巨磁阻抗效应实验研究

利用物理实验室中常见的设备,搭建了一组巨磁阻抗效应实验装置,测量了在不同轴向外磁场及不同频率下钴基非晶态软磁合金细丝的阻抗.阻抗实部虚部均随外磁场增大迅速减小,而随频率增大缓慢增大.与交流阻抗的电磁理论比较,该实验结果与理论一致.实验观察到在40 MHz的频率、10 mT外磁场中阻抗变化达80%.根据数据和理论公式拟合,发现材料复磁导率随磁场强度增大迅速减小.     

钴基非晶丝的巨磁阻抗效应实验装置设计

介绍了巨磁阻抗效应的原理,提出了测量方法,分析巨磁阻抗效应随频率、外加磁场的变化规律.研究表明在6~21 MHz范围内,100 mT磁场下巨磁阻抗可达-50%以上,并且在30~40 mT磁场下巨磁阻抗即可达到-40%.     

复合结构丝中的电流密度分布和巨磁阻抗效应

提出了由中间为高电导率的非铁磁性金属丝外面包裹一层铁磁材料组成的复合结构丝的电流 密度分布和巨磁阻抗(GMI)效应模型，并对Cu/FeCoNi复合丝进行了数值模拟. 结果表明：在 相同的磁性材料几何尺寸和磁特性时，Cu/FeCoNi复合丝铁磁层内的电流随频率的升高比匀 质FeCoNi铁磁丝内的电流更趋于表面分布，而且开始出现趋肤效应时对应的频率明显降低. 当在比较低的频率下就可以观察到明显的MI变化时，复合结构丝中的电阻和电抗变化主要是 由趋肤效应引起，趋肤效应仍然是引起复合结构材料(包括多层薄膜结构) 关键词： 电流密度 巨磁阻抗效应 趋肤效应     

LC共振型巨磁阻抗效应的研究

采用化学镀方法成功制备了自带电容构成LC共振回路的CoP/Insulator/BeCu复合结构丝. 研究了这种新型复合结构丝产生LC共振型巨磁阻抗效应的特征,长度为l_m=95 cm的复合结构丝,当驱动电流频率为LC共振频率f_r=290 MHz时,LC共振型巨磁阻抗效应为4875%,磁场灵敏度为046%/A·m^-1,大于常规复合结构丝;远离此频率时的巨 关键词： 复合结构丝 LC共振')" href="#">LC共振 等效电路模型 巨磁阻抗效应     

交流电流对铁基纳米晶丝巨磁阻抗效应形貌的影响

本文研究了交流电流的大小(I ＝0.2—20 mA)和频率(f ＝ 1—1 MHz)对具有横向畴结构的铁基纳米晶丝的巨磁阻抗效应形貌的影响.实验结果表明,样品的巨磁阻抗效应呈双峰特征,随着频率的增大,双峰的位置H=±H_m向高场移动;但随着电流的增大,双峰的位置逐渐向中心(H ＝ 0)收缩,甚至变成单峰位形.理论上一般认为,双峰的位置与横向各向异性场H_k相对应,即H< 关键词： 巨磁阻抗效应 交流电流 铁基纳米晶丝     

NiFeCoP/BeCu复合结构丝的巨磁阻抗效应和磁化频率特性

用化学镀的方法制备了NiFeCoP/CuBe复合结构丝，研究了其巨磁阻抗特性.结果表明复合结构丝在较低频率的驱动电流下就有明显的磁阻抗效应，当驱动电流频率在20kHz时的磁阻抗效应为40％，最大磁阻抗效应出现的频率在180kHz，为97％.利用复数磁导率和等效电路探讨了该复合丝铁磁层磁化过程的频率特性，复合结构丝的特征弛豫频率在1MHz左右.外加直流磁场抑制畴壁移动，在等效电路中与抵消部分并联电路相关. 关键词： 巨磁阻抗效应 磁导率 弛豫频率 等效电路     

新一类磁传感效应——巨磁阻抗效应

材料的交流阻抗随外加直流磁的改变而变化的特性称为磁阻抗效应，在软磁合金中，这种效应是快响应，高灵敏度的，因而被称为巨磁阻抗效应，文章简单介绍了这一效应产生的基本原理、高频和低频交流电流情况下这一效应的特点，介绍了这一效应的应用前景。     

射频溅射功率对FeZrBCu软磁合金薄膜巨磁阻抗效应的影响

用射频溅射法制备了FeZrBCu软磁合金薄膜.研究了不同溅射功率对FeZrBCu薄膜软磁特性和巨磁阻抗效应的影响.用电子探针显微镜测量发现，当溅射功率为240W时，薄膜样品中Fe的原子含量为8732%，Cu的原子含量为29%.这种样品的矫顽力最小，为68A/m，饱和磁化强度约为111×105⁵A/m，软磁性能最佳，巨磁阻抗效应最大，溅态膜在 13MHz最大巨磁阻抗比纵向为17%，横向为11%.重点分析了阻抗的电阻、电感分量及横向有 效磁导率随频率的变化，得到在低频下主要是磁电感 关键词： 铁基合金 薄膜 巨磁阻抗效应     

磁场退火对Co基熔体抽拉丝巨磁阻抗效应的影响

对Co基熔体抽拉非晶丝进行了普通炉内退火和不同磁场强度（500 Oe,1600 Oe,4000 Oe）下的横向和纵向磁场退火,利用HP4192阻抗分析仪和Lakeshore7407VSM分析了退火态样品的巨磁阻抗（GMI）效应和软磁性能.研究结果表明,纵向磁场降低了环向各向异性,纵向磁场退火样品GMI效应降低且GMI曲线为单峰,最大阻抗变化率ΔZ/Z为131%,磁场响应灵敏度为7%/Oe;而横向磁场提高了环向畴体积,增加了环向各向异性场,导致退火样品GMI曲线随频率升高由单峰转 关键词： 非晶丝 巨磁阻抗效应 退火     

FeCuCrVSiB单层和多层膜的横向巨磁阻抗效应

用射频溅射法制备了Fe_71.5Cu₁Cr_2.5V₄Si₁₂B₉单层膜和结构为(F/S)₃/M/(F/S)₃的多层膜，在制备过程中加72kA/m的纵向磁场.研究表明在制备过程中加磁场明显改善了材料的软磁性能，降低了材料的矫顽力.将样品经不同温度退火热处理后，发现经230℃退火1.5h的单层膜和多层膜具有最佳的软磁性能和最大的磁阻抗效应，单层膜最大横向磁阻抗比为37.5%，多层膜最大横向磁阻抗比高达277%.通过比较单层和多层膜磁阻抗效应随频率和磁场的变化，发现多层膜具有较低的磁阻抗效应的临界频率和峰值特征频率，和较大的磁阻抗变化率，而且有较低的横向磁阻抗效应的饱和场. 关键词： 铁基合金 多层膜 巨磁阻抗效应     

CoFeSiB非晶丝弱磁场测量仪的研制

设计了以Co基非晶丝为敏感元件的传感器探头,多谐振荡励磁电路,信号处理电路,单片机显示电路,且对该磁场测量仪进行了标定。     

Physical properties and giant magnetoimpedance sensitivity of rapidly solidified magnetic microwires

The relation between the magnetoimpedance and the magnetic properties of a wide set of soft magnetic microwires from several sources has been studied. Magnetic properties were obtained by vibrating sample magnetometry and ferromagnetic resonance spectroscopy. The magnetoimpedance voltage sensitivity of each sample, the criterion of interest for high sensitivity magnetometer design, was then evaluated at several frequencies and drive currents. It appears that all samples possess roughly similar properties, regardless of their fabrication process or chemical composition. The voltage sensitivity of the samples obtained from experimental measurement is compared with a simple model of sensitivity. The general trends predicted by the model provide useful insights for materials optimization. Averaged sensitivity over the sample set is around 10 kV/T/cm at 10 MHz. The critical importance for sensitive magnetometry of the maximum excitation current permissible in each wire is also highlighted.     

斜位电流注入磁共振电阻抗成像（MREIT）与硬件设计

现有的磁共振电阻抗成像(MREIT)方法只适用于主磁场平行水平面的磁共振系统,本文中提出了一种新的MREIT方法即斜位电流注入磁共振电阻抗成像,同时适用于主磁场垂直于水平面的磁共振系统. 硬件系统以磁共振主控计算机为控制中心,将MRI与EIT有机结合于一体：(1)能够测量注入电流在成像体内部感应磁场的磁感应强度B(x,y,z);(2)向成像体注入电流;(3)满足时序匹配要求;(4)测量边界电压. 文章还展示了利用此装置所得的初步实验结果.     

Studies of magnetic properties of permalloy (Fe-30%Ni) prepared by SLM technology

In the present study, a high permeability induction Fe-30%Ni alloy cubic bulk was prepared by the selective laser melting process. In order to reveal the microstructure effect on soft magnetic properties, the microstructure and magnetic properties of the Fe-30%Ni alloy were carefully investigated by scanning electron microscopy, X-ray diffraction and hysteresis measurements. The bcc-Fe (Ni) phase formation is identified by X-ray diffraction. Meanwhile, it was found that low bcc lattice parameter and high grain size could be obtained when high laser scanning velocity and low laser power were used. Moreover, the lowest value of coercivity is 88 A/m, and the highest value of saturation magnetization is 565 Am²/kg, which can be obtained at a low laser scanning velocity of 0.4 m/s and high laser power input at 110 W.     

Influence of the distance between two voltage contacts on giant magneto-impedance of Co-based amorphous wires

The Co₇₅ Fe_4.2Si₈B₁₂Nb_0.8 amorphous wires of 30 μ m in diameter are produced by melt extraction and annealing at 450 oC for 20 min in vacuum with a longitudinal or transverse field of 40 kA/m. Distances between the two voltage contacts of 6, 5, 4 and 2 mm are obtained by moving the two voltage contacts towards the centre of the sample at the same time. Results indicate that magneto-impedance response is dependent on the distance significantly. As distance decreases from 6 to 2 mm, △Z/Z reduces from 609% to 95% and giant magneto-impedance (GMI) profiles change from two-peak to single-peak. Besides, field sensitivity improves from 0.47%/(A/m) to 0.76%/(A/m) when the single-peak GMI just appears. It is therefore concluded that actual measurements can be made comparable only by taking into account the influence of distance between two voltage contacts for a magneto-impedance measurement.     

Magnetic and Gas Sensing Property of Nanosized NiFe2O4 Powders Synthesized by Pulsed Wire Discharge

Nickel ferrite (NiFe₂O₄) powders were synthesized by pulsed wire discharge method. X-ray diffraction (XRD) and transmission electron microscopy (TEM) analyses show that only nickel ferrite spinel and no other phase was observed in the powders. Mean size of the obtained particles strongly depended on the oxygen pressure: the higher oxygen pressure corresponds to larger powder size, as determined by Brunauer–Emmet–Teller (BET). The room temperature saturation magnetization of the synthesized powders was 42–46 emu/g depending on the powder size. These powders also showed high chlorine sensitivity at about 280–360°C, and a good linear sensitivity with chlorine concentration.     

The Analysis of Large Barkhausen Effect in the FeSiB Amorphous Wire

Amorphous FeSiB wires with positive magnetostriction are very perspective soft magnetic materials for many applications, e.g. torque, field or current sensors, pulse generators and highly sensitive magnetometers. The appearance of the Large Barkhausen Effect (LBE) during slow magnetization of FeSiB wires is described by means of the core-shell model assuming a residual radial tensile stresses in the as-cast state. In this work, the LBE during magnetization reversal of Fe_77.5Si_7.5B₁₅ amorphous wire in the as-cast state was analysed. We have studied the kinetics of the reverse domain in the core region of the wire by means of Sixtus-Tonks method of two small pick-up coils placed in an asymmetric way with respect to the ends of the wire. We estimated the velocity of the reverse domain wall and the core region volume of the wire. It was found that the residual radial tensile stress distribution of the shell region strongly influences the magnetization reversal in the FeSiB wire.     

Validity and Limitation of Semi-Classical Approaches to Giant Magnetoresistance in Magnetic Multilayers

The validity and limitation of semi-classical theories on giant magnetoresistance in magnetic multilayers are discussed on the basis of fundamental quantum statistical mechanics.     

电子在圆柱形半导体量子线中的行为研究

用计算一维势阱波函数的方法简化了圆柱形量子线波函数的计算, 得出了量子线中电子的能态、 能级图和波函数。 在确定温度条件下, 讨论了量子线的线宽与它的光谱蓝移、 能级分离或兼并以及电子能态的关系。The wave function of column quantum wires has been calculated with the means of calculation for the quantum wave function in one dimensional potential well. The energy state, energy level diagram and wave function of column quantum wire have gained. Under assured temperature, the relations of column quantum wire diameter to its spectrum blue shift, separation or annexation of energy level, and electrons energy state have been discussed.