and 3.2 μg L^?1 (16 nM) respectively from using a deposition time of 30 s at ?0.2 V (vs. SCE). This methodology was explored in 0.1 and 1 M chloride media over the mercury range 10 μg L^?1?200 μg L^?1 (5×10^?8?10^?6 M) where similar sensitivities of 0.087 nC/μg L^?1 and 0.078 nC/μg L^?1 were observed with an identical detection limit. The protocol is demonstrated to be useful for the determination of mercury for analysis of environmental water samples.     

Influence of desorption and sorption of water on the purity of perfluorooctanoic acid

The composition of impurities in perfluorooctanoic acid (PFOA) was measured and determined to be notably different between lots. Since the purity of PFOA varied, the accuracy of prepared calibration solution concentrations was reduced. In this study, factors influencing the purity were investigated using a Karl Fischer titrator and a LC/MS to support the development of reference materials. The results showed variances of water and isomer/homologue contents under different ambient conditions during sample handling. Moreover, these variances, especially for water, greatly affected the purity of PFOA (0.95–0.99 kg kg^?1). Therefore, PFOA of reliable purity should be used for the preparation of calibration solutions.