基于增强瑞利反馈的单模窄线宽随机激光器

仿真说明了单模光纤(SMF)中瑞利散射(RS)的机理, 指出纤芯掺杂的不均匀性以及拉丝过程引起的光纤几何尺寸的随机变化是光纤中RS产生的主要原因, 并以此为基础制作了损耗为0.54 dB/km的散射光纤. 在通信波段, 5 km该散射光纤的瑞利背向散射(RBS)强度高于相同长度的SMF-28近5 dB. 在基于RBS单模随机激光器的数值模拟中, 大量的具有随机幅度和相位的纵模在经历不平坦增益的多次放大之后, 只有在增益最大点附近的模式能够克服损耗成为输出模式. 实验中以掺铒光纤作为增益介质, 500 m散射光纤提供随机反馈, 窄带布拉格光纤光栅(FBG)作为波长选择器件, 得到线宽约3.5 kHz、对比度近50 dB的单模激光输出. 与采用相同长度SMF-28的随机激光器相比, 其阈值电流降低了80 mA, 相同抽运条件下的最大输出功率提高了3 dBm. 该单模窄线宽随机激光器的输出波长的调谐特性仅由FBG的中心波长决定.     

A distributed feedback dye laser based on higher order Bragg scattering

A distributed feedback dye laser based on second order Bragg scattering due to a sinusoidal susceptibility modulation is reported. Rhodamine 6G dye solution in three different solvents; methanol, ethanol and benzyl alcohol is pumped by interference fringes produced by two beams from the second harmonic of Nd:YAG laser. Output power is plotted as a function of the pump power. The spectrum of dye laser shows a new type of modulation.     

Statistical properties of Er/Yb co-doped random Rayleigh feedback fiber laser

In this Letter, we experimentally investigate fast temporal intensity dynamics and statistical properties of the claddingpumped Er/Yb co-doped random Rayleigh feedback fiber laser(EYRFL) for the first time, to the best of our knowledge. By using the optical spectral filtering method, strong and fast intensity fluctuations with the generation of extreme events are revealed at the output of EYRFL. The statistics of the intensity fluctuations strongly depends on the wavelength of the filtered radiation, and the intensity probability density function(PDF) with a heavy tail is observed in the far wings of the spectrum. We also find that the PDF of the intensity in the central part of the spectrum deviates from the exponential distribution and has the dependence on the laser operating regimes, which indicates some correlations among different frequency components exist in the EYRFL radiation and may play an important role in the random lasing spectrum stabilization process.     

Non-intrusive flow measurement based on a distributed feedback fiber laser

We propose a new non-intrusive flow measurement method using the distributed feedback fiber laser(DFB-FL)as a sensor to monitor flow in the pipe.The relationship between the wavelength of the DFB-FL and the liquid flow rate in the pipeline is derived.Under the guidance of this theory,the design and test of the flow sensor is completed.The response curve is relatively flat in the frequency range of 10 Hz to 500 Hz,and the response of the flow sensor has high linearity.The flow from 0.6 m^3/h to 25.5 m^3/h is accurately measured under the energy analysis method in different frequency intervals.A minimum flow rate of 0.046 m/s is achieved.The experimental results demonstrate the feasibility of the new non-intrusive flow measurement method based on the DFB-FL and accurate measurement of small flow rates.     

紧凑型窄线宽分布反馈光纤激光器

 在铒/镱共掺杂有源光纤上直接刻蚀光栅,制成一台紧凑型非对称π相移分布反馈光纤激光器。光栅总长度约50 mm,最佳相移位置在29 mm处,最佳耦合系数为150 m^-1。采用980 nm激光二极管同向泵浦,当最大泵浦功率为200 mW时,在1 550.94 nm处实现约10 mW激光输出,线宽小于0.05 nm,阈值约35 mW,斜率效率为6.06%,总光 光转换效率为5%,基本满足长距离光通信系统光源功率实用化的要求。     

Single-frequency Brillouin distributed feedback fiber laser

We demonstrate a single-frequency Brillouin distributed feedback laser (DFB). The DFB laser cavity was a 12.4 cm long fiber Bragg grating with a π-phase shift offset from the grating center. It exhibited a threshold of 30 mW and conversion efficiency from pump to Stokes wave as high as 27%. Higher-order Stokes waves were suppressed by more than 20 dB. The Stokes output of the laser could be obtained in either the forward or backward direction, simply by changing the orientation of the offset of the discrete phase shift with respect to the pump propagation direction. The DFB laser operated over a pump frequency range of 1.2 GHz, more than 60 times larger than the SBS gain bandwidth.     

Multiwavelength fiber laser based on a photonic crystal fiber loop mirror with cooperative Rayleigh scattering

In this work, a multiwavelength fiber Raman laser based on a highly birefringent photonic crystal fiber loop mirror is presented. A laser resonator is formed when the Raman amplification with cooperative Rayleigh scattering in a dispersion-compensating fiber is used as a distributed mirror and combined with a photonic crystal fiber loop mirror filtering structure. Stable multiwavelength lasing at room temperature is achieved due to the low temperature sensitivity of the highly birefringent photonic crystal fiber.     

A mirror based on stimulated brillouin scattering with a double feedback loop in a laser cavity

The possibility of switching an external mirror based on stimulated Brillouin scattering (SBS) with a double feedback loop to a laser cavity is shown experimentally. A significant increase in the output laser power is obtained with conservation of the diffraction quality of the initial radiation. Experimental comparison with an ordinary SBS mirror, excited in a single pass through a nonlinear medium, is performed and the advantage in the energy parameters of the scheme with a double feedback loop is shown. The threshold characteristics of the SBS mirror under study are calculated and good agreement with the experimental data is obtained.     

High‐power random distributed feedback fiber laser: From science to application

A fiber laser based on random distributed feedback has attracted increasing attention in recent years, as it has become an important photonic device and has found wide applications in fiber communications or sensing. In this article, recent advances in high‐power random distributed feedback fiber laser are reviewed, including the theoretical analyses, experimental approaches, discussion on the practical applications and outlook. It is found that a random distributed feedback fiber laser can not only act as an information photonics device, but also has the feasibility for high‐efficiency/high‐power generation, which makes it competitive with conventional high‐power laser sources. In addition, high‐power random distributed feedback fiber laser has been successfully applied for midinfrared lasing, frequency doubling to the visible and high‐quality imaging. It is believed that the high‐power random distributed feedback fiber laser could become a promising light source with simple and economic configurations.

     

Random distributed feedback fiber laser pumped by an ytterbium doped fiber laser

A random distributed feedback fiber laser operating at 1115 nm has been demonstrated experimentally in standard communication optical fibers by using a LD-pumped Yb-doped fiber laser as the pump source. We have studied the effect of different fiber spans on this new type of random fiber laser output power. It is shown that the generation power is the highest up to 198 mW in a 50 km fiber span. The slope efficiency is more than 28.7%. Stable, high-power continuous-wave (CW) lasing can be generated when the pump power is 3.6 W. The threshold power has also been calculated which well proves a random fiber laser operating via Rayleigh scattering, amplified through the Raman scattering.     

Self-Q-switching Nd: YAG laser operation using stimulated thermal Rayleigh scattering

We have developed a self-Q-switching phase-conjugated laser resonator in which a medium cell containing a strongly absorbing liquid is used to replace a cavity mirror and a Q-switch. A stable laser output is obtained with a single pulse and single frequency. Unlike previously published papers, a conventional starter cavity is not needed in our experiment. The mechanism of the laser operation is interpreted by stimulated thermal Rayleigh scattering.     

Effect of Rayleigh-scattering distributed feedback on multiwavelength Raman fiber laser generation

We experimentally demonstrate a Raman fiber laser based on multiple point-action fiber Bragg grating reflectors and distributed feedback via Rayleigh scattering in an ~22-km-long optical fiber. Twenty-two lasing lines with spacing of ~100 GHz (close to International Telecommunication Union grid) in the C band are generated at the watt level. In contrast to the normal cavity with competition between laser lines, the random distributed feedback cavity exhibits highly stable multiwavelength generation with a power-equalized uniform distribution, which is almost independent on power.     

Near-infrared methane sensor based on a distributed feedback laser

In this article, a near-infrared methane detection system using tunable diode laser absorption spectroscopy technology was designed and implemented. The distributed feedback laser was driven by a self-developed temperature and current controller to allow scanning the selected absorption wavelength at 1654?nm. Laser temperature fluctuation was lower than 0.01%, and the output emission wavelength was linear and stable. The emitted beam passed a reflective gas chamber and was received by the Indium Gallium Arsenide photodiode detector. Through a data acquisition card, a digital lock-in amplifier was developed to extract the second harmonics with real-time monitoring and adjustment. Based on Allan deviation analysis, the limit of detection was about 48?ppm with a path length of 30?cm, at an integration time of 6?s. The experimental results revealed a maximum detection error of less than 3% at a gas concentration higher than 100?ppm. The fluctuations rates in long-term (9?hr) stability measurements for 1?×?10³?ppm and 1?×?10⁴?ppm methane samples were 0.8% and 0.48%, respectively, indicating good stability for the sensor. In the control module design, compared with previous reports on methane detection systems, the current system uses a self-developed temperature controller, a current driver and a signal processor, to allow real-time display and adjustments. The potential for adjustable wavelength scanning is available for multi-gas detection based on a single detection system.     

光纤分布式扰动传感器中瑞利和受激布里渊散射光谱特性及其影响研究

针对光纤分布式扰动传感器长距离应用定位误差增大的问题,研究了传感器长距离光纤中的瑞利散射和受激布里渊散射的光谱特性及其对系统定位精度的影响.建立了长距离光纤中瑞利和受激布里渊散射的数学模型,通过仿真研究发现散射光波的杂波干涉和强度噪声会严重降低干涉仪的光学信噪比,从而导致定位误差.通过实验验证了仿真结果的正确性.研究结...     

高频调制大功率窄线宽分布反馈光纤激光器

研制了一种窄线宽光纤激光器.在有源相移光栅后加一段掺铒光纤,当用980 nm抽运光注入时,首先形成了分布反馈(DFB)光纤激光器,而残余抽运光将铒纤中铒离子从基态抽运到了激发态,对DFB激光实现了有效放大,实现了对残余抽运光的充分利用,节省了功耗、降低了成本;同时利用温控技术克服了DFB光纤激光器的温度敏感问题;将相移光栅黏贴于片状压电陶瓷(PZT)的表面实现了高频调制.实验研制的激光器的最高调制频率为2 kHz、输出功率为15.6 dBm,线宽为300 kHz. 关键词： 分布反馈光纤激光器 窄线宽 大功率 高频调制     

高非线性微结构光纤中基于受激布里渊散射的慢光延迟

全光连续可调的慢光技术在全光网络和光信息处理等领域具有重要的应用前景. 利用自行设计并拉制的高非线性微结构光纤, 实验研究了基于受激布里渊散射的可调谐慢光延迟. 采用单抽运光和单级延迟方案, 当抽运光功率为162.6 mW时, 在长度为120 m的高非线性微结构光纤中获得了最大76 ns的延迟量, 相当于0.76个脉冲宽度. 通过调节抽运光功率的大小, 可以实现对慢光延迟量的可调谐.该慢光延迟方案具有延迟量大、 全光可调谐及与现有光通信系统兼容等优势. 关键词： 慢光 微结构光纤 受激布里渊散射     

分布反馈式光纤激光器线宽特性及其展宽机理研究

针对分布反馈式光纤激光器(DFB-FL)线宽特性进行了深入研究.通过理论推导和实验验证, 分析了自脉动、相 移光栅、激射窗口宽度以及外界环境扰动等因素对DFB-FL线宽的展宽作用. 进一步提出了压缩DFB-FL线宽的有效方法和途径,给出了自注入锁模方式下对DFB-FL线宽压缩的对比实验结果, 将DFB-FL的线宽从35 kHz压缩到了10 kHz.     

Widely tunable linear-cavity multiwavelength fiber laser with distributed Brillouin scattering

We demonstrate a multiple wavelength Brillouin/erbium fiber laser in a linear cavity configuration.The laser cavity is made up of a fiber loop mirror on one end of the resonator and a virtual mirror generated from the distributed stimulated Brillouin scattering effect on the other end.Due to the weak reflectivity provided by the virtual mirror,self-lasing cavity modes are completely suppressed from the laser cavity.At Brillouin pump and 1480-nm pump powers of 2 and 130 mW,respectively,11 channels of the demonstrated laser with an average total power of 7.13 dBm can freely be tuned over a span of 37-nm wavelength from 1530 to 1567 nm.     

Amplification effect on SBS and Rayleigh scattering in the backward pumped distributed fiber Raman amplifier

The amplification effect on stimulated Brillouin scattering （SBS） and Rayleigh scattering in the backward pumped G652 fiber Raman amplifier （FRA） is studied. The pump source is a 1427.2-nm fiber Raman laser whose power is tunable between 0 - 1200 mW, and the signal source is a tunable narrow spectral bandwidth （〈 10 MHz） external cavity laser （ECL）. The Rayleigh scattering lines are amplified by the FRA and Stokes SBS lines are amplified by the FRA and the fiber Brillouin amplifier. The total gain of SBS lines is the production of the gain of Raman amplifier and that of Brillouin amplifier. In experiment, the SBS gain is about 42 dB and the saturation gain of 25-km G652 backward FRA is about 25 dB, so the gain of fiber Brillouin amplifier is about 17 dB.