Design of hybrid photonic crystal fiber: Polarization and dispersion properties

A highly birefringent dispersion compensating hybrid photonic crystal fiber is presented. This fiber successfully compensates the chromatic dispersion of standard single mode fiber over E- to L-communication bands. Simulation results reveal that it is possible to obtain a large negative dispersion coefficient of about −1054.4 ps/(nm km) and a relative dispersion slope of 0.0036 nm⁻¹ at the 1550 nm wavelength. The proposed fiber simultaneously provides a high birefringence of order 3.45 × 10⁻² at the 1550 nm. Moreover, it is confirmed that the designed fiber successfully operates as a single mode in the entire band of interest. For practical conditions, the sensitivity of the fibers dispersion properties to a ±2% variation around the optimum values is carefully studied and the nonlinearity of the proposed fiber is also reported and discussed. Such fibers are essential for high speed transmission system as a dispersion compensator, sensing applications, fiber loop mirrors as well as maintaining single polarization, and many nonlinear applications such as four-wave mixing, etc.     

Design of a highly nonlinear twin bow-tie polymer photonic quasi-crystal fiber with high birefringence

A twin bow-tie polymer-based photonic quasi-crystal fiber with high birefringence, high nonlinearity and low dispersion as well as maintaining single mode operation is presented in the wavelength range 1.8–2.2 μm. Through optimizing fiber structure parameter using a full-vector finite-element method combined with perfectly matched layers boundary condition, the birefringence is as high as 2.43 × 10⁻³, the nonlinearity is as high as 118 W⁻¹ km⁻¹, and the dispersion is only 25 ps/nm/km at 2 μm with the holes pitch of 3.3 μm. From the point of fabrication, the influences of deviation of each air hole diameter are discussed to verify the robustness of the photonic quasi-crystal fiber designed.     

Compact and efficient coupler to interface hybrid dielectric-loaded plasmonic waveguide with silicon photonic slab waveguide

A coupler is proposed to interface a hybrid dielectric-loaded plasmonic waveguide (HDLPW) with a silicon photonic slab waveguide. The HDLPW is firstly designed and optimized to attain the best tradeoff between the mode confinement and the propagation distance. The designed coupler is inspired from the taper configuration and numerically modeled through finite-difference time-domain (FDTD) simulation. The results demonstrate that a high confinement and low loss of the energy is achieved from a silicon photonic slab waveguide into the dielectric slot of area 50×200 nm² in the HDLPW. The transmission attained through the coupler with a compact size of 400 nm is found to be as high as 80% (1 dB). Further, the planar nature of taper configuration makes the coupler easy to fabricate using the state-of-the-art CMOS facilities. The proposed coupler is useful in enabling the integration between photonic and hybrid plasmonic waveguides and thus realizing on-chip hybrid integrated circuits.     

Polarization insensitive hollow optical waveguide

A polarization insensitive hollow optical waveguide is proposed. The propagation characteristics of orthogonal polarizations in the hollow waveguide are effectively controlled in simulation to provide polarization insensitivity by tailoring the parameters associated with the two mirrors—a high-index contrast grating (HCG) mirror and a distributed Bragg reflecting (DBR) mirror, on either side of an air-core. The polarization insensitivity is evidenced by a low polarization dependence loss of 1.36 dB/cm and a low modal birefringence of 1.01 × 10^? 4.     

Dispersion and Confinement Loss Control in Modified Hexagonal Photonic Crystal Fibers

This paper presents a novel technique for the control of chromatic dispersion and confinement loss in hexagonal photonic crystal fibers (H-PCFs). It is demonstrated that it is possible to obtain very low chromatic dispersion of 0 ± 0:38 ps/(nm·km) in the wavelength range of 1.41 to 1.66 μm and confinement loss of less than 0.0001 dB/km from a six ring modified H-PCF (MH-PCF). The higher order dispersion at 1.55 μm is about −0.001 ps/(nm²-km).     

Soliton propagation optimization and dynamic modulation in photonic crystal waveguide with polystyrene background

Bright optical soliton propagation properties near the left band edge of photonic crystal waveguide (PCW) are numerically investigated. Compared with the normal PCW with air background, by employing polystyrene as PCW background and adjusting the structure parameters simultaneously, the required soliton peak power sharply decreases from 8.63 × 10⁶ W/m to 9.98 × 10² W/m. The influence of optical loss on soliton propagation is numerically investigated. The dynamic modulation of the soliton propagation in PCW is realized, and a modulation range of 459 nm wavelength for the soliton transmission has been achieved. Simulation results show that the transmission wavelength, required soliton peak power and delay time decrease almost linearly as the external modulated voltage increases; the modulation sensitivities are 8.316 nm/V, 3.416 W/m/V and 16.6 ps/V, respectively.     

Simulation of 16 × 10 Gb/s WDM system based on optical amplifiers at different transmission distance and dispersion

In this paper, the 16 channel WDM systems at 10 Gb/s have been investigated for the various optical amplifiers and hybrid optical amplifiers and the performance has been compared on the basis of transmission distance and dispersion. The amplifiers EDFA and SOA have been investigated independently and further compared with hybrid optical amplifiers like RAMAN-EDFA and RAMAN-SOA. It is observed that hybrid optical amplifier RAMAN-EDFA provides the highest output power (12.017 and 12.088 dBm) and least bit error rate (10^?40 and 9.08 × 10^?18) at 100 km for dispersion 2 ps/nm/km and 4 ps/nm/km respectively.     

Highly nonlinear dispersion-flattened square photonic crystal fibers with low confinement losses

A new simple structure of an index-guiding highly nonlinear dispersion-flattened square photonic crystal fiber (HNDFSPCF) with low confinement losses is proposed. The results reveal that it is possible to design five-rings HNDF-SPCFs with a flattened dispersion of 0.43 ps/(nm·km), low dispersion slope of -0:02 ps/(nm²·km), low confinement loss of approximately 10³ dB/m, and a large nonlinear coefficient of approximately 35W^-1 km^-1 at 1.55 μm. It is also observed that the confinement loss is less than 10^-1 dB/m in the wavelength range of 1.2 –1.7 μm.     

Highly birefringent ZBLAN photonic quasi-crystal fiber with four circular air holes in the core

A highly birefringent ZBLAN photonic quasi-crystal fiber with a rectangular array of four relatively small circular air holes in the core region is proposed. Through optimizing fiber structure parameters using a full-vector finite-element method combined with perfectly matched layers boundary condition, its birefringence is up to 2.88 × 10⁻² and the confinement losses of both polarized modes are less than 4.95 × 10⁻⁴ dB/m at 2 μm. To our knowledge, this is the first simulation study showing that a birefringence can be achieved with the order of 10⁻² by all-circular-hole PQFs around 2 μm.     

Novel slow-light waveguide with large bandwidth and ultra low dispersion

To tailor the bandwidth and the group-velocity dispersion, we demonstrate a novel waveguide based on a photonic crystal within a triangular array with crescent-like-shaped air holes. By changing the angle between the waveguide axis and symmetric axis of the air hole from 0 to π/2, we find that the available bandwidth with a nearly constant group index in excess of 22 increases from 7 nm to 13 nm, that the corresponding normalized delay-bandwidth product increases from 0.202 to 0.245, and that the absolute value of the group-velocity dispersion decreases from 13.500 ps²/km to 10 ps²/km. The origin of all the findings is related to the widening of the slow-light region with the increasing of the angle.     

Performance evaluation of 64 × 10 Gbps and 96 × 10 Gbps DWDM system with hybrid optical amplifier for different modulation formats

In this paper, we investigated the performance of multi terabits DWDM system consisting of hybrid optical amplifier RAMAN-EDFA for different data format such as non-return to zero (NRZ), return to zero (RZ) and differential phase shift keying (DPSK). We find that in 64 × 10 and 96 × 10 Gbps, RZ is more adversely affected by nonlinearities, where as NRZ and DPSK is more affected by dispersion. We further show that RZ provide good quality factor (13.88 dB and 15.93 dB for 64 and 96 channels), less eye closure (2.609 dB and 3.191 dB for 64 and 96 channels) and acceptable bit error rate (3.89 × 10⁸ and 1.24 × 10⁹ for 64 and 96 channels) at the respective distance as compare to other existing modulation format. We further investigated the maximum single span distance covered by using existing data formats.     

Characterization of the channel walls roughness in photonic crystal fibers

We present electron microscope (FEI NanoSEM) and atomic force microscopy measurements of surface roughness in nanochannels in photonic crystal fibers (PCF). A method was invented to cleave the PCF along the axis without damaging the surface structure in the nanochannels allowing us to characterize the morphology of the nanochannels in the PCF. A multi-wall carbon nanotube mounted onto commercial AFM probes and super sharp silicon non-contact mode AFM probes were used to characterize the wall roughness in the nanochannels. The roughness is shown to have a Gaussian distribution, and has an amplitude smaller than 0.5 nm. The height–height correlation function is an exponential correlation function with an autocorrelation length of 13 nm, and 27 nm corresponding with scan sizes of 200×100 nm², and 1600×200 nm², respectively.     

Two photon absorption characteristics of bulk GaTe crystal

We have investigated the structural and optical properties of bulk GaTe crystal grown by vertical Bridgman method. Two photon absorption (TPA) properties of GaTe crystal have been investigated by the open aperture Z-scan technique under 1064 nm wavelength with 4 ns or 65 ps pulse durations. The TPA coefficients are greater in ns regime than that of ps regime. Upon increasing intensity of incident light from 5.02×10⁷ W/cm² to 1.07×10⁸ W/cm², the TPA coefficients increased from 3.47×10^?6 cm/W to 8.53×10^?6 cm/W for nanosecond excitation. Similarly, when intensity of incident light was increased from 6.81×10⁸ W/cm² to 9.94×10⁸ W/cm² the TPA coefficients increased from 3.53×10^?7 cm/W to 6.83×10^?7 cm/W for picosecond excitation. Measured TPA coefficient of GaTe crystal is larger than that of GaSe and GaS layered crystals.     

High index contrast Er:Ta2O5 waveguide amplifier on oxidised silicon

We report a high index contrast erbium doped tantalum pentoxide waveguide amplifier. 2.3 cm long waveguides with erbium concentration of 2.7 × 10²⁰ cm^? 3 were fabricated by magnetron sputtering of Er-doped tantalum pentoxide on oxidised silicon substrates and Ar-ion milling with photolithographically defined mask. A net on-chip optical gain of ~ 2.25 dB/cm at 1531.5 nm was achieved with 20 mW of pump power at 977 nm launched into the waveguide. The pump threshold for transparency was 4.5 mW.     

CMOS—compatible reconfigurable microring demultiplexer with doped silicon slab heater

We present a 1×4 reconfigurable demultiplexer based on cascaded silicon microring resonators. The device is fabricated on a 0.18 μm complementary metal oxide semiconductor (CMOS) process. A homogeneous doped silicon slab heater is proposed and fabricated directly on the slab region of the microring resonator for thermal tuning. The flows of the heating currents in the heaters are parallel to the ring waveguide through the heavily doped slab regions located on both sides of the ring waveguide without through the waveguide core regions. The proposed doped heaters are experimentally verified with low-voltage operation and tuning efficiency of ～77 pm/mW. Without any tuning or trimming, predicted average channel spacing distribution in the whole free spectral range (FSR) is demonstrated. Full reconfigurability is also demonstrated in the demultiplexer with channel spacing of 2 nm (250 GHz) and 1 nm (125 GHz), corresponding to channel isolation of less than ?21 dB and ?16 dB, respectively. Such a low-voltage operation and reconfigurable demultiplexer is suitable for on-chip optical interconnect.     

A high-Q biochemical sensor using a total internal reflection mirror-based triangular resonator with an asymmetric Mach–Zehnder interferometer

We propose and analyze a high effective Q-factor triangular ring resonator (TRR) coupled with an asymmetric Mach–Zehnder interferometer (AMZI), in which the long evanescent fields on a total internal reflection (TIR) mirror in the TRR and the field cancelation by the phase difference of each path in the AMZI are utilized. The TRR is employed in order to more effectively measure the quantities that occur during biological events because the evanescent field of the TIR mirror with its sharp incident angle is influenced by the Goos–Hänchen shift. In this paper, we report upon the AMZI-coupled TRR sensor structure with the high effective Q-factor of about 10⁵ obtained through the optimization of the AMZI path-length. The sensitivity of the resonance shift when changing the refractive index of 1 × 10^? 4 at the incidence angle of 22.92° has been identified to be as high as 0.48 × 10⁴ nm/RIU. In addition, the power sensitivity of the AMZI-coupled TRR with a 17 dB attenuation is 5.7 × 10⁵ dB/RIU.     

Wide-band fanned-out supercontinuum source covering O-, E-, S-, C-, L- and U-bands

A wide-band supercontinuum source generated by mode-locked pulses injected into a Highly Non-Linear Fiber (HNLF) is proposed and demonstrated. A 49 cm long Bismuth–Erbium Doped Fiber (Bi–EDF) pumped by two 1480 nm laser diodes acts as the active gain medium for a ring fiber laser, from which mode-locked pulses are obtained using the Non-Polarization Rotation (NPR) technique. The mode-locked pulses are then injected into a 100 m long HLNF with a dispersion of 0.15 ps/nm km at 1550 nm to generate a supercontinuum spectrum spanning from 1340 nm to more than 1680 nm with a pulse width of 0.08 ps and an average power of ?17 dBm. The supercontinuum spectrum is sliced using a 24 channel Arrayed Waveguide Grating (AWG) with a channel spacing of 100 GHz to obtain a fanned-out laser output covering the O-, E-, S-, C-, L- and U-bands. The lasing wavelengths obtained have an average pulse width of 9 ps with only minor fluctuations and a mode-locked repetition rate of 40 MHz, and is sufficiently stable to be used in a variety of sensing and communication applications, most notably as cost-effective sources for Fiber-to-the-Home (FTTH) networks.     

Raman gain in modified tellurite glasses and thin films

We report the tailoring of Raman spectra of the tellurite glass by varying molar concentrations of phosphates, fluorides in phosphate modified tellurite glasses to analyze the Raman gain. From the measured Raman spectrum, the Raman gain and gain bandwidth in these glasses were calculated and compared. The structural features that give rise to the observed spectra and its dependence on glass composition are identified and reported. Raman gain as high as 170 × 10^? 13 m/W is obtained for glass modified by zinc oxide. Glass thin films prepared by pulsed laser deposition show a Raman gain of 5.0 × 10^? 13 m/W suggesting their importance in short waveguide Raman amplifier fabrication.     

Application of self-collimated beams to realization of all optical photonic crystal encoder

In this paper a 4×2 optical encoder is proposed by employing the self-collimation effect in 2D photonic crystals. The total structure of the proposed device is a combination of so called “beam splitters” and “mirrors”. The simulation result indicates that, this design can operate as 4×2 optical encoder, the footprint of structure is about 69 µm×55 µm and response time is about 1.4 ps.     

2D FDTD simulation of low loss small angle bend and Y branch configurations in a photonic crystal waveguide layout with a Mach–Zehnder device design configuration

A technique to produce low loss small angle bends in photonic crystal waveguides is presented. The technique consists of bridging parallel input and output waveguide segments with an inclined waveguide region of the same basic design that has a lateral dielectric shift. Results are presented for waveguides produced by enlarging the silicon gap along the central line, separating air holes in a square array photonic crystal for the TE polarization and an operating wavelength of λ_o = 1.55 μm. This low loss waveguide bending technique is applied to the design of Y branch and Mach–Zehnder photonic crystal structures. Simulation of the performance of the dielectric structures is achieved using 2-D FDTD, similar results are anticipated when applied to 3-D waveguide configurations and for other photonic crystal layouts.