酸蚀深度对熔石英三倍频激光损伤阈值的影响

 采用干涉仪和台阶仪测试蚀刻深度随时间的变化,结合材料去除速率测量,研究了HF酸蚀液对熔石英表面蚀刻的影响。测试了蚀刻后损伤阈值和表面粗糙度的变化。研究表明,熔石英表面重沉积层厚度约16 nm,亚表面缺陷层大于106 nm;重沉积层去除后损伤阈值增大,随亚表面缺陷层暴露其阈值先降低后又增加,最后趋于稳定;然而,随蚀刻时间的增加,其表面粗糙度增大。分析表明,蚀刻到200 nm能有效地提高熔石英的低损伤阈值,有利于降低初始损伤点数量和提高熔石英表面的机械强度。     

熔石英元件HF刻蚀的实验研究

为深入了解熔石英元件化学刻蚀过程,研究了HF刻蚀反应机理、HF刻蚀工艺参数以及刻蚀对表面质量的影响规律。通过控制变量法,获得刻蚀速率随HF浓度、刻蚀温度以及NH4F浓度的变化规律。对刻蚀不同深度后的元件表面粗糙度、形貌、杂质含量以及激光损伤阈值进行了检测,实验结果表明:刻蚀速率受多种因素共同影响,其中HF浓度的促进作用最为显著;刻蚀后的熔石英表面形貌复杂,有横向、纵向、拖尾等形式的划痕,以及坑点、杂质等缺陷,其中横向划痕和纵向划痕占据了缺陷部分的主体,主要杂质铈元素随刻蚀时间的增长不断减少;激光损伤阈值测量实验表明,通过HF刻蚀将元件损伤阈值提高了59.6%。     

酸蚀与紫外激光预处理结合提高熔石英损伤阈值

采用HF酸刻蚀和紫外激光预处理相结合的方式提升熔石英元件的负载能力,用质量分数为1%的HF缓冲溶液对熔石英刻蚀1~100 min,综合透过率、粗糙度和损伤阈值测试结果,发现刻蚀时间为10min的熔石英抗损伤能力最佳。采用355 nm紫外激光对HF酸刻蚀10 min的熔石英进行预处理,结果表明:紫外预处理能量密度在熔石英零损伤阈值的60%以下时,激光损伤阈值单调递增;能量到达80%时,阈值反而低于原始样片的损伤阈值。适当地控制酸蚀时间和紫外激光预处理参数能有效提高熔石英的抗损伤能力。     

静/动态刻蚀对熔石英表面质量和激光损伤的影响

为了研究静/动态刻蚀过程中熔石英表面质量和抗激光损伤性能的演变规律,优化化学刻蚀工艺,使用HF酸缓冲液对熔石英分别进行了不同时间的静/动态刻蚀处理。实验表明,由于兆声场辅助搅拌作用,熔石英动态刻蚀的刻蚀速率快于静态刻蚀。动态刻蚀后熔石英表面均方根(RMS)粗糙度和反射面形分别为 < 1 nm和0.46λ,其3倍频透射率先小幅增加后保持稳定,相比初始表面增加约0.1%。而静态刻蚀使得表面RMS粗糙度和反射面形分别增加至~5 nm和0.82λ,其3倍频透射率先基本不变后下降,相比初始表面下降约0.4%。二者损伤阈值呈现明显不同变化规律:静态刻蚀使熔石英损伤阈值先小幅增加约30%后逐渐降低,动态刻蚀使熔石英损伤阈值增加近一倍后保持相对稳定。结果表明,动态刻蚀后熔石英光学元件性能明显优于静态刻蚀。     

化学刻蚀过程中熔石英表面沉积物的形成及其对激光损伤的影响

化学刻蚀是提升熔石英光学元件抗激光损伤性能的重要后处理技术之一,但刻蚀后熔石英表面附着的沉积物对其表面质量、透射性能和抗激光损伤性能有很大影响。使用光学显微镜和原子力显微镜表征了化学刻蚀后附着于熔石英表面的沉积物的微观形貌,并分析了其形成机理;X射线能谱分析表明化学刻蚀后熔石英表面沉积物主要由Fe,Ni,Al等元素的金属盐组成。损伤阈值测试结果表明熔石英表面高密度沉积物区域的损伤阈值明显低于非沉积物区域,沉积物对熔石英光学元件的抗激光损伤性能产生严重影响,它们是诱导熔石英激光损伤的前驱体。     

Improvement of laser damage thresholds of fused silica by ultrasonic-assisted hydrofluoric acid etching

Polished fused silica samples were etched for different durations by using hydrofluoric(HF) acid solution with HF concentrations in an ultrasonic field. Surface and subsurface polishing residues and molecular structure parameters before and after the etching process were characterized by using a fluorescence microscope and infrared(IR) spectrometer, respectively. The laser induced damage thresholds(LIDTs) of the samples were measured by using pulsed nanosecond laser with wavelength of 355 nm. The results showed that surface and subsurface polishing residues can be effectively reduced by the acid etching process, and the LIDTs of fused silica are significantly improved. The etching effects increased with the increase of the HF concentration from 5 wt.% to 40 wt.%. The amount of polishing residues decreased with the increase of the etching duration and then kept stable. Simultaneously, with the increase of the etching time, the mechanical strength and molecular structure were improved.     

激光诱导HF酸刻蚀后熔石英后表面划痕的损伤行为研究

用光学显微镜和原子力显微镜记录HF酸刻蚀后熔石英元件后表面划痕的形貌结构,并利用单脉冲激光对其进行辐照测试,以研究不同结构参数划痕的激光损伤特性.实验结果表明,由于HF酸的腐蚀钝化作用,划痕结构横向截面呈余弦形分布;其初始损伤阈值并非由单一的划痕宽度或深度参数决定,而是与其横向剖面结构的宽深比值密切相关;通过实验得到了二者之间的关系曲线,并采用时域有限差分算法对不同结构参数划痕附近光场分布进行理论模拟,理论场计算得到的增强结果与实验值符合得很好.     

HF酸刻蚀提升熔石英亚表面划痕抗损伤性能的机理

用HF酸刻蚀熔石英元件,研究刻蚀对元件后表面划痕的形貌结构及损伤性能的影响,探索损伤阈值提升的原因.时域有限差分算法理论计算结果表明:对于含有50nm直径氧化锆颗粒的划痕,对入射光调制引发场增强的最大值是入射光强的6.1倍,且最强点位于划痕内部氧化锆颗粒附近,而结构相同但不含杂质的划痕引发的最大场增强为入射光强的3.6倍,最强区位于划痕外围;HF酸刻蚀能够有效去除划痕中的杂质,改变划痕结构,增加其宽深比值,经刻蚀的划痕对入射光调制引发场增强降低到入射光强的2.2倍.实验结果表明,经过深度刻蚀的划痕初始损伤阈值较刻蚀之前提高一倍多;光热弱吸收测试仪测试刻蚀后划痕对1 064nm激光的吸收最大值仅为230ppm.HF酸刻蚀同时可以提升元件整体损伤阈值,由于元件上无缺陷区域损伤阈值随刻蚀的深入先增加后降低,因此HF酸刻蚀应进行到元件损伤阈值提升到最大值为止.     

熔石英表面杂质元素在酸蚀过程中的变化

为了探寻熔石英表面痕量杂质元素种类以及随HF酸蚀刻过程中的变化情况,用质量分数为1%HF酸溶液对熔石英进行长达24,48,72,96 h的静态蚀刻实验。结合飞行时间二次离子质谱（TOF-SIMS）和X射线光电子能谱（XPS）测试分析结果发现,熔石英试片表面的痕量杂质元素主要含有B,F,K,Ca,Na,Al,Zn和Cr元素,其中绝大部分都存在于贝氏层中,在亚表面缺陷层检测到有K,Ca元素。所含有的K,Na杂质元素会与氟硅酸反应生成氟硅酸盐化合物。分析表明,在HF酸蚀刻的过程中一部分杂质元素将被消除,一部分杂质元素和生成氟硅酸盐化合物会随着蚀刻液逐渐从熔石英表面向表面纵深方向扩散并被试片吸附沉积,且随着深度的加深各元素的相对含量逐渐减少。     

熔石英光学元件的损伤前驱及其抑制技术北大核心CSCD

基于抛光所引起的熔石英元件表面、亚表面所存在的损伤前驱体分布,研究了不同种类的损伤前驱体所引起的损伤形貌。然后根据不同种类的损伤前驱体分别采用表面活性剂、强氧化性酸、氢氟酸的水溶液对不同的损伤前驱体进行处理。研究结果显示:经过前期预先清洗以后,吸收性杂质所导致的雾状损伤得以消除,亚表面分布的裂纹得以很好地平滑钝化,极大地提升了熔石英光学元件的抗损伤性能,损伤阈值从4.8J/cm2提高到11.0J/cm2,最大提升幅度达到原来的2.3倍。     

HF酸刻蚀提升熔石英亚表面划痕抗损伤性能的机理

用HF酸刻蚀熔石英元件,研究刻蚀对元件后表面划痕的形貌结构及损伤性能的影响,探索损伤阈值提升的原因.时域有限差分算法理论计算结果表明:对于含有50 nm直径氧化锆颗粒的划痕,对入射光调制引发场增强的最大值是入射光强的6.1倍,且最强点位于划痕内部氧化锆颗粒附近,而结构相同但不含杂质的划痕引发的最大场增强为入射光强的3.6倍,最强区位于划痕外围;HF酸刻蚀能够有效去除划痕中的杂质,改变划痕结构,增加其宽深比值,经刻蚀的划痕对入射光调制引发场增强降低到入射光强的2.2倍.实验结果表明,经过深度刻蚀的划痕初始损伤阈值较刻蚀之前提高一倍多;光热弱吸收测试仪测试刻蚀后划痕对1 064 nm激光的吸收最大值仅为230 ppm.HF酸刻蚀同时可以提升元件整体损伤阈值,由于元件上无缺陷区域损伤阈值随刻蚀的深入先增加后降低,因此HF酸刻蚀应进行到元件损伤阈值提升到最大值为止.     

Experimental investigation of enhancing the subsurface damage threshold of Nd-doped phosphate glass

Experimental investigation was performed with a 1064-nm, 10-ns Nd:YAG laser to determine the effects of the surface hydrogen acid etching on laser damage, compared with damage of conventionally polished surface. The investigation was helpful for us to understand the negative effects of Nd-doped phosphate glass surface and subsurface damage (SSD) on laser induced damage threshold (LIDT). A set of samples was polished, and then chemically etched in a cool buffered 10%HF 20%H2SO4 solution at different times. Another set of samples was ground and etched in the hot-buffered solution, and then polished. All the samples were irradiated with Nd: YAG laser and characterized by optical microscopy. Results of LIDT were obtained according to International standard ISO/DIS 11254-1.2. Chemical treatment can remove the contaminants in the polished re-deposition layer and the SSD for improving the laser damage resistance of Nd-doped phosphate glass surfaces. The method of using hot solution was more effective than that ofusing cool solution.     

Subsurface defect characterization and laser-induced damage performance of fused silica optics polished with colloidal silica and ceria

This paper mainly focuses on the influence of colloidal silica polishing on the damage performance of fused silica optics. In this paper, nanometer sized colloidal silica and micron sized ceria are used to polish fused silica optics. The colloidal silica polished samples and ceria polished samples exhibit that the root-mean-squared(RMS) average surface roughness values are 0.7 nm and 1.0 nm, respectively. The subsurface defects and damage performance of the polished optics are analyzed and discussed. It is revealed that colloidal silica polishing will introduce much fewer absorptive contaminant elements and subsurface damages especially no trailing indentation fracture. The 355-nm laser damage test reveals that each of the fused silica samples polished with colloidal silica has a much higher damage threshold and lower damage density than ceria polished samples. Colloidal silica polishing is potential in manufacturing high power laser optics.     

低亚表面损伤石英光学基底的加工和检测技术

制备低亚表面损伤的超光滑光学基底,是获得高损伤阈值薄膜的前提条件。针对石英材料在不同加工工序中引入亚表面损伤层的差异,首先利用共焦显微成像结合光散射的层析扫描技术,对W10和W5牌号SiC磨料研磨后的亚表面缺陷进行了检测,讨论了缺陷尺寸与散射信号强度、磨料粒径与损伤层深度间的对应关系;同时,采用化学腐蚀处理技术对抛光后样品的亚表面形貌进行了刻蚀研究,分析了化学反应生成物和亚表面缺陷对刻蚀速率的影响、不同深度下亚表面缺陷的分布特征,以及均方根粗糙度与刻蚀深度间的联系。根据各道加工工艺的不同采用了相应的亚表面检测技术,由此来确定下一道加工工序,合理的去除深度,最终获得了极低亚表面损伤的超光滑光学基底。     

Laser etching of fused silica using an adsorbed toluene layer

A new method for laser etching of transparent materials with a low etch rate and a very good surface quality is demonstrated. It is based on the pulsed UV-laser backside irradiation of a transparent material that is covered with an adsorbed toluene layer. This layer absorbs the laser radiation causing the etching of the solid. The threshold fluence for etching of fused silica amounts to 0.7 J/cm². The constant etch rate of about 1.3 nm/pulse that has been observed in a fluence interval from 2 to 5 J/cm² is evidence of a saturated process. The limited thickness of the adsorbed layer causes the low etch rates and the rate saturation. The etched surface structures have well defined edges and low surface roughness values of down to 0.4 nm rms. PACS 81.65.Cf; 81.05.Kf; 79.20.Ds; 61.80.Ba; 42.55.Lt     

光学元件亚表面缺陷的损伤性检测方法

在磨削、研磨和抛光加工过程中产生的微裂纹、划痕、残余应力等亚表面缺陷会导致熔石英元件抗激光损伤能力下降,如何快速、准确地检测亚表面损伤成为光学领域亟待解决的关键问题。采用HF酸蚀刻法、角度抛光法和磁流变斜面抛光法对熔石英元件在研磨加工中产生的亚表面缺陷形貌特征及损伤深度进行了检测和对比分析,结果表明,不同检测方法得到的亚表层损伤深度的检测结果存在一定差异,HF酸蚀刻法检测得到的亚表面损伤深度要比角度抛光法和磁流变斜面抛光法检测结果大一些。且采用的磨粒粒径越大,试件表面及亚表面的脆性断裂现象越严重,亚表面缺陷层深度越大。     

Effect of surface preparation technique on the radiation detector performance of CdZnTe

Synthetic CdZnTe (CZT) semiconducting crystals are highly suitable for the room temperature-based detection of gamma radiation. The surface preparation of Au contacts on surfaces of CZT detectors is typically conducted after (1) polishing to remove artifacts from crystal sectioning and (2) chemical etching, which removes residual mechanical surface damage however etching results in a Te rich surface layer that is prone to oxidize. Our studies show that CZT surfaces that are only polished (as opposed to polished and etched) can be contacted with Au and will yield lower surface currents. Due to their decreased dark currents, these as-polished surfaces can be used in the fabrication of gamma detectors exhibiting a higher performance than polished and etched surfaces with relatively less peak tailing and greater energy resolution.     

超声波辅助酸蚀提高熔石英损伤阈值

为了提高熔石英元件表面抗激光损伤阈值,利用超声波辅助HF酸研究平滑光学元件表面缺陷形貌和去除刻蚀后残留物效果,通过扫描电子显微镜电镜和原子力显微镜记录表面形貌结构,以及单脉冲激光辐照测试抗损伤阈值确定实验参数。研究表明,超声波场的引入能催化HF酸的刻蚀速率、提高钝化效果并且更易剥离嵌入的亚μm级杂质粒子。经过实验测试,获得了熔石英类元件相匹配的超声辅助HF酸刻蚀实验参数,研究结果对应用超声波辅助HF酸研究熔石英表面抗激光损伤有重要意义。     

预处理对355nm激光作用下熔石英损伤增长的影响

测试了经化学蚀刻、紫外激光预处理及其共同处理后的熔石英355 nm激光损伤阈值;研究了处理前后其损伤斑面积随激光辐照脉冲数的增长情况。结果表明,处理后熔石英355 nm激光损伤阈值得到了提高,且损伤斑面积增长变慢。利用CO2激光对熔石英表面损伤点进行了修复处理,修复后的损伤点R-on-1抗损伤阈值和基底阈值相当,损伤增长得到有效抑制。     

杂质诱导熔石英激光的损伤机理

发展了355 nm纳秒激光下亚波长杂质粒子引起熔石英损伤的基本模型。通过Mie散射理论和热传导方程,计算了粒子与熔石英边界处的温度随粒子尺寸的变化关系,并分析了达到临界温度时,不同粒子诱导损伤所需的关键能量密度,讨论了各粒子最易引起熔石英损伤的尺寸。实验采用355 nm纳秒激光脉冲作用熔石英及其HF刻蚀样品,测得两者的损伤概率。研究表明:粒子吸收激光能量,随着粒子半径的增加,其边缘温度先增大后减小,一定尺寸范围内的粒子才会引起熔石英的损伤;关键能量密度所对应的粒子半径为最易引起熔石英损伤的关键粒子半径;经刻蚀后,熔石英样品表面杂质数密度降低,损伤概率降低,损伤阈值提高。