2.14 kW级联泵浦光纤放大器

利用大模场掺镱光纤搭建了1018 nm高功率光纤激光器,获得了476 W的最高输出功率。利用6台高亮度1018 nm光纤激光器泵浦掺镱光纤,搭建了全光纤结构的级联泵浦光纤放大器,实现了2.14 kW的最高输出功率,输出功率随泵浦功率线性增长,整体斜率效率为86.9%,M2因子为1.9。     

2.14kW级联泵浦光纤放大器

利用大模场掺镱光纤搭建了1018nm高功率光纤激光器,获得了476 W的最高输出功率。利用6台高亮度1018nm光纤激光器泵浦掺镱光纤,搭建了全光纤结构的级联泵浦光纤放大器,实现了2.14kW的最高输出功率,输出功率随泵浦功率线性增长,整体斜率效率为86.9%,M2因子为1.9。     

High-power tandem pumped fiber amplifier with an output power of 2.9 kW

We report on a high power fiber amplifier tandem pumped by an industrial style thin-disk laser. An output power of 1 kW and a very good slope efficiency of 73% have been obtained for a state-of-the-art photonic crystal fiber originally designed for short-pulse amplification. We also compare this result to an experiment, where a power of 2.9 kW could be obtained from a step-index large-mode-area fiber with the same slope efficiency.     

包层泵浦fs光纤放大器的实验研究

 在实验上对双包层光纤放大器进行了研究。采用新型内包层为六边形的铒镱共掺双包层光纤作为放大介质,用带尾纤的半导体激光器进行泵浦,对fs光脉冲进行放大。当用2.5 W的入纤功率泵浦50 cm长的双包层铒镱光纤时,把平均功率为10.8 mW、重复频率20.84 MHz的激光放大到176 mW,增益为12.2 dB,相应的单脉冲能量为8.1 nJ,放大后脉冲宽度为480 fs,峰值功率为16 kW。     

包层泵浦fs光纤放大器的实验研究

在实验上对双包层光纤放大器进行了研究。采用新型内包层为六边形的铒镱共掺双包层光纤作为放大介质,用带尾纤的半导体激光器进行泵浦,对fs光脉冲进行放大。当用2.5 W的入纤功率泵浦50 cm长的双包层铒镱光纤时,把平均功率为10.8 mW、重复频率20.84 MHz的激光放大到176 mW,增益为12.2 dB,相应的单脉冲能量为8.1 nJ,放大后脉冲宽度为480 fs,峰值功率为16 kW。     

LD直接泵浦全光纤激光器输出功率突破20 kW

高功率光纤激光器具有高效率、小体积、低成本、抗回光能力强等突出优点,在工业加工等应用领域中具有明显的竞争优势。近期,国防科技大学基于光纤耦合半导体激光器(LD)直接泵浦的主振荡功率放大器(MOPA)实现了单纤20.27 kW的功率输出。放大器采用纯后向泵浦方案,中心波长1080 nm,光光效率达到84.8%,拉曼散射抑制比大于50 dB。通过优化光纤和器件的设计,可进一步提升激光器的功率和光束质量。     

High output power Erbium-Ytterbium doped cladding pumped fiber amplifier

The performance of a high output power Erbium-Ytterbium doped fiber amplifier (EYDFA) pumped by a 927 nm laser diode are proposed and experimentally investigated. The EYDFA provides a flat gain and output power higher than 23 dBm in the wavelength region from 1545 to 1566 nm using a double-pass configuration. A broadband fiber Bragg grating is used in the double-pass EYDFA to allow a double-propagation of the test signal in the gain medium and thus improves the gain and output power characteristics of the amplifier. The maximum output power of 390 mW is obtained at the maximum 927 nm pump power of 4.1 W which translates to a power conversion efficiency of about 10%.     

强泵浦条件下光纤放大器相位噪声的测量

利用多抖动法对强泵浦条件下光纤放大器引入的相位噪声进行了测量。利用功率谱、积分谱对具体泵浦条件下的相位噪声特性进行定性分析,结果表明,泵浦功率越大,高频成分占的比例越大。利用结构函数定量分析相位噪声的变化特性,得出相位噪声控制系统的带宽需求指标。实验测得在71,181和230 W泵浦条件下,所需相位控制系统带宽最小值分别为830 Hz,3.1 kHz和10 kHz。     

Pulsed pumped Yb-doped fiber amplifier at low repetition rate

A pulsed pumped Yb-doped double-clad fiber (DCF) master-oscillator power amplifier (MOPA) at low repetition rate is reported. Seeded by a passive Q-switched Nd:YAG microchip laser, the fiber amplifier can generate 167-kW peak-power and 0.83-ns duration pulses at 200-Hz repetition rate. Because of the pulsed pump approach, the amplified spontaneous emission (ASE) and the spurious lasing between pulses are well avoided, and the repetition rate can be set freely from single-shot to 1 kHz. Peak power scaling limitations that arise from the fiber facet damage are discussed.     

国产光纤实现同带抽运3000W激光输出

同带抽运是目前实现高功率光纤激光器的有效手段.本文基于同带抽运方式,以国产25/250μm掺镱双包层光纤为增益光纤,构建了全光纤化的主控振荡器功率放大器.实验中采用的国产光纤是中国电子科技集团公司第四十六研究所采用化学气相沉积结合气相-液相复合掺杂工艺制备的,其Yb~(3+)离子的分布更均匀,吸收截面更大,吸收系数更高.实验中,在种子光功率为67.8 W、抽运总功率为3511 W的条件下,实现了3079 W的激光输出,斜效率为85.9%,光束质量M~2约为2.14,3dB带宽为1.4nm,这是目前基于国产光纤同带抽运方式实现的最高功率.理论和实验结果表明国产光纤制备技术不断成熟,已经具备承受高功率输出的能力.继续提高抽运功率,优化增益光纤长度,改良散热方式,国产光纤有望实现更高功率的激光输出.     

单频光纤拉曼放大器的实验研究

本文进行了1031 nm抽运光对1080 nm单频信号光的拉曼放大实验,详细研究了单频信号光种子功率、拉曼增益光纤长度、抽运方式等因素对 单频光纤拉曼放大器(SF-FRA)输出特性的影响.结果表明,在未受受激布里渊散射(SBS)因素限制时,相同抽运功率条件下,单频信号光种子功率越高,SF-FRA的效率越高;拉曼增益光纤越长,SF-FRA的效率越高;前向抽运时,SF-FRA的效率较高.实验中发现SF-FRA的拉曼放大过程对单频信号光的线宽有较小的展宽.此外,单频信号光远场干涉短曝光图像的对比度为0.814,单频信号光与SF-FRA放大光远场干涉短曝光图像可见度为0.719,表明SF-FRA对单频信号光的相干性有一定影响.实验结论可为其他特殊波长SF-FRA的设计提供一定的参考.     

掺镱双包层光纤放大器分布泵浦方式下的优化算法

利用平均反转率迭代算法计算掺镱双包层光纤放大器分布泵浦方式下的稳态速率方程组,并采用遗传算法对分布泵浦功率的大小和每段光纤长度同时进行优化。评估函数中引入了每段光纤中最高温度的标准方差,以确保每段光纤中的最高工作温度是相同的。通过优化,7段泵浦的最高温度和标准方差分别为126.34 ℃和1.95 ℃ ,8段泵浦条件下的最高温度和标准方差分别为119.76 ℃和2.12 ℃。而未经优化的7段泵浦的最高温度和标准方差分别为147.12 ℃和21.37 ℃,8段泵浦条件下的最高温度和标准方差分别为139.95 ℃和20.83 ℃。计算结果表明：泵浦方式的优化降低了最高温度和标准方差,实现了光纤中温度分布的均匀性,并且通过增加泵浦段数可以进一步降低最高温度和平坦温度分布。     

掺镱双包层光纤放大器分布泵浦方式下的优化算法

 利用平均反转率迭代算法计算掺镱双包层光纤放大器分布泵浦方式下的稳态速率方程组,并采用遗传算法对分布泵浦功率的大小和每段光纤长度同时进行优化。评估函数中引入了每段光纤中最高温度的标准方差,以确保每段光纤中的最高工作温度是相同的。通过优化,7段泵浦的最高温度和标准方差分别为126.34 ℃和1.95 ℃ ,8段泵浦条件下的最高温度和标准方差分别为119.76 ℃和2.12 ℃。而未经优化的7段泵浦的最高温度和标准方差分别为147.12 ℃和21.37 ℃,8段泵浦条件下的最高温度和标准方差分别为139.95 ℃和20.83 ℃。计算结果表明：泵浦方式的优化降低了最高温度和标准方差,实现了光纤中温度分布的均匀性,并且通过增加泵浦段数可以进一步降低最高温度和平坦温度分布。     

Laser diode pumped bismuth-doped optical fiber amplifier for 1430 nm band

A 24 dB gain bismuth-doped fiber amplifier at 1430 nm pumped by a 65 mW commercial laser diode at 1310 nm is reported for the first time (to our knowledge). A 3 dB bandwidth of about 40 nm, a noise figure of 6 dB, and a power conversion efficiency of about 60% are demonstrated. The temperature behavior of the gain spectrum is examined.     

Remotely pumped hybrid double-pass L-band optical amplifier utilizing chirped fiber Bragg

This paper reported an investigation of remotely pumped double pass L-band amplifier with dispersion compensation technique. The proposed design used chirped fiber Bragg grating (CFBG) to reflect the amplified signal back into the active medium, compensate the effect of fiber dispersion and block the recycled forward amplified spontaneous emission (ASE) and the residual 1480 nm pump power. The characterization of the design was done experimentally. The gain is 37.5 dB and noise figure is 4 dB with best BER of 10⁻⁵² is achieved when the EDF is placed 150 km away from the transmitter and 48 km before the receiver terminal.     

Study on forward stimulated Brillouin scattering in a backward pumped fiber Raman amplifier

Strong multi-order forward stimulated Brillouin scattering (SBS) has been observed in the backward pumped S-band distributed fiber Raman amplifier (FRA) with tunable narrow signal source (less than 100 MHz) when the pump power of FRA reached the SBS threshold. This does not obey the theory that only weak backward SBS lines exist according to the conservation of energy and momentum and the wave vector selected rule. This is because the sound waveguide characteristic weakens the wave vector rule, and the forward transmitted sound waveguide Brillouin scattering lines are generated and amplified in FRA.When the pump power is further increased, 11 orders of SBS lines and comb-like profile are observed. For the excited line, the frequency is 197.2296 THz and the power is 0 dBm. The even order SBS lines are stronger than odd order SBS lines, the power of the 2nd and 4th order SBS lines is 1.75 dBm, which is 16 dB higher than that of the 1st and 3rd order SBS lines. The odd order SBS lines are named BrillouinRayleigh scattering lines.     

单端泵浦光纤放大器获得4 kW单模窄谱激光输出

窄谱光纤激光器在光束合成等领域有着广泛的应用,然而模式不稳定效应的出现严重限制着窄谱光纤激光器的功率提升。提出并验证了采用新型981 nm稳波长泵浦方案,能够应用于窄谱激光放大并提升模式不稳定效应阈值,通过采用单端后向泵浦结构,将单模窄谱光纤放大器功率提至4 kW以上。实验中采用白噪声相位调制展宽单频激光作为窄谱种子,主放大级分别采用稳波长976 nm和981 nm两种泵浦源单端后向泵浦。在采用976 nm泵浦源泵浦时,窄谱激光最高放大至3.4 kW,出现典型的模式不稳定效应特征,功率提升受到限制。在采用981 nm泵浦源泵浦时,窄谱激光最高放大至4.05 kW,且并未出现模式不稳定效应,输出光束质量M2因子为1.3,进一步功率提升仅受限于泵浦功率。通过优化激光器设计、结合双向泵浦结构,有望实现更高功率的窄谱光纤激光输出。     

高功率光子晶体光纤放大器实验研究

利用掺Yb³⁺的光子晶体光纤作为光纤放大器的增益介质,采用反向抽运方式,分别从理论和实验方面研究了不同信号的增益特性,在信号光功率为6W,抽运光功率为160W时,获得了104W的输出功率.实验发现,当抽运功率大于一定值时,放大器输出会有一定的不稳定性,并影响输出功率的进一步提高. 关键词： 光子晶体光纤 光纤放大器 反向抽运 高功率     

高功率、低量子亏损同带抽运掺镱光纤放大器

开展了基于同带抽运的高功率、低量子亏损的掺镱光纤放大器实验研究. 搭建了一台输出功率为21 W的1018 nm短波 长掺镱光纤激光器, 并利用其对双包层掺镱光纤进行同带抽运, 获得18.6 W的1080 nm波段激光输出, 光-光转换效率高达90.86%. 关键词： 光纤放大器 同带抽运 双包层光纤 转换效率     

Supercontinuum generation in seven-core photonic crystal fiber pumped by a broadband picosecond pulsed fiber amplifier

We report a supercontinuum source generated in seven-core photonic crystal fibers(PCFs) pumped by a self-made all-fiber picosecond pulsed broadband fiber amplifier. The amplifier's output average power is 60 W at 1150 nm with spectral width of 260 nm, and its repetition rate is 8.47 MHz with pulse width of 221 ps. With two different lengths of seven-core PCF, different output powers and spectra are obtained. When a 10 m long seven-core PCF is chosen, the output supercontinuum covers the wavelength range from 620 nm to 1700 nm, with the output power of 11.7 W. With only 2 m long seven-core PCF used in the same experiment, the wavelength of the supercontinuum spans from 680 nm to 1700 nm,with the output power of 20.4 W. The results show that the pulse width is 385 ps in the 10 m long seven-core PCF and 255 ps in the 2 m long one, respectively, due to the normal dispersion of the PCF.