Structure and thermal decomposition of ammonium metatungstate

The structure and morphology of ammonium metatungstate (AMT), (NH₄)₆[H₂W₁₂O₄₀]?4H₂O, and its thermal decomposition in air and nitrogen atmospheres were investigated by SEM, FTIR, XRD, and TG/DTA-MS. The cell parameters of the AMT sample were determined and refined with a full profile fit. The thermal decomposition of AMT involved several steps in inert atmosphere: (i) release of crystal water between 25 and 200 °C resulting in dehydrated AMT, (ii) formation of an amorphous phase between 200 and 380 °C, (iii) from which hexagonal WO₃ formed between 380 and 500 °C, and (iv) which then transformed into the more stable m-WO₃ between 500 and 600 °C. As a difference in air, the as-formed NH₃ ignited with an exothermic heat effect, and nitrous oxides formed as combustion products. The thermal behavior of AMT was similar to ammonium paratungstate (APT), (NH₄)₁₀[H₂W₁₂O₄₂]?4H₂O, the only main difference being the lack of dry NH₃ evolution between 170 and 240 °C in the case of AMT.     

Thermal study on electrospun polyvinylpyrrolidone/ammonium metatungstate nanofibers: optimising the annealing conditions for obtaining WO<Subscript>3</Subscript> nanofibers

This article demonstrates how important it is to find the optimal heating conditions when electrospun organic/inorganic composite fibers are annealed to get ceramic nanofibers in appropriate quality (crystal structure, composition, and morphology) and to avoid their disintegration. Polyvinylpyrrolidone [PVP, (C₆H₉NO) _n ] and ammonium metatungstate [AMT, (NH₄)₆[H₂W₁₂O₄₀]·nH₂O] nanofibers were prepared by electrospinning aqueous solutions of PVP and AMT. The as-spun fibers and their annealing were characterized by TG/DTA-MS, XRD, SEM, Raman, and FTIR measurements. The 400–600 nm thick and tens of micrometer long PVP/AMT fibers decomposed thermally in air in four steps, and pure monoclinic WO₃ nanofibers formed between 500 and 600 °C. When a too high heating rate and heating temperature (10 °C min⁻¹, 600 °C) were used, the WO₃ nanofibers completely disintegrated. At lower heating rate but too high temperature (1 °C min⁻¹, 600 °C), the fibers broke into rods. If the heating rate was adequate, but the annealing temperature was too low (1 °C min⁻¹, 500 °C), the nanofiber morphology was excellent, but the sample was less crystalline. When the optimal heating rate and temperature (1 °C min⁻¹, 550 °C) were applied, WO₃ nanofibers with excellent morphology (250 nm thick and tens of micrometer long nanofibers, which consisted of 20–80 nm particles) and crystallinity (monoclinic WO₃) were obtained. The FTIR and Raman measurements confirmed that with these heating parameters the organic matter was effectively removed from the nanofibers and monoclinic WO₃ was present in a highly crystalline and ordered form.     

Thermal decomposition of ammonium uranates precipitated from uranyl nitrate solution with ammonium hydroxide

Thermal decomposition of ammonium uranates precipitated from uranyl nitrate solutions on addition of aqueous ammonium hydroxide under various conditions has been examined by thermogravimetry (TG), differential thermal analysis (DTA), infrared spectroscopy and X-ray diffraction study. The TG curves of all precipitates show the weight-loss corresponding to the calculated value as UO₃·NH₃·H₂O. The DTA curves of the precipitates give the endotherms at about 130, 210 and 590 °C and the exotherms at 340–420 °C. As a result, it is found that ammonium uranates thermally decompose to amorphous UO₃ at about 400 °C, and transform to U₃O₈ via β-UO₃.     

无机过氧化物的研究——Ⅱ.从粉状白钨酸制备过氧钨酸钕

应用倒滴加法制备的粉状白钨酸,制备了两个新的不同组成的过氧钨酸钕:NH_4NdW_2(O_2)_5(OH)_2·4H_2O(1)和NH_4NdW_3(O_2)_3O_8·6H_2O(2)并对化合物的一些性质进行了表征。     

Synthesis of polyethylene glycol (PEG) assisted tungsten oxide (WO3) nanoparticles for L-dopa bio-sensing applications

Nanocrystalline tungsten oxides (WO_3−δ) are currently receiving a lot of attention because of their interesting electrical, magnetic, optical and mechanical properties. In this report, we present the synthesis of PEG assisted tungsten oxide (WO₃) nanoparticles by simple household microwave irradiation (2.45 GHz) method. The samples were characterized using powder X-ray diffraction (XRD), thermal analysis (TG/DTA), transmission electron microscopy (TEM), UV-visible diffusion reflectance spectroscopy (UV-VIS-DRS), cyclic voltammetry and electrochemical impedance spectroscopy. Powder XRD results revealed that both the samples prepared with and without surfactant crystallize in the orthorhombic structure corresponding to WO₃·H₂O phase. Subsequent annealing under identical conditions (600 °C/air/6 h) led to significantly different products i.e. monoclinic W₁₇O₄₇ from surfactant free sample and orthorhombic WO₃ from PEG assisted sample. Blue emission was observed through UV-VIS-DRS with blue shift and the band gap energy was estimated as 2.7 and 3.28 eV for PEG assisted as prepared (WO₃·H₂O) and annealed samples (WO₃) respectively. Electrochemical measurements have been performed on all the samples deposited on the surface of glassy carbon (GC) electrode which showed high sensitivity and good selectivity for PEG assisted sample (WO₃·H₂O) for the direct detection of l-dopa.     

Thermal stability of hexagonal tungsten trioxide in air

We studied the thermal stability of different hexagonal tungsten trioxide, h-WO₃ samples, which were prepared either by annealing hexagonal ammonium tungsten bronze, (NH₄)_0.33−xWO_3−y, or by soft chemical synthesis from Na₂WO₄. The structure and composition of the samples were studied by powder XRD, SEM-EDX, XPS and ¹H-MAS NMR. The thermal properties were investigated by simultaneous TG/DTA, on-line evolved gas analysis (TG/DAT-MS), SEM and in situ powder XRD. The preparative routes influenced the thermal properties of h-WO₃ samples, i.e. the course of water release, the exothermic collapse of the hexagonal framework and the phase transformations were all affected.     

Phase transformations of ammonium tungsten bronzes

This article discusses the formation and structure of ammonium tungsten bronzes, (NH₄) _x WO_3−y . As analytical tools, TG/DTA-MS, XRD, SEM, Raman, XPS, and ¹H-MAS NMR were used. The well-known α-hexagonal ammonium tungsten bronze (α-HATB, ICDD 42-0452) was thermally reduced and around 550 °C a hexagonal ammonium tungsten bronze formed, whose structure was similar to α-HATB, but the hexagonal channels were almost completely empty; thus, this phase was called reduced hexagonal (h-) WO₃. In contrast with earlier considerations, it was found that the oxidation state of W atoms influenced at least as much the cell parameters of α-HATB and h-WO₃, as the packing of the hexagonal channels. Between 600 and 650 °C reduced h-WO₃ transformed into another ammonium tungsten bronze, whose structure was disputed in the literature. It was found that the structure of this phase—called β-HATB, (NH₄)_0.001WO_2.79—was hexagonal.     

层状钨基氧化物复合材料的合成与电子特性

W₂O₆·H₂O /一元烷基胺复合物[(C_nH_2n+1NH₂，n=4、8、12、16)嵌入层状氧化钨W₂O₆·H₂O] 的XRD、IR、TG-DSC分析表明：烷基胺C_nH_2n+1NH₂能基于质子加合的机制嵌入W₂O₆·H₂O层间，且插层复合物之间烷基胺的插入与抽出是个可逆过程；烷基胺嵌入层间后以全反式构象双层排布，层间距d随烷基胺碳原子数的增加而线性增长，烷基链与层板的夹角为71.6°。插层复合物UV-Vis分析发现，各种复合物的禁带宽度相对半导体氧化钨的禁带宽度变宽了很多，这表明可以通过嵌入不同的物质来调节氧化钨层与层之间的电子传递能力。     

Hydrothermal synthesis and crystal structure of a 3D supramolecular compound [H3NCH2CH2NH3]3H4[H2W12O42] · 2.5H2O

A 3D supramolecular compound [NH₃CH₂CH₂NH₃]³H₄[H₂W₁₂O₄₂] · 2.5H₂O (I) was synthesized hydrothermally and characterized by elemental analyses, IR, UV, TG analyses, and X-ray single-crystal diffraction. The X-ray diffraction experiment indicates that compound I exhibits a 3D network through electrostatic interactions and hydrogen bonding interactions between protonated ethylenediamine molecules, [H₂W₁₂O₄₀]¹⁰⁻ polyanions, and water molecules.     

Non-isothermal kinetics of thermal decomposition of NH<Subscript>4</Subscript>ZrH(PO<Subscript>4</Subscript>)<Subscript>2</Subscript>·H<Subscript>2</Subscript>O

Nanocrystalline NH₄ZrH(PO₄)₂·H₂O was synthesized by solid-state reaction at low heat using ZrOCl₂·8H₂O and (NH₄)₂HPO₄ as raw materials. X-ray powder diffraction analysis showed that NH₄ZrH(PO₄)₂·H₂O was a layered compound with an interlayer distance of 1.148 nm. The thermal decomposition of NH₄ZrH(PO₄)₂·H₂O experienced four steps, which involves the dehydration of the crystal water molecule, deamination, intramolecular dehydration of the protonated phosphate groups, and the formation of orthorhombic ZrP₂O₇. In the DTA curve, the three endothermic peaks and an exothermic peak, respectively, corresponding to the first three steps' mass losses of NH₄ZrH(PO₄)₂·H₂O and crystallization of ZrP₂O₇ were observed. Based on Flynn–Wall–Ozawa equation and Kissinger equation, the average values of the activation energies associated with the NH₄ZrH(PO₄)₂·H₂O thermal decomposition and crystallization of ZrP₂O₇ were determined to be 56.720 ± 13.1, 106.55 ± 6.28, 129.25 ± 4.32, and 521.90 kJ mol⁻¹, respectively. Dehydration of the crystal water of NH₄ZrH(PO₄)₂·H₂O could be due to multi-step reaction mechanisms: deamination of NH₄ZrH(PO₄)₂ and intramolecular dehydration of the protonated phosphate groups from Zr(HPO₄)₂ are simple reaction mechanisms.     

Thermal behaviour of nickel(II) sulphate,nitrate and halide complexes containing ammine and ethylenediamine as ligands

Thermal behaviour of nickel amine complexes containing SO₄ ²⁻, NO₃ ⁻, Cl⁻ and Br⁻ as counter ions and ammonia and ethylenediamine as ligands have been investigated using simultaneous TG/DTA coupled with mass spectroscopy (TG/DTA–MS). Evolved gas analyses detected various transient intermediates during thermal decomposition. The nickel ammonium sulphate complex produces NH, N, S, O and N₂ species. The nickel ammonium nitrate complex generated fragments like N, N₂, NO, O₂, N₂O, NH₂ and NH. The halide complexes produce NH₂, NH, N₂ and H₂ species during decomposition. The ligand ethylenediamine is fragmented as N₂/C₂H₄, NH₃ and H₂. The residue hexaamminenickel(II) sulphate produces NiO with crystallite size 50 nm. Hexaammine and tris(ethylenediamine)nickel(II) nitrate produce NiO in the range 25.5 nm and 23 nm, respectively. The halide complexes produce nano sized metallic nickel (20 nm) as the residue. Among the complexes studied, the nitrate containing complexes undergo simultaneous oxidation and reduction.     

Thermal behaviour of two new salts of malonic acid: Cu(C3H2O4)·4H2O and Cu(NH4)2(C3H2O4)2

Two new salts of malonic acid have been prepared: the copper(II) malonate tetrahydrate and the copper(II)-ammonium double malonate. Their study by thermal analysis (TG and DTA) leads to the following results:Cu(C₃H₂O₄)·4H₂O: the dehydration is rather complex and it is only under careful conditions that an intermediate hydrate Cu(C₃H₂O₄)·3H₂O could be traced. At about 170°C the dehydration is not ended (the salt holds yet about 0.15H₂O) and the anhydrous salt occurs only at about 240°C. It decomposes immediately leading to residues the composition of which depends upon the surrounding atmosphere; the part played by the gas given off is discussed.Cu(NH₄)₂(C₃H₂O₄)₂: this salt melts and decomposes simultaneously at about 190°C. During the decomposition the copper nitride Cu₃N forms as intermediate compound (as well as copper metal). Concerning the final residues of the decomposition the results and the conclusions are the same as the ones of the previous case.     

Thermal behaviour of some phosphorus/chromium polyoxoanions

The thermal degradation of K₂HPCr₂O₁₀, Na₃PCr₃O₁₃ · 3H₂O, K₃PCr₄O₁₆ and (NH₄)₃PCr₄O₁₆ has been investigated by TG and DTA methods. The main decomposition process for the three firstly mentioned compounds occurs at around 400°C and is associated with the rupture of P-O-Cr bonds. The ammonium salt shows a different behaviour and decomposes explosively at 230°C. In the case of K₂HPCr₂O₁₀ a new polyoxoanion of formula K₄P₂Cr₄O₁₉ is generated as an intermediate during the thermal degradation. Detailed stoichiometries, sustained by the TG/DTA results as well as by the chemical and infrared spectroscopic analyses of the solid residues could be given. It is shown that, in all cases, CrPO₄ is one of the decomposition products.     

Thermal dehydration and decomposition of M[M(C2O4)2]·xH2O (x=3 forM=Sr(II) andx=6 forM=Hg(II))

Strontium(II) bis (oxalato) strontium(II) trihydrate, Sr[Sr(C₂O₄)₂]·3H₂O and mercury(II) bis (oxalato) mercurate(II) hexahydrate, Hg[Hg(C₂O₄)₂]·6H₂O have been synthesized and characterized by elemental analysis, reflectance and IR spectral studies. Thermal decomposition studies (TG, DTG and DTA) in air showed SrCO₃ was formed at ca. 500°C through the formation of transient intermediate of a mixture of SrCO₃ and SrC₂O₄ around 455°C. Sharp phase transition from γ-SrCO₃ to β-SrCO₃ indicated by a distinct endothermic peak at 900°C in DTA. Mercury(II) bis (oxalato) mercurate(II) hexahydrate showed an inclined slope followed by surprisingly steep slope in TG at 178°C and finally 98.66% of weight loss at 300°C. The activation energies (E ^*) of the dehydration and decomposition steps have been calculated by Freeman and Carroll and Flynn and Wall's method and compared with the values found by DSC in nitrogen. A tentative reaction mechanism for the thermal decomposition of Sr[Sr(C₂O₄)₂]·3H₂O has been proposed.     

Synthesis and thermal decomposition of potassium peroxotitanate to K2Ti2O5

Potassium peroxotitanate was synthesized by the peroxo method. During the thermal decomposition K₂Ti₂O₅ can be obtained. The isothermal conditions for decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O were determined on the base of DTA, TG and DSC results. DTA and TG curves were recorded in the temperature range 20 and 900°C at a heating rate of 10°C min^–1. The obtained intermediate compounds were characterized by means of quantitative analysis and IR spectroscopy. The mechanism of thermal decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O to K₂Ti₂O₅ was studied. The optimal conditions for obtaining K₂Ti₂O₅ were determined (770°C for 10 h).     

Neue Heteropolyanionen des M2X2W20‐Typs mit Antimon(III) als Heteroatom

New Heteropolyanions of the M₂X₂W₂₀ Structure Type with Antimony(III) as a Heteroatom The syntheses of two new heteropolyanions of the M₂X₂W₂₀ structure type are presented. They are characterized by X‐ray structure analysis and vibrational spectra. Na₆(NH₄)₄[Zn₂(H₂O)₆(WO₂)₂(SbW₉O₃₃)₂]·36H₂O (1) is monoclinic (P2₁/n) with a = 12.873(3)Å, b = 25.303(4)Å, c = 15.975(4)Å and β = 91.99(3)°. Na₁₀[Mn₂(H₂O)₆(WO₂)₂(SbW₉O₃₃)₂]·40H₂O (2) also crystallizes in the space group P2₁/n with a = 12.892(3)Å, b = 25.219(5)Å, c = 16.166(3)Å and β = 94.41(3)°. Both polyanions are isostructural to anions of this structure type containing other heteroatoms. They are built up by two β‐B‐SbW₉ fragments, which are derived from defect structures of the Keggin anion. These subÍunits are connected by two formal WO₂ groups with further stabilization by addition of two M(H₂O)₃ groups (M = Zn^II, Mn^II, Fe^III, Co^II) leading to the M₂X₂W₂₀‐type heteropolytungstates.     

Thermal Investigations of M[La(C2O4)3]⋅xH2O (M=Cr(III) and Co(III))

The complexes M[La(C₂O₄)₃]⋅xH₂O (x=10 for M=Cr(III) and x=7 forM=Co(III)) have been synthesized and their thermal stability was investigated. The complexes were characterized by elemental analysis, IR, reflectance and powder X-ray diffraction (XRD) studies. Thermal investigations using TG, DTG and DTA techniques in air of chromium(III)tris(oxalato)lanthanum(III)decahydrate, Cr[La(C₂O₄)₃]⋅10H₂O showed the complex decomposition pattern in air. The compound released all the ten molecules of water within ∼170°C, followed by decomposition to a mixture of oxides and carbides of chromium and lanthanum, i.e. CrO₂, Cr₂O₃, Cr₃O₄, Cr₃C₂, La₂O₃, La₂C₃, LaCO, LaCrO_x (2<x<3) and C at ∼1000°C through the intermediate formation of several compounds of chromium and lanthanum at ∼374, ∼430 and ∼550°C. Thecobalt(III)tris(oxalato)lanthanum(III)heptahydrate, Co[La(C₂O₄)₃]⋅7H₂O becomes anhydrous around 225°C, followed by decomposition to Co₃O₄, La₂(CO₃)₃ and C at ∼340°C and several other mixture species of cobalt and lanthanum at∼485°C. The end products were identified to be LaCoO₃, Co₃O₄, La₂O₃, La₂C₃, Co₃C, LaCO and C at ∼ 2>1000°C. DSC studies in nitrogen of both the compounds showed several distinct steps of decomposition along with ΔH and ΔSvalues. IR and powder XRD studies have identified some of the intermediate species. The tentative mechanisms for the decomposition in air are proposed. This revised version was published online in August 2006 with corrections to the Cover Date.     

Kinetics and thermodynamics of thermal decomposition of NH<Subscript>4</Subscript>NiPO<Subscript>4</Subscript>·6H<Subscript>2</Subscript>O

The single phase NH₄NiPO₄·6H₂O was synthesized by solid-state reaction at room temperature using NiSO₄·6H₂O and (NH₄)₃PO₄·3H₂O as raw materials. XRD analysis showed that NH₄NiPO₄·6H₂O was a compound with orthorhombic structure. The thermal process of NH₄NiPO₄·6H₂O experienced three steps, which involves the dehydration of the five crystal water molecules at first, and then deamination, dehydration of the one crystal water, intramolecular dehydration of the protonated phosphate groups together, at last crystallization of Ni₂P₂O₇. In the DTA curve, the two endothermic peaks and an exothermic peak, respectively, corresponding to the first two steps’ mass loss of NH₄NiPO₄·6H₂O and crystallization of Ni₂P₂O₇. Based on Flynn–Wall–Ozawa equation, and Kissinger equation, the average values of the activation energies associated with the thermal decomposition of NH₄NiPO₄·6H₂O, and crystallization of Ni₂P₂O₇ were determined to be 47.81, 90.18, and 640.09 kJ mol⁻¹, respectively. Dehydration of the five crystal water molecules of NH₄NiPO₄·6H₂O, and deamination, dehydration of the crystal water of NH₄NiPO₄·H₂O, intramolecular dehydration of the protonated phosphate group from NiHPO₄ together could be multi-step reaction mechanisms. Besides, the thermodynamic parameters (ΔH ^≠, ΔG ^≠, and ΔS ^≠) of the decomposition reaction of NH₄NiPO₄·6H₂O were determined.     

Thermal decomposition behaviour of lanthanum(III) tris-tartrato lanthanate(III) decahydrate

Lanthanum(III) tris-tartrato lanthanate(III) decahydrate, La[La(C₄H₄O₆)₃]·10H₂O has been synthesized and characterized by elemental analysis, IR, electronic spectral and X-ray powder diffraction studies. Thermal studies (TG, DTG and DTA) in air showed a complex decomposition pattern with the generation of an anhydrous species at ~170°C. The end product was found to be mainly a mixture of La₂O₃ and carbides at ~970°C through the formation of several intermediates at different temperature. The residual product in DSC study in nitrogen at 670°C is assumed to be a similar mixture generated at 500°C in TG in air. Kinetic parameters, such as, E*, ΔH, ΔS, etc. obtained from DSC are discussed. IR and X-ray powder diffraction studies identified some of the decomposition products. The tentative mechanism for the thermal decomposition in air of the compound is proposed. This revised version was published online in July 2006 with corrections to the Cover Date.     

Determination of kinetic parameters of inorganic metalporphyrins

The thermal properties of four heteropoly complexes α-K₃H₃[SiW₁₁Ni(H₂O)O₃₉]·11.5H₂O (I), α-K₃H₂[SiW₁₁Fe(H₂O)O₃₉]·9H₂O (II), α-[(C₄H₉)₄N]_3.5H_1.5[SiW₁₁Fe(H₂O)O₃₉]·4.5H₂O (III) and α-[(C₄H₉)₄N]_3.5H_2.5[SiW₁₁Cu(H₂O)O₃₉]·6H₂O (IV) were studied by means of TG, DTA and DSC. The activation energy and reaction order of the thermal decomposition reaction of these complexes have been calculated.

---

Zusammenfassung Mittels TG, DTA und DSC wurden die thermischen Eigenschaften der vier heteropolaren Komplexe α-K₃H₃[SiW₁₁Ni(H₂O)O₃₉]·11.5H₂O (I), α-K₃H₂[SiW₁₁Fe(H₂O)O₃₉]·9H₂O (II), α-[(C₄H₉)₄N]_3.5H_1,5[SiW₁₁Fe(H₂O)O₃₉]·4.5H₂O (III) und α-[(C₄H₉)₄N]_3.5H_2,5 [SiW₁₁Cu(H₂O)O₃₉]·6H₂O (IV) untersucht. Die Aktivierungsenergie und Reaktionsordnung der thermischen Zersetzungsreaktion dieser Komplexe wurde berechnet.