不同掺杂量对水热合成Zn1-xNix O稀磁半导体粉体的影响

本文主要考虑不同掺杂量对水热合成Zn1-xNixO稀磁半导体粉体的影响.采用水热法,以3 mol/L NaOH作为矿化剂,在240℃下,保温24 h左右,进行Ni掺杂(x=0.05,0.1,0.2),合成Zn1-xNixO稀磁半导体晶体.XRD、FE-SEM测试表征晶体的物相组成和晶体形貌,XRD表明所制备的zn0.95Ni0.05O稀磁半导体晶体发育比较完整.通过UV-vis测试进一步说明掺杂的效果.VSM测试表明,所制备的样品在室温下有良好的磁滞回线,表现出铁磁性.     

Fe、Ni掺杂ZnO纳米棒的水热法制备与磁性能研究

采用水热法制备稀磁半导体材料,样品Zn0.95 Fe0.05O和Zn0.95Fe0.03Ni0.02O的XRD图谱和TEM图谱发现,样品具有纤锌矿结构,形貌为纳米棒状结构.XEDS分析显示,掺杂的Fe和Ni元素进入到了ZnO晶体中.RAMAN光谱表明,Zn2+被Fe2+、Ni2+替换,晶体发生拉曼光谱红移.PL光谱分析发现,在室温条件下,随着Fe2+和Ni2+的掺杂,出现了猝灭现象.VSM测量显示,掺杂样品在室温条件下存在明显的铁磁性,且这种铁磁性属于稀磁半导体的内禀属性.实验结果表明在水热法条件下,获得了ZnO基稀磁半导体材料样品,且样品具有良好的光学和磁学特性,为进一步研究稀磁半导体材料提供了一定的参考.     

In和过渡金属离子共掺杂对ZnO晶体形貌的影响

采用水热法,KOH作矿化剂,在ZnO前驱物中添加适量的CoCl2·6H2O,FeCl2·4 H2O,NiCl2·6H2O,In2O3,其中Co:In:Zn,Fe:In:Zn,Ni:In:Zn 分别为5:1:100,5:1:100,3:1:100.3 mol/L KOH作矿化剂,温度430 ℃,填充度35;,反应24 h,制备了In和过渡族金属离子共掺的ZnO晶体.结果表明,掺杂In2O3时,所合成的过渡族金属离子掺杂的ZnO晶体均呈现六角片状晶体,晶体形貌规则,表面光滑,直径为5～10 μm.和未掺杂In的晶体相比,掺杂In后,晶体c轴极性生长速度得到明显的控制,a、b轴方向生长速度提高,大面积显露+c{0001}、负极面-c{0001}面,另外还显露正锥面+p{1011}、负锥面-p{101-1-}.     

水热法合成Zn1-xNixO稀磁半导体

本文采用水热法,在温度430℃,填充度35%,矿化剂为3mol/L KOH,前驱物为添加适量N iC l2.6H2O的Zn(OH)2,反应时间24h,合成了Zn1-xN ixO稀磁半导体晶体。当在Zn(OH)2中添加一定量的N iC l2.6H2O为前驱物,水热反应产物为掺杂N i的多种形态ZnO混合晶体,对其个体较大的晶体中进行电子探针测量表明,前驱物中的添加量和晶体中实际掺入量有很大的差异,只有少量的N i离子掺入ZnO,最大N i原子分数含量为0.62%。采用超导量子干涉磁强计测量材料的磁性,发现在室温以下,晶体的磁化强度不随温度升高而下降。在室温下,存在明显的磁饱和现象和磁滞回线,说明具有室温下的铁磁性。     

水热法合成Zn1-xCoxO室温稀磁半导体

本文采用水热法,在430℃,填充度为35;,3mol/L KOH作为矿化剂,反应时间为24h,合成了Zn1-xCoxO晶体.当在Zn(OH)2中添加一定量的CoCl2·6H2O为前驱物时,水热反应产物中,可以获得多晶体形态的掺杂Zn1-xCoxO晶体.电子探针测量表明,随着前驱物中CoCl2·6H2O添加量的增加,晶体中的Co实际掺入量也随着增加.采用超导量子干涉磁强仪测量材料的磁性,发现在室温以下,水热法合成的Zn1-xCoxO晶体的磁化强度随温度变化很小,在300K存在明显的磁饱和现象和磁滞回线,表明具有室温下铁磁性.     

高浓度Co掺杂ZnO晶体的水热法制备及磁性

采用水热法以CoO、ZnO混合为前驱物制备了ZnO晶体,矿化剂为6 mol/L KOH,填充度70;,温度430℃,两种样品CoO、ZnO组分物质的量百分比分别为0.5∶1和1∶1.当前驱物为nCo∶nZn=0.5∶1时,合成出Zn1-xCoxO晶体,Co元素掺杂量分别为6.83 at;和9.30 at;.当前驱物中nCo∶nZn=1∶1时,Zn1-xCoxO晶体中Co掺杂比例达到9.31 at;,同时伴有Co3O4生成,其中Zn掺杂比例达到14.59 at;,SEM显示,所制备的Zn1-xCoxO具有明显的ZnO晶体特征,形态完整,最大尺度约为50 μm.SQUID测量显示,生成物中Zn1-xCoxO晶体具有顺磁性,Zn1-xCoxO和Co3-xZnxO混合晶体也显示为顺磁性.     

不同矿化剂对水热法生长的ZnO晶体发光的影响

采用水热法,以3 mol/L KOH为矿化剂,填充度35%,温度430℃,前驱物Zn(OH)2,比较研究了三种矿化剂条件下合成晶体的形貌和发光性能。三种矿化剂条件分别为样品1,3 mol/L KOH;样品2,3 mol/L KOH,1 mol/LLiOH;样品3,3 mol/L KOH,CaO∶Zn(OH)2=2%(物质的量百分比)。添加适量比例的LiOH或CaO,合成了非极性生长的ZnO晶体,晶体c轴方向生长速度明显减小,所合成的晶体大面积显露正极面c{0001},同时显露负极面-c{0001}、正锥面p{101}、负锥面-p{10}和柱面m{100}。只添加KOH或辅助添加LiOH时,合成晶体的发光光谱中只有可见光谱,无紫外线带边跃迁发光谱,说明晶体缺陷发光中心较多。添加CaO时合成晶体的发光光谱中有较强的紫外带边跃迁发光,说明晶体缺陷发光中心减少。     

水热法合成Zn1-xMnxO稀磁半导体

本文采用水热法在430℃,以3mol%.L-1KOH作矿化剂,填充度为35%,反应时间24h,合成了Zn1-xMnxO稀磁半导体晶体。所合成晶体具有ZnO纤锌矿结构,晶面显露正极面{0001}、负极面{0001}、菱面{1011}及负菱面{1011}晶体高度为5~30μm,径高比约为2:1。X荧光能谱(EDS)显示Mn原子百分浓度为2.6%(x=0.026)。晶体呈现低温铁磁性,居里温度50K。     

水热法生长的Co、Sn共掺杂ZnO晶体厚膜的顺磁性

采用水热法,6 mol/L KOH作为矿化剂,按物质的量比0.02∶0.5∶1添加SnO2、CoCl2和ZnO作为前驱物,填充度70%,温度430℃,以常规水热法制备的纯ZnO晶片为籽晶([0002]方向),在ZnO籽晶片上制备出多元掺杂的ZnO厚膜。厚膜呈墨绿色,EDS测量显示Co和Zn元素的相对含量为7.47∶92.53。电学测量晶体膜层为n型导电类型,载流子浓度1.15×1020cm-3,电阻率1.94×10-3Ω.cm,迁移率27.8 cm2/V.s,SQUID测量表明厚膜为顺磁性。     

稀磁Zn1-xNixO纳米棒的水热法制备与磁性能研究

采用水热法成功制备了不同浓度的Zn1-xNixO(x =0,0.01,0.05,0.10,0.20)稀磁半导体材料,并利用X射线衍射(XRD)、透射电子显微镜(TEM)、选区电子衍射(SAED)、X射线能量色散分析(XEDS)、拉曼(Raman)光谱和振动样品磁强计(VSM)对其晶体结构、形貌、组成元素和磁学性能等进行表征,实验结果表明,本方法所制备的不同掺杂浓度的Zn1-xNixO稀磁半导体样品具有结晶良好的纤锌矿结构,没有杂峰出现,样品中的Ni2+全部进入ZnO晶格中替代了部分Zn2+的格点位置,生成单一相的Zn1-xNixO,样品形貌都为纳米棒状结构,分散性良好.Zn1-xNixO样品在室温条件下存在明显的铁磁性,饱和磁化强度都随着Ni2+掺杂量的增加而呈现出先增加后减小的趋势,同时样品的单个镍原子的磁矩是逐渐下降的.     

Crystal and molecular structures oftrans-dichloro-(ethylene) (4-methylpyridine)platinum(II) andtrans-dichloro(ethylene) (2,4,6-trimethylpyridine)platinum(II)

The crystal and molecular structures oftrans-[PtCl₂(C₂H₄)(4-MeC₅H₄N)] (I) andtrans-[PtCl₂(C₂H₄)(2,4,6-Me₃C₅H₂N)] (II) have been determined by single-crystal x-ray methods.I crystallizes in space groupP2₁/c witha= 4.991(1), b=21.658(3), c=10.675(3) Å, =110.17(2) °,Z=4;II is orthorhombic (Pbca) witha=10.295(6),b=12.393(8),c=20.370(10) Å,Z=8.Full-matrix least-squares refinements have given finalR factors of 0.053 (1520 reflections) forI and 0.042. (1412 reflections) forII. The intensities were recorded by counter methods, and only those reflections havingI>3(I) were used in the analyses.In both complexes, platinum is four-coordinate with the two chlorine atoms, the double bond of the ethylene, and the nitrogen atom of the substituted pyridine. The two structures are discussed in terms of the arrangement of the pyridine ligand with respect to the PtCl₂(C₂H₄) moiety.     

Synthesis, spectroscopy, and X-ray structures of fac-(CO)3(dppe)MnSC(S)H, fac-(CO)3(dppe)ReSC(S)H, fac-(CO)3(dppp)ReSC(S)H, and fac-(CO)3(dppb)ReSC(S)H

The monodentate dithioformato complexes, fac-(CO)₃(dppe)MnSC(S)H (1), fac- (CO)₃(dppe)ReSC(S)H (2), fac-(CO)₃(dppp)ReSC(S)H (3), and fac-(CO)₃ (dppb)ReSC(S)H (4), where dppe is 1,2-bis(diphenylphosphino)ethane, dppp is 1,3-bis(diphenylphosphino)propane, and dppb is 1,4-bis(diphenylphosphino)butane, were synthesized from the treatment of the corresponding hydrides, fac-(CO)₃ (P-P)MSC(S)H with CS₂. Compounds 1–4 crystallize in the monoclinic crystal system: for 1, space group = P2₁/c, a = 15.3139(3) Å, b = 9.7297(4) Å, c = 19.0991(6) Å, = 105.928(1), V = 2736.5 ų, Z = 4; for 2, space group = P2₁/c, a = 15.6395(8) Å, b = 9.8182(5) Å, c = 19.4153(11) Å, = 106.741(1), V = 2854.9(3) ų, Z = 4; for 3, space group = P2₁/n, a = 11.3570(10) Å, b = 19.465(2) Å, c = 15.5702(14) Å, = 104.776(2), V = 3328.3(5) ų, Z = 4; and for 4, space group = C2/c, a = 32.078(2) Å, b = 10.4741(6) Å, c = 19.0608(9) Å, = 94.315(2), V = 6386.1(6) ų, Z = 8.     

Structure of (chloranilato)bis(tri-n-butylphosphine)palladium(II)

(Chloranilato)bis(tri-n-butylphosphine)palladium(II), [Pd(C₆Cl₂O₄){P(C₄H₉)₃}₂] (chloranilic acid=2,5-dichloro-3,6-dihydroxy-p-benzoquinone): FW=718.02,P2₁/c,a=21.729(6),b=17.293(5),c=21.010(9) Å,=112.62(3)°,V=7287.42 ų,Z=8,D _c=1.309mg m^–3, Mo, =0.710730 Å,=0.76 mm^–1,F(000)=3008, finalR=0.087, 2594 observed reflections. Palladium is ligated by a distorted square planar P₂O₂ coordination sphere in the title compound. The two molecules per asymmetric unit differ in the arrangement of phosphine n-butyl chains, yielding two unique metal centers.     

Crystal structure of triphenylphosphine-(1-(di(trifluoromethyl)-hydroxymethyl)-cyclopentadienyl)-(1,2-di(carboxymethyl) ethylene-1-yl) ruthenium (0)

The structure of triphenylphosphine — (1 — (di(trifluoromethyl) — hydroxymethyl) — cyclopentadienyl) — (1,2 — di(carboxymethyl)ethylene — 1 — yl) — ruthenium (0) has been studied by single-crystal X-ray diffraction techniques. This compound, [C₅ H₄(CF₃)2 COH] Ru(PPh₃)C2(CO₂Me)₂H, crystallizes in the triclinic space groupP¯1 witha =10.131,b= 15.107,c= 10.798 Å, = 102.14, = 107.04, = 89.64° andZ = 2. The structure was refined by block-diagonal least-squares methods to a finalR value of 0.042, including hydrogen atoms. The compound contains a dicarboxymethylethylene ligand coordinated to ruthenium both through a ketonic oxygen and through a metal--carbon -bond. An intramolecular hydrogen bond is observed. Details of the structure are reported, and the structures of several Ru(0) complexes are compared.     

X-ray crystal structures ofcis-bis(diphenylphosphinamide)tetracarbonylmolybdenum(0) andtrans-bis(N-methyl diphenylphosphinamide)tetracarbonylmolybdenum(0)

The X-ray crystal structures ofcis-Mo(CO)₄(Ph₂PNH₂)₂,I, andtrans-Mo(CO)₄(Ph₂PNHMe)₂,II, are presented. ComplexI crystallizes in the monoclinic space groupP2₁/c(a=13.433(1),b=12.2719(8),c=17.318(2)Å;=109.79(1)°;V=2686.1(8)ų;Z=4). ComplexII crystallizes in the triclinic space groupP¯1 (a=6.9986(8),b=10.328(1),c=11.241(2)Å,=107.58(1)°,=91.76(1)°, =101.28(1)°,V=756.1(4)ų,Z=1). The molybdenum coordination geometry in each complex is a slightly distorted octahedron. The molybdenum-carbon bond lengths for the carbonyls trans to phosphorus in complexI are shorter than those the carbonyls trans to other carbonyls. The average molybdenum-phosphorus distance inI (2.525(5)Å) is similar to those in other diphenylphosphinamide complexes and longer than the molybdenum-phosphorus distance inII in 2.4585(7)Å). The distance between two nitrogen atoms incis Mo(CO)₄(Ph₂PNH₂)₂ (3.74(3)Å) is significantly larger than the sum of their van der Waals radii (3.10 Å) indicating that the two nitrogens are not hydrogen bonded.     

Structure of (N-(2-hydroxyphenyl)-salicylaldiminopiperidino) Ni(II) complex

The crystal and molecular structure of the title complex, C₁₈H₁₉N₂O₂Ni, has been determined by direct methods. The compound crystallizes in the monoclinic crystal system witha=22.973(1),b=5.212(1),c=27.076(1)Å, β=106.46(1)°, space groupC2/c,V=3109.1(6)ų, Z=8, andD _x=1.51g cm^?3. The nickel atom is in a slightly distorted square-planar environment of two oxygens [Ni(1)?O(1) 1.824(3) and Ni(1)?O(2) 1.856(3)Å] and two nitrogens [Ni(1)?N(1) 1.849(3) and Ni(1)?N(2) 1.932(3)Å] with O?Ni?N angles between 85.7(1) and 97.1(1)°. The nickel atom is 0.006 Å out of the plane of its ligands.     

Crystal and molecular structures of trans-bis(acetonitrile)bis(bipyridine)ruthenium(II) perchlorate and trans-diamminebis(bipyridine)ruthenium(II) perchlorate

The structures of trans-[(MeCN)₂(bpy)₂Ru](ClO₄)₂(I) andtrans-[(NH₃)₂(bpy)₂Ru](ClO₄)₂(II) have been determined by single crystal X-ray diffraction methods. (I) forms monoclinic crystals in the space groupP2₁/c witha=8.399(2),b=10.406(2),c=15.590(3) Å,=93.78(2)° andZ=2 atT=293 K. The final refinement gaveR=0.040 for 2448 reflections withF _o ² >3(F _o ² ). (II) crystallizes in the triclinic space groupP¯1 witha=1.702(1),b=8.439(2),c=10.525(2) Å,=107.56(2),=104.63(1), =100.89(2)° andZ=1 atT=293 K. Refinement using 1878 reflections withF _o ² >3(F _o ² ) produced a finalR value of 0.036. Both of these structures have the ruthenium atom located on a crystallographic inversion center. The bipyridine ligands in both structures are in the bowed conformation as a means of circumventing the steric problems associated with the trans arrangement of the bipyridine ligands. The Ru-N(monodentate) distance is longer for the ammonia complex (2.106(3) Å) than for the acetonitrile complex (2.008(4) Å); there are no significant differences in the distances and angles of the two Ru(bpy)₂ frameworks.     

X-ray structures of tris(0-cyclohexyl-dithiocarbonato)bismuth(III) and tris(0-benzyl-dithiocarbonato)bismuth(III)

The crystal structures of two Bi tris xanthates are reported, namely [Bi(S₂CO-c-C₆H₁₁)₃ J and [Bi(S₂COCH₂C₆H₅)₃]. They exist as centrosymmetric dimers, owing to the presence of bridging xanthate ligands, with seven-coordinate Bi atoms. The presence of a stereochemically active lonepair of electrons in each structure distorts the coordination geometry defined by seven S atoms and causes the elongation of some of the Bi-S bond distances. Crystals of both compounds are triclinic, space groupP¯1 with unit cell dimensions for [Bi(S₂CO-c-C₆H₁₁)₃]:a=12.417(3),b=13.571(3),c=9.681(4) Å;=102.30(2),=109.21(2), =66.23(2)° andZ=2; and for [Bi(S₂COCH₂C₆H₅)₃]:a=14.747(2),b=15.966(2),c=5.991(1) Å;=95.08(1),=98.51(1), =104.92(1)° andZ=2. The structures were refined by a full-matrix least-squares procedure to finalR=0.045 using 4274 reflections for [Bi(S₂CO-c-C₆H₁₁)₃] and toR=0.027 using 3993 reflections for [Bi(S₂COCH₂C₆H₅)₃].