High-power dual-rod Yb:YAG laser

We describe a diode-pumped Yb:YAG laser that produces 1080 W of power cw with 27.5% optical optical efficiency and 532 W Q-switched with M(2)=2.2 and 17% optical-optical efficiency. The laser uses two composite Yb:YAG rods separated by a 90 degrees quartz rotator for bifocusing compensation. A microlensed diode array end pumps each rod, using a hollow lens duct for pump delivery. By changing resonator parameters we can adjust the fundamental mode size and the output beam quality. Using a flattened Gaussian intensity profile to calculate the mode-fill efficiency and clipping losses, we compare experimental data with modeled output power versus beam quality.     

A keyhole volumetric model for weld pool analysis in Nd:YAG pulsed laser welding

This study presents a new model for analyzing the temperature distribution and weld pool shape in Nd:YAG pulsed laser welding. In the proposed approach, a surface flux heat transfer model is applied in the low laser energy intensity region of the weld, while a keyhole heat transfer model based on a volumetric heat source is applied in the high laser energy intensity region of the weld. The correlation between the intensity of the laser input energy and the geometric parameters of the volumetric heat source is derived experimentally. A series of MARC finite element simulations based on the proposed single pulse model are performed to investigate the shape and size of the weld pool given different laser energy intensities. A good agreement is observed between the simulation results and the experimental results obtained under equivalent single pulse welding conditions. Thus, the basic validity of the proposed model is confirmed.     

Gas protection optimization during Nd:YAG laser welding

Many laser processes, such as welding or surface treatments are associated with an undesired phenomenon, which is oxidation. The solution commonly employed to solve this problem approaches the shielding gas and/or the shielding gas device. What we propose in this paper is a methodology with the goal to optimize the protection gas device design as well as the gas flow in the case of laser welding and surface treatments. The pressure created by the gas flow on the sample surface is recorded and analysed together with the operating parameters influence in order to reach the objectives. The nozzle system designed and presented below assures the protection against material oxidation using minimal gas flow rates and increases the welding penetration in the case of high-power Nd:YAG laser welding.     

Characterisation of cw Nd : YAG laser keyhole dynamics

The paper concerns laser–matter interaction characterisation. In this work, we use a rapid CCD camera located coaxially to the laser beam and we compare recorded images with those obtained by numerical modelling. Because images are difficult to understand, we compute thermal radiation emitted by a keyhole of fixed geometry and we adjust it trying to approach the camera record. The modelling treats radiative heat transfer within the keyhole and determines the sensor illumination map. By adjusting the geometrical characteristics of the hole, we seek to obtain the image that corresponds as well as possible to the realised experiment. Results are compared with other experimental methods simultaneously performed plume characterisation with an electric probe and spectrometric analysis. They show the existence of two distinct behaviours of the keyhole: a pseudo-steady state associated with regular and pseudo-constant keyhole shapes, low frequencies of electric current in the plume, and generally good welding results, and a highly dynamic mode associated with irregular and rapidly varying keyhole shapes, high frequencies in the plume current and generally poor welding results.     

Highly efficient cryogenically-cooled Yb:YAG laser

A MOPA laser system for high pulse energy and high average power has been developed by using a cryogenic Yb:YAG. In the regenerative amplifier with our original TRAM architecture, the high pulse energies of 6.5 and 1.5 mJ were obtained at the repetition rate of 200 Hz and 1 kHz, respectively. An optical efficiency was as high as η_o-o = 9.3% with an excellent beam quality of M ² < 1.1, which ensured that a cryogenic Yb:YAG TRAM had a high thermal strength. The following four pass power amplifier with a cryogenic Yb:YAG rod showed 140 mJ at 100 Hz. Both a high optical efficiency of η_o-o = 30% and a high slope efficiency of η_s = 44% showed that an efficient laser operation could be realized for a power amplification with both a high pulse energy and a high average power by using a cryogenic Yb:YAG.     

Efficient tunable Yb:YAG ceramic laser

A high-power efficient ceramic Yb:YAG laser was demonstrated at a room temperature of 20 °C with an Yb concentration of 9.8 at.%, a gain medium of 1 mm, a pumping power of 13.8 W, an output coupler of T = 10%, and a cavity length of 20 mm. A 6.8 W cw output power was obtained with a slope efficiency of 72%. The ceramic Yb:YAG laser exhibited a continuous tunability in the spectral range of 63.5 nm from 1020.1 to 1083.6 nm for T = 1% at a maximum output power of 1.6 W. To the best of our knowledge, this is the first study of the tunability of ceramic Yb:YAG lasers, except crystal Yb:YAG studies.     

梯度掺杂Yb ∶YAG重频激光器热管理研究

为了改善重频激光器的热性能,本文采用了键合Yb ∶YAG晶体薄片作为激光增益介质,介质中掺杂粒子浓度呈梯度分布.文章计算了不同参数条件下介质抽运过程,得到介质内部的储能,温度和应力分布,并从中选出较为优化的介质参数.计算表明,采用梯度掺杂的方法,介质温度降低,形变和热应力减小,波前畸变改善.理论上证明了采用梯度掺杂的方法改善热管理的可行性. 关键词： 梯度掺杂 键合 Yb ∶YAG 热管理     

梯度掺杂Yb:YAG重频激光器热管理研究

为了改善重频激光器的热性能,本文采用了键合Yb:YAG晶体薄片作为激光增益介质,介质中掺杂粒子浓度呈梯度分布.文章计算了不同参数条件下介质抽运过程,得到介质内部的储能,温度和应力分布,并从中选出较为优化的介质参数.计算表明,采用梯度掺杂的方法,介质温度降低,形变和热应力减小,波前畸变改善.理论上证明了采用梯度掺杂的方法改善热管理的可行性.     

Diffraction losses of Nd:YAG and Yb:YAG laser crystals

Based on space-dependent rate equations, the lowest threshold input power for a diode end-pumped solid-state laser is obtained for the pump spot size w_p→0. However, as the pump beam waist is decreased, the thermally induced effects in the laser rod would be very high. Diffraction losses caused by radial and tangential variations of refractive index have been analyzed and compared for the Nd : YAG and the Yb : YAG at room temperature (300 K) and liquid-nitrogen temperature (77 K).     

200-W corner-pumped Yb:YAG slab laser

A novel concept of corner pumping has been developed. The corner-pumped slab design allows long absorption length and symmetric conduction cooling, making it particularly suitable for high-power quasi-three-level lasers. A corner-pumped Yb:YAG slab laser has been demonstrated for the first time. A preliminary experimental result shows that the laser produces 202 W of cw output power with 1400 W of incident pump power. PACS 42.55.Xi; 42.60.Da; 42.60.Pk     

双重复频率锁模Yb:YAG陶瓷激光器

近年来,双重复频率锁模激光器在诸如双光梳光谱和异步光学采样等应用领域吸引了广泛关注.基于单一激光腔的双梳系统能大大降低成本,简化系统结构,且性能优异.双重复频率锁模激光器为发展紧凑型和实用型双梳装置开辟了道路.本文报道了一种可用作双光梳光谱系统光源的双重复频率锁模Yb:YAG陶瓷激光器.该激光器基于半导体可饱和吸收镜锁模技术,采用双通道抽运结构,利用新型非水基流延成型制备的Yb:YAG透明陶瓷,在单一的五镜腔中,当吸收抽运光功率为5.6 W时,实现了自启动、稳定运转的双重复频率锁模脉冲Pulse1和Pulse2,其重复频率分别为448.918和448.923 MHz,重复频率差为5 kHz.在吸收抽运功率为7 W时,得到最大的总平均输出功率170 mW,其中Pulse1和Pulse2的功率分别为89和81 mW,相应的光谱宽度分别为1和1.16 nm.性能相似的双重复频率脉冲彼此间保持了良好的相干性,实验结果证明了双通道抽运在双重复频率锁模激光器应用中的可行性,此种新型双重复频率激光器在双光梳光谱和测距等领域具有较好的应用潜力.     

165-W cryogenically cooled Yb:YAG laser

Thermo-optic distortions often limit the beam quality and power scaling of high-average-power lasers. Cryogenically cooled Yb:YAG is used to efficiently generate 165 W of near-diffraction-limited beam from a power oscillator with negligible thermo-optic effects. End pumped with 215 W of incident pump power from two diode modules, the laser has an optical-optical efficiency of 76%, a slope efficiency of 85%, and an M2 value of 1.02.     

High-power diode-pumped mode-locked Yb:YAG ceramic laser

A high-power diode-pumped passively mode-locked Yb:YAG ceramic laser was demonstrated. An average output power of 3.80W with a pulse duration of 433 fs at a repetition rate of 90.9MHz was obtained at a wavelength of 1050 nm using a 2% output coupler. A peak power of 96.5kW was also obtained. To the best of our knowledge, these are the highest reported average power and peak power for a diode-pumped mode-locked Yb:YAG ceramic laser.     

250 W single-crystal fiber Yb:YAG laser

We demonstrate an Yb:YAG single-crystal fiber laser with 251 W output power in continuous-wave and an optical efficiency of 44%. This performance can be explained by the high overlap between pump and signal beams brought by the pump guiding and by the good thermal management provided by the single-crystal fiber geometry. The oscillator performance with a reflectivity of the output coupler as low as 20% also shows high potential for power amplification.     

A passively Q-switched Yb:YAG microchip laser

We present a diode-pumped passively Q-switched Yb:YAG microchip laser, using a semiconductor saturable absorber mirror. We obtained pulses with 1.1-μJ energy, 530-ps duration, 1.9-kW peak power, and a repetition rate of 12 kHz. The laser is oscillating in a single longitudinal mode. Received: 23 October 2000 / Published online: 7 February 2001     

万瓦级光纤激光焊接过程中小孔内外等离子体研究

为了进一步深入了解超高功率光纤激光深熔焊接过程中等离子体特征,试验拍摄了深熔小孔内外等离子体形态,并采用光谱仪检测分析了光纤激光致等离子体光谱信号.利用检测得到的等离子体光谱信号,计算研究了等离子体的电子温度、电子密度、电离度以及等离子体压力特征,并分析了在小孔内不同深度处及孔外等离子体的变化规律.结果表明,孔内等离子体呈现不均匀分布特征,孔外金属蒸气远多于等离子体.等离子体光谱分析显示,光纤激光致等离子体辐射出的谱线较少,即电离程度较低.进一步的计算结果同样证实了光纤激光致等离子体处于弱电离状态,但等离子体电子密度仍然处于较高水平,且等离子体瞬态压力可达到数百个大气压.     

LD side-pumped passively Q-switched Yb:YAG slab laser

A quasi-continuous wave laser diode side-pumped passively Q-switched Yb:YAG slab laser with Cr⁴⁺:YAG saturable absorber has been demonstrated in order to understand the pulse properties of Yb:YAG crystal. To our knowledge the maximum 69% extraction efficiency is achieved by the system. 44 μJ pulse energy and 1.64 KW peak power with near diffraction-limited beam quality are presented at 25 Hz repetition rate. The build-up time of the Q-giant in the passively Q-switched laser is shown.     

一种用于Yb:YAG激光器的波长分离膜的研制

以1 030 nm高反,940,980 nm高透的波长分离膜作为实例,为提高该薄膜元件的波长分离效果,从膜系的优化方面做了一系列的研究,诸如采用带通滤光片的设计思想,在膜堆两侧加入了匹配层,调整膜堆的周期厚度,并用膜系设计软件对通带作进一步的优化.通过这一系列的优化设计后,利用RF双离子束溅射工艺在BK7玻璃基底上沉积样品薄膜,并在基底背面加镀通带增透膜.结果显示,透射带在940和980 nm处的透过率分别为97.73%和93.63%,反射带在1 030 nm的反射率为99.99%.对所制备的样品薄膜进行了激光损伤阈值测量,得到了35 J/cm2(1 064 nm,12 ns)的结果.     

LD end-pumped intracavity frequency doubled Yb:YAG laser

A laser diode end-pumped 10 at.% doped Yb:YAG microchip crystal intracavity frequency doubled all solid-stated green laser is reported in this paper. Using one plano-concave resonator, with the pump power of 1.2 W, 44.2 mW TEM₀₀ continuous wave (CW) laser at 525 nm was obtained, the optical conversion efficiency was about 3.7%. When a Cr:YAG crystal with initial transmission of 95.5% inserted in the resonator, the maximum output power of 6.4 mW, pulse duration width of 49.1 ns, pulse repetition rate of 2.45 kHz, and peak power of 53.1 W at 515 nm were achieved when the pump power was 1.2 W. The wavelength changed from 525 nm to 515 nm and the threshold was only 725 mW.     

Diode-pumped Kerr-lens mode-locked femtosecond Yb:YAG ceramic laser

We experimentally demonstrated a diode-pumped Kerr-lens mode-locked femtosecond laser based on an Yb:YAG ceramic. Stable laser pulses with 97-fs duration, 2.8-nJ pulse energy, and 320-mW average power were obtained. The femtosecond oscillator operated at a central wavelength of 1049 nm and a repetition rate of 115 MHz. To the best of our knowledge, this is the first demonstration of a Kerr-lens mode-locked operation in a diode-pumped Yb:YAG ceramic laser with sub-100 fs pulse duration.