Spectrophotometric determination of cyclotrimethylenetrinitramine (RDX) in explosive mixtures and residues with the Berthelot reaction

On-site colorimetric methods are a valuable, cost-effective tool to assess the nature and extent of contamination in remediated sites and to enable on-site screening for police criminology laboratories. The existing colorimetric method for cyclotrimethylenetrinitramine (RDX) based on a Griess reaction suffers from the non-quantitative reduction to nitrite and from the unstable character of HNO₂ in acidic medium. Thus we propose a novel spectrophotometric RDX assay in explosive mixtures and residues, based on (Zn + HCl) reduction of RDX in a microwave oven, followed by neutralization of the reduction products to ammonia and low molecular-weight amines, and Berthelot reaction of these amine-compounds with phenol and hypochlorite in alkaline medium to give an intensely blue indophenol dye absorbing at 631 nm. The molar absorptivity and limit of detection (LOD) for RDX were (1.08 ± 0.04) × 10⁴ L mol⁻¹ cm⁻¹ and 0.18 mg L⁻¹, respectively. Application of the method to synthetic mixture solutions of RDX and trinitrotoluene (TNT) at varying proportions showed that there was minimal interference from TNT (which could be compensated for by dicyclohexylamine colorimetry), since the Berthelot reaction was essentially non-responsive to m-substituted anilines derived from TNT upon (Zn + HCl) reduction. The proposed method was successfully applied to military-purpose explosive mixtures of (RDX + inert matter) such as Comp A5, Comp C4, and Hexal P30, and to (RDX + TNT) mixtures such as Comp B. The molar absorptivity of RDX was much higher than that of either ammonium or nitrate; RDX could be effectively separated from ammonium and nitrate in soil mixtures, based on solubility differences. The Berthelot method for RDX was statistically validated using Comp B mixtures against standard HPLC equipped with a Hypersil C-18 column with (40% MeOH-60% H₂O) mobile phase, and against gas chromatography-thermal energy analysis (GC-TEA) system.     

Quantification and remote detection of nitro explosives by helium plasma ionization mass spectrometry (HePI‐MS) on a modified atmospheric pressure source designed for electrospray ionization

Helium Plasma Ionization (HePI) generates gaseous negative ions upon exposure of vapors emanating from organic nitro compounds. A simple adaptation converts any electrospray ionization source to a HePI source by passing helium through the sample delivery metal capillary held at a negative potential. Compared with the demands of other He‐requiring ambient pressure ionization sources, the consumption of helium by the HePI source is minimal (20–30 ml/min). Quantification experiments conducted by exposing solid deposits to a HePI source revealed that 1 ng of 2,4,6‐trinitrotoluene (TNT) on a filter paper (about 0.01 ng/mm²) could be detected by this method. When vapor emanating from a 1,3,5‐trinitroperhydro‐1,3,5‐triazine (RDX) sample was subjected to helium plasma ionization mass spectrometry (HePI‐MS), a peak was observed at m/z 268 for (RDX●NO₂)^?. This facile formation of NO₂^? adducts was noted without the need of any extra additives as dopants. Quantitative evaluations showed RDX detection by HePI‐MS to be linear over at least three orders of magnitude. TNT samples placed even 5 m away from the source were detected when the sample headspace vapor was swept by a stream of argon or nitrogen and delivered to the helium plasma ion source via a metal tube. Among the tubing materials investigated, stainless steel showed the best performance for sample delivery. A system with a copper tube, and air as the carrier gas, for example, failed to deliver any detectable amount of TNT to the source. In fact, passing over hot copper appears to be a practical way of removing TNT or other nitroaromatics from ambient air. Copyright © 2012 John Wiley & Sons, Ltd.     

Hierarchically Annular Mesoporous Carbon Derived from Phenolic Resin for Efficient Removal of Antibiotics in Wastewater

Antibiotics have become a new type of environmental pollutant due to their extensive use. High-performance adsorbents are of paramount significance for a cost-effective and environmentally friendly strategy to remove antibiotics from water environments. Herein, we report a novel annular mesoporous carbon (MCN), prepared by phenolic resin and triblock copolymer F127, as a high-performance adsorbent to remove penicillin, streptomycin, and tetracycline hydrochloride from wastewater. The MCNs have high purity, rich annular mesoporosity, a high surface area (605.53 m²/g), and large pore volume (0.58 cm³/g), improving the adsorption capacity and facilitating the efficient removal of penicillin, streptomycin, and tetracycline hydrochloride from water. In the application of MCNs to treat these three kinds of residual antibiotics, the adsorption amounts of tetracycline hydrochloride were higher than penicillin and streptomycin, and the adsorption capacity was up to 880.6 mg/g. Moreover, high removal efficiency (99.6%) and excellent recyclability were achieved. The results demonstrate that MCN adsorbents have significant potential in the treatment of water contaminated with antibiotics.     

Effective Removal of Nitrotoluene Compounds from Aqueous Solution Using Magnetic-Activated Carbon Nanocomposites (<Emphasis Type="Italic">m</Emphasis>-Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>@ACCs)

In this study, regular-shaped magnetic-activated carbon nanocomposite (m-Fe₃O₄@ACCs) was synthesized and characterized with X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and the vibrating sample magnetometer (VSM) and was used as adsorbents for the removal of nitrotoluene compounds (NTCs) from water and industrial wastewater. The effective parameters on adsorption process, such as solution pH, shaking speed, contact time, and adsorbent dosage were optimized and the optimum amounts were 7 300 rpm, 10 min, and 1.2 g L^–1, respectively. The contact time and adsorbent dosage are dependent parameters and hence were studied simultaneously. The results showed no significant loss in the adsorption capacity, and the adsorption efficiency of m-Fe₃O₄@ACCs could still be 90% in the 9th cycle. The equilibrium adsorption isotherm followed the Langmuir isotherm model describes the monolayer adsorption of NTCs on m-Fe₃O₄@ACCs, and the maximum adsorption capacities (q_m) for 2-nitrotolouene, 2,6-dinitrotoluene, 2,4-dinitrotoluene, and 3,4-dinitrotoluene were found to be 144.93, 142.86, 166.67, and 153.85 mg g^?l, respectively. The proposed process was successfully applied for the removal of NTCs from tap water and nitration process wastewater.     

Fabrication of titanate nanotubes/iron oxide magnetic composite for the high efficient capture of radionuclides: a case investigation of 109Cd(II)

In this paper, the capture of radiocadmium (Cd(II)) by adsorption onto the titanate nanotube/iron oxide (TNT/IOM) magnetic composite as a function of contact time, pH, ionic strength, foreign cation and anion ions, humic acid (HA) and fulvic acid (FA) was studied using batch technique. The results indicated that the adsorption of Cd(II) onto the TNT/IOM magnetic composite was dependent on ionic strength at pH <9.0, but was independent of ionic strength at pH >9.0. Outer-sphere surface complexation were the main mechanism of Cd(II) adsorption onto the TNT/IOM magnetic composite at low pH values, whereas the adsorption was mainly dominated via inner-sphere surface complexation at high pH values. The adsorption of Cd(II) onto the TNT/IOM magnetic composite was dependent on foreign cation and anion ions at low pH values, but was independent of foreign cation and anion ions at high pH values. A positive effect of HA/FA on Cd(II) adsorption onto the TNT/IOM magnetic composite was found at low pH values, while a negative effect was observed at high pH values. From the results of Cd(II) removal by the TNT/IOM magnetic composite, the optimum reaction conditions can be obtained for the maximum removal of Cd(II) from water. It is clear that the best pH values of the system to remove Cd(II) from solution by using the TNT/IOM magnetic composite are 7.0–8.0. Considering the low cost and effective disposal of Cd(II)-contaminated wastewaters, the best condition for Cd(II) capture by the TNT/IOM magnetic composite is at room temperature and solid content of 0.5 g L^?1. These results are quite important for estimating and optimizing the removal of Cd(II) and related metal ions by the TNT-based magnetic composite.     

Selective spectrophotometric determination of TNT in soil and water with dicyclohexylamine extraction

Contaminated land and groundwater remediation in military waste dumping sites often necessitates the use of simple, cost-effective, and rapid tests for detecting trinitrotoluene (TNT) residues in the field along with their dinitro-analogues. A simple, rapid, low-cost, and field-adaptable (on-site) colorimetric method was developed for quantifying TNT in the presence of RDX, PETN, picric acid, 2,4-DNT (dinitrotoluene), dinitrophenol, and dinitroaniline. Most commercialized methods for TNT assay-with the exception of Cold Regions Research and Engineering Laboratory of the U.S. Army (CRREL) method-use proprietary chemicals, and the color stability and intensity are highly dependent on the composition of the organic solution comprised of acetone or methanol. The developed colorimetric method is based on the extraction of TNT from water-acetone solution into an organic solvent mixture of dicyclohexylamine (DCHA)-isobutyl methyl ketone (IBMK) (10:1, v/v), filtration through a filter paper into a stoppered optical cell containing anhydrous sodium sulfate, and measurement of the absorbance of the organic extract at 531 nm after 5 min. The red-violet color of the extract was due to intermolecular charge-transfer (CT) between the electron attracting TNT and electron-donating DCHA, and the molar absorptivity for TNT in final organic solution was (1.16 ± 0.02) × 10⁴ L mol⁻¹ cm⁻¹.The R.S.D. of the slope of calibration line was 0.7%. The LOD of the method in the final organic phase was 0.38 μM TNT, and LOD values expressed on the basis of original soil TNT content were 0.5, 1.3, and 1.5 ppm (μg g⁻¹) for clay, loamy clay, and sandy soils, respectively. Unlike other spectrophotometric methods, the developed assay was basically tolerant to common cations and anions found in soil and water at 100-fold weight ratios, and to soil humic acids. Among a number of compounds that may be encountered in polynitro-explosive storage and waste reclaimation sites such as picric acid, dinitrophenol, 2,4-dinitrotoluene, dinitroaniline, RDX, PETN, and tetryl, only tetryl interfered with the developed TNT assay. Water tolerance and exploitability over a wide pH range were other superiorities over the CRREL method. The CT-complex was relatively stable, as the absorbance of the organic extract was not significantly influenced from the dilution of the water-acetone phase. Aside from the extractive-photometric procedure established for aqueous solutions, a simulated field colorimetric assay for TNT directly applicable to soil was also devised, based on direct color development in a 4:1 (v/v) acetone-dicyclohexylamine organic extract of soil at a liquid-to-solid ratio of 5 mL g⁻¹.     

Analysis of 2,4,6-trinitrotoluene, pentaerythritol tetranitrate and cyclo-1,3,5-trimethylene-2,4,6-trinitramine using negative corona discharge ion mobility spectrometry

In this study, the capability of negative corona discharge ion mobility spectrometry (IMS) for quantitative magnitude of several explosives including 2,4,6-trinitrotoluene (TNT), pentaerythritol tetranitrate (PETN) and cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX) has been evaluated for the first time. The total current obtained with the negative corona discharge was about 100 times larger than that of IMS based on ⁶³Ni, which results in a lower detection limit and a wider linear dynamic range. The detection limits for PETN, TNT and RDX were 8×10⁻¹¹, 7×10⁻¹¹ and 3×10⁻¹⁰ g, respectively. The calibration plots for these explosives showed linear dynamic ranges of about four orders of magnitude.     

Adsorption of Dyes from Aqueous Textile By-Products on Activated Carbon from Scenedesmus obliquus

The adsorption of activated carbon prepared from Scenedesmus obliquus (algae) was evaluated through adsorption of Astrazon red. The adsorption efficiency of activated carbon was determined based on the specific surface area and pore size distribution. These results were compared with the results obtained with untreated algae. Approximately a 3-fold increase in the percentage of dye removal was observed for activated carbon compared to the untreated material. The primary reason for this observation may be the increase in specific surface area and total pore volume by chemical activation from 0.0136 to 423.7001?m²?g^?1 and from 0.0012 to 0.1643?cm³?g^?1, respectively. A pseudo-second-order model was fit with the kinetic data and the results indicate chemical adsorption. The maximum adsorption capacity of activated carbon was 181.82?mg?g^?1 at 25°C according to Langmuir isotherm model.     

Improved Adsorption of the Toxic Herbicide Diuron Using Activated Carbon Obtained from Residual Cassava Biomass (Manihot esculenta)

The production and consumption of cassava (Manihot esculenta) occur in several places worldwide, producing large volumes of waste, mostly in the form of bark. This study sought to bring a new purpose to this biomass through producing activated carbon to use as an adsorbent to remove the herbicide Diuron from water. It was observed that the carbon contains the functional groups of methyl, carbonyl, and hydroxyl in a strongly amorphous structure. The activated carbon had a surface area of 613.7 m² g⁻¹, a pore volume of 0.337 cm³ g⁻¹, and a pore diameter of 1.18 nm. The Freundlich model was found to best describe the experimental data. It was observed that an increase in temperature favored adsorption, reaching a maximum experimental capacity of 222 mg g⁻¹ at 328 K. The thermodynamic parameters showed that the adsorption was spontaneous, favorable, and endothermic. The enthalpy of adsorption magnitude was consistent with physical adsorption. Equilibrium was attained within 120 min. The linear driving force (LDF) model provided a strong statistical match to the kinetic curves. Diffusivity (D_s) and the model coefficient (K_LDF) both increased with a rise in herbicide concentration. The adsorbent removed up to 68% of pollutants in a simulated effluent containing different herbicides. Activated carbon with zinc chloride (ZnCl2), produced from leftover cassava husks, was shown to be a viable alternative as an adsorbent for the treatment of effluents containing not only the herbicide Diuron but also a mixture of other herbicides.     

Adsorption of cationic methylene blue dye using microwave-assisted activated carbon derived from acacia wood: Optimization and batch studies

This study assesses the performance of optimized acacia wood-based activated carbon (AWAC) as an adsorbent for methylene blue (MB) dye removal in aqueous solution. AWAC was prepared via a physicochemical activation process that consists of potassium hydroxide (KOH) treatment, followed by carbon dioxide (CO₂) gasification under microwave heating. By using response surface methodology (RSM), the optimum preparation conditions of radiation power, radiation time, and KOH-impregnation ratio (IR) were determined to be 360 W, 4.50 min, and 0.90 g/g respectively, which resulted in 81.20 mg/g of MB dye removal and 27.96% of AWAC’s yield. Radiation power and IR had a major effect on MB dye removal while radiation power and radiation time caused the greatest impact on AWAC’s yield. BET surface area, mesopore surface area, and pore volume of optimized AWAC were found to be 1045.56 m²/g, 689.77 m²/g, and 0.54 cm³/g, respectively. Adsorption of MB onto AWAC followed Langmuir and pseudo-second order for isotherm and kinetic studies respectively, with a Langmuir monolayer adsorption capacity of 338.29 mg/g. Mechanism studies revealed that the adsorption process was controlled by film diffusion mechanism and indicated to be thermodynamically exothermic in nature.     

Development and tailoring of amino-functionalized activated carbon based Cucumerupsi manni Naudin seed shells for the removal of nitrate ions from aqueous solution

The removal of nitrate ions with ethylenediamine (EDA)-functionalized activated carbon (AC-NH₂) was studied in this work. Activated carbon prepared from Cucumerupsi manni Naudin seed shells using ZnCl₂ (ACZ) was functionalized with EDA via a nitric acid oxidation followed by acyl chlorination and amidation process. The effect of pH, contact time, initial concentration and co-existing ions on the adsorption of nitrate ions have been investigated. The FTIR and elemental analysis revealed that amino groups were successfully grafted onto the ACZ after functionalization. The surface area and average pore of ACZ were found to be 1008.99 m²/g and 2.02 nm respectively. However, it was noticed that, after functionalization (AC-NH₂), its surface area decreases to 113.43 m²/g meanwhile, its pore diameter increases to 2.48 nm. The experimental results of adsorption showed that AC-NH₂ exhibit excellent nitrate ions uptake performance compared to ACZ which is attributed to the presence of the grafted amino groups on the ACZ. Nitrate adsorption follows pseudo-first-order kinetic model while the equilibrium adsorption data was best fitted the Freundlich isotherm suggesting that the adsorption process was predominated by physisorption. This study demonstrates that the prepared AC-NH₂ is a promising adsorbent for nitrate ions removal from aqueous media.     

Determination of TNT and its metabolites in water samples by voltammetric techniques

Square-wave voltammetry with the hanging drop mercury electrode as the working electrode was used for the determination of ultratraces of explosives in aqueous solution. It was shown that the strong pressure dependence of the pneumatically controlled multimode electrode system of a conventional Metrohm apparatus could be compensated by an additional pressure regulation, through which the pressure variations could be decreased when switching from deaeration to the static measurements. By using square-wave voltammetry with this electrode system after this modification the limits of detection for 2,4,6-trinitrotoluene (TNT) and other TNT-metabolites could be decreased down to 0.2 μg L⁻¹ when using a measurement time of 6 min. Also a simultaneous determination of TNT and hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) was shown to be possible over a wide linear range and the detection limits then were 2.2 μg L⁻¹ for TNT and 25 μg L⁻¹ for RDX. By applying the highly stable and adjustable pressure as mentioned before, the calibrations could be kept stable over a period of up to 1 week.     

Micellar extraction and high performance liquid chromatography-ultra violet determination of some explosives in water samples

An analytical method based on the cloud point extraction combined with high performance liquid chromatography is used for the extraction, separation and determination of four explosives; octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazine (HMX), hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), 2,4,6-trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN). These compounds are extracted by using of Triton X-114 and cetyl-trimethyl ammonium bromide (CTAB). After extraction, the samples were analyzed using a HPLC-UV system. The parameters affecting extraction efficiency (such as Triton X-114 and CTAB concentrations, amount of Na₂SO₄, temperature, incubation and centrifuge times) were evaluated and optimized. Under the optimum conditions, the preconcentration factor was 40 and the improvement factors of 34, 29, 61 and 42 with detection limits of 0.09, 0.14, 0.08 and 0.40 (μg L⁻¹) were obtained for HMX, RDX, TNT and PETN, respectively. The proposed method was successfully applied to the determination of these compounds in water samples and showed recovery percentages of 97-102% with RSD values of 2.13-4.92%.     

Ultrafast Removal of Cadmium(II) by Green Cyclodextrin Metal–Organic‐Framework‐Based Nanoporous Carbon: Adsorption Mechanism and Application

Water contaminated with heavy metals has been identified as a significant threat to human health. Therefore, the development of safe and rapid water‐treatment techniques is necessary. We have synthesized an eco‐friendly γ‐cyclodextrin metal–organic framework (MOF)‐based nanoporous carbon (γ‐CD MOF‐NPC) material, conducted a comprehensive characterization of it, and found its rapid and effective Cd^II‐removal capacity. The γ‐CD MOF‐NPC could effectively sequester a majority of cadmium ions within one minute, and it still demonstrated excellent adsorption ability under various conditions, including different pH, adsorbent dosage, and coexistent ions. The maximum adsorption capacity was calculated to be 140.85 mg g^?1 by means of the Langmuir model. The adsorption was primarily due to the effect of ion exchange of oxygen‐containing functional groups, as determined by studying the ζ potential and Fourier transform infrared spectroscopy. Flow‐through experiments further proved the rapid Cd^II‐removal capacity and potential of the practical application of γ‐CD MOF‐NPC in water treatment according to the cytotoxic data.     

Single-stage microwave assisted coconut shell based activated carbon for removal of Zn(II) ions from aqueous solution – Optimization and batch studies

Health and environmental issues associated with heavy metal ions have received serious attention from communities worldwide. This work explores the potential of coconut shell as activated carbon (CSAC), in adsorbing zinc, Zn(II) ions. This adsorbent was prepared via a single-stage microwave irradiation technique under the flow of carbon dioxide, CO₂ gas. CSAC posed BET surface area of 625.61 m²/g, 513.25 m²/g of mesopores surface area, total pore volume of 0.42 cm³/g, and average pore diameter of 4.55 nm. Zeta potential distribution on CSAC was found to be ?21 mV. Response surface methodology (RSM) had suggested that the optimum values of variables were 450 W and 3.17 min for radiation power and radiation time respectively, which resulted in 69.65% of Zn(II) removal and 44.32% of CSAC’s yield. Based on F-value, radiation power (473.62) and radiation time (140.50) posed major and moderate effects on Zn(II) removal, respectively. Meanwhile, CSAC’s removal was significantly affected by radiation power (78.84) and less affected by radiation time (7.06). In a batch study, when the initial concentration of Zn(II) was increased, Zn(II) uptakes increased as well. On contrary, Zn(II) removal percentage decreased with the increase of Zn(II)’s initial concentration. Multilayer adsorption of Zn(II) onto CSAC had occurred since this adsorption system followed Freundlich isotherm the best, and the monolayer adsorption capacity, Q_m for Zn(II) was revealed to be 7.87 mg/g. The kinetic data of the Zn(II)-CSAC adsorption system was best described by pseudo-first-order (PFO) which indicated the role of physisorption. In the regeneration study, CSAC’s mass and Zn(II) adsorption uptakes had reduced from 100% to 37% and 77%, respectively, after 6 regeneration cycles.     

Selective and Efficient Removal of Fluoride from Water: In Situ Engineered Amyloid Fibril/ZrO2 Hybrid Membranes

We report a new strategy for efficient removal of F^? from contaminated water streams, and it relies on carbon hybrid membranes made of amyloid fibril/ZrO₂ nanoparticles (<10 nm). These membranes exhibit superior selectivity for F^? against various competitive ions, with a distribution coefficient (K_d) as high as 6820 mL g^?1, exceeding commercial ion‐exchange resins (IRA‐900) by 180 times and outdoing the performance of most commercial carbon‐activated aluminum membranes. At both low and high (ca. 200 mg L^?1) F^? concentrations, the membrane efficiency exceeds 99.5 % removal. For real untreated municipal tap water (ca. 2.8 mg L^?1) under continuous operating mode, data indicates that about 1750 kg water m^?2 membrane can be treated while maintaining drinking water quality, and the saturated membranes can be regenerated and reused several times without decrease in performance. This technology is promising for mitigating the problem of fluoride water contamination worldwide.     

A new one-dimensional coordination polymer synthesized from zinc and guanazole: Superior capture of organic arsenics

Organic arsenic compounds in the environment are a global threat to human health. This threat has created the urgency to develop highly efficient adsorbents with both high adsorption capacity and versatile removal of different arsenic compounds. A novel 1D zinc(II) coordination polymer, formulated as Zn₂(datrz)₂(bpy)Cl₂ ( BUC-70 ) (datrz = guanazole, bpy = 4,4′-bipyridine), was successfully synthesized through slow evaporation at room temperature. BUC-70 exhibited an excellent adsorption capacity toward p-arsanilic acid (p-ASA) and roxarsone (ROX) in water, which could be ascribed to As–O–Zn bonding interactions and strong hydrogen-bonding interactions between the organic arsenics and BUC-70 . The maximum adsorption capacities toward p-ASA and ROX were 738 and 937 mg·g⁻¹, respectively. BUC-70 was effective in the removal of p-ASA and ROX at low concentrations (<5 mg·l⁻¹) from the simulated p-ASA and ROX wastewater. Furthermore, the as-synthesized BUC-70 exhibited good adsorption property toward p-ASA and ROX in wastewater simulated by lake water and tap water. After adsorptive treatment using BUC-70 , the concentrations of both p-ASA and ROX were lower than the required concentrations of the drinking water standard of the World Health Organization and the surface water standard of China. Continuous-flow, fixed-bed column experiments were performed using BUC-70 loaded on cotton as packing material to explore the potential large-scale application.     

Membrane for in situ optical detection of organic nitro compounds based on fluorescence quenching

Fluorescent membrane formulations for detecting organic nitro compounds by fluorescence quenching were evaluated. The most sensitive membrane is prepared by solvent casting from cyclohexanone to incorporate pyrenebutyric acid into cellulose triacetate plasticized with isodecyl diphenylphosphate. The response follows the Stern-Volmer law for 2,4,6-trinitrotoluene (TNT) and 2,4-dinitrotoluene (DNT). The membrane also responds to hexahydro-1,3,5-tri- nitro-1,3,5-triazine (RDX). For a given set of conditions, the primary factor determining sensitivity is the extent to which each nitro compound partitions into the membrane. Detection limits are ca. 2 mg l^?1 for DNT and TNT and 10 mg l^?1 for RDX. Nitrogen purging prior to the measurement enhances the sensitivity and eliminates interference from oxygen. The membrane is designed to be used for remote optical in situ screening of groundwater for contamination by explosives.     

Polyethyleneimine/activated carbon paper-based material for low-concentration hexavalent chromium removal

Activated carbon paper-based materials were prepared from softwood pulp, activated carbon powder, and polyester fiber through wet forming process. Then polyethyleneimine was loaded on the activated carbon paper-based materials using physical impregnation method to fabricate green, low cost, and degradable PEI/activated carbon composite paper-based adsorbent materials (PPCA) for the removal of Cr(VI) from drinking water. The surface characteristics of the adsorbent were analyzed by SEM, EDX, BET, FT-IR, and XPS. It was found that the maximum adsorption capacity of Cr(VI) could reach up to 1.58 mg g^?1 when the PEI immersion concentration is 1%, the contact time is 180 min, the temperature is 30 °C and pH?=?2. The adsorption of Cr(VI) on PPCA conformed to both the freundlich isotherm model and the quasi-second-order kinetic model, indicating that the adsorption was multi-molecular layer adsorption controlled by chemical reaction process. The adsorption mechanism of Cr(VI) on PPCA included electrostatic attraction, redox and chelation. Overall, this study provides a green, large-scalable production way for the preparation of biodegradable adsorption materials for the efficient removal of Cr(VI) from drinking water aiding the safe management of aqueous system.

Graphical abstract

     

Selective spectrophotometric determination of TNT using a dicyclohexylamine-based colorimetric sensor

Because of the extremely heterogeneous distribution of explosives in contaminated soils, on-site colorimetric methods are efficient tools to assess the nature and extent of contamination. To meet the need for rapid and low-cost chemical sensing of explosive traces or residues in soil and post-blast debris, a colorimetric absorption-based sensor for trinitrotoluene (TNT) determination has been developed. The charge-transfer (CT) reagent (dicyclohexylamine, DCHA) is entrapped in a polyvinylchloride (PVC) polymer matrix plasticised with dioctylphtalate (DOP), and moulded into a transparent sensor membrane sliced into test strips capable of sensing TNT showing an absorption maximum at 530 nm when placed in a 1-mm spectrophotometer cell. The sensor gave a linear absorption response to 5-50 mg L⁻¹ TNT solutions in 30% aqueous acetone with limit of detection (LOD): 3 mg L⁻¹. The sensor is only affected by tetryl, but not by RDX, pentaerythritoltetranitrate (PETN), dinitrotoluene (DNT), and picric acid. The proposed method was statistically validated for TNT assay against high performance liquid chromatography (HPLC) using a standard sample of Comp B. The developed sensor was relatively resistant to air and water, was of low-cost and high specificity, gave a rapid and reproducible response, and was suitable for field use of TNT determination in both dry and humid soil and groundwater with a portable colorimeter.