痕量硒的催化褪色法测定

研究了在盐酸介质中，以EDTA作掩蔽剂，痕量硒(Ⅳ)强化催化氯酸钾氧化2-(5-硝基-2-吡啶偶氮)-5-二乙氨基苯酚（5-NO2-PADAP）褪色反应及其动力学条件，建立了催化动力学测定痕量硒的新方法。方法检出限为0.0183цg/L Se(Ⅳ)，该法用于测定人发中痕量硒，结果令人满意。     

超支化聚合物分离富集催化光度法测定痕量硒

研究了超支化聚合物在硝酸介质中分离富集硒,吸附的容量大,选择性高,无污染。同时研究了分离后硒在硝酸介质中,痕量硒(Ⅳ)催化溴酸钾氧化2',4'-二氯苯基荧光酮褪色的指示反应及其动力学条件,据此建立测定痕量硒(Ⅳ)的新方法,方法的检出限为4.21×108g·L1,测定范围为0-0.6μg/10mL,用于样品的测定获得满意结果。     

高碘酸钾氧化中性红褪色催化动力学光度法测定痕量硒(Ⅳ)

基于3.2×10-4mol/LH2SO4介质中,痕量硒(Ⅳ)催化KIO4氧化中性红的褪色反应,建立了测定痕量硒(Ⅳ)的动力学光度法。在固定加热时间段(6min)后,于530nm处测定中性红的吸光度降低值监控反应速率。方法检出限为0.36μg/L,校准曲线的质量浓度线性范围为0～8.0μg/L。实验了酸度、反应物浓度、温度、反应时间、干扰离子等因素的影响。研究了反应的最佳条件,并测定了一些动力学参数,催化反应的表观活化能为81.60kJ/mol。11次重复测定0.1μg/25mL和0.2μg/25mLSe(Ⅳ)的相对标准偏差分别为2.1%和1.9%。方法用于食品和人发样品中痕量硒(Ⅳ)的测定,相对标准偏差为0.33%～3.8%,加标回收率为96.0%～103.0%。     

催化褪色光度法测定海洋生物中痕量硒

在pH =3的HCl KHC8H4O4缓冲介质中 ,硒 能催化溴酸钾氧化甲基紫的褪色反应 ,据此建立了催化动力学光度测定痕量硒的新方法。优化了动力学反应条件 ,并对海洋生物样品测定的前处理过程进行了研究。该方法对硒的检出限为 0 .14μg L ,线性范围为 0～ 8μg L ,精密度和准确度良好 ,对牡蛎等海洋生物样品中总硒含量测定的RSD <10 %,回收率为 96 %～ 10 7%,与DAN荧光光度法测定结果的相对偏差 <± 6 %。     

邻苯二酚紫体系催化动力学光度法测定痕量锡(Ⅱ)

基于痕量锡在0.5 mol/L的H2SO4介质中对溴酸钾氧化邻苯二酚紫的褪色反应具有催化作用,建立了一种新的测定痕量锡的催化动力学光度法.确定了该褪色反应的最佳条件:0.5 mol/L H2SO4 1.5 mL;0.1 mol/L KBrO3 1.3 mL;2.0×10-4 mol/L邻苯二酚紫3.5 mL;反应时间为7 min;反应温度为100℃.方法的检出限为4.51×10-3 μg/mL,线性范围为0～3 μg/25 mL.对该方法进行了精密度测定,其相对标准偏差为1.9%.研究了反应的动力学参数,确定了催化反应的的速率方程和表现活化能(Ea=34.10 kJ/mol).该方法可用于水样、人发中痕量锡的测定,相对标准偏差分别为0.32%和1.2%,标准加入回收率分别为99.2%和99.1%.     

丁基罗丹明B-高碘酸钾动力学光度法测定铑

报道了以铐催化高碘酸钾氧化丁基罗丹明B为基础的动力学测定痕量铑的方法,详细研究了动力学条件,建立了动力学光度测定痕量铑的新方法,铑浓度在0～180μg/L范围内与log(A_o/A)呈线性关系,检出限为2.84×10~(-7)g/L,该反应对Rh(Ⅲ)或丁基罗丹明B为一级反应,表观活化能为64.04kJ/mol.本方法用于某些催化剂中铑的测定,其相对标准偏差为1.76%～3.46%,回收率为96.8%～104.7%.     

阻抑动力学光度法测定白鼠肝脏中的超痕量镍(Ⅱ)

在 NH3- H2 O- NH4 Cl介质中 ,超痕量镍 ( )能阻抑 H2 O2 氧化甲基紫褪色的指示反应 ,研究了阻抑褪色反应的最佳条件和动力学参数 ,建立了测定超痕量镍 ( )的新方法。方法检出限为 4.4× 1 0 -11g/m L Ni( ) ,测定范围为 0～1 .0μg/2 5m L。方法已用于测定生物样品中的 Ni( )。     

催化动力学光度法测定痕量钌(III)

催化动力学光度法测定痕量钌(III)近年来有一些报道[1～3].这些方法均以催化褪色反应为指示反应,而以催化显色反应为基础的方法尚未见报道.我们发现,在磷酸介质中,Ru(III)对KIO4氧化二安替比林邻溴苯基甲烷(DAoBM)的显色反应有明显的催化增色作用.由此建立了测定痕量钌的催化分光光度法,并且测定了一些动力学参数.该法测定钌的线性范围是0～12μg/L,检测限为2.9×10-7g/L.     

阻抑动力学光度法测定水样中的痕量铋

基于弱酸介质中, 在十二烷基磺酸钠(SDS)存在下, 痕量Bi3 对H2O2氧化结晶紫(CV)的褪色反应有明显的阻抑作用, 建立了测定痕量Bi3 的阻抑动力学光度法, 研究了该反应的最佳实验条件和动力学参数. 结果表明, 该方法检出限为2.77×10-8 g/L, 线性范围为0～0.008 μg/mL. 可用于环境水样中铋的测定.     

考马斯亮蓝G动力学光度法测定痕量铁的研究

研究了在稀盐酸介质中 ,α,α-联吡啶存在下 ,铁催化溴酸钾氧化考马斯亮蓝G,使其褪色这一新的指示反应及其动力学条件 ,建立了测定痕量铁的新方法。方法的检出限为 2 .2 6× 1 0 - 10 g/ m L,线性范围 0～ 0 .2 4μg/ 2 5 m L,用于食品及水中痕量铁的测定 ,结果满意     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。