V-band directional tandem coupler of monolithic uniplanar structure

We present a uniplanar coplanar-waveguide 3-dB tandem coupler operating at V-band frequencies. The uniplanar structure is monolithically fabricated by using two-section parallel-coupled lines and air-bridge crossovers replacing the conventional multilayer or bonded structures. Due to an optimized tandem structure and non-bonded crossovers minimizing the parasitic components, a maximum coupling of 2.5 dB is measured at 62 GHz with a 2 dB bandwidth of 83%, while a high directivity factor of 33 dB is simultaneously obtained at 58–62 GHz. Over the entire design frequency range of 30–90 GHz, we achieve good phase unbalance of 90 ± 6.0°, as well as return loss and isolation lower than −23 and −16 dB, respectively.     

Investigation on push-pull polymer Mach-Zehnder interferometer electro-optic switches using improved 3-D mode propagation analysis method

By introducing normalized mode excitation coefficient and total mode excitation coefficient, we improve the 3-D mode propagation analysis (MPA) method for convenient design and analysis of multimode interference (MMI) coupler. With the improved 3-D MPA method and point-matching method, we present a novel formulation technique to analyze the low- and high-frequency characteristics for the impedance-matched polymer Mach-Zehnder interferometer electro-optic (EO) switch based on MMI couplers. As an application, under 1550 nm, optimization and simulation performed for the designed device reveal low driving voltage of 1.375 V with short EO region length of 5 mm. The insertion loss and extinction ratio are less than 3.75 dB and more than 42 dB, respectively. The microwave characteristic impedance is about 49.6 Ω, and due to the less mismatch between lightwave velocity and microwave velocity, the estimated cutoff switching frequency is up to 263 GHz with the 10–90% rise time and fall time about 1.90 ps under the operation of step-style square-wave switching signal. This theoretical cutoff switching frequency is almost 1.53 times of that of our previous reported shielded EO switch with similar design technique.     

Design of a polymer directional coupler electro-optic switch using two-section reversed electrodes

By using the coupled mode theory, electro-optic modulation theory, conformal transforming method and image method, the structure is designed, the parameters are optimized, and the characteristics are analyzed for a polymer directional coupler electro-optic switch with two-section reversed electrodes. Simulation shows that the designed device exhibits excellent switching functions. Under the operation wavelength of 1550 nm, the electro-optic coupling region length is 4751 μm, the cross-state and bar-state voltages are about 1.22 and 2.65 V, and the insertion loss and crosstalk are less than 2.21 and −30 dB, respectively. By slightly adjusting the state voltages, the blight of the fabrication errors on the switching characteristics can be easily eliminated. The calculation results of the presented technique are in good agreement with those of the beam propagation method (BPM).     

Design of an insensitive-polarization all-optical switch based on multimode interference structures

This paper presents a new design for an insensitive-polarization all-optical switch using 2 × 2 multimode interference (MMI) couplers. The switching structure can operate at central operating wavelength 1550 nm for both polarizations. A nonlinear directional coupler is used to realize the phase shifter and therefore switching mechanism is obtained. The transfer matrix method and beam propagation method are used to design and optimize the whole device structure.     

High speed ultra short pulse fiber ring laser using photonic crystal fiber nonlinear optical loop mirror

A scheme to generate high speed optical pulse train with ultra short pulse width is proposed and experimentally studied. Two-step compression is used in the scheme: 20 GHz and 40 GHz pulse trains generated from a rational harmonic actively mode-locked fiber ring laser is compressed to a full width at half-maximum (FWHM) of ~ 1.5 ps using adiabatic soliton compression with dispersion shifted fibers (DSF). The pulse trains then undergo a pedestal removal process by transmission through a cascaded two photonic crystal fiber (PCF)-nonlinear optical loop mirrors (NOLM) realized using a double-ring structure. The shortest output pulse width obtained was ~ 610 fs for 20 GHz pulse train and ~ 570 fs for 40 GHz pulse train. The signal to noise ratio of the RF spectrum of the output pulse train is larger than 30 dB. Theoretical simulation of the NOLM transmission is conducted using split-step Fourier method. The results show that two cascaded NOLMs can improve the compression result compared to that for a single NOLM transmission.     

Fabrication and characterization on an organic/inorganic 2 × 2 Mach–Zehnder interferometer thermo-optic switch

An organic/inorganic hybrid 2 × 2 directional coupler (DC) Mach–Zehnder interferometer (MZI) thermo-optic (TO) switch was successfully designed and fabricated using simple direct ultraviolet photolithography process. The hybrid organic/inorganic waveguide structure includes poly-methyl-methacrylate-glycidyl-methacrylate (P(MMA-GMA)), SU-8 2005 and silica as core, upper cladding and under cladding, respectively. Device optimization and simulation were performed to decrease radiation loss and leakage loss, quicken response time and cut down power consumption. Measurements of the fabricated devices at 1550 nm wavelength result in a switching power of 7.2 mW, a response time of ∼100 μs, and crosstalk of −22.8 and −26.5 dB under cross state and bar state, respectively. Besides, the driving-noise-tolerance characteristics of this device were experimentally investigated by directly imposing a generated tunable noise on the pure driving signal (4 V_pp) and the minimum extinction ratio is larger than 18 dB under a noise level of 2.5 V_pp. The effect of noise on extinction ratio was found decreased with the increase of noise frequency.     

Al/CdSe/GaSe/C resonant tunneling thin film transistors

An Al/CdSe/GaSe/C thin film transistor device was prepared by the physical vapor deposition technique at a vacuum pressure of 10⁻⁵ mbar. The x-ray diffraction measurements demonstrated the polycrystalline nature of the surface of the device. The dc current-voltage characteristics recorded for the Al/CdSe/C and Al/CdSe/GaSe/C channels displayed a resonant tunneling diode features during the forward and reverse voltage biasing, respectively. In addition, the switching current ratio of the Al/CdSe/C increased from 18.6 to 9.62×10³ as a result of the GaSe deposition on the CdSe surface. Moreover, the alternating electrical signal analyses in the frequency range of 1.0 MHz to 1.8 GHz, showed some remarkable properties of negative resistance and negative capacitance spectra of the Al/CdSe/GaSe/C thin film transistors. Two distinct resonance-antiresonance phenomena in the resistance spectra and one in the capacitance spectra were observed at 0.53, 1.04 and 1.40 GHz for the Al/CdSe/C channel, respectively. The respective resonating peak positions of the resistance spectra shift to 0.38 and 0.95 GHz when GaSe is interfaced with CdSe. These features of the thin film transistors are promising for use in high quality microwave filtering circuits and also for use as ultrafast switches.     

Single tone and multi tone microwave over fiber communication system using direct detection method

In this paper, an analog microwave over fiber link for long haul distance based upon Rate Equation Laser is demonstrated. This system uses the advantage of high potential bandwidth of fiber in transmission of microwave signal. The interface of the two systems needs an up-conversion of microwave band into baseband (at which fiber operates). An Intensity Modulation Direct Detection (IMDD) technique is used to achieve this purpose. The Rate Equation laser is operated in a dynamic state, where its intensity oscillates at a microwave frequency that varies with the input signal fed by wave generator. This system can also use for two modulating tones. The frequency of the first tone is varied from 1 to 20 GHz and second is set at 5 GHz. A data signal of 10 Gbps is transmitted over long haul single mode fiber by single tone system. A very good bit error rate (BER) 10^?40 performances for 100 km and 25 km fiber link is achieved for both single tone and two tones respectively in proposed microwave over fiber communication system.     

Improvement of stability and pulse energy in a diode-pumped dual-loss-modulated QML Nd:Lu0.2Y0.8VO4 laser with EO modulator and GaAs

The Q-switched and mode-locked (QML) performance in a diode-pumped Nd:Lu_0.2Y_0.8VO₄ laser with electro-optic (EO) modulator and GaAs saturaber absorber is investigated. In comparison with the solely passively QML laser with GaAs, the dual-loss-modulated QML laser with EO and GaAs can generate pulses with higher stability and shorter pulse width of Q-switched envelope, as well as higher pulse energy. At the repetition rate 1 kHz of EO, the pulse width of Q-switched pulse envelope has a compression of 89% and the pulse energy has an improvement of 24 times. The QML laser characteristics such as the pulse width, pulse peak power etc. have been measured for different small-signal transmittance (T₀) of GaAs, different reflectivity (R) of output coupler and modulation frequencies of the EO modulator (f_e). The highest peak power and the shortest pulse width of mode-locked pulses are obtained at f_e = 1 kHz, R = 90% and T₀ = 92.6%. By considering the influences of EO modulator, a developed rate equation model for the dual-loss-modulated QML laser with EO modulator and GaAs is proposed. The numerical solutions of the equations are in good agreement with the experimental results.     

Photonic generation of millimeter-wave ultra-wideband signal using phase modulation to intensity modulation conversion and frequency up-conversion

We propose and experimentally demonstrate the generation of a pair of polarity-reversed 24 GHz millimeter-wave (MMW) ultra-wideband (UWB) monocycles. The scheme is realized by using delay interferometer (DI) based phase modulation to intensity modulation (PM–IM) conversion and carrier suppression modulation (CSM) based frequency up-conversion. The phase modulation is realized by using either electro-optic phase modulator (EOPM) or cross phase modulation (XPM) in semiconductor optical amplifier (SOA), which is an all-optical approach to obtaining baseband UWB signals, respectively. After frequency up-converted by using CSM in a Mach–Zehnder modulator (MZM), a pair of polarity-reversed 24 GHz MMW-UWB signals complying with the Federal Communication Committee (FCC) requirements is generated. The bi-phase modulation (BPM) of 24 GHz MMW-UWB signals can also be realized by electrically switching the bias voltage of delay interferometer.     

Optically switchable all-fiber optic polarization rotator

This study demonstrates an all-fiber optical polarization rotator and switch based on a side-polished fiber (SPF) overlaid with a photoresponsive liquid crystal (LC) containing a nematic LC and a photosensitive azobenzene molecule. The trans-cis photoisomerization of azobenzene modulates the overlaid LC's birefringence, changes the refractive index (RI) of the photoresponsive LC-overlaid SPF, and further controls and switches the phase retardation. This design achieves a 10° phase shift under switching time of less than 1 s. The demonstration has potential for an optically tunable in-line 2 × 2 fiber-optic switch or microstructured fiber-based photonic device controlled by the polarization of light.     

RF behavior of triple-frequency high power fusion gyrotron

The RF behavior of high power, triple frequency (170-, 127.5-, and 85 GHz) gyrotron for fusion application is presented in this paper. The operating mode selection is discussed in detail for each corresponding frequencies and TE_34,10, TE_25,8 and TE_17,5 modes are selected as the operating mode for 170 GHz, 127.5 GHz and 85 GHz operation of the device, respectively. The interaction cavity geometry and beam parameters are finalized by the cold cavity analysis and beam-wave interaction simulations. Considering the beam parameters and the beam launching positions in cavity (beam radius), the design of Magnetically Tunable MIG (MT-MIG) is also presented. Results of MT-MIG confirm the beam launching with desired beam parameters at the beam radius corresponding to the selected operating modes for all three frequencies. The CVD diamond window is also designed for RF power transmission. The beam-wave interaction simulations confirm more than 1 MW power at all three frequencies (170-, 127.5-, and 85 GHz).     

Improvement of all-optical switching performance based on azo dye-doped polymer film using two cross-linearly polarized pump beams

We propose a method for improving the characteristics of all-optical switching based on azo dye-doped polymers. Using alternately two cross-linearly polarized beams (532 nm, continuous light wave (CW)) to pump azo dye–ethyl red (ER) doped polymer methyl methacrylate (PMMA) film, the modulation depth of the all-optical switching reached 96% at the pump powers of 4.8 mW and 1.6 mW and the modulation frequency of 1000 Hz. For comparison, we used respectively the single linearly polarized beam (4.8 mW) and the alternately linear–circular polarized beams (4.8 mW and 1.6 mW) to pump the film at the modulation frequency of 1000 Hz, the obtained modulation depths of the all-optical switching were 36% and 45.8%, respectively. Furthermore, the experimental measurement and analysis showed that the turn off speed of the all-optical switching could be obviously increased by use of our pump method.     

Galvanostatically deposited Fe: MnO2 electrodes for supercapacitor application

The present investigation describes the addition of iron (Fe) in order to improve the supercapacitive properties of MnO₂ electrodes using galvanostatic mode. These amorphous worm like Fe: MnO₂ electrodes are characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), energy dispersive X-ray analysis (EDAX), Fourier transform infrared spectroscopy (FTIR) and wettability test. The supercapacitive properties of MnO₂ and Fe: MnO₂ electrodes are investigated using cyclic voltammetry, chronopotentiometry and impedance techniques. It is seen that the supercapacitance increases with increase in Fe doping concentration and achieved a maximum of 173 F g^?1 at 2 at% Fe doping. The maximum supercapacitance obtained is 218 F g^?1 for 2 at% Fe: MnO₂ electrode. This hydrous binary oxide exhibited ideal capacitive behavior with high reversibility and high pulse charge–discharge property between ?0.1 and +0.9 V/SCE in 1 M Na₂SO₄ electrolyte indicating a promising electrode material for electrochemical supercapacitors.     

Electromagnetic wave absorption properties of ε-Fe3N/Y2O3 nanocomposites derived from Y2Fe17 intermetallic compound

The electromagnetic wave absorption properties of ε-Fe₃N/Y₂O₃ nanocomposites were characterized in a frequency range of 0.05–20.05 GHz. The imaginary part of relative permeability μ_r″ exhibited “twin peak” dispersion and μ_r″ value retained high over a 0.5–10 GHz range. The real part (ε_r′) and imaginary part (ε_r″) of relative permittivity almost kept a low constant in a region of 0.5–10 GHz, respectively. As a result, the resin composites with 51 vol% ε-Fe₃N/Y₂O₃ powders exhibited excellent electromagnetic wave absorption properties (RL<−20 dB) in a frequency range of 0.6–4.4 GHz, with a thickness of 3.3–19.3 mm. A minimum reflection loss of −55 dB was observed at 1.8 GHz with an absorber thickness of 7.05 mm.     

IQ quadrature demodulation algorithm used in heterodyne detection

In order to obtain better detection results of heterodyne, we used phase IQ quadrature demodulation algorithm to process the data which detected by laser heterodyne. Based on laser heterodyne interferometer, processing the data in the interferometer phase IQ quadrature demodulation algorithm from the signal to noise ratio, sampling rate, sampling rate, filter order and cutoff frequency, verify the effects of these system parameters to the phase precision, and choose the best parameters to obtain a better phase precision through experiment as: the signal to noise ratio is 25 dB, the IF signal frequency is 98.3 MHz, 98.5 MHz, 99.1 MHz, 99.5 MHz and 100 MHz, the sampling rate is 512–2048, the cutoff frequency and order of the filter are 0.11 and 40, respectively.     

Novel attributes of AlGaN/AlN/GaN/SiC HEMTs with the multiple indented channel

In this paper, a high performance AlGaN/AlN/GaN/SiC High Electron Mobility Transistor (HEMT) with the multiple indented channel (MIC-HEMT) is proposed. The main focus of the proposed structure is based on reduction of the space around the gate, stop of the spread of the depletion region around the source–drain, and decrement of the thickness of the channel between the gate and drain. Therefore, the breakdown voltage increases, meanwhile the elimination of the gate depletion layer extension to source/drain decreases the gate–source and gate–drain capacitances. The optimized results reveal that the breakdown voltage and the drain saturation current increase about 178% and 46% compared with a conventional HEMT (C-HEMT), respectively. Therefore, the maximum output power density is improved by factor 4.1 in comparison with conventional one. Also, the cut-off frequency of 25.2 GHz and the maximum oscillation frequency of 92.1 GHz for the MIC-HEMT are obtained compared to 13 GHz and 43 GHz for that of the C-HEMT and the minimum figure noise decreased consequently of reducing the gate–drain and gate–source capacitances by about 42% and 40%, respectively. The proposed MIC-HEMT shows a maximum stable gain (MSG) exceeding 24.1 dB at 3.1 GHz which the greatest gain is yet reported for HEMTs, showing the potential of this device for high power RF applications.     

Experimental implementation of an all-optical OFDM system based on time lens

A real time all-optical orthogonal frequency division multiplexing (OOFDM) system based on two time lenses is experimentally demonstrated. At the transmitter, groups of initial optical pulses are transformed into OOFDM symbols by a continuous inverse Fourier transform (IFT) device, which consists of the first a quadratic phase modulator and two high dispersive elements. After transmission, a continuous Fourier transform (FT) device, consisting of another quadratic phase modulator and two high dispersive elements, rebuilds the initial optical pulses at the receiver. The electrical sinusoidal waveform employed in the FT module at the receiver is obtained directly from the transmitter with certain phase shift. In the system, the guard interval is necessary for each OOFDM symbol to ensure the initial pulses are operated FT/IFT under a parabolic waveform driving and to have more Fourier transformation time window. Experiment results show that 8 × 2.5 Gb/s signals successfully transmit through 200-km-G.655 fibers without any dispersion compensation, with the BER being 10^? 12.     

Towards a 1 MW, 170 GHz gyrotron design for fusion application

The electrical design of different components of 1 MW, 170 GHz gyrotron such as, magnetron injection gun, cylindrical interaction cavity and collector and RF window is presented in this article. Recently, a new project related to the development of 170 GHz, 1 MW gyrotron has been started for the Indian Tokamak. TE_34,10 mode is selected as the operating mode after studied the problem of mode competition. The triode type geometry is selected for the design of magnetron injection gun (MIG) to achieve the required beam parameters. The maximum transverse velocity spread of 3.28% at the velocity ratio of 1.34 is obtained in simulations for a 40 A, 80 kV electron beam. The RF output power of more than 1 MW with 36.5% interaction efficiency without depressed collector is predicted by simulation in single-mode operation at 170 GHz frequency. The simulated single-stage depressed collector of the gyrotron predicted the overall device efficiencies >55%. Due to the very good thermal conductivity and very weak dependency of the dielectric parameters on temperature, PACVD diamond is selected for window design for the transmission of RF power. The in-house developed code MIGSYN and GCOMS are used for initial geometry design of MIG and mode selection respectively. Commercially available simulation tools MAGIC and ANSYS are used for beam–wave interaction and mechanical analysis respectively.     

High LO-to-RF isolation 94 GHz coplanar monolithic down-converter for FMCW radar sensor applications

This paper presents a 94 GHz monolithic down-converter with low conversion loss and high local oscillator (LO)-to-RF isolation using the 0.1 μm T-gate metamorphic high electron-mobility transistor (MHEMT) technology. The down-converter consists of a one-stage amplifier and a single-balanced mixer based on the high-directivity tandem coupler structure using the air-bridge crossovers, thereby amplifying the RF signals and maximizing the LO-to-RF isolation by using an inherent S₁₂ isolation characteristic of the amplifier and good phase balance of the tandem coupler. The fabricated one-stage amplifier using a 30 μm × 2 MHEMT shows a small signal gain of 7 dB at 94 GHz. The single-balanced mixer comprising two 20 μm × 2 MHEMT Schottky diodes and the tandem coupler with an additional λ/4-length line exhibits the conversion loss less than 7.8 dB and the LO-to-RF isolation higher than 30 dB in a RF frequency range of 91–96 GHz. Two circuits designed both for a 50 Ω impedance system are integrated into the down-converter of a 2.6 × 2.5 mm² chip size, and it shows a low conversion loss of ∼1 dB at 94 GHz and excellent LO-to-RF isolation above 40 dB in a frequency range of 90–100 GHz. This is the best isolation among the W-band monolithic down-converters reported to date.