A tunable and single-longitudinal-mode Ho:YLF laser

A 1.94 μm Tm-doped fiber laser pumped tunable single-longitudinal-mode Ho:YLF laser with double etalons was reported for the first time. The maximum single-longitudinal-mode output power of 345 mW at 2051.6 nm was achieved at the absorbed pump power of 11.9 W, corresponding to a slope efficiency of 5.5% and an optical conversion efficiency of 2.9%. By regulating the angle of the F–P etalons, the output wavelength of the laser can be tuned from 2051.6 nm to 2063.3 nm. The single-longitude-mode Ho:YLF laser operating at 2 μm can be used as the seed laser source of coherent Doppler lidar, differential absorption lidar and so on.     

Experimental study on tandem pumped fiber amplifier

We present the experimental results of a 1083 nm fiber amplifier tandem pumped by 1030 nm fiber laser. The output characteristics of the tandem pumped amplifier with cladding-pump and core-pump schemes are both investigated. The 1083 nm signal laser has not been efficiently amplified when cladding-pumped by 1030 nm laser for the weak absorption of the gain fiber. The core-pump scheme works well with the amplifier. The output properties with different gain fiber length are experimentally investigated. The maximum output power is 2.4 W with power conversion efficiency of 60%.     

Tunable single-longitudinal-mode operation of a sandwich-type YAG/Ho:YAG/YAG ceramic laser

We present a 2.09 μm single-longitudinal-mode sandwich-type YAG/Ho:YAG/YAG ceramic laser pumped by a Tm-doped fiber laser for the first time. A pair of F-P etalons was used to achieve tunable single-longitudinal-mode operation. The maximum single-longitudinal-mode output power of 530 mW at 2091.4 nm was obtained with an absorbed pump power of 8.06 W, corresponding to an optical conversion efficiency of 6.6% and a slope efficiency of 12.7%. Wavelength tunable was achieved by tuning the angle of etalons and the wavelength could be tuned from 2091.1 nm to 2092.1 nm, corresponding to a tuning frequency of 68 GHz. The M² factor was measured to be 1.23.     

A 980 nm Yb-doped single-mode fiber laser pumped by a 946 nm Q-switched Nd:YAG laser

We demonstrate a 980 nm single-mode Yb-doped fiber laser with a 946 nm Q-switched Nd:YAG laser used as the pump source. The experimental arrangement exploited a 36.5 cm length of fiber and used the output from both ends of the cavity, providing a total average output power of 100 mW with a slope efficiency of 38%. In order to increase the coupling efficiency and the practicability of the fiber laser, another experimental setup with single ended output was studied, producing an average output power of 80 mW from a fiber length of 23.5 cm. The pulse duration is 10 ns at a repetition frequency of 16 kHz. The linewidth of the laser is 4 nm, ranging from 977 to 981 nm.     

An experimental study of an acousto-optic Q-switched Yb3+-doped all-fiber laser

The Q-switched fiber lasers are very attractive sources in many applications such as military affairs, surgical operation, laser machining, laser marking, nonlinear frequency conversion, range finding, remote sensing and optical time domain reflectometer. In this paper, an acousto-optic Q-switched Yb³⁺-doped all-fiber laser at 1083 nm is reported. The pulse energy of 2.94 mJ has been obtained at the pump power of 8.47 W, and the pulse width is 3 μs.     

330 MHz,sub 50 fs Yb: Fiber ring laser

We demonstrate 330 MHz repetition rate operation in a ring cavity Yb:fiber laser with an innovative wavelength-division-multiplexing collimator to raise the repetition rate. The spectral bandwidth of the pulse is 30 nm and the dechirped pulse width is 48 fs. The output power is 70 mW with 600 mW, 975 nm pump laser diode.     

Compact resonantly intra-cavity pumped tunable Ho:Sc2SiO5 laser

A compact intra-cavity pumped low threshold continuous-wave Ho:Sc₂SiO₅ laser is reported. The characteristics of output wavelength tuning are investigated by use a intra-cavity briefringent (BF) filter. A wavelength tunable range of 140 nm from 2020 to 2160 nm is achieved. For the free-running mode, the laser slope efficiency is 24.8%, when the output central wavelength is 2110 nm. The laser threshold is about 820 mW of incident pump power. With the BF filter, a maximum output power of 870 mW is obtained at the incident pump power of 5 W, corresponding to a slope efficiency of 20.3%. The characteristics of output wavelength verse the crystal temperature are also investigated.     

Efficient high-power UV laser generated by an optimized flat–flat actively Q-switched laser with extra-cavity harmonic generations

We investigate the parasitic lasing effect in the high-power actively Q-switched laser with a flat–flat resonator. The parasitic lasing effect in the low-Q stage is found to lead to long tails in the output pulses, corresponding to the peak-power reduction. We experimentally determine the shortest cavity length without the parasitic lasing effect to optimize the performance of the high-power actively Q-switched laser with a flat–flat cavity. We further use the optimized fundamental laser to generate green and UV lasers by extra-cavity harmonic generations. At a pump power of 44 W, the output powers at 355 nm and 532 nm as high as 6.65 W and 8.38 W are obtained at a pulse repetition rate of 40 kHz.     

Multi-wavelength bismuth-based erbium-doped fiber laser based on four-wave mixing effect in photonic crystal fiber

A stable multi-wavelength erbium-doped fiber laser based on four-wave mixing (FWM) in a photonic crystal fiber (PCF) is demonstrated in this paper. The phase matching condition for four-wave mixing in the photonic crystal fiber has been enhanced using a seed signal and a polarisation controller to control the states of polarisation in the ring laser cavity. At a maximum pump power of 1480 nm, 5 lines are observed with nearly 2.15 nm spacing between the lines, and with a signal to noise ratio of more than 20 dB. The number of channels and wavelength spacing can be controlled by varying the output coupler ratio.     

Numerical analysis of a broadband spectrum generated in a standard fiber by noise-like pulses from a passively mode-locked fiber laser

This paper covers a numerical analysis of supercontinuum spectrum generation in a piece of standard fiber by using as the pump noise-like pulses produced by a passively mode-locked fiber laser. An experimental study was also carried out, yielding results that support the numerical results. In the numerical study we estimated that the spectral extension of the generated supercontinuum reaches ~ 1000 nm, and that it presents a high flatness over a region of ~ 220 nm (1630 nm-1850 nm) when we use as the pump noise-like pulses with a wide optical bandwidth (~ 50 nm) and a peak power of ~ 2 kW. Experimentally, the output signal spectrum extends from ~ 1530 nm to at least 1750 nm and presents a high flatness over a region of 1640 nm to 1750 nm for the same value of numerical input power, 1750 nm being the upper limit of the optical spectrum analyzer. The numerical analysis presented here is thus an essential part to overcome the severe limitation in measuring capabilities and to understand the phenomena of supercontinuum generation, which is mainly related to Raman self-frequency shift. Finally, this work demonstrates the potential of noise-like pulses from a passively mode-locked fiber laser for broadband spectrum generation.     

Laser diode end-pumped passively Q-switched Tm,Ho:YLF laser with Cr:ZnS as a saturable absorber

Output performance of a continuous-wave (CW) laser diode end-pumped passively Q-switched Tm,Ho:YLF laser is demonstrated with a Cr:ZnS crystal as the saturable absorber. We particularly investigate the influence of saturable absorber's position in the resonator when the Cr:ZnS crystal is placed close to and far from the laser beam waist. We compare the experimental results at the two different positions, and find that the laser shows unusual output characteristics when the Cr:ZnS saturable absorber is placed close to the beam waist. The pulse width and the pulse energy almost keep constant, measured about 1.25 μs and 4 μJ respectively, when the pump power is changed in the range of 1–1.9 W. Moreover, the pulse repetition frequency can be tuned between 1.3 kHz and 2.6 kHz by changing the pump power. The output wavelength of the passively Q-switched laser shifts to 2053 nm from 2067 nm in CW operation.     

Cascaded continuous-wave singly resonant optical parametric oscillator pumped by a single-frequency fiber laser

We present a cascaded continuous-wave singly resonant optical parametric oscillator (SRO) delivering idler output in mid-IR and terahertz frequency range. The SRO was pumped by an ytterbium-doped fiber laser with 27 W linear polarization pump powers, and based on periodically poled MgO:LiNbO₃ crystal (PPMgLN) in two-mirror linear cavity. The PPMgLN is 50 mm long with 29.5 μm period. The idler power output at 3811 nm was obtained 2.6 W. The additional spectral components that have been attributed to cascaded optical parametric processes are described at increasing pump levels. Besides the initial signal component at about 1476.8 nm, further generated wavelengths with frequency shifts about 47 cm^?1, 94 cm^?1 and 104 cm^?1 were observed. It was speculated that the idler waves lie in the terahertz (THz) domain from the observed results.     

High power single-longitudinal-mode Ho:YLF unidirectional ring laser based on a composite structure of acousto-optic device and wave plate

We report a unidirectional single-longitudinal-mode Ho:YLF ring laser. An acousto-optic modulator and two half-wave plates were used to enforce the Ho:YLF ring laser in a unidirectional operation. The single-longitudinal-mode output power could reach 3.73 W successfully when the incident pump power was 16.4 W. The corresponding slope efficiency was 27.1%. The wavelength of the single-longitudinal-mode Ho:YLF ring laser was 2063.8 nm. The M² factor was 1.12. The results illustrated that the single-longitudinal-mode output power could be further enhanced by increasing the radio frequency power of the acousto-optic modulator.     

Semiconductor type single wall carbon nanotube absorber for passive mode-locked Nd:YVO4 laser

The pure semiconductor type single wall carbon nanotubes (SWCNT) was transferred on hydrophilic glass substrate to fabricate saturable absorbers by vertical evaporation technique. The recovery time of the absorber is 350 fs. The saturation intensity of the absorber was found to be 115 μJ/cm² at 1060 nm. The modulation depth of the absorber could be about 7%. Passive mode-locked Nd:YVO₄ laser using this kind of absorber was demonstrated. The largest average output power of the mode-locked laser is 1.4 W at the pump power of 7.8 W. The continuous wave mode-locked pulses with the repetition of 80 MHz were achieved.     

980 nm Yb-doped double-clad photonic crystal fiber amplifier and its frequency doubling

In this paper, we report on a large-mode-area double-clad 980 nm Yb-doped photonic crystal fiber (PCF) amplifier. In the experiment, an output power of 1.21 W at 980 nm with 2.5 nm bandwidth has been yielded when the PCF length was 40 cm. Through frequency doubling the 980 nm amplified laser with a BIBO crystal, an output power of 51 mW at 490 nm has been generated.     

LD-end-pumped passively Q-switched Nd:YAG ceramic laser with single wall carbon nanotube saturable absorber

We report on a LD-end-pumped passively Q-switched Nd:YAG ceramic laser by using a novel single wall carbon nanotube saturable absorber (SWCNT-SA). The SWCNT wafer was fabricated by electric Arc discharge method on quartz substrate with absorption wavelength of 1064 nm. We firstly investigated the continuous wave (CW) laser performance and scattering properties of Nd:YAG ceramic sample. For the case of passively Q-switched operation, a maximum output power of 376 mW was obtained at an incident pump power of 8.68 W at 808 nm, corresponding to an optical–optical conversion efficiency of 4.3%. The repetition rate as the increase of pump power varied from 14 to 95 kHz. The minimum pulse duration of 1.2 μs and maximum pulse energy of 4.5 μJ was generated at a repetition rate of 31.8 kHz.     

High-power eye-safe KTA-OPO driven by YVO4/Nd:YVO4 composite laser

We present a high-power 1.53 μm laser based on intracavity KTA-OPO driven by diode-end-pumped acousto-optical Q-switched YVO₄/Nd:YVO₄ composite. The composite crystal was utilized for reducing the thermal effect, and the mode mismatch compensating OPO cavity was designed for efficient OPO conversion. The output power of eye-safe laser at 1535 nm was up to 4.4 W with the pump power of 27 W, corresponding to a diode-to-signal conversion efficiency of 16.3%. To our knowledge, this is the highest output power in diode-end-pumped circumstances. In the experiment, the strong yellow light generated by Raman conversion and frequency doubling in the KTA crystal was observed.     

A novel triple pump 1050 nm, 1400 nm, 800 nm pumping scheme for thulium doped fiber amplifier

Thulium doped fiber amplifier is a good candidate for S, and S+ band. This paper demonstrated a three pump pumping scheme for thulium doped fiber amplifier with 1050 nm co propagating pump and 1400 nm and 800 nm counter propagating pumps with a total pumping power 600 mW. This configuration yields up to 33 dB gain in 20 nm region from 1460 nm to 1480 nm, with noise figure <4 dB. To the knowledge of authors it is the highest gain achieved by thulium-doped amplifier in a single pass configuration with good power conversion efficiency.     

Continuous-wave 560 nm light generated by intracavity SrWO4 Raman and KTP sum-frequency mixing

An LD end-pumped Nd:YAG/SrWO₄ continuous-wave 560 nm laser is presented based on intracavity sum-frequency mixing of the fundamental and first-Strokes light. The maximum output power of 330 mW at 559.6 nm was obtained for the diode pump power of 13.7 W and the conversion efficiency was about 2.5%. The intense blue emission was also observed in the SrWO₄ crystal when the Raman laser was operating above threshold. This blue emission is centered at 473 nm, which also happened to YVO₄.     

Nanosecond-pulsed erbium-doped fiber lasers with graphene saturable absorber

We demonstrate graphene mode-locked nanosecond erbium-doped fiber laser in an all-fiber ring cavity. The clean and robust pulse train was generated at 27 mW pump power. Resultant central wavelength, repetition rate and pulse width was 1560 nm, 388 kHz and 6 ns, respectively. With two stage fiber amplifier, the output power was 553 mW, corresponding to single pulse energy of 1.4 μJ. In addition, the pulse-width can be varied ranging from 3 ns to 20 ns at repetition rate between 200 kHz and 1.54 MHz by changing the length of the laser cavity.