Coherent crosstalk in passive microring based Optical Networks-on-Chip

Optical Networks-on-Chip (ONoC) is emerging technology for future optical interconnects used in all optical networks. The electrical interconnects face lot of problems due to their inability to support higher data rates used in the System-on-Chip (SoC) technologies. Integrated optical interconnects based on SoC avoid this bottleneck with their support to higher data rates. In this paper for the first time we have studied and analyzed ONoC at physical level for the system performance based on crosstalk, BER, throughput, system frequency, and other related parameters. The investigation of ONoC performance is carried out for the multistage microring optical crossconnect on SoC for coherent WDM signals. The analysis can be used in the design of ultra-high speed photonic routers for reliable data communication and processing. The results show the dependency of a coherent crosstalk on the system frequency of SoC and also illustrate the reduction in throughput with increase in number of WDM signals due to higher probability of packet transmission. Minimum 2 dB signal to noise ratio can be obtained when crosstalk is ?25 dB with 60 wavelengths for probability of packet transmission is 0.5.     

光互联网的抗毁性设计研究

由于互联网层叠模型中多层都存在重复的保护与恢复机制，致使互联网的实现极其复杂，造成网络传输效率较低，而且拥塞。随着密集波分复用（DWDM）的广泛使用和网络底层性能的大幅度提高，已经不需要再对网络中多层进行重复保护与恢复。在此基础上，采用了未来光互联网3层 (应用层、IP层和光互联层) 协议模型，并对其中的光互联层的保护进行了深入的研究，提出了部分共享备用路径保护(P-SPP)方法。此模型能充分利用IP层电子的灵活恢复机制与光互联层的快速保护与恢复机制，提高光互联网的传输性能，以适应目前高速发展的互联网对传输带宽的要求。     

An efficient fault localization or detection mechanism for high speed optical networks

Optical burst switching (OBS) has been considered as the gate through which the envisaged world of optical Internet will be conquered by implementing Internet Protocol (IP) software directly over a wavelength-division-multiplexing (WDM) optical layer (IP/WDM). The main feature for designing next generation optical networks is protecting and restoring high capacity WDM networks from the failures. Quick detection, identification and restoration make networks more strong and consistent even though the failures cannot be avoided. Hence, it is necessary to develop fast, efficient and dependable fault localization or detection mechanisms. In this paper, an efficient scheme for OBS networks has been proposed to provide fast restoration of links with minimum delay as well as blocking probability. By simulation results, it is shown that the proposed OBS scheme achieve less blocking probability and delay while getting higher throughput in comparison to conventional schemes.     

Impact of thermal effect on reliability in Optical Network-on-Chip

Emerging advances in silicon nanophotonics have driven optical interconnect to be a promising method for intra-chip multi-core system. Optical Network-on-Chip (ONoC) can provide high throughput and low latency compared with traditional electrical ones. However, on-chip thermal effect is an inherent characteristic and chip temperature can fluctuate spatially, which can affect the operation of silicon nanophotonic devices. This leads to an influence on the reliability of communication. This article analyzes the influence of thermal effect on reliability of communication based on the temperature profile in ONoC, showing the relationship between power consumption and thermal effect, as well as the influence of thermal effect on the reliability of communication. We reveal the primary cause of the thermal effect in ONoC and the important factors of the influence on SNR, in order to minimize the thermal impacts and improve the reliability of ONoC in the further study.     

IP/WDM网络的集成服务质量(QoS)控制方法

对IP/WDM网络的集成服务质量（QoS）控制技术问题做了研究, 给出了基于通用多协议标记交换（GMPLS）技术的业务差分处理模型, 设计了新的业务分类、光路分类以及层间映射/疏导/重构策略, 给出了具体的映射技术方案. 本方法具有三大特点：1）光电集成的差分服务模型; 2）多粒度多优先级业务的自适应资源管理机制; 3）支持电信级应用. 该模型较好地折中了多种类型业务的QoS控制复杂性和有效性, 具有较强的实用性和可扩展性, 能够解决光因特网络中支持多媒体业务传送的QoS问题.     

Design and performance evaluation of a metro WDM storage area network with IP datagram support

Storage area networks (SANs) are becoming an important part of optical MANs (metropolitan area networks). Growing storage and business-continuity needs; high-bandwidth, low latency requirements for SANs; storage infrastructure consolidation; and post-9/11 regulatory issues are among the several driving factors to push this trend. We, in this paper, consider a metro wavelength division multiplexing (WDM) SAN that allows the transmission of variable packet size such as Internet protocol (IP) datagram and evaluate its performance by means of discrete-event simulation. The network is based on one fixed transmitter and multiple fixed receivers. Beginning with an introduction and the context of this work, we describe the network and node architectures; and introduce the medium access control (MAC) protocols. Subsequently, using the Poisson and self-similar traffic, we present and discuss performance of the proposed network architecture in terms of throughput and queuing delay under symmetric and asymmetric traffic scenarios. The simulation results suggested that the proposed architecture is suitable for SAN applications which demand low queuing delay and high throughput.     

多色焦平面和图像融合SoC实现技术的研究

大规模、智能化的多色焦平面阵列探测器和高性能、高集成度的SoC技术是未来发展的方向。对多色焦平面的概况、发展和关键技术进行了分析。为了能够更有效的利用信息,把由多色焦平面探测器输出的,并经天然配准的各波段图像进行了融合处理。详细介绍了现有的多种图像融合算法、模型、SoC和高速处理硬件平台的研究情况以及若干新进展。     

Full-range tunable optical delay line based on coupled and side-coupled resonators

An optical delay line based on a new kind of structure comprising coupled resonators and side-coupled resonators has been proposed and demonstrated. The structure has unique advantages in realizing tunable optical delay lines. The tuning range has covered almost the full range of the optical delay line, from minimum delay at which only one ring of the light pulse structure requires transmission, to maximum delay at which all rings are required. In addition, the input signal delivered from the input to output port travels the structure twice, thereby providing buffer delay that is twice longer than general coupled resonators.     

Beam-splitting ball lens: a new integrated optical component

A beam-splitting ball lens is introduced as a new integrated optical component for board- and backplane-level optical interconnection applications. The proposed beam-splitting ball lenses can be used in conjunction with polymer fiber image guides to split and combine imaged patterns of two-dimensional array optical data. Power and resolution performance parameters of a packaged system are presented.     

High-performance unidirectional electrooptic modulator based on polymeric highly multi-mode waveguides

A unidirectional electrooptic modulator based on an asymmetrical highly multi-mode waveguide coupler is proposed. Firstly, the energy distributions of all the modes within two highly multi-mode waveguides are analyzed with eigenstate theory. Then, to achieve high switching performance in a guided-wave coupler, a dumping wall is placed on the larger waveguide of an asymmetric pair of waveguides, so that the larger waveguide has a dumping effect. This dumping effect makes the asymmetric highly multi-mode waveguide coupler possess a highly efficient unidirectional coupling process. Due to the large cross-section of the waveguide, a new modulation electrode structure is built. Based on this dumping effect, the unidirectional coupling process is theoretically modeled. Furthermore, in both scenarios, i.e., the unmodulated state and the electrooptically modulated state, the unidirectional coupling efficiencies are studied. As a result, not only can a high unidirectional coupling efficiency of 100% be achieved, but a high electrooptic modulation depth more than 90% can also be implemented in theory, and a high thermooptic modulation depth more than 90% under a low modulation voltage of 30 volts is also experimentally achieved. This device can be used for multi-mode optical interconnection systems such as data communication and fiber sensor networks.     

50 GHz optical true time delay beamforming in hybrid optical/mm-wave access networks with multi-core optical fiber distribution

We propose and experimentally validate an optical true time delay beamforming scheme with straightforward integration into hybrid optical/millimeter(mm)-wave access networks. In the proposed approach, the most complex functions, including the beamforming network, are implemented in a central office, reducing the complexity and cost of remote antenna units. Different cores in a multi-core fiber are used to distribute the modulated signals to high-speed photodetectors acting as heterodyne mixers. The mm-wave carrier frequency is fixed to 50 GHz(VBand), thereby imposing a progressive delay between antenna elements of a few picoseconds. That true time delay is achieved with an accuracy lower than 1 ps and low phase noise.     

Electrical considerations for interconnections inside a computer

In this paper we discuss the electrical and physical properties of interconnection structures that impact the performance of computer systems. These considerations are illustrated with three examples of such devices found in a typical mainframe. The requirements for the future are then presented. The ability of new technologies, electrical and optical, for satisfying these requirements is discussed.     

Adiabatically tunable optical delay lines and their performance limitations

A simple tunable optical delay line based on adiabatic zone folding in coupled resonator lines is proposed, and its performance is analyzed. The results, valid for all adiabatically tunable optical buffers based on resonators, indicate that, while at low to medium bit rates the performance is improved substantially compared with that of the fixed delay lines, this improvement vanishes for high bit rates and large storage capacities.     

Low-distortion hybrid optical shuffle concept

A hybrid micro-macro-optical shuffle interconnection approach is described. The new concept minimizes distortion in multichip smart-pixel shuffle interconnection systems that use macro-optics to link dense arrays of vertical-cavity surface-emitting laser (VCSEL) sources and matching arrays of detectors. The typical narrow-beam cones of VCSEL's are exploited by use of beam-deflecting micro-optics to create an optical system that is symmetric about its aperture. Since symmetric systems are well known to cancel distortion, this novel concept provides the means to achieve the required high degree of interchip registration accuracy.     

Silicon microring-based signal modulation for chip-scale optical interconnection

Electro-optic modulation plays a critical role in implementing space-, power- and spectrally efficient optical interconnection for high-capacity computing systems. Microring resonators exhibit a great potential to achieve compact, low power-consumption and high-speed modulators. In this paper, we briefly review our efforts on designing and analyzing the microring modulators. Three types of single-ring modulators are discussed, from device behavior to possible system impact. We then present two novel double-ring modulators in which a passive ring resonator is added, enabling higher operation speed and lower power consumption. We also describe an opportunity of introducing phase modulation data formats into the on-chip communication environment. In this paper, our emphasis is placed on linking the devices’ physics to their system performance and providing potential technical solutions to physical-layer challenges of optical interconnection.     

A multilevel nano-scale interconnection RLC delay model

Based on the multilevel interconnections temperature distribution model and the RLC interconnection delay model of the integrate circuit,this paper proposes a multilevel nano-scale interconnection RLC delay model with the method of numerical analysis,the proposed analytical model has summed up the influence of the configuration of multilevel interconnections,the via heat transfer and self-heating effect on the interconnection delay,which is closer to the actual situation.Delay simulation results show that the proposed model has high precision within 5% errors for global interconnections based on the 65 nm CMOS interconnection and material parameter,which can be applied in nanometer CMOS system chip computer-aided design.     

一种新的生物医学用快速实时低相干显微成象原理

本文讨论了一种将共焦显微术与迈克耳逊干涉术相结合,并利用宽带低相干光源相干长度短的特点而形成的一种可对高密度非透明样品进行显微成象的方法,并将这种显微成象方法与共焦显微成象方法进行了比较,最后讨论了一种快速实时成象的原理,基于这种原理设计的仪器将为生物和医学工作者提供一种新的非侵入测量和诊断手段.     

Research on Optical Transmitter and Receiver Module Used for High-Speed Interconnection between CPU and Memory

With the development of the multicore processor, the bandwidth and capacity of the memory, rather than the memory area, are the key factors in server performance. At present, however, the new architectures, such as fully buffered DIMM (FBDIMM), hybrid memory cube (HMC), and high bandwidth memory (HBM), cannot be commercially applied in the server. Therefore, a new architecture for the server is proposed. CPU and memory are separated onto different boards, and optical interconnection is used for the communication between them. Each optical module corresponds to each dual inline memory module (DIMM) with 64 channels. Compared to the previous technology, not only can the architecture realize high-capacity and wide-bandwidth memory, it also can reduce power consumption and cost, and be compatible with the existing dynamic random access memory (DRAM). In this article, the proposed module with system-in-package (SiP) integration is demonstrated. In the optical module, the silicon photonic chip is included, which is a promising technology to be applied in the next-generation data exchanging centers. And due to the bandwidth–distance performance of the optical interconnection, SerDes chips are introduced to convert the 64-bit data at 800 Mbps from/to 4-channel data at 12.8 Gbps after/before they are transmitted though optical fiber. All the devices are packaged on cheap organic substrates. To ensure the performance of the whole system, several optimization efforts have been performed on the two modules. High-speed interconnection traces have been designed and simulated with electromagnetic simulation software. Steady-state thermal characteristics of the transceiver module have been evaluated by ANSYS APLD based on finite-element methodology (FEM). Heat sinks are placed at the hotspot area to ensure the reliability of all working chips. Finally, this transceiver system based on silicon photonics is measured, and the eye diagrams of data and clock signals are verified.     

基于正交化算法的三值互连神经网络模型

提出了以信息损失最少为原则的三值(±1)互连权重编码方法，这种编码方法比以前的三值权重编码方法显著地提高了神经网络的性能。由于互连权重只有三值，恰恰弥补了光互连精度不高的缺点，易于光学实现。     

Investigation on performance of all optical buffer with large dynamical delay time based on cascaded double loop optical buffers

Optical buffers are critical for optical signal processing in future optical packet-switched networks. In this paper, a theoretical study as well as an experimental demonstration on a new optical buffer with large dynamical delay time is carried out based on cascaded double loop optical buffers (DLOBs). It is found that pulse distortion can be restrained by a negative optical control mode when the optical packet is in the loop. Noise analysis indicates that it is feasible to realise a large variable delay range by cascaded DLOBs. These conclusions are validated by the experiment system with 4-stage cascaded DLOBs. Both the theoretical simulations and the experimental results indicate that a large delay range of 1-9999 times the basic delay unit and a fine granularity of 25 ns can be achieved by the cascaded DLOBs. The performance of the cascaded DLOBs is suitable for the all optical networks.