Synthesis and electrochemical performance of LiFePO<Subscript>4</Subscript>/C cathode materials from Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> for high-power lithium-ion batteries

Carbon-coated olivine-structured LiFePO₄/C composites are synthesized via an efficient and low-cost carbothermal reduction method using Fe₂O₃ as iron source at a relative low temperature (600 °C). The effects of two kinds of carbon sources, inorganic (acetylene black) and organic (sucrose), on the structures, morphologies, and lithium storage properties of LiFePO₄/C are evaluated in details. The particle size and distribution of the carbon-coated LiFePO₄ from sucrose (LiFePO₄/SUC) are more uniform than that obtained from acetylene black (LiFePO₄/AB). Moreover, the LiFePO₄/SUC nanocomposite shows superior electrochemical properties such as high discharge capacity of 156 mAh g^?1 at 0.1 C, excellent cyclic stability, and rate capability (78 mAh g^?1 at 20 C), as compared to LiFePO₄/AB. Cyclic voltammetric test discloses that the Li-ion diffusion, the reversibility of lithium extraction/insertion, and electrical conductivity are significantly improved in LiFePO₄/SUC composite. It is believed that olivine-structured LiFePO₄ decorated with carbon from organic carbon source (sucrose) using Fe₂O₃ is a promising cathode for high-power lithium-ion batteries.     

Enhanced electrochemical performance of LiFePO4/C prepared by sol–gel synthesis with dry ball-milling

LiFePO₄/C was prepared by a modified aqueous sol–gel route developed by incorporating an additional ball-milling step where the dry gel was milled with the additives of synthetic graphite and carbon black. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), transmission electron microscopy (TEM), high resolution TEM (HRTEM) and elemental analysis. Results showed that the LiFePO₄/C synthesized by suitable ball-milling process had pure, fine and homogenous LiFePO₄ particles. Results of cyclic voltammetry and charge/discharge plateaus demonstrated that the LiFePO₄/C composite synthesized by milling for 2 h had much better electrochemical kinetics. High performances were achieved with its discharge capacities of 157 mA h g^?1 at 0.1?C and 133 mA h g^?1 at 1?C between 2.5 and 4.2 V (1?C?=?170 mA g^?1). And no obvious capacity fading was observed upon cycling. The simple and convenient synthesis route is promising for large-scale production of LiFePO₄/C.     

Propylene oxide-assisted fast sol–gel synthesis of mesoporous and nano-structured LiFePO4/C cathode materials

LiFePO₄/C nanocomposites are synthesized by a propylene oxide-assisted fast sol–gel method using FeCl₃, LiNO₃, NH₄H₂PO₄, and sucrose as the starting materials. It was found that after adding propylene oxide into the solution containing the starting materials, a monolithic jelly-like FePO₄ gel containing lithium and carbon source is generated in a few minutes without controlling the pH value of the solution and a time-consuming heating process. Propylene oxide plays a key role in the fast generation of the precursor gel. The final products of LiFePO₄/C are obtained by sintering the dry precursor gel. The structures, micro-morphologies, and electrochemical properties of the LiFePO₄/C composites are investigated using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, nitrogen adsorption–desorption analysis, electrochemical impedance spectrum, and charge–discharge cycling tests. The results indicate that the LiFePO₄/C composite prepared by sintering the precursor gel at 680 °C for 5 h is about 30 nm in size with a meso-porous structure (the main pore size distribution is around 3.4 nm). It delivers 166.7 and 105.8 mAh g^?1 at 0.2 and 30 C, respectively. The discharge specific capacity is 97.8 mAh g^?1 even at 40 C. The cycling performance of the prepared LiFePO₄/C composite is stable. The excellent electrochemical performance of the LiFePO₄/C composite is attributed to the nano-sized and mesoporous structure of LiFePO₄/C and the in-situ surface coating of the carbon. It was also found that propylene oxide is crucial for the generation of mesoporous and nano-structured LiFePO₄/C.     

Electrochemical characterization of ionic liquid based gel polymer electrolyte for lithium battery application

High molecular weight polymer poly(vinylidenefluoride-co-hexafluoropropylene) (PVdF-HFP), ionic liquid 1-ethyl-3-methylimidazolium bis(fluorosulfonyl)imide (EMIMFSI), and salt lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-based free-standing and conducting ionic liquid-based gel polymer electrolytes (ILGPE) have been prepared by solution cast method. Thermal, electrical, and electrochemical properties of 80 wt% IL containing gel polymer electrolyte (GPE) are investigated by thermogravimetric (TGA), impedance spectroscopy, linear sweep voltammetry (LSV), and cyclic voltammetry (CV). The 80 wt% IL containing GPE shows good thermal stability (~?200 °C), ionic conductivity (6.42?×?10^?4 S cm^?1), lithium ion conductivity (1.40?×?10^?4 S cm^?1 at 30 °C), and wide electrochemical stability window (~?4.10 V versus Li/Li⁺ at 30 °C). Furthermore, the surface of LiFePO₄ cathode material was modified by graphene oxide, with smooth and uniform coating layer, as confirmed by scanning electron microscopy (SEM), and with element content, as confirmed by energy dispersive X-ray (EDX) spectrum. The graphene oxide-coated LiFePO₄ cathode shows improved electrochemical performance with a good charge-discharge capacity and cyclic stability up to 50 cycles at 1C rate, as compared with the without coated LiFePO₄. At 30 °C, the discharge capacity reaches a maximum value of 104.50 and 95.0 mAh g^?1 for graphene oxide-coated LiFePO₄ and without coated LiFePO₄ at 1C rate respectively. These results indicated improved electrochemical performance of pristine LiFePO₄ cathode after coating with graphene oxide.     

A piperidinium-based ionic liquid electrolyte to enhance the electrochemical properties of LiFePO<Subscript>4</Subscript> battery

A piperidinium-based ionic liquid, N-methylpiperidinium-N-acetate bis(trifluoromethylsulfonyl)imide ([MMEPip][TFSI]), was synthesized and used as an additive to the electrolyte of LiFePO₄ battery. The electrochemical performance of the electrolytes based on different contents of [MMEPip][TFSI] has been investigated. It was found that the [MMEPip][TFSI] significantly improved the high-rate performance and cyclability of the LiFePO₄ cells. In the optimized electrolyte with 3 wt% [MMEPip][TFSI], 70 % capacity can be retained with an increase in rate to 3.5 C, which was 8 % higher than that of electrolyte without [MMEPip][TFSI]. For the Li/LiFePO₄ half-cells, after 100 cycles at 0.1 C, the discharge capacity retention was 78 % in the electrolyte without ionic liquid. However, in the electrolyte with 3 wt% [MMEPip][TFSI], it displayed a high capacity retention of 91 %. The good electrochemical performances indicated that the [MMEPip][TFSI] additive would positively enhance the electrochemical performance of LiFePO₄ battery.     

Influence of surface modification by vanadium oxide and carbon on the electrochemical performance of LiFePO4/C

Surface modification with metal oxides is an efficient method to improve the performance of LiFePO₄. Carbon and V₂O₃ co-coated LiFePO₄ is synthesized by carbothermal reduction method combined with star-balling technique, and vanadium oxide is produced in situ. The structure and pattern of LiFePO₄/C modified with different amounts of vanadium oxide (0–5 mol%) were studied by X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy, and micro-Raman spectroscopy. The electrochemical performance of material electrodes was analyzed by constant current charge–discharge and electrochemical impedance spectra (EIS). Electrochemical test results show that sample B (1.0 mol%) exhibits the best electrochemical performance, whose discharge capacity is up to 160.1, 127.2, and 88.4 mAh?g^?1 at 1, 5, and 10 °C, respectively. It indicates that V₂O₃ modification efficiently improves specific capacity and rate capability. The EIS experiment demonstrates that catalytic activity and reversibility of the cathode electrode are obviously increased by the surface modification of vanadium oxide.     

Polyol technique synthesis of Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> coated on LiFePO<Subscript>4</Subscript> cathode materials for Li-ion storage

A novel approach has been made to tailor Niobium pentoxide (Nb₂O₅) as a coating material on the surface of lithium iron phosphate (LiFePO₄) via a facile polyol technique. The coating content was optimized at 1 wt%. The superficial coating demonstrated superior discharge capacity than the pristine LiFePO₄. However, increasing the coating content further would result in a capacity loss. This may be due to the electrochemical inactiveness that increases with the content of the coating material, and 1 wt% of Nb₂O₅-coated LiFePO₄ sample exhibits initial discharge capacity of 163 mAh g^?1 at a current of 0.1 C and retains a stable discharge capacity of 143 mAh g^?1 up to 400 cycles at 1 C rate with a coulombic efficiency of 98%.

Open image in new window

Graphical abstract ?

     

High-rate Li4Ti5O12/C composites as anode for lithium-ion batteries

The Li₄Ti₅O₁₂/C composites were synthesized by a simple solid-state reaction at 800 °C for 12 h by using Super P® conductive carbon black as carbon source. X-ray diffraction analysis shows that the Li₄Ti₅O₁₂ with 0, 5, 7.5, and 10 wt% carbon shows similar patterns with cubic spinel structure. Scanning electron microscope shows that Li₄Ti₅O₁₂ aggregated seriously, but the aggregation was inhibited by the addition of Super P® carbon. The results indicate that the addition of 5 wt% carbon during sintering and a further 5 wt% carbon during slurry preparation shows the best rate capability of 110 mAh/g when the cells were charge/discharged at 10 C rate. The comparison of the charge–discharge curves shows that the higher rate improvement should further decrease the particle size of LTO or improve the conductivity of LTO itself.     

Triethylbutylammonium bis(trifluoromethanesulphonyl)imide ionic liquid as an effective electrolyte additive for Li-ion batteries

Ionic liquids are promising additives for Li-ion batteries owing to its desirable physicochemical properties. Triethylbutylammonium bis(trifluoromethanesulphonyl)imide ([N₂₂₂₄][Tf₂N]) ionic liquid was synthesized and their physical and electrochemical properties were investigated. Among several quaternary ammonium ionic liquids, [N₂₂₂₄][Tf₂N] exhibited higher conductivity (1.31 mS?cm^?1), better thermal and electrochemical stabilities, and wide electrochemical window, i.e., more than 5.9 V. Standard solution was prepared by dissolving lithium bis(trifluoromethanesulphonyl)imide (LiTf₂N) in ethylene carbonates/dimethyl carbonate (1:1, by weight). The conductivity for the electrolyte containing [N₂₂₂₄][Tf₂N] and the mixed electrolyte without additives at 25 °C are 10.24 and 8.79 mS?cm^?1, respectively. LiFePO₄ half-cell containing 0.6 mol?L^?1 LiTf₂N-based organic electrolyte with [N₂₂₂₄][Tf₂N] showed relatively high initial discharge capacity and coulombic efficiency at first cycle. It is found that the mix [N₂₂₂₄][Tf₂N] electrolyte exhibits relatively high-rate capacity. The capacity retention of half-cell containing [N₂₂₂₄][Tf₂N] is 2 % more than without additive at 0.2 C. However, the rate capacity retention of the half-cell with mix [N₂₂₂₄][Tf₂N] electrolyte is above 10 % more than without additive at 0.5 C. The results showed that [N₂₂₂₄][Tf₂N] was an effective electrolyte additive in LiFePO₄ half-cell.     

Effect of carbon coating on the electrochemical performance of LiFePO<Subscript>4</Subscript>/C as cathode materials for aqueous electrolyte lithium-ion battery

Organic electrolyte is widely used for lithium-ion rechargeable batteries but might cause flammable fumes or fire due to improper use such as overcharge or short circuit. That weakness encourages the development of tools and materials which are cheap and environmental friendly for rechargeable lithium-ion batteries with aqueous electrolyte. Lithium iron phosphate (LiFePO₄) with olivine structure is a potential candidate to be used as the cathode in aqueous electrolyte lithium-ion battery. However, LiFePO₄ has a low electronic conductivity compared to other cathodes. Conductive coating of LiFePO₄ was applied to improve the conductivity using sucrose as carbon source by heating to 600 °C for 3 h on an Argon atmosphere. The carbon-coated LiFePO₄ (LiFePO₄/C) was successfully prepared with three variations of the weight percentage of carbon. From the cyclic voltammetry, the addition of carbon coatings could improve the stability of cell battery in aqueous electrolyte. The result of galvanostatic charge/discharge shows that 9 % carbon exhibits the best result with the first specific discharge capacity of 13.3 mAh g^?1 and capacity fading by 2.2 % after 100 cycles. Although carbon coating enhances the conductivity of LiFePO₄, excessive addition of carbon could degrade the capacity of LiFePO₄.     

Electrical and complex dielectric behaviour of composite polymer electrolyte based on PEO,alumina and tetrapropylammonium iodide

In this study, the electrical, dielectric and morphological analysis of composite solid polymer electrolytes containing polyethylene oxide, alumina nano-fillers and tetrapropylammonium iodide are conducted. The temperature dependence of conductivity shows activation energy of 0.23, 0.20 and 0.29 eV for electrolytes containing 0, 5 and 15 wt.% alumina, respectively, when data fitted to the Arrhenius equation. These activation energy values are in good agreement with those determined from dielectric measurements. The result confirms the fact that conductivity is activated by both the mobility and the charge carrier density. The conductivity isotherms demonstrated the existence of two peaks, at 5 and 15 wt.% Al₂O₃ composition. The highest conductivity values of 2.4 × 10^?4, 3.3 × 10^?4 and 4.2 × 10^?4 S cm^?1 are obtained for the sample with 5 wt.% Al₂O₃ at 0, 12 and 24 °C, respectively, suggesting an enhancement of conductivity compared with that of alumina free samples.     

A facile hydrothermal method to prepare LiFePO4/C submicron rod with core–shell structure

Submicron rod LiFePO₄/C has been synthesized via a facile hydrothermal process. The morphology, crystal structure, and charge–discharge performance of the prepared samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and galvanostatic charge–discharge testing. The SEM and TEM illustrate that submicron rods with a width of about 140 nm and a length of up to 400 nm have been obtained. The TEM test also indicates a “core–shell” structure with a 1.5–2 nm carbon shell on the LiFePO₄ core. Even though the separate carbon-coated procedure is not used in this method, the electrochemical behavior results are satisfied. It displays that LiFePO₄/C has highly crystalline and a desirable core–shell structure with uniform carbon film. Galvanostatic battery testing shows that LiFePO₄/C delivers 104 mAh g^?1 at 5 C rates. The highest specific capacity of 166 mAh g^?1 is achieved at 0.1 C rate, and 99.8 % of the initial specific capacitance remained after 30 cycles.     

Studies of the electrochemical properties and thermal stability of LiNi1/3Co1/3Mn1/3O2/LiFePO4 composite cathodes for lithium ion batteries

A series of LiNi_1/3Co_1/3Mn_1/3O₂/LiFePO₄ composite cathodes with the LiFePO₄ mass content ranging from 10 to 30 wt% were prepared by ball milling in order to combine the merits of layered LiNi_1/3Co_1/3Mn_1/3O₂ and olivine LiFePO₄. The structure and morphology of the samples were characterized by X-ray diffraction and scanning electron microscope. The composite cathodes exhibited improved electrochemical performance compared with pristine LiNi_1/3Co_1/3Mn_1/3O₂. Among all the composite cathodes, the one with 20 wt% of LiFePO₄ showed the best electrochemical performance in terms of discharge capacity, cycle stability, and rate capability. Electrochemical impedance spectroscopy showed that mixing of LiFePO₄ in LiNi_1/3Co_1/3Mn_1/3O₂ decreased the internal resistance of the electrode, retarded the formation of SEI film, and facilitated the charge transfer reaction. Differential scanning calorimetry showed that the composite cathode had better thermal stability than pristine LiNi_1/3Co_1/3Mn_1/3O₂.     

Highly enhanced low-temperature performances of LiFePO<Subscript>4</Subscript>/C cathode materials prepared by polyol route for lithium-ion batteries

Although LiFePO₄/C has been successfully put into practical use in lithium-ion batteries equipped on new energy vehicles, its unsatisfactory low temperature results in poor low performance of lithium-ion batteries, leading to a much smaller continue voyage course at extreme environments with low temperature for electric vehicles. In this paper, the electrochemical performance of the LiFePO₄/C prepared by polyol route was investigated at a temperature range from 25 to ?20 °C. Compared to commercial ones, as-prepared LiFePO₄/C shows a much better low-temperature performance with a reversible capacity of 30 mA h g^?1 even at 5 C under ?20 °C and a capacity retention of 91.1 % after 100 cycles at 0.1 C under 0 °C. Moreover, high-resolution transmission electron microscopy (HRTEM) revealed that this outstanding performance at low temperatures could be assigned to uniform carbon coating and the nano-sized particles with a highly crystalline structure.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanofiller on the electrical,thermal and structural properties of PEO:PPG based nanocomposite polymer electrolyte

A new series of nanocomposite polymer electrolyte (NCPE) system comprising of polyethylene oxide (PEO) and polypropylene glycol (PPG) as blended polymer host, zinc trifluoromethanesulfonate [Zn(CF₃SO₃)₂] as dopant salt and nanocrystalline alumina [Al₂O₃] as filler was prepared by solution casting technique. The present system consisting of five different compositions of 87.5 wt% (PEO:PPG)–12.5 wt% Zn(CF₃SO₃)₂ + x wt% Al₂O₃ [where x = 1, 3, 5, 7 and 9, respectively] has been thoroughly characterized by various analytical techniques such as electrical impedance spectroscopy, X-ray diffraction (XRD) studies, differential scanning calorimetry (DSC), scanning electron microscopic (SEM) analysis and linear sweep voltammetry (LSV). The maximum room temperature ionic conductivity exhibited by the NCPE was found to be 2.1 × 10^?4 S cm^?1 for 3 wt% loading of Al₂O₃ which is an order higher than that of the optimized filler-free zinc salt doped polymer electrolyte system at 298 K. The evidence of a decrease in the degree of crystallinity responsible for the enhanced conductivity was revealed by the XRD data and further confirmed by DSC and SEM results. Moreover, the electrochemical stability window of the highly conducting electrolyte matrix has been experimentally determined by linear sweep voltammetry and found to be 3.6 V which is fairly adequate for the construction of zinc primary batteries as well as zinc-based rechargeable batteries at ambient conditions.     

Compatibility study of oxide and olivine cathode materials with lithium aluminum titanium phosphate

The compatibility of the solid electrolyte Li_1.5Al_0.5Ti_1.5(PO₄)₃ (LATP) with the cathode materials LiCoO₂, LiMn₂O₄, LiCoPO₄, LiFePO₄, and LiMn_0.5Fe_0.5PO₄ was investigated in a co-sintering study. Mixtures of LATP and the different cathode materials were sintered at various temperatures and subsequently analyzed by thermal analysis, X-ray diffraction, and electron microscopy. Oxide cathode materials display a rapid decomposition reaction with the electrolyte material even at temperatures as low as 500 °C, while olivine cathode materials are much more stable. The oxide cathode materials tend to decompose to lithium-free compounds, leaving lithium to form Li₃PO₄ and other metal phosphates. In contrast, the olivine cathode materials decompose to mixed phosphates, which can, in part, still be electrochemically active. Among the olivine cathode materials, LiFePO₄ demonstrated the most promising results. No secondary phases were detected by X-ray diffraction after sintering a LATP/LiFePO₄ mixture at temperatures as high as 700 °C. Electron microscopy revealed a small secondary phase probably consisting of Li₂FeTi(PO₄)₃, which is ionically conductive and should be electrochemically active as well.     

Effect of carbon coating on electrochemical performance of LiFePO<Subscript>4</Subscript> cathode material for Li-ion battery

Pristine LiFePO₄ (LFP) and carbon-coated LiFePO₄ (LFP/C) are synthesized by sol-gel process using citric acid as a carbon precursor. LFP/C is prepared with three different stoichiometric ratios of metal ions and citric acid, namely 1:0.5, 1:1, and 1:2. Prepared LFP and LFP/C powder samples are characterized by X-ray diffractometer, field emission scanning electron microscope, transmission electron microscope, and Raman spectrophotometer. Electrochemical performances of pristine and carbon-coated LFP are investigated by charge-discharge and cyclic voltammetry technique. The results show that LFP/C (1:1) with an optimum thickness of 4.2 nm and higher graphitic carbon coating has the highest discharge capacity of 148.2 mA h g^?1 at 0.1 C rate and 113.1 mA h g^?1 at a high rate of 5 C among all four samples prepared. The sample LFP/C (1:1) shows 96% capacity retention after 300 cycles at 1 C rate. The decrease in discharge capacity (141.4and 105.9 mA h g^?1 at 0.1 and 5 C, respectively) is observed for the sample LFP/C (1:2). Whereas, pristine LFP shows the lowest discharge capacity of 111.1 mA h g^?1 at 0.1 C and capacity was decreased very fast and work only up to 147 cycles. Moreover, cyclic voltammetry has also revealed the lowest polarization of 0.19 V for LFP/C (1:1) and the highest 0.4 V for pristine LFP.     

碳热还原法制备V2O3-C双层包覆磷酸铁锂及其电化学性能

通过V₂O₅的碳热还原反应制备了具有优异倍率性能和循环稳定性的V₂O₃-C双层包覆的磷酸铁锂正极材料. 粉末X射线衍射、元素分析、高分辨投射电镜和拉曼光谱研究表明V2O3相与碳层共包覆于磷酸铁锂颗粒表面. 在V₂O₅的碳热还原反应后,碳含量明显降低,但石墨化程度未发生明显改变. 电化学测试结果表明少量V₂O₃显著改善了磷酸铁锂正极材料的倍率性能和高温循环性能,包含1%氧化钒的复合正极材料在0.2 C放电容量为167 mAh/g,5 C时放电容量为129 mAh/g,并且循环稳定性优异;在55 oC和1 C时放电容量为151 mAh/g,循环100次后无明显容量衰减.     

Enhancement of capacity at high charge/discharge rate and cyclic stability of LiFePO4/C by nickel doping

By introducing nickel chemical into the precursor sol of LiFePO₄, a series of Ni-doped LiFePO₄ composite cathode materials, denoted as LiFe_1???x Ni _x PO₄/C (x?=?0, 0.01, 0.03, 0.05 and 0.10) were prepared by a spray drying–carbothermal approach. The materials were characterized with X-ray diffraction (XRD), scanning electron microscope (SEM), and electrochemical impedance spectrum etc. It is found that the doping of nickel with appropriate amount caused a slight shift of diffraction peaks towards higher angles and enhanced the dispersion of nanoprimary particles, which could be observed from their XRD patterns and SEM images. For the sample with 3 mol% Ni doing, the charge transfer resistance reduced from 52.4?Ω of LiFePO₄ to 18.7?Ω of LiFe_0.97Ni_0.3PO₄/C, and the potential interval of the redox peaks reduced from 0.51 to 0.40 V, indicating the better reversible of Ni-doped materials. For the sample LiFe_0.97Ni_0.03PO₄/C, its initial discharge capacities at various rates are 169.2 (0.2 C), 156.2 (1.0 C), 147.9 (2.0 C), 135.5 (5.0 C), and 94.0 (10.0 C)?mAh g^?1, respectively, enhanced by 55.2 % (at 5.0 C) and 82.1 % (at 10.0 C) compared with LiFePO₄. Furthermore, after 200 cycles of charge/discharge at 0.5 C, the capacity of LiFe_0.97Ni_0.03PO₄/C only decreased 8.8 %, but over 25 % decrease was observed for LiFePO₄/C.     

Growth of FePO<Subscript>4</Subscript> nanoparticles on graphene oxide sheets for synthesis of LiFePO<Subscript>4</Subscript>/graphene

FePO₄·xH₂O/graphene oxide (FePO₄·xH₂O/GO) composites were prepared by a facile chemical precipitation method. Using the as-prepared FePO₄·xH₂O/GO and LiOH·H₂O as precursors and followed by carbothermal reduction, LiFePO₄/graphene composites were obtained. Scanning electron microscope (SEM) images indicated that the graphene had very good dispersity and uniformly attached to the LiFePO₄ particles. The conductive framework of graphene improved the electrochemical properties of the composites. The composites deliver high initial discharge capacity of 163.4 mAh g^?1 as well as outstanding rate performance.