Novel 60 GHz RoF system with optical single sideband mm-wave signal generation and wavelength reuse for uplink connection

In order to improve RF frequency to achieve higher bandwidth and larger capacity, we propose a novel scheme to generate optical single sideband (SSB) millimeter-wave, in which frequency doubling of local radio frequency (RF) is obtained by using one integrated Mach–Zehnder modulator (MZM), and we theoretically investigate the generating principle of SSB. The optical SSB modulation scheme is employed to generate 60 GHz optical mm-wave and the 2.5 Gb/s baseband signal is simultaneously up-converted at the central station (CS) for downlink transmission, and the optical carrier is reused for uplink connection at the base station (BS). The full-duplex 2.5 Gb/s data are successfully transmitted over 40 km standard single-mode fiber (SMF-28) for both uplink connection and downlink connection with less than 2-dB power penalty. Results show the novel 60 GHz RoF system with optical SSB mm-wave signal generation using optical frequency doubling is feasible and we can obtain simple cost-efficient configuration and good performance over long-distance transmission.     

Sub-THz continuous wave generation scheme using high-order harmonics modulated lightwave

We propose a sub-THz continuous wave (CW) generation scheme using a high-order harmonics modulated lightwave (HML) to reduce an electronic dependency of a conventional double sideband suppressed carrier (DSB-SC) scheme. The electronic dependency should be overcome to increase frequency tunability of the conventional DSB-SC scheme. This is because the frequency of a local oscillator (LO), f_LO, should be one-half frequency of the frequency of a desired sub-THz CW in the conventional DSB-SC scheme. The proposed scheme is formed by adding an optical feedback loop to the conventional DSB-SC scheme. In order to verify our proposed scheme, a 120 GHz CW is generated using the LO with f_LO = 20 GHz. Based on our experimental results, we have found that the frequency of the LO can be reduced by our proposed scheme up to one-sixth (20 GHz) of 120 GHz. The 120 GHz CW generated by the proposed scheme has 52 dB higher photomixed output power with narrow spectral linewidth than that of the 120 GHz CW generated by the conventional DSB-SC scheme using the LO with f_LO = 20 GHz. Consequently, our proposed scheme can be helpful to reduce the electronic dependency of the conventional DSB-SC scheme.     

A novel proposal for DWDM demultiplexer design using modified-T photonic crystal structure

We propose an ultra compact structure to realize demultiplexing operation for Dense Wavelength Division Multiplexing (DWDM) communication systems using resonant cavity in modified-T Photonic Crystal (PC) structure. To the best of our knowledge, this is for the first time that a PC-based demultiplexer has been achieved with 1 nm channel spacing and 0.45 nm mean value of bandwidth without using either specific materials or complexities in fabrication process. Designs offering improvement of channel spacing and bandwidth of the proposed demultiplexer is our aim in this work. The attained characteristics are approximately in the range of the DWDM communication systems. Accurate resonant cavities have been used in terms of location and size of holes in the proposed structure in order for them to capture desired wavelengths in optical telecommunication range. Our simulations indicate the average amount of crosstalk (Xt) and the average quality factor (Q) to be ?21.1 dB and 3488, respectively. Two-dimensional (2D) Finite-Difference-Time-Domain (FDTD) is chosen for simulation of the proposed structure. The footprint of the structure is approximately 536 μm² and can be fabricated and integrated densely and easily.     

An 80 Gbps multi-band access radio over fiber link with single side band optical millimeter-wave dispersion-tolerant transmission without FBG and optical filter

We are presenting a new low-cost Single Sideband (SSB) modulated Radio-over Fiber (RoF) communication system for millimeter (mm)-wave multiband wireless communication at the frequencies of 40 GHz, 80 GHz and 120 GHz. Its principle lies in the Carrier Suppressed modulation through a nested dual electrode Mach–Zehnder Modulator (MZM) and product modulator based baseband signal decomposition. In this novel method, the optical signal is decomposed into different SSB signals using a power splitter and product modulators at the base station. This proposed method uses a different technique for a baseband signal decomposition from the existing method. The proposed signal decomposition technique has reduced the nonlinearities due to the FBGs. The proposed method is compared with the existing method in terms of BER, data rate and OSNR. The simulation results disclose that our proposed scheme outperforms the existing methods at a higher data rate of 80 Gbps with a minimum BER and privileged Q factor.     

Coupled frequency-doubling optoelectronic oscillator based on polarization modulation and polarization multiplexing

A coupled frequency-doubling optoelectronic oscillator (OEO) is proposed and experimentally demonstrated, which is constructed based on the perfect combination of polarization modulation and polarization multiplexing. A fundamental microwave signal at 9.95 GHz or a frequency-doubled microwave signal at 19.9 GHz is generated with a wavelength-independent sidemode-suppression ratio (SMSR) as high as 78 dB obtained. The phase noise of the generated 19.9-GHz signal is ? 103.45 dBc/Hz at 10-kHz frequency offset, indicating a good short-term stability. The proposed scheme is simple and flexible, which can find applications in radars and wireless communications.     

High speed ultra short pulse fiber ring laser using photonic crystal fiber nonlinear optical loop mirror

A scheme to generate high speed optical pulse train with ultra short pulse width is proposed and experimentally studied. Two-step compression is used in the scheme: 20 GHz and 40 GHz pulse trains generated from a rational harmonic actively mode-locked fiber ring laser is compressed to a full width at half-maximum (FWHM) of ~ 1.5 ps using adiabatic soliton compression with dispersion shifted fibers (DSF). The pulse trains then undergo a pedestal removal process by transmission through a cascaded two photonic crystal fiber (PCF)-nonlinear optical loop mirrors (NOLM) realized using a double-ring structure. The shortest output pulse width obtained was ~ 610 fs for 20 GHz pulse train and ~ 570 fs for 40 GHz pulse train. The signal to noise ratio of the RF spectrum of the output pulse train is larger than 30 dB. Theoretical simulation of the NOLM transmission is conducted using split-step Fourier method. The results show that two cascaded NOLMs can improve the compression result compared to that for a single NOLM transmission.     

A filterless optical millimeter-wave generation based on frequency octupling

A novel method of a filterless optical millimeter-wave (MMW) signal generation with frequency octupling using four nested Mach–Zehnder modulators (MZMs) is proposed for Radio-over-fiber systems. By symmetrically biasing the MZMs and using two RF driving signals with 90 deg phase delay, a cost-effective, high-quality and filterless optical millimeter-wave at 80 GHz with an optical harmonic distortion suppression ratio exceeding 40 dB is obtained. The proposed system is insensitive to the MZM bias drift, which demonstrates a relatively higher stability. So it is a viable solution for the future ultra-high frequency MMW applications.     

Novel attributes of AlGaN/AlN/GaN/SiC HEMTs with the multiple indented channel

In this paper, a high performance AlGaN/AlN/GaN/SiC High Electron Mobility Transistor (HEMT) with the multiple indented channel (MIC-HEMT) is proposed. The main focus of the proposed structure is based on reduction of the space around the gate, stop of the spread of the depletion region around the source–drain, and decrement of the thickness of the channel between the gate and drain. Therefore, the breakdown voltage increases, meanwhile the elimination of the gate depletion layer extension to source/drain decreases the gate–source and gate–drain capacitances. The optimized results reveal that the breakdown voltage and the drain saturation current increase about 178% and 46% compared with a conventional HEMT (C-HEMT), respectively. Therefore, the maximum output power density is improved by factor 4.1 in comparison with conventional one. Also, the cut-off frequency of 25.2 GHz and the maximum oscillation frequency of 92.1 GHz for the MIC-HEMT are obtained compared to 13 GHz and 43 GHz for that of the C-HEMT and the minimum figure noise decreased consequently of reducing the gate–drain and gate–source capacitances by about 42% and 40%, respectively. The proposed MIC-HEMT shows a maximum stable gain (MSG) exceeding 24.1 dB at 3.1 GHz which the greatest gain is yet reported for HEMTs, showing the potential of this device for high power RF applications.     

A long-reach WDM passive optical network enabling broadcasting service with centralized light source

We propose a long-reach wavelength-division-multiplexed (WDM) passive optical network (PON) to provide conventional point-to-point (P2P) data and downstream broadcasting service simultaneously by superimposing, for each WDM channel, the differential-phase-shift-keying (DPSK) broadcasting signal with the subcarrier multiplexing (SCM) modulated downstream P2P signal, at the optical line terminal (OLT). In the optical network units (ONUs), by re-modulating part of the downstream signal with a reflective semiconductor optical amplifier (RSOA), we realize color-less ONUs for upstream data transmission. The proposed scheme is numerically verified with a 5 Gb/s downstream P2P signal and broadcasting services, as well as 2.5 Gb/s upstream data through a 60 km bidirectional fiber link. In particular, the influence of the downstream lightwave's optical carrier–subcarrier ratio (OCSR) on the system performance is also investigated.     

CMOS—compatible reconfigurable microring demultiplexer with doped silicon slab heater

We present a 1×4 reconfigurable demultiplexer based on cascaded silicon microring resonators. The device is fabricated on a 0.18 μm complementary metal oxide semiconductor (CMOS) process. A homogeneous doped silicon slab heater is proposed and fabricated directly on the slab region of the microring resonator for thermal tuning. The flows of the heating currents in the heaters are parallel to the ring waveguide through the heavily doped slab regions located on both sides of the ring waveguide without through the waveguide core regions. The proposed doped heaters are experimentally verified with low-voltage operation and tuning efficiency of ～77 pm/mW. Without any tuning or trimming, predicted average channel spacing distribution in the whole free spectral range (FSR) is demonstrated. Full reconfigurability is also demonstrated in the demultiplexer with channel spacing of 2 nm (250 GHz) and 1 nm (125 GHz), corresponding to channel isolation of less than ?21 dB and ?16 dB, respectively. Such a low-voltage operation and reconfigurable demultiplexer is suitable for on-chip optical interconnect.     

Single tone and multi tone microwave over fiber communication system using direct detection method

In this paper, an analog microwave over fiber link for long haul distance based upon Rate Equation Laser is demonstrated. This system uses the advantage of high potential bandwidth of fiber in transmission of microwave signal. The interface of the two systems needs an up-conversion of microwave band into baseband (at which fiber operates). An Intensity Modulation Direct Detection (IMDD) technique is used to achieve this purpose. The Rate Equation laser is operated in a dynamic state, where its intensity oscillates at a microwave frequency that varies with the input signal fed by wave generator. This system can also use for two modulating tones. The frequency of the first tone is varied from 1 to 20 GHz and second is set at 5 GHz. A data signal of 10 Gbps is transmitted over long haul single mode fiber by single tone system. A very good bit error rate (BER) 10^?40 performances for 100 km and 25 km fiber link is achieved for both single tone and two tones respectively in proposed microwave over fiber communication system.     

Design of a super wide-band EM wave absorber for a general purpose anechoic chamber

In order to construct an anechoic chamber satisfying international standards for EMI testing, it has been recognized that the absorption characteristics of the EM wave absorber must be higher than 20 dB over the frequency band from 30 MHz to 18 GHz. In this paper, an EM wave absorber with super wide-band frequency characteristics is proposed and designed in order to satisfy the above requirements by using the EMCM and FDTD. As a result, the proposed absorber has absorption characteristics higher than 20 dB over the frequency band from 30 MHz to more than 20 GHz.     

Realization of compatible stealth material for infrared,laser and radar based on one-dimensional doping-structure photonic crystals

To inhibit the radiant infrared energy between 8 and 14 μm, which is the infrared atmospheric window, and decrease the echo power of detecting laser and radar, to achieve compatible stealth, a doping structural one-dimensional photonic crystal (1-D PC) with Ge, ZnSe and Si was fabricated; and then combine it with radar absorbing material (RAM) to make a compound. After that, the reflection spectra of this compound was tested, and the result shows a high average reflectance (89.5%) in 8–14 μm waveband, and a reflective valley (39.8%) in the wavelength of 10.6 μm, which is the wavelength of CO₂ laser; and the reflectance in radar band shows that at high frequency, especially between 7.8 and 18 GHz, the radar power is strongly absorbed by this material and the reflected energy attenuate over 10 dB within the range from 11.1 GHz to 18.3 GHz, even 24.5 dB to the most in the frequency of 14.6 GHz.     

High LO-to-RF isolation 94 GHz coplanar monolithic down-converter for FMCW radar sensor applications

This paper presents a 94 GHz monolithic down-converter with low conversion loss and high local oscillator (LO)-to-RF isolation using the 0.1 μm T-gate metamorphic high electron-mobility transistor (MHEMT) technology. The down-converter consists of a one-stage amplifier and a single-balanced mixer based on the high-directivity tandem coupler structure using the air-bridge crossovers, thereby amplifying the RF signals and maximizing the LO-to-RF isolation by using an inherent S₁₂ isolation characteristic of the amplifier and good phase balance of the tandem coupler. The fabricated one-stage amplifier using a 30 μm × 2 MHEMT shows a small signal gain of 7 dB at 94 GHz. The single-balanced mixer comprising two 20 μm × 2 MHEMT Schottky diodes and the tandem coupler with an additional λ/4-length line exhibits the conversion loss less than 7.8 dB and the LO-to-RF isolation higher than 30 dB in a RF frequency range of 91–96 GHz. Two circuits designed both for a 50 Ω impedance system are integrated into the down-converter of a 2.6 × 2.5 mm² chip size, and it shows a low conversion loss of ∼1 dB at 94 GHz and excellent LO-to-RF isolation above 40 dB in a frequency range of 90–100 GHz. This is the best isolation among the W-band monolithic down-converters reported to date.     

Study of all-fiber asymmetric interleaver based on two-stage cascaded Mach–Zehnder Interferometer

In order to improve the transmission efficiency of optical-fiber communication system with 10 Gb/s + 40 Gb/s, an all-fiber interleaver with unequal passband is proposed and discussed, which is based on a two-stage cascaded Mach-Zehnder interferometer (MZI). The optimum value of structural parameters, such as splitting ratios of the couplers and the physical length differences of the interferometer arms, were chosen. One set of optimized data is validated in the experimental result. The experimental results and the theoretic analysis indicate that an all-fiber optical interleaver with 3 dB passband width in odd channels and even channels could be obtained, which having more than 60 GHz passband and 30 GHz passband, for transmission speed of 40 Gb/s and 10 Gb/s, respectively. By assigning different portions of spectrum to the 10 Gb/s and the 40 Gb/s channels, the bandwidth efficiency requirement of the 40 Gb/s channel is relieved, and therefore longer transmission distance can be achieved.     

RF behavior of triple-frequency high power fusion gyrotron

The RF behavior of high power, triple frequency (170-, 127.5-, and 85 GHz) gyrotron for fusion application is presented in this paper. The operating mode selection is discussed in detail for each corresponding frequencies and TE_34,10, TE_25,8 and TE_17,5 modes are selected as the operating mode for 170 GHz, 127.5 GHz and 85 GHz operation of the device, respectively. The interaction cavity geometry and beam parameters are finalized by the cold cavity analysis and beam-wave interaction simulations. Considering the beam parameters and the beam launching positions in cavity (beam radius), the design of Magnetically Tunable MIG (MT-MIG) is also presented. Results of MT-MIG confirm the beam launching with desired beam parameters at the beam radius corresponding to the selected operating modes for all three frequencies. The CVD diamond window is also designed for RF power transmission. The beam-wave interaction simulations confirm more than 1 MW power at all three frequencies (170-, 127.5-, and 85 GHz).     

Electromagnetic wave absorption properties of ε-Fe3N/Y2O3 nanocomposites derived from Y2Fe17 intermetallic compound

The electromagnetic wave absorption properties of ε-Fe₃N/Y₂O₃ nanocomposites were characterized in a frequency range of 0.05–20.05 GHz. The imaginary part of relative permeability μ_r″ exhibited “twin peak” dispersion and μ_r″ value retained high over a 0.5–10 GHz range. The real part (ε_r′) and imaginary part (ε_r″) of relative permittivity almost kept a low constant in a region of 0.5–10 GHz, respectively. As a result, the resin composites with 51 vol% ε-Fe₃N/Y₂O₃ powders exhibited excellent electromagnetic wave absorption properties (RL<−20 dB) in a frequency range of 0.6–4.4 GHz, with a thickness of 3.3–19.3 mm. A minimum reflection loss of −55 dB was observed at 1.8 GHz with an absorber thickness of 7.05 mm.     

An external cavity diode laser using a volume holographic grating

This study presents an external cavity diode laser (ECDL) system, utilizing a volume holographic grating (VHG) and a microfabricated silicon flexure as the VHG holder. The laser design is aimed for easy assembly, controllability, and better stability of the laser cavity. The laser frequency was stabilized to a D₂ transition of rubidium at 780.247 nm, with a mode-hop-free tuning range of 16 GHz and 9.6 GHz with and without feed-forward on the diode injection current. The measured linewidth was 850 kHz in 500 s, qualified for laser cooling experiments.     

Optimization of Super Dense WDM systems for capacity enhancement

We investigate the performance of the Super Dense Wavelength Division Multiplexed (SDWDM) systems with high spectral efficiency and narrow spacing of the channels and optimization in terms of bit rate up to 15 Gbps, channel spacing as low as 12.5 GHz, number of channels up to 64 and repeater less transmission distance up to 100 km and report high capacity SDWDM systems. We demonstrate the minimal allowed channel spacing and provide recommendations for future SDWDM solutions. The simulation results have shown that the minimum channel spacing for 15 Gbps, 32 channel system need to be not less than 0.35 nm and that for a 10 Gbps system it should be not less than 0.25 nm. The 5 Gbps system gives acceptable results at spacing of 0.1 nm for maximum up to single span of 80 km.     

Wide-band fanned-out supercontinuum source covering O-, E-, S-, C-, L- and U-bands

A wide-band supercontinuum source generated by mode-locked pulses injected into a Highly Non-Linear Fiber (HNLF) is proposed and demonstrated. A 49 cm long Bismuth–Erbium Doped Fiber (Bi–EDF) pumped by two 1480 nm laser diodes acts as the active gain medium for a ring fiber laser, from which mode-locked pulses are obtained using the Non-Polarization Rotation (NPR) technique. The mode-locked pulses are then injected into a 100 m long HLNF with a dispersion of 0.15 ps/nm km at 1550 nm to generate a supercontinuum spectrum spanning from 1340 nm to more than 1680 nm with a pulse width of 0.08 ps and an average power of ?17 dBm. The supercontinuum spectrum is sliced using a 24 channel Arrayed Waveguide Grating (AWG) with a channel spacing of 100 GHz to obtain a fanned-out laser output covering the O-, E-, S-, C-, L- and U-bands. The lasing wavelengths obtained have an average pulse width of 9 ps with only minor fluctuations and a mode-locked repetition rate of 40 MHz, and is sufficiently stable to be used in a variety of sensing and communication applications, most notably as cost-effective sources for Fiber-to-the-Home (FTTH) networks.