Macroscopic–microscopic mechanical relaxation behavior of hybrid organic–inorganic materials

The mechanical properties of transparent hybrid organic–inorganic nanocomposites made from siloxane and zirconium oxopolymers are investigated at two different length scales. The complex interface that associates the two phases is made of covalent Zr O Si bonds and hydrogen bonding. The rubbery properties studied by creep and recovery present specific behaviors in comparison with model elastomers. This is a result of the complex crosslinking units. The stress relaxation phenomenon has been studied at the molecular scale by ²H quadrupolar NMR. During stress relaxation, the anisotropy of the molecular motion decreases slowly. This study demonstrates the straightforward relationship existing between the macroscopic and microscopic relaxation phenomena. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 645–650, 2001     

Synthesis and photophysical properties of novel organic–inorganic hybrid materials covalently linked to a europium complex

A novel sol–gel derived hybrid material (classed as Eu-DBM-Si) covalently grafted with Eu(DBM-OH)₃·2H₂O (where DBM-OH = o-hydroxydibenzoylmethane) was prepared through the primary β-diketone ligand DBM-OH. All the synthesized ligands were characterized by ¹H NMR, elemental analyses and Fourier transform infrared spectra (FTIR). The resultant Eu-DBM-Si material exhibited good transparent and homogenous property. Compared to the Eu-DBM hybrid prepared by physically doped silicon dioxide with Eu(DBM-OH)₃·2H₂O, the Eu-DBM-Si hybrid presented more efficient ligand-to-Eu³⁺ energy transfer and a significant improvement in the measured emission quantum yield. Furthermore, the photophysical properties of these hybrid materials, such as the photoluminescence (PL) spectra, PL intensities, symmetry properties, lifetime decays, and Judd-Ofelt parameters were also investigated in detail.     

Novel organic–inorganic hybrid materials from renewable resources: Hydrosilylation of fatty acid derivatives

Novel hybrid organic–inorganic materials were prepared from 10‐undecenoyl triglyceride and methyl 3,4,5‐tris(10‐undecenoyloxy)benzoate via hydrosilylation. 1,4‐Bis(dimethylsilyl)benzene, tetrakis(dimethylsilyloxy)silane, and 2,4,6,8‐tetramethylcyclotetrasiloxane were used as crosslinkers. The hydrosilylation reaction was catalyzed by Karstedt's catalyst [Pt(0)–divinyltetramethyldisiloxane complex]. The networks were structurally characterized by Fourier transform infrared spectroscopy, ¹³C NMR, and ²⁹Si magic‐angle‐spinning NMR. The thermal properties of these hybrids were studied with differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical analysis. The obtained materials showed good transparency and promising properties for optical applications. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6295–6307, 2005     

Unusual inorganic phase formation in ultraviolet‐curable organic–inorganic hybrid films

Inorganic–organic hybrid materials were prepared with a cycloaliphatic epoxide adduct of linseed oil with tetraethylorthosilicate (TEOS) oligomers via a cationic UV‐curing process. The TEOS oligomers were prepared in the presence of water and ethanol with hydrochloric acid as a catalyst. The TEOS oligomers were characterized with ¹H and ²⁹Si NMR and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. Hybrid films were cured, and the dynamic mechanical and thermal properties of the hybrid films were evaluated as a function of the TEOS oligomer content. The morphology of the hybrid films was examined with atomic force microscopy, transmission electron microscopy, and small‐angle light scattering. The microscopy and dynamic mechanical data indicated that the hybrid films were heterogeneous materials with various inorganic particle sizes dispersed within the organic matrix. In addition, ²⁹Si solid‐state NMR spectroscopy was used to investigate the coupling between the silicate region and organic regions. A schematic model is proposed to address structural features of hybrid materials. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1607–1623, 2005     

Synthesis and optical properties of organic–inorganic hybrid semi‐interpenetrating polymer network gels containing polyfluorenes

Organic–inorganic hybrid semi‐interpenetrating polymer network (semi‐IPN) gels containing polyfluorenes (PFs) are synthesized by hydrosilylation reaction of joint and rod molecules in toluene, where PFs are poly(9,9‐dihexylfluorene‐2,7‐diyl) (PF6) or, poly(9,9‐dioctylfluorene‐2,7‐diyl) (PF8), joint molecules are 1,3,5,7‐tetramethylcyclotetrasiloxane (TMCTS), or 1,3,5,7,9,11,13,15‐octakis(dimethylsilyloxy)pentacyclo‐[9,5,1,1,1,1]octasilsesquioxane (POSS), and rod molecules are 1,5‐hexadiene (HD) or 1,9‐decadiene (DD). The semi‐IPN gels containing low molecular weight PF6 show higher photoluminescence efficiency (?_g) than the toluene solution of PF6L (?_s). The semi‐IPN gels composed of long rod molecule of DD and cubic joint molecule of POSS show the most effective increase in the emission intensity. The emission intensity of PF6L increases as formation of the network in the POSS‐DD semi‐IPN gel. The POSS‐DD semi‐IPN gels containing high molecular weight PF6 and PF8 also show the increase of emission intensity than those of the toluene solutions. The semi‐IPN synthesized in cyclohexane show syneresis and phase separation between network structure and PF chains. The semi‐IPN gels containing PF8 show emission peaks at 450 and 470 nm derived from β‐sheet structure of PF8. A systematic study clears correlation between emission property and network structure and/or composition of semi‐IPN gels. The semi‐IPN gels provide emissive self‐standing soft materials with high efficiency and in a narrow wavelength range emission. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 973–984     

Liquid‐crystalline organic–inorganic hybrid polymers with functionalized silsesquioxanes

Liquid‐crystalline (LC) hybrid polymers with functionalized silsesquioxanes with various proportions of LC monomer were synthesized by the reaction of polyhedral oligomeric silsesquioxane (POSS) macromonomer with methacrylate monomer having an LC moiety under common free‐radical conditions. The obtained LC hybrid polymers were soluble in common solvents such as tetrahydrofuran, toluene, and chloroform, and their structures were characterized with Fourier transform infrared, ¹H NMR, and ²⁹Si NMR. The thermal stability of the hybrid polymers was increased with an increasing ratio of POSS moieties as the inorganic part. Because of the steric hindrance caused by the bulkiness of the POSS macromonomer, the number‐average molecular weight of the hybrid polymers gradually decreased as the molar percentage of POSS in the feed increased. Their liquid crystallinities were very dependent on the POSS segments of the hybrid polymers behaving as hard, compact components. The hybrid polymer with 90 mol % LC moiety (Cube‐LC90) showed liquid crystallinity, larger glass‐transition temperatures, and better stability with respect to the LC homopolymer. The results of differential scanning calorimetry and optical polarizing microscopy showed that Cube‐LC90 had a smectic‐mesophase‐like fine‐grained texture. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 4035–4043, 2001     

Synthesis and characterization of organic–inorganic hybrid block copolymers containing a fully condensed ladder‐like polyphenylsilsesquioxane

A series of inorganic–organic hybrid block copolymers were synthesized via atom transfer radical polymerization using a fully condensed, ladder‐like structured polyphenylsilsesquioxane end‐functionalized macroinitiator. The inorganic portion, ladder‐like polyphenylsilsesquioxane, was synthesized in a one‐batch, base‐catalyzed system, whereas organic hard and soft monomers, styrene, and n‐butyl acrylate, were polymerized and copolymerized on the ends of the linear, inorganic backbone. Synthesized hybrid diblock, triblock, and random copolymers were characterized by ¹H NMR, ²⁹Si NMR, gel permeation chromatography, static light scattering, Fourier transform infrared spectroscopy, thermogravimetric analysis, and differential scanning calorimetry. Hybrid block copolymers were well‐defined with low polydispersity (<1.4) and exhibited enhanced thermal properties in the form of increased glass transition and degradation onset temperatures over their organic analogues.© 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Characterization of proton‐conducting organic–inorganic polymeric materials by ASAXS

The distribution of ZrO₂ and phosphotungstic acid (PTA) in a matrix of sulfonated polyether ketone was investigated by anomalous small‐angle X‐ray scattering (ASAXS). Scattering curves were obtained using X‐ray energies near the Zr and W absorption edges, allowing the independent analysis of the distribution of ZrO₂ and PTA in the sample. The interaction between both inorganic components improved their dispersion considerably when compared with films containing just one of the additives. The synergism was correlated to previous investigations concerning proton conductivity and permeability of the membranes developed for direct methanol fuel cell. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2981–2992, 2005     

Isostructural organic–inorganic hybrid compounds: triethylcholine tribromidocadmate and triethylcholine tribromidomercurate

In order to search for new anionic architectures and develop useful organic–inorganic hybrid materials in halometallate systems, two new crystalline organic–inorganic hybrid compounds have been prepared, i.e. catena‐poly[triethyl(2‐hydroxyethyl)azanium [[bromidocadmate(II)]‐di‐μ‐bromido]], {(C₈H₂₀NO)[CdBr₃]}_n, (1), and catena‐poly[triethyl(2‐hydroxyethyl)azanium [[bromidomercurate(II)]‐di‐μ‐bromido]], {(C₈H₂₀NO)[HgBr₃]}_n, (2), and the structures determined by X‐ray diffraction analysis. The compounds are isostructural, crystallizing in the space group P2₁/n. The metal centres are five‐coordinated by bromide anions, giving a slightly distorted trigonal–bipyramidal geometry. The crystal structures consist of one‐dimensional edge‐sharing chains of MBr₅ trigonal bipyramids, between which triethylcholine counter‐cations are intercalated. O—H...Br hydrogen‐bonding interactions are present between the cations and anions.     

Photopolymerization of hydroxyethylmethacrylate in the formation of organic–inorganic hybrid sol–gel matrices

Hydroxyethylmethacrylate (HEMA) monomer in different contents was used in the preparation of transparent organic-inorganic hybrid sol-gel matrices. The matrices were studied by analytical techniques before and after irradiation. An increase in the homogeneity of the composite material after the irradiation of HEMA, and a chemical linkage of the monomer with the surface has been observed. Photopolymerization processes were studied by differential scanning calorimetry (DSC). Details of the irradiation times, polymerization rates, and DSC related parameters of HEMA in the sol-gel matrices are reported. © 1996 John Wiley & Sons, Inc.     

Synthesis,crystal structure solution and characterization of two organic–inorganic hybrid layered materials based on metal sulfates and 1,4‐phenylenediamine

Two organic–inorganic hybrid layered materials, namely poly[(μ‐1,4‐diaminobenzene‐κ²N:N′)[μ₃‐sulfato(VI)‐κ⁴O:O′:O′′,O′′′]manganese], [Mn(SO₄)(C₆H₈N₂)]_n, 1 , and poly[(μ‐1,4‐diaminobenzene‐κ²N:N′)[μ₃‐sulfato(VI)‐κ⁴O:O′:O′′,O′′′]copper], [Cu(SO₄)(C₆H₈N₂)]_n, 2 , have been synthesized using 1,4‐phenylenediamine (PPD) as an organic template and component (linker). Both materials form three‐dimensional frameworks. The crystal structures were determined using data from powder X‐ray diffraction measurements. The purity and morphology of the compounds were studied by elemental analyses and SEM investigations, and their thermal stabilities were determined by thermogravimetric and nonambient powder X‐ray diffraction measurements, which indicated that 1 is stable up to 537 K and 2 is stable up to 437 K.     

Synthesis,characterization, and permeability evaluation of hybrid organic–inorganic films

The preparation and characterization of hybrid organic–inorganic films based on poly(dimethylsiloxane), PDMS, crosslinked with nanoclusters obtained from pentaerythrithol triacrylate (PETA) and 2‐aminoethyl‐3‐aminopropyltrimethoxysilane (AS), are reported. The introduction of silica nanoclusters, obtained from tetraethoxysilane as an additional crosslinker, improved the mechanical stability of the films and also produced a noticeable decrease in the solvent sorption and in the distance between the nodes of the polymeric networks. The performance of these films as membranes for gas separation processes was similar to those reported for commercial PDMS, although they presented polar organic PETA/AS crosslinker nuclei. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4281–4292, 2004     

Acrylic polymer/silica organic–inorganic hybrid emulsions for coating materials: Role of the silane coupling agent

Acrylic polymer/silica organic–inorganic hybrid emulsions were synthesized by a simple method, that is, a conventional emulsion polymerization and subsequent sol–gel process, to provide water‐based coating materials. The acrylic polymer emulsions contained a silane coupling agent monomer, such as methacryloxypropyltriethoxysilane, to form highly solvent‐resistant hybrid films. On the other hand, the hybrid films from the surface‐modified polymer emulsions, in which the silane coupling agent was located only on the surface of the polymer particles and the particle core was not crosslinked, did not exhibit high solvent resistance. A honeycomblike array structure, which was derived from the polymer particles (diameter ≈ 50 nm) and the silica domain, on the hybrid film surfaces was observed by atomic force microscopy. The crosslinked core part and silane coupling agent containing the shell part of the polymer particles played important roles in attaining high solvent resistance. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4736–4742, 2006     

An organic–inorganic hybrid compound containing imidazolium cations and a one‐dimensional lithium hexacyanidocobaltate‐based anionic framework

An organic–inorganic hybrid compound, catena‐poly[bis(3H‐imidazol‐1‐ium) [[tetracyanido‐κ⁴C‐cobalt(III)]‐μ‐cyanido‐κ²C:N‐[diaqualithium(I)]‐μ‐cyanido‐κ²N:C]], {(C₃H₅N₂)₂[CoLi(CN)₆(H₂O)₂]}_n, was synthesized by the reaction of Li₃[Co(CN)₆] with imidazolium chloride in aqueous solution. The compound crystallizes in the monoclinic space group C2/c (data collected at 273 K). In the crystal structure, neighbouring [Co(CN)₆]³⁻ anionic units are linked by Li⁺ cations through the cyanide groups in a trans mode, forming a one‐dimensional zigzag chain structure extending along the c axis. A three‐dimensional supramolecular network is formed through hydrogen‐bonding interactions and is further stabilized by weak CN...π interactions between the cyanide groups and the imidazolium cations.     

Flame‐retardant epoxy resins: An approach from organic–inorganic hybrid nanocomposites

Phosphorus‐containing epoxy‐based epoxy–silica hybrid materials with a nanostructure were obtained from bis(3‐glycidyloxy)phenylphosphine oxide, diaminodiphenylmethane, and tetraethoxysilane in the presence of the catalyst p‐toluenesulfonic acid via an in situ sol–gel process. The silica formed on a nanometer scale in the epoxy resin was characterized with Fourier transform infrared, NMR, and scanning electron microscopy. The glass‐transition temperatures of the hybrid epoxy resins increased with the silica content. The nanometer‐scale silica showed an enhancement effect of improving the flame‐retardant properties of the epoxy resins. The phosphorus–silica synergistic effect on the limited oxygen index (LOI) enhancement was also observed with a high LOI value of 44.5. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 986–996, 2001     

Preparation of novel organic‐inorganic nanoporous membranes

In this study, the water permeability, the rejection property of sucrose and glucose, the fouling property of humic acid as the foulant for a novel porous fluorinated polyimide membrane made by combining the ion irradiation and plasma treatment have been reported. First, an asymmetric polyimide membrane with a defect‐free and thin skin layer was prepared, then ions on the skin layer were irradiated and the ion‐irradiated layer was treated by plasma to form nanopores in the layer. The asymmetric polyimide membranes with a defect‐free skin layer were irradiated with 50 keV He⁺ at 1 × 10¹⁵ ions/cm², and the irradiated polyimide surfaces were treated by Ar glow discharge. The porous polyimide membrane showed a high water flux and excellent rejection properties and fouling resistance when compared with NTR‐7250, which is commercially available. These findings indicated that the pore size formed on the porous polyimide membrane was effectively controlled by the plasma treatment time and the skin layer thickness. Copyright © 2005 John Wiley & Sons, Ltd.     

Development of new high transparent hybrid organic–inorganic monoliths with surface engraved diffraction pattern

Flexible hybrid xerogels bringing together high optical transparency up to 96%, low shrinkage down to 5.5%, very smooth surface (average roughness of about 0.3 nm) and thermal stability up to 200 °C were achieved as a result of the optimization of sol‐gel preparative method and a new combination of sol‐gel precursors. Two types of hybrid materials (hereafter referred, respectively, as urea‐silicate and amino‐alcohol‐silicate gels) were synthesized in this work. The shrinkage and the transparency of these materials have been drastically improved by using two different derived siloxanes (3‐isocyanate propyltriethoxysilane and 3‐glycidoxypropyltrimethoxysilane) and two amine‐terminated polyether precursors with different molecular weights. A drying process was implemented to minimize yellowing of prepared samples. Under these conditions, we were able to efficiently reproduce a well‐defined imprinted pattern at materials surface by using an original casting mould. The study of the diffraction characteristics of the obtained grating revealed a good reproducibility of the imprinted grating that shows to be comparable with the original mould. The developed methodology opens the possibility to produce diffraction lenses with a wide range of forms by a simple method based on sol‐gel process. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Preparation,characterization, and properties of novolac‐type phenolic/SiO2 hybrid organic–inorganic nanocomposite materials by sol–gel method

This article describes the preparation of novolac‐type phenolic resin/silica hybrid organic–inorganic nanocomposite, with a sol–gel process. The coupling agent was used to improve the interface between the organic and inorganic phases. The effect of the structure of the nanocomposite on its physical and chemical properties is discussed. The coupling agent reacts with the resin to form covalent bonds. The structure of the modified hybrid nanocomposites was identified with a Fourier transform infrared spectroscope. The silica network was characterized by nuclear magnetic resonance imaging (²⁹Si NMR). Results revealed that Q₄ (tetrasubstituted) and T₃ (trisubstituted) are the dominant microstructures. The size of the silica in the phenolic resin was characterized with a scanning electron microscope. The size of the particles of inorganic silica in the modified system was less than 100 nm. The nanocomposite exhibited good transparency. Moreover, the thermal and mechanical properties exhibited significant improvement. The modified hybrid composite exhibited favorable thermal properties. The temperature at which a weight loss of 5% occurred increased from 281 to 350 °C. The flexural strength increased by 6–30%. The limiting oxygen index of the nanocomposite reached 37, and the Underwriters Laboratory test was 94V‐0. Consequently, these materials possess excellent flame‐retardant properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 905–913, 2003     

Effect of anion of polyoxometalate based organic–inorganic hybrid material on intumescent flame retardant polypropylene

In this work, 12‐tungestocobaltic acid based organic–inorganic hybrid material, [Bmim]₆CoW₁₂O₄₀ (CoW) was synthesized and applied as a synergist in polypropylene (PP)/intumescent flame retardant (IFR) composites. The flame retardant properties were investigated by the limiting oxygen index (LOI), UL‐94 vertical burning test, thermal gravimetric analyzer (TGA), cone calorimeter and scanning electron microscopy (SEM) etc. The results showed that the PP composites with 16 wt% IFR and 1 wt% CoW achieves the UL‐94 V‐0 rating and gets a LOI value 28.0. However, only add no less than 25 wt% single IFR, can the PP composites obtain the UL‐94 V‐0 rating, which suggests that CoW has good synergistic effects on flame retardancy of PP/IFR composites. In addition, the SEM and cone calorimeter tests indicated the CoW improves the quality of char layer. The rate of char formation has been enhanced also because of the existence of CoW. It is the combination of a better char quality and a high rate of char formation promoted by CoW that results in the excellent flame retardancy of PP/IFR composites. Copyright © 2016 John Wiley & Sons, Ltd.     

Crosslinking effects on hybrid organic–inorganic proton conducting membranes based on sulfonated polystyrene and polysiloxane

New hybrid semi‐interpenetrating proton‐conducting membranes were obtained using sulfonated polystyrene (SPS) and inorganic–organic polysiloxane phases with the aim of improving the mechanical and thermal characteristics of the pristine polymer and to study the effects of crosslinking in the latter phase in several of their properties, mainly proton conductivity. Siloxane phases were prepared using poly(dimethylsiloxane) (PDMS) and PDMS with tetraethoxysilane (TEOS) or phenyltrimethoxysilane (PTMS) as crosslinking agents. To study the crosslinking effect, membranes were prepared with different TEOS:PDMS and PTMS:PDMS mole ratios. The films obtained were characterized by FTIR, ²⁹Si‐HPDEC MAS‐NMR, ¹³C‐CP‐MAS NMR, elemental and thermal analyses. Certain properties, such as water uptake (WU), ion exchange capacity (IEC) and the state of the water, were determined. The proton conductivity was measured at different temperatures (30°C and 80°C) and relative humidities (50–95%). The water content of the hybrid membranes declined significantly, compared with the SPS membranes, depending on the nature and amount of siloxane phase added. Nonetheless, the conductivity values remained relatively high (>100 mS cm^?1 at 80°C and 95% RH) when compared to Nafion®117 presumably because of the formation of well developed proton channels, which makes them potentially promising as proton exchange membranes for fuel cells. These membranes proved to be thermally stable up to 350°C. Scanning electron microscopy (SEM) and scanning electrochemical microscopy (SECM) were used to characterize the hybrid membranes microstructures; the latter provided contrast for the conductive domains. Copyright © 2015 John Wiley & Sons, Ltd.