Micro-preparative operation of high speed column-liquid chromatography in chemical analysis

Summary In the analytical application of column-liquid chromatography the batchwise collection of effluent must be applied if the analytical measurements cannot be carried out in the effluent stream of the chromatographic column. In high pressure liquid chromatography a component may be eluted in a few seconds in a volume of less than hundred microliter. The design of an automatic fraction collector which meets these requirements is described. The batchwise collection of fractions of the column effluent is discussed with respect to fraction volume and additional mixing effects. The application was demonstrated in off-line identification by mass spectrometry, quantitative trace analysis using off-line detection and trace analysis by discontinuous recycling.

---

Mikropräparative Säulen-Flüssigkeits-Chromatographie hoher Geschwindigkeit in der chemischen Analyse

Zusammenfassung Bei der analytischen Anwendung der Säulen-Flüssigkeits-Chromatographie muß die Sammlung des Eluats schubweise erfolgen, wenn die Messungen nicht on-line am Ausgang der Säule vorgenommen werden können. Bei der Hochdruck-Flüssigkeits-Chromatographie kann eine Komponente innerhalb weniger Sekunden in einem Volumen von weniger als 100 l eluiert werden. Ein dafür geeigneter automatischer Fraktionssammler wird beschrieben. Die schubweise Sammlung der Fraktionen wird mit Bezug auf Volumen und zusätzliche Mischeffekte diskutiert. Die Anwendung wird gezeigt an Hand der off-line-Identifizierung durch Massenspektrometrie, der quantitativen Spurenanalyse mit off-line-Erfassung sowie der Spurenanalyse durch diskontinuierlich wiederholte Chromatographie.

Lecture presented at Euroanalysis I Conference, 28. 8.–1. 9. 1972 in Heidelberg, Germany     

Fast and high resolution analysis of human serum transferrin by high performance isoelectric focusing in capillaries

Human serum transferrin is a mixture of isoforms (isoproteins) having different amounts of carbohydrates. Each isoform may exist in iron-free and iron-complexed molecular form. The genetic variations in different populations increase the number of combinations of the different forms of transferrin. To resolve the many components in transferrin preparations, the new high performance capillary technique was employed for isoelectric focusing. Iron-free transferrin and transferrin samples of known iron content were examined. The above method gives an exceptionally rapid analysis (within 15-25 min) of small amounts of samples (less than 1 microgram protein) and as good as or better resolution than other isoelectric focusing techniques previously used for transferrin analysis. By monitoring the focused protein zones at both 280 and 460 nm the molecular forms of transferrin (iron-free, monoferric and differic complexes) can easily be identified. Both steps of isoelectric focusing in capillaries (i.e., prefocusing and mobilization) can be used for analysis. We observed that chelating agents (e.g., carrier ampholytes, nitrilotriacetate) may release iron from microsyringes having metal pistons causing the formation of iron-transferrin complexes.     

Supercritical fluid extraction of PCBs in tandem with high resolution gas chromatography in environmental analysis

A simple method has been developed for the direct coupling of supercritical fluid extractions (SFE) with a high resolution gas chromatograph (HRGC) equipped with an electron capture detector (ECD). SFE conditions have been investigated for polychlorinated biphenyls (PCBs) from sediments in terms of mobile phase, entrainer, pressure, temperature, and mass-flow through the extractor. Dynamic leaching and static steady-state extractions were compared. Extraction efficiencies of up to 100% in less than 15 minutes have been obtained. The extracted PCBs are quantitatively transferred into a fused silica open tubular column (OTC). Determination of PCBs was tested on certified sediment from National Water Research Institute and the results agreed well with certified values.     

High resolution chromatography of ribonucleosides and its application to RNA analysis

A simple and precise method was developed for the separation of nucleosides including modified nucleosides and oligonucleotides. Nineteen kinds of nucleosides were completely separated by HPLC using an ODS column (TSK-gel ODS 80TM) and aqueous mobile phases. The RNA molecule was digested by base restrictive RNase (RNase A, RNase T1) and the digests were separated chromatographically into each oligonucleotide. The nucleoside composition of an oligonucleotide was then determined by this analytical system. It is thus possible to fit the oligonucleotide in the original RNA molecule by using modified bases as markers. The reaction site of quinacrine mustard for tRNA(Phe) (from yeast) could be determined by this analytical system.     

Enantiomeric separation by using nano-liquid chromatography with on-column focusing

The present study shows a new nano-liquid chromatographic method for beta-blocker enantiomers' separation. This method consists of using a capillary column packed with silica particles which were chemically modified with vancomycin. On-column focusing allowed to inject relatively high sample volumes (1500 nL) increasing method sensitivity. The studied racemic compounds, namely atenolol, propranolol, oxprenolol, and metoprolol were dissolved in methanol and injected for chromatographic separation. The effect of injected sample volume was studied in the range of 50-2100 nL. Peak height of the two alprenolol enantiomers increased linearly up to 1500 nL. This volume was injected for validation and sample analysis. Under optimal experimental conditions, LODs and LOQs (LOD and LOQ for each alprenolol enantiomers) were 9.0 and 15.6 ng/mL, respectively. Calibration curves were linear in the studied range (9-250 ng/mL). The optimized method was applied to the analysis of a human plasma sample spiked with racemic alprenolol.     

Limits in arson debris analysis by capillary column gas chromatography/mass spectrometry

Sample enrichment technology and instrumental sensitivity are no longer limiting factors in arson debris analysis. When pyrolyzed, petroleum based composite materials may produce artifacts. Urban air is another major source of interference since some of the components typically found in air, in particular alkylated aromatic hydrocarbons, are customarily used as indicators for the presence of gasoline. It is suggested to replace qualitative analysis with a quantitative approach, taking the sample matrix into consideration.     

Fibre optical scanning with high resolution in thin-layer chromatography

In this paper a high-performance thin-layer chromatography (HPTLC) scanner is presented in which a special fibre arrangement is used as HPTLC plate scanning interface. Measurements are taken with a set of 50 fibres at a distance of 400 to 500 microm above the HPTLC plate. Spatial resolutions on the HPTLC plate of better than 160 microm are possible. It takes less than 2 min to scan 450 spectra simultaneously in a range of 198 to 610 nm. The basic improvement of the item is the use of highly transparent glass fibres which provide excellent transmission at 200 nm and the use of a special fibre arrangement for plate illumination and detection.     

High speed liquid chromatography with small bore columns

Using a specially designed column system, we have systematically investigated the effect of mobile phase velocity on column efficiency. The performance of small bore columns operated at different linear velocities of mobile phase was examined for three different types of injection system. Using the value of H^∞/u or n^∞/t${}_{\text{r}}^{\text{º}}$ as a criterion of a high speed separation, we calculated values of n/t${}_{\text{r}}^{\text{º}}$ for different solutes according to the equation \documentclass{article}\pagestyle{empty}\begin{document}$ {{\rm n}\mathord{\left/ {\vphantom {{\rm n} {{\rm t}_{\rm r}^ \circ }}}\right. \kern-\nulldelimiterspace} {{\rm t}_{\rm r}^ \circ }} = {{{\rm n}^\infty } \mathord{\left/ {\vphantom {{{\rm n}^\infty } {{\rm t}_{\rm r}^ \circ }}} \right. \kern-\nulldelimiterspace} {{\rm t}_{\rm r}^ \circ }}\left({\frac{{1 + {\rm k'}}}{{{\rm k' + }\beta }}} \right)^2 $\end{document}; the results obtained are in agreement with the experimentally determined values. These systematic investigations culminated in the separation of seven compounds in less than 10 s; the respective chromatogram is shown.     

High resolution synchrotron spectroscopy with and without magnetic fields

We present recent experimental work on atomic and molecular spectra in the vacuum ultraviolet and soft X-ray ranges, including magneto-rotation spectra of atoms in high fields and MCD spectra of matrix isolated species. New studies with a double crystal monochromator recently installed in Bonn are described.     

Limits of multi-linear gradient optimisation in reversed-phase liquid chromatography

The concept of limiting peak purity was applied to quantify the degree of completion of the separation capability of a chromatographic system using multi-linear gradients. The objective was to check whether the complexity of a gradient program deserves be increased to enhance resolution by inserting more linear segments, or on the contrary, no significant improvements can be expected under more complex gradients. A set of 19 isoindole derivatives of primary amino acids was selected to test the performance of isocratic, single linear and multi-linear gradients. Accurate simulated chromatograms were obtained via numerical integration of the general equation of gradient elution, using pre-established start and end conditions of the gradient program. The overall peak purity was selected as objective function. Good--although not baseline--resolution was achieved with an optimal trilinear gradient. Excellent agreement between experimental and predicted optimal chromatograms was found. With the proposed approach, a degree of completion of the separation capability of the chromatographic system of 21.2, 49.7, 81.5 and 88.5% was accomplished with optimal gradients with one, two, three and four segments, respectively. More complex gradients did not enhance the latter figure significantly. Also, multi-linear gradients gave rise to more benefits than complementary gradients.     

Quantitative analysis of essential oils in perfume using multivariate curve resolution combined with comprehensive two-dimensional gas chromatography

The use of multivariate curve resolution (MCR) to build multivariate quantitative models using data obtained from comprehensive two-dimensional gas chromatography with flame ionization detection (GC × GC-FID) is presented and evaluated. The MCR algorithm presents some important features, such as second order advantage and the recovery of the instrumental response for each pure component after optimization by an alternating least squares (ALS) procedure. A model to quantify the essential oil of rosemary was built using a calibration set containing only known concentrations of the essential oil and cereal alcohol as solvent. A calibration curve correlating the concentration of the essential oil of rosemary and the instrumental response obtained from the MCR-ALS algorithm was obtained, and this calibration model was applied to predict the concentration of the oil in complex samples (mixtures of the essential oil, pineapple essence and commercial perfume). The values of the root mean square error of prediction (RMSEP) and of the root mean square error of the percentage deviation (RMSPD) obtained were 0.4% (v/v) and 7.2%, respectively. Additionally, a second model was built and used to evaluate the accuracy of the method. A model to quantify the essential oil of lemon grass was built and its concentration was predicted in the validation set and real perfume samples. The RMSEP and RMSPD obtained were 0.5% (v/v) and 6.9%, respectively, and the concentration of the essential oil of lemon grass in perfume agreed to the value informed by the manufacturer. The result indicates that the MCR algorithm is adequate to resolve the target chromatogram from the complex sample and to build multivariate models of GC × GC-FID data.     

Rapid analysis of food products by means of high speed gas chromatography

Since the invention of GC, there has been an ever increasing interest within the chromatographic community for faster GC methods. This is obviously related to the fact that the number of samples subjected to GC analysis has risen greatly. Nowadays, in routine analytical applications, sample throughput is often the most important aspect considered when choosing an analytical method. Gas chromatographic instrumentation, especially in the last decade, has been subjected to continuous and considerable improvement. High-speed injection systems, electronic gas pressure control, rapid oven heating/cooling and fast detection are currently available in a variety of commercial gas chromatographs. The main consequence of this favourable aspect is that high-speed GC is being increasingly employed for routine analysis in different fields. Furthermore, the employment of dedicated software makes the passage from a conventional to a fast GC method a rather simple step. The present review provides an overview of the employment of fast GC techniques for the analysis of food constituents and contaminants. A brief historical and theoretical background is also provided for the approaches described.     

Simultaneous resolution of overlapping peaks in high-performance liquid chromatography and micellar electrokinetic chromatography with diode array detection using augmented iterative target transformation factor analysis

In this paper, augmentation has been applied to data matrices, which originate from hyphenated methods that share the same mode of detection, but use different separation methods, HPLC-DAD and MEKC-DAD. A novel method, wavelength shift eigenstructure tracking (WET), has been proposed for the alignment between the wavelength scale of both detectors. WET proves to be suitable for the detection as well as correction of wavelength shift between both detectors. After correction of the wavelength scale, data obtained on both systems have been augmented and submitted to iterative target transformation factor analysis. Augmented curve resolution provides significantly better estimates of the chromatographic and electrophoretic profiles and spectra than the use of non-augmented curve resolution on HPLC and MEKC data separately. It is particularly useful when the pure fraction of a chromatographic peak is less than 0.10. Finally, the relative weight of MEKC versus HPLC in augmentation may be increased using intensity and noise normalisation. However, since noise normalisation and its accompanying decrease in signal-to-noise ratio leads to a loss of information, and, since intensity normalisation may cause a failure of the augmented curve resolution algorithm, benefits and drawbacks of normalisation should be weighed on a case-by-case basis.     

Non-ideal effects in linear chromatography

Summary A previously developed, simple procedure for computer simulation has been applied to non-ideal, linear chromatography. Relations between three different retention measures (the maximum of the peak, the median and the center of gravity) and the skew and the width of the observed elution peak have been suggested from the results of the simulation. These relations are experimentally verified. No one of the retention measures mentioned above is exactly equal to the thermodynamically correct retention volume, but the discrepancy for the median is the smallest.     

Optimization of resolution in micellar electrokinetic chromatography

A comparison of separations conducted in sodium dodecyl sulfate (SDS) and SDS modified with Brij 35 indicates that selectivity, in Micellar Electrokinetic Chromatography (MEKC), is governed by the composition of the micellar phase. Beyond selectivity optimization, resolution may be improved by increasing efficiency or decreasing electroosmotic flow. Of these approaches, increasing capillary length (to improve efficiency) should be a more time effective means of improving separation.     

Multiplex advantage and peak resolution in correlation chromatography

The multiplex advantage in correlation chromatography not only makes the signal-to-noise ratio better than that of conventional chromatography, but also improves the peak resolution for the same signal-to-noise ratio. This property is demonstrated for the headspace analysis of components from an ethylene-propylene copolymer. The disadvantageous sample dilution in the pneumatic Deans-type switch is discussed.     

Considerations of speed and efficiency in capillary gas chromatography

The analysis time for a given resolution is a complex function of stationary phase selectivity, column radius, and thickness of the stationary phase film. Variation of these parameters has a large effect not only on analysis time, but also on the column inlet pressure and other instrumental requirements. The minimum amount that can be reliably detected as well as the maximum sample capacity of a column are strongly related to the selected column dimensions.     

Multicomponent self-modelling curve resolution in high-performance liquid chromatography by iterative target transformation analysis

Iterative target transformation factor analysis can provide a method for resolving elution profiles consisting of any number of compounds. The results obtained for 3-component resolution are consistent with the results obtained with conventional methods of curve resolution. The same restrictions with regard to overlap and relative signal heights of the compounds seem to apply to the conventional method of curve resolution and the proposed method. The method is tested on data from high-performance liquid chromatography with a diode-array detector obtained for polynuclear aromatic hydrocarbons and for proteins.