应用二维频移LDV测量多孔板管流的湍流特性

采用二维ＬＤＶ系统对圆管中装有四孔板和三孔板的湍流特性进行了实验研究．在孔板下游射流沿管轴逐渐混合．沿管壁可以观察到反向流区域．经足够长距离后，轴向和切向湍流度逐渐趋于相同数量级．实验结果表明，孔板结构和开孔度对湍流特性有重要影响．     

Vibro-Acoustic Response of a Pipe Excited by a Turbulent Internal Flow

This article presents an experimental study of the vibro-acoustic response of a pipe excited by a fully-developed turbulent air flow. First, the wall pressure field acting on the internal pipe wall is investigated. The power spectral density of the wall pressure fluctuations is analyzed after cancellation of contaminating background noise. The convection velocity and correlation lengths are calculated from measured cross-spectra, and the cross-spectra are expressed in Corcos model form. Second, the vibro-acoustic response of the pipe is analyzed by referring to the structural modes of the pipe. This revised version was published online in July 2006 with corrections to the Cover Date.     

Experiments in Turbulent Pipe Flow with Polymer Additives at Maximum Drag Reduction

In this paper we report on (two-component) LDV experiments in a fully developed turbulent pipe flow with a drag-reducing polymer (partially hydrolyzed polyacrylamide) dissolved in water. The Reynolds number based on the mean velocity, the pipe diameter and the local viscosity at the wall is approximately 10000. We have used polymer solutions with three different concentrations which have been chosen such that maximum drag reduction occurs. The amount of drag reduction found is 60–70%. Our experimental results are compared with results obtained with water and with a very dilute solution which exhibits only a small amount of drag reduction. We have focused on the observation of turbulence statistics (mean velocities and turbulence intensities) and on the various contributions to the total shear stress. The latter consists of a turbulent, a solvent (viscous) and a polymeric part. The polymers are found to contribute significantly to the total stress. With respect to the mean velocity profile we find a thickening of the buffer layer and an increase in the slope of the logarithmic profile. With respect to the turbulence statistics we find for the streamwise velocity fluctuations an increase of the root mean square at low polymer concentration but a return to values comparable to those for water at higher concentrations. The root mean square of the normal velocity fluctuations shows a strong decrease. Also the Reynolds (turbulent) shear stress and the correlation coefficient between the stream wise and the normal components are drastically reduced over the entire pipe diameter. In all cases the Reynolds stress stays definitely non-zero at maximum drag reduction. The consequence of the drop of the Reynolds stress is a large polymer stress, which can be 60% of the total stress. The kinetic-energy balance of the mean flow shows a large transfer of energy directly to the polymers instead of the route by turbulence. The kinetic energy of the turbulence suggests a possibly negative polymeric dissipation of turbulent energy. This revised version was published online in July 2006 with corrections to the Cover Date.     

Reynolds Number Dependence of Velocity Structure Functions in a Turbulent Pipe Flow

Low-order moments of the increments δu andδv where u and v are the axial and radial velocity fluctuations respectively, have been obtained using single and X-hot wires mainly on the axis of a fully developed pipe flow for different values of the Taylor microscale Reynolds numberR _λ. The mean energy dissipation rate〉ε〈 was inferred from the uspectrum after the latter was corrected for the spatial resolution of the hot-wire probes. The corrected Kolmogorov-normalized second-order structure functions show a continuous evolution withR _λ. In particular, the scaling exponentζ _v , corresponding to the v structure function, continues to increase with R _λ in contrast to the nearly unchanged value of ζ _u . The Kolmogorov constant for δu shows a smaller rate of increase with R _λ than that forδv. The level of agreement with local isotropy is examined in the context of the competing influences ofR _λ and the mean shear. There is close but not perfect agreement between the present results on the pipe axis and those on the centreline of a fully developed channel flow. This revised version was published online in July 2006 with corrections to the Cover Date.     

Invariant Analysis of Turbulent Pipe Flow

The anisotropy analysis of Lumley provides a useful tool to quantify the degree of anisotropy in turbulent flows. Also included in the analysis are relations which may be used to check if the flow is axisymmetric or two-dimensional. However, the method does not provide any scale information about the structures. The analysis has therefore been extended here to Fourier space, which allows scale information to be derived. The method was applied to fully developed pipe flow and it was shown that the large-scale motion is everywhere close to axisymmetric. The intermediate scales are strongly influenced by the restrictions posed by the pipe walls. At the centre line, the flow structure appears axisymmetric at all scales, but the measurement sindicate that true axisymmetry is lost very quickly away from the centre line. The structure of the smallest scales could not be determined reliably due to a singularity in the analysis which develops as the scales go to zero. This revised version was published online in July 2006 with corrections to the Cover Date.     

Velocity profile measurement by ultrasonic doppler method

The ultrasonic velocity profile measuring method has been developed at PSI for application in fluid mechanics and fluid flow measurement. It uses pulsed ultrasonic echography together with the detection of the instantaneous Doppler shift frequency. This method has the following advantages over the conventional techniques: (1) an efficient flow mapping process, (2) applicability to opaque liquids, and (3) a record of the spatiotemporal velocity field. After a brief introduction of its principle, the characteristics and specifications of the present system are given. Then examples in fluid engineering for oscillating pipe flow, T-branching flow of mercury, and recirculating flow in a square cavity are described that confirm the method's advantages. Several other works under way by other investigators are introduced. A potential for in-depth study of fluid dynamics is demonstrated by several examples from an investigation of modulated wavy flows in a rotating Couette system. The position-averaged power spectrum and the time-averaged energy spectral density were used to study the dynamic characteristics of the flow, and subsequently the velocity field was decomposed into its intrinsic wave structure based on two-dimensional Fourier analysis.     

Experimental Determination of Lagrangian Velocity Statistics in Turbulent Pipe Flow

The calculation of Lagrangian statistics out of experimentally determined data from homogeneously seeded inhomogeneous turbulent flows is far from straightforward since statistical properties are position-dependent, necessitating local sampling. Two solutions for the preferential sampling of faster particles at a certain position in the flow are proposed. The performance of both methods was tested using DNS calculations for turbulent pipe flow. Both methods show a good performance for various statistical properties, thus providing two reliable ways to analyze experimental data from inhomogeneous turbulent flows.     

湍流管径问题算法的改进

本文采服无量纲参数（ｇＪＯ＾３／ｖ＾５）及ＫｓＶ／Ｑ）由最小二乘法以指数函数拟合Ｐｒａｎｄｔｌ及Ｋａｒｍａｎ公式，得出分别适用于光滑区和粗糙区的管径算式。再对以上两式作粘性关联偶合，得出适用于湍流过渡区的管径算式。可直接求出管径，避免繁复试算和迭代。计算结果与Ｐｒａｎｄｔｌ，Ｋａｒｍａｎ及Ｃｏｌｅｌｒｏｏｋ－Ｗｈｉｔｅ等经典公式能精确吻合，较Ｓｗａｍｅｅ－Ｊａｉｎ湍流管径算式误差减少一半以上。     

Effect of the Streamwise Component of the Vorticity Formed in a Turbulent Jet Source on the Acoustic Characteristics of the Jet

The results of an experimental study of the effects of different nozzle heads on turbulent jet noise are analyzed. A configuration of four cylindrical heads, tabbed heads, and chevron nozzles are considered and the decreases in the acoustic-mechanical efficiency of the jet (acoustic power reduction) for jets exposed to different modes of action are compared.It is shown that the effects of tabbed and cylindrical heads, as well as of chevrons, share a common property which is associated with the occurrence of vorticity in the jet source and can be described on the basis of a unified criterion characterizing the action on both the jet flow structure and the jet noise.     

Steady Streamwise Structures in the Boundary Layer on a Swept Wing with Elevated Turbulence of the Incoming Flow

Results for a turbulized flow past the windward side of a swept wing model are presented. Origination of steady disturbances in the form of streamwise structures is found. The greatest effect on the formation of these disturbances is exerted by the curvature of the external flow streamlines. The secondary flow in the boundary layer leads to an increase in the characteristic scale of disturbances in the transverse direction, as compared to the flow around the model at a zero yaw angle.     

Interaction of a Streamwise Vortex with an Oblique Shock Wave

Interaction of a supersonic streamwise vortex with an oblique shock wave is considered. A mathematical model of the streamwise vortex is constructed. Three interaction regimes (weak, moderate, and strong) are found. It is shown numerically that vortex breakdown is possible in the case of strong interaction. The influence of the governing parameters on the interaction type is studied. It is shown that the main effect on the interaction type is exerted by the streamwise velocity and angle of the wedge forming the shock wave. The effect of splitting of the primary vortex on the shock wave in the case of moderate and strong interaction regimes is found.     

网栅后湍流流动沿流程衰减特性的实验研究

应用ＬＤＶ测试技术对垂直方管内三种不同栅距的网所形成的湍流流动做了详细测量,网栅栅距Ｍ分别为１４ｍｍ,１０ｍｍ,６ｍｍ实验给出了管内不同位置湍流流动的各种参数沿流动方向的衰减规律,并就三种网栅进行比较分析,以探讨这种网栅流动所具有共同规律和在不同栅距对湍流结构及脉动大小的不同特点,从而对这种网栅所形成的湍流流结构较为清晰的了解。     

On the Electric Potential Induced by a Homogeneous Magnetic Field in a Turbulent Pipe Flow

In this paper we study a turbulent pipe flow of a weakly electrical conducting fluid subjected to a homogeneous magnetic field which is applied perpendicular to the flow. This configuration forms the basis of a so-called electromagnetic induction flow meter. When the Hartmann number is small so that modification of flow by the Lorenz force can be neglected, the influence of the magnetic field results only in a spatially and temporally varying electric potential. The magnitude of the potential difference across the pipe is then proportional to the flow rate and this constitutes the principle of the flow meter. In this study the flow and electric potential are computed with help of a numerical flow simulation called Large-Eddy Simulation (LES) to which we have added an equation for the electrical potential. The results of the LES have been compared with experiments in which the electric potential is measured as a function of time at several positions on the circumference of the pipe. Both the experimental and numerical results for the mean potential at the pipe wall agree very well with an exact solution that can be obtained in this particular case of a homogeneous magnetic field. Furthermore, it is found that fluctuations in the electric potential due to the turbulence, are small compared to the velocity fluctuations. Based on the results we conclude that electrical-magnetic effects in pipe flow can be accurately computed with LES.     

基于PIV测量的超声波流量计内流场特性研究

采用PIV(Particle Image Velocimetry)测量手段,考察了小口径超声波流量计的流动特性。首先针对前端安装直管段时,不同流量条件下的流场特性建立基本认识,实验结果表明,在低流量条件下,流量计内流场存在明显的不稳定演变和非定常流动特征。进一步以上游前端安装球阀为典型案例,考察了安装条件对超声波流量计响应特性和测量偏差的影响。结合直管段的实验观测结果,发现此种结构超声波流量计的适应性与其流场非定常性的关系具有很好的一致性,即流场结构稳定则适应性强。此外,综合多参数的实验结果表明,雷诺数是判断小口径超声波流量计测量准确性的重要无量纲参数。     

蜗壳内紊流流场的有限元法计算

用有限元法计算径流式叶轮机械蜗壳的紊流时均流场.有关紊流模型采用K-ε两方程模型,用关于压力p的罚函数方法求解.所得结果可供分析蜗壳流场用.文中方法也可用于计算其他形状的二维通道流动.     

Permissible Height of the Surface Roughness in a Turbulent Boundary Layer with a Streamwise Pressure Gradient

The results of an experimental investigation of the effect of the streamwise pressure gradient in a turbulent boundary layer on the permissible height of the surface roughness of bodies in an incompressible fluid flow are presented. The permissible roughness Reynolds number for which the characteristics of the turbulent boundary layer remain the same as in the case of flow past a smooth surface is determined.     

On the Lower Critical Reynolds Number for Flow in a Circular Pipe

Flow in a circular pipe is investigated experimentally at Reynolds numbers higher than that at which the resistance coefficients calculated from the Blasius formula for laminar flow and from the Prandtl formula for turbulent flow are equal. The corresponding Reynolds number based on the mean-flow velocity and the pipe diameter is about 1000. The experiments were performed at a high level of inlet pulsations produced by feeding gas into the pipe through a hole with a diameter several times smaller than the pipe diameter. In our experiments the critical Reynolds number was determined as the value, independent of the distance from the inlet, at which the ratio of the axial to the mean-flow velocity as a function of the Reynolds number deviated from 2. At the maximum ratio of the pipe cross-sectional area to the area of the hole through which the gas entered the pipe, equal to 26, the critical Reynolds number was about 2300. After a fivefold increase in the hole area the critical Reynolds number increased by approximately 4%.At Reynolds numbers below 2000, after at a high level of the inlet pulsations an almost laminar flow had developed in the pipe, a perturbation was introduced by inserting a diametrically oriented cylindrical rod with a diameter 10–20 times smaller than the pipe diameter. In these experiments, at Reynolds numbers higher than 1000, at a distance from the rod equal to 50 pipe diameters the axial to mean-flow velocity ratio was less than 2, approaching this value again at large distances from the rod. The insertion of the rod led to a decrease in the critical Reynolds number by approximately 12%.     

管流系统的可控扰动装置及其应用

阐述了具有可控人工扰动装置的低背景湍动液体管流系统的研制和评价要点在及在高分子减阻液研究中的应用，并指出了这种实验系统在液体内流研究中的重要意义。     

The Use of DNS to Define Stress Producing Events for Turbulent Flow over a Smooth Wall

Over the past 15 years direct numerical simulations (DNS) of turbulent flow and particle image velocimetry (PIV) have provided the opportunity to obtain information about a turbulent velocity field simultaneously at a large number of locations. This paper gives a personal viewpoint of how these techniques are providing new insights about the Reynolds stress producing structures in turbulence generated by flow over a smooth boundary. This revised version was published online in August 2006 with corrections to the Cover Date.     

离心泵叶轮内宾汉流体湍流流场的数值计算

考虑宾汉流体本构关系特点,建立了任意曲线坐标系（ζ,η）下宾汉流体湍流流动的基本方程,应用压力加权校正算法,实现了速度场和压力场的关联,采用交错网格技术,解决了非物理压力振荡问题,在此基础上,对离心泵叶轮内回转面上宾汉流体湍流流动进行了数值模拟,并分析探讨了离心泵叶轮内宾汉流体湍流流动机理。