Theory and experiment of flat-top all-fiber comb filter based on two high birefringence fiber Sagnac loop filters

A simple flat-top all-fiber comb filter based on two high birefringence fiber (HBF) Sagnac loop filters is presented. The proposed flat-top comb filter consists of two HBF Sagnac loop filters with two polarization controllers (PCs) and a fiber circulator. According to the theoretical analysis, with proper settings of the polarization state of the PCs, the comb filter can realize flat-top passband and the channel spacing also can be switched when the comb filter is convex spectrum. The 0.3 dB bandwidth of the flat-top passband is 0.49 nm with a free spectral range of 1.4 nm. The maximum extinction ratio is nearly 20 dB. The comb filter with switchable channel spacing can be obtained from 0.7 nm to 1.4 nm.     

A linearly-polarized tunable Yb-doped fiber laser using a polarization dependent fiber loop mirror

A Ytterbium-doped linearly-polarized fiber laser is constructed with a polarization maintaining fiber Sagnac loop mirror. The fiber loop mirror made of polarization maintaining fiber coupler has a polarization dependent reflectivity, which provides the necessary polarization discrimination between the slow and fast axes. With a fiber Bragg grating written in normal polarization maintaining fiber as an output coupler, laser output of up to 5.6 W at 1070 nm is generated with a polarization extinction ratio of > 20 dB and an overall efficiency of 55%. The broadband polarization dependent reflection of the fiber loop mirror offers advantages of easy spectral tuning and simple linearly-polarized laser generation.     

Twist sensor based on Sagnac single-mode optic fiber interferometer

An optical fiber twist sensor based on Sagnac single-mode optic fiber interferometer is proposed. The stress-induced birefringence of single-mode optical fiber is obtained by applying a transverse force against a short length of singlemode fiber. A high sensitivity and resolution of the twist angle measurement of 0.19 nm/° and 0.002° is achieved experimentally, respectively. The proposed sensor is more convenient and simple than that of standard polarization-maintaining fibers.     

Design of hybrid photonic crystal fiber: Polarization and dispersion properties

A highly birefringent dispersion compensating hybrid photonic crystal fiber is presented. This fiber successfully compensates the chromatic dispersion of standard single mode fiber over E- to L-communication bands. Simulation results reveal that it is possible to obtain a large negative dispersion coefficient of about −1054.4 ps/(nm km) and a relative dispersion slope of 0.0036 nm⁻¹ at the 1550 nm wavelength. The proposed fiber simultaneously provides a high birefringence of order 3.45 × 10⁻² at the 1550 nm. Moreover, it is confirmed that the designed fiber successfully operates as a single mode in the entire band of interest. For practical conditions, the sensitivity of the fibers dispersion properties to a ±2% variation around the optimum values is carefully studied and the nonlinearity of the proposed fiber is also reported and discussed. Such fibers are essential for high speed transmission system as a dispersion compensator, sensing applications, fiber loop mirrors as well as maintaining single polarization, and many nonlinear applications such as four-wave mixing, etc.     

Ultra-broad and flat supercontinuum generation in short photonic crystal fiber combined with conventional fibers

In order to gain ultra-broad and flat super-continuum (SC) spectrum, we propose and demonstrate a new scheme. By coupling a train of short pulses with 100 fs width and 16.2 mW average power generated by a mode-locked laser into the scheme – short photonic crystal fiber (PCF) combined with conventional fibers. The SC spectrum has 491 nm bandwidth at −15 dBm below the spectral peak with ±0.5 dBm uniformity 100 nm in only 0.45 m PCF. The spectral bandwidth generated in the scheme increases 292 nm than spectrum generated in the two conventional fibers, and increases 152 nm than spectrum generated in the three convention fibers.     

Remote and high precision step height measurement with an optical fiber multiplexing interferometric system

An optical fiber multiplexing low coherence and high coherence interferometric system, which includes a Fizeau interferometer as the sensing element and a Michelson interferometer as the demodulating element, is designed for remote and high precision step height measurement. The Fizeau interferometer is placed in the remote field for sensing the measurand, while the Michelson interferometer which works in both modes of low coherence interferometry and high coherence interferometry is employed for demodulating the measurand. The range of the step height is determined by the low coherence interferometry and the value of it is measured precisely by the high coherence interferometry. High precision has been obtained by searching precisely the peak of the low coherence interferogram symmetrically from two sides of the low coherence interferogram and stabilizing the Michelson interferometer with a feedback loop. The maximum step height that could be measured is 6 mm while the measurement resolution is less than 1 nm. The standard deviation of 10 times measurement results of a step height of 1 mm configurated with two gauge blocks is 0.5 nm.     

Temperature and strain discrimination using two parallel connected Sagnac loops based on character-1 shaped polarization-maintaining fiber

A fiber sensor configuration suitable for discrimination of temperature and strain is presented. The sensor head is composed of two parallel concatenated Sagnac loops based on character-1 shaped polarization-maintaining fiber (PMF). The two Sagnac loops include different sections of character-1 shaped PMFs, and show different sensitivity to temperature and strain. By monitoring the wavelength shift of the two dips in the transmission spectrum, simultaneous measurement of temperature and strain is obtained. The sensitivity for strain and temperature are measured to be 14.46 pm and ? 0.54 nm.     

Er/Yb co-doped fiber amplifier with wavelength-tuned Yb-band ring resonator

Erbium-ytterbium co-doped fiber amplifier with wavelength-tuned Yb-band loop resonator is presented. The amplified spontaneous emission (ASE) from Yb ions is utilized to stimulate a laser emission at several wavelengths from the 1 μm band in the 1550 nm amplifier. The wavelength of this lasing is tuned by introducing a fiber Bragg grating (FBG). The results show, that the overall efficiency of the amplifier at nominal 1550 nm wavelength can be increased by introducing a feedback loop with 1040 nm and 1050 nm FBG. This loop also protects the Er/Yb amplifier from parasitic lasing at 1 μm and allows significant output power scaling without risk of self-pulsing.     

All fiber passively mode locked zirconium-based erbium-doped fiber laser

All passively mode locked erbium-doped fiber laser with a zirconium host is demonstrated. The fiber laser utilizes the Non-Linear Polarization Rotation (NPR) technique with an inexpensive fiber-based Polarization Beam Splitter (PBS) as the mode-locking element. A 2 m crystalline Zirconia–Yttria–Alumino-silicate fiber doped with erbium ions (Zr–Y–Al-EDF) acts as the gain medium and generates an Amplified Spontaneous Emission (ASE) spectrum from 1500 nm to 1650 nm. The generated mode-locked pulses have a spectrum ranging from 1548 nm to more than 1605 nm, as well as a 3-dB bandwidth of 12 nm. The mode-locked pulse train has an average output power level of 17 mW with a calculated peak power of 1.24 kW and energy per pulse of approximately 730 pJ. The spectrum also exhibits a Signal-to-Noise Ratio (SNR) of 50 dB as well as a repetition rate of 23.2 MHz. The system is very stable and shows little power fluctuation, in addition to being repeatable.     

Design of a highly nonlinear twin bow-tie polymer photonic quasi-crystal fiber with high birefringence

A twin bow-tie polymer-based photonic quasi-crystal fiber with high birefringence, high nonlinearity and low dispersion as well as maintaining single mode operation is presented in the wavelength range 1.8–2.2 μm. Through optimizing fiber structure parameter using a full-vector finite-element method combined with perfectly matched layers boundary condition, the birefringence is as high as 2.43 × 10⁻³, the nonlinearity is as high as 118 W⁻¹ km⁻¹, and the dispersion is only 25 ps/nm/km at 2 μm with the holes pitch of 3.3 μm. From the point of fabrication, the influences of deviation of each air hole diameter are discussed to verify the robustness of the photonic quasi-crystal fiber designed.     

High speed ultra short pulse fiber ring laser using photonic crystal fiber nonlinear optical loop mirror

A scheme to generate high speed optical pulse train with ultra short pulse width is proposed and experimentally studied. Two-step compression is used in the scheme: 20 GHz and 40 GHz pulse trains generated from a rational harmonic actively mode-locked fiber ring laser is compressed to a full width at half-maximum (FWHM) of ~ 1.5 ps using adiabatic soliton compression with dispersion shifted fibers (DSF). The pulse trains then undergo a pedestal removal process by transmission through a cascaded two photonic crystal fiber (PCF)-nonlinear optical loop mirrors (NOLM) realized using a double-ring structure. The shortest output pulse width obtained was ~ 610 fs for 20 GHz pulse train and ~ 570 fs for 40 GHz pulse train. The signal to noise ratio of the RF spectrum of the output pulse train is larger than 30 dB. Theoretical simulation of the NOLM transmission is conducted using split-step Fourier method. The results show that two cascaded NOLMs can improve the compression result compared to that for a single NOLM transmission.     

Dual-wavelength narrow-linewidth fiber laser based on F-P fiber ring filter

A dual-wavelength fiber laser with a narrow-linewidth, based on a P-F fiber filter has been proposed. Polarization-maintaining fiber Bragg grating (PM-FBG) and a F-P fiber filter are introduced based on the traditional fiber laser. PM-FBG is used as the wavelength selection device. The fiber F-P filter consists of two optical couplers and a section of un-pumped erbium-doped fiber (EDF). Due to the delay of cavity and the loss generated by the EDF, the filter has comb spectral response. The incorporation of the fiber F-P filter leads to the suppression of undesirable modes. At the room temperature, under 980 nm LD pumped, the maximum output of the two wavelengths is respectively ?2.259 dBm and 0.568 dBm, with the 3-dB bandwidth separately 0.1 nm and 0.14 nm, realizing the narrow linewidth and dual-wavelength output.     

980 nm Yb-doped double-clad photonic crystal fiber amplifier and its frequency doubling

In this paper, we report on a large-mode-area double-clad 980 nm Yb-doped photonic crystal fiber (PCF) amplifier. In the experiment, an output power of 1.21 W at 980 nm with 2.5 nm bandwidth has been yielded when the PCF length was 40 cm. Through frequency doubling the 980 nm amplified laser with a BIBO crystal, an output power of 51 mW at 490 nm has been generated.     

Large-range liquid level sensor based on an optical fibre extrinsic Fabry–Perot interferometer

We propose an efficient approach to develop large-range liquid level sensors based on an extrinsic Fabry–Perot optical fibre interferometer with an all fused-silica structure and CO₂ laser heating fusion bonding technology. The sensor exhibits signatures of a high sensitivity of 5.3 nm/kPa (36.6 nm/psi), a resolution of 6.8 Pa (9.9×10⁻⁴ psi) and an extreme low temperature dependence of 0.013 nm/°C. As a result, a high resolution of the water level measurement of approximately 0.7 mm on the length scale of 5 m and small errors of the water pressure measurement induced by the temperature dependence within 0.0025 kPa/°C (0.00036 psi/°C, water level 0.25 mm/°C) are achieved, thus providing useful applications for the detection of the large-range liquid level in harsh environments.     

Broadband and low amplitude noise supercontinuum generated by using compressed pulse

In this paper, enhancement of bandwidth of supercontinuum generated in a normal dispersion-flattened microstructured fiber by using compressed pulse is demonstrated experimentally and numerically. Using high-order soliton compression effect, the standard single mode fiber is used as a pulse compressor. The experimental measured ?10 dB spectral width is broadened from 75 nm to more than 140 nm by adding a 20 m long standard single mode fiber. Numerical analysis shows that using pulse compressed by a certain length fiber can increase the spectral bandwidth without making extra amplitude noise.     

Carbon fiber formation in electrical discharges in hydrocarbons

The process of synthesis of carbon fiber from hydrocarbon vapours in low-current electrical-discharge plasma was investigated in the paper. The carbon fibers were effectively synthesised in discharge of positive polarity generated between a stainless steel needle and a plate made of nickel alloy, for the discharge current ranged from 1 mA up to 3 mA. The experiments were carried out at normal pressure in cyclohexane vapours with argon as carrier gas. The diameter of produced fibers varied from about 20 to 70 μm. The growth rate of the fiber was about 0.25 mm/s.     

Novel UV-emitting single crystalline film phosphors grown by LPE method

This work reports the development of new types of UV-emitting phosphors based on single crystalline films (SCF) of aluminum garnet and perovskite compounds grown by the liquid phase epitaxy method. We consider peculiarities of the growth and the luminescent and scintillation properties of the following four types of UV SCF phosphors: i) Ce-doped SCF of Y–Lu–Al-perovskites with the Ce³⁺ emission in the 300-450 nm range of the decay time of 16–17 ns; ii) Pr-doped SCF of Y–Lu–Al garnets and perovskites with the Pr³⁺ emission in the 300–400 nm and 235–330 nm ranges with the decay time of 13–19 and 7–8 ns, respectively; iii) La³⁺ or Sc³⁺ doped SCF of Y–Lu–Al-garnets, emitting in the 280-400 nm range due to formation of the La_Y,Lu, Sc_Y,Lu and Sc_Al centers with decay time of the order of several hundreds of nanoseconds; iv) Bi³⁺ doped SCF of garnets with Bi³⁺ emission in 275–350 nm with decay time of about 1.9 μs.     

Numerical analysis of a broadband spectrum generated in a standard fiber by noise-like pulses from a passively mode-locked fiber laser

This paper covers a numerical analysis of supercontinuum spectrum generation in a piece of standard fiber by using as the pump noise-like pulses produced by a passively mode-locked fiber laser. An experimental study was also carried out, yielding results that support the numerical results. In the numerical study we estimated that the spectral extension of the generated supercontinuum reaches ~ 1000 nm, and that it presents a high flatness over a region of ~ 220 nm (1630 nm-1850 nm) when we use as the pump noise-like pulses with a wide optical bandwidth (~ 50 nm) and a peak power of ~ 2 kW. Experimentally, the output signal spectrum extends from ~ 1530 nm to at least 1750 nm and presents a high flatness over a region of 1640 nm to 1750 nm for the same value of numerical input power, 1750 nm being the upper limit of the optical spectrum analyzer. The numerical analysis presented here is thus an essential part to overcome the severe limitation in measuring capabilities and to understand the phenomena of supercontinuum generation, which is mainly related to Raman self-frequency shift. Finally, this work demonstrates the potential of noise-like pulses from a passively mode-locked fiber laser for broadband spectrum generation.     

Temperature sensing using the spectral interference of polarization modes in a highly birefringent fiber

The spectral interference of polarization modes in a highly birefringent (HB) fiber to measure temperature is analyzed theoretically and experimentally. A tandem configuration of a birefringent delay line and a sensing HB fiber is considered and the spectral interferograms are modelled for the known birefringence dispersion of the HB fiber under test. As the delay line, a birefringent quartz crystal of a suitable thickness is employed to resolve a channeled spectrum. The channeled spectra are recorded for different temperatures and the polarimetric sensitivity to temperature, determined in the spectral range from 500 to 850 nm, is decreasing with wavelength. It is demonstrated that the temperature sensing is possible using the wavelength interrogation, i.e., the position of a given interference maximum is temperature dependent. The temperature sensitivity of the HB fiber under test is −0.25 nm/K and the resolution is better than 0.5 K.     

Simple air-gap fiber Fabry–Perot interferometers based on a fiber endface with Sn-microsphere overlay

This study presents a simple, cost-effective and sensitive air-gap fiber Fabry–Perot interferometer (AG-PPFI) which is based on a metal Tin (Sn)-overlaying fiber technique. An extremely small drop of metallic Sn was heated and then melted to shrink into a microsphere owing to the cohesion of the material. When a fiber was inserted into the melting Sn microsphere, an air gap was naturally formed between the fiber endface and the metal Sn during the cooling process. By carefully controlling the reaction time, various air-gaps can be formed as the Fabry–Perot interferometric cavities for the proposed AG-PPFIs. Measurements reveal that a smaller length of air-gap and heavier mass of Sn-microsphere are associated with higher sensitivity of temperature, but the former is dominated. A best temperature sensitivity of wavelength shift with +4.3 nm/°C is achieved when the air-gap is about 5 μm with mass of Sn-microsphere of about 10 μg. The variation of the wavelength shift is equivalent to sensitivity for a change in the cavity length of +14.83 nm/°C.