We describe an electrochemical-based approach to create vertically aligned nanotube arrays on substrates. Initially, nanoporous anodic alumina films are used as templates to electrodeposit nanorods, and then the alumina templates are removed and nanotube arrays are electrodeposited using the nanorod arrays as templates. We have used this approach to fabricate gold nanotube arrays using nickel nanorods as templates. By anodizing the ends of the nickel nanorods before gold electrodeposition, no deposition occurs at the ends of the rods, resulting in open-ended nanotubes. In addition, we have used layered nickel-gold nanorods as templates to create gold nanostructure arrays with alternating segments of filled and empty nanotubes. This approach is versatile and may be used to electrodeposit a wide range of nanotube materials with good control over the nanotube dimensions. 相似文献
Immersion of nanoporous alumina membranes into saturated solutions of hexaphenylsilole with subsequent solvent evaporation affords aligned organic nanowires. The luminescent properties of the hexaphenylsilole nanowires can be manipulated by varying their morphologies, which were controlled by changing the channel sizes of the alumina templates. 相似文献
This communication describes a relatively new and simple method for the preparation of AgI nanowires using nanoporous alumina membrane templates which can be easily extended to prepare nanowires of many other materials. 相似文献
A novel scheme is presented for the synthesis of graded materials by electrodeposition in porous insulating templates. Lateral control of copper electrodeposition in nanoporous alumina membranes is achieved by application of a lateral potential gradient on a thin Au film evaporated on the membrane, used as the cathode. Formation of metal gradients in the membranes is shown to occur under conditions where essentially no gradient is formed on similar bare electrodes. This is attributed to the permanent resistivity of the thin Au film between the pores, which does not disappear upon Cu deposition, allowing a potential gradient to be maintained. Formation of a copper gradient in porous alumina membranes by uniform deposition followed by gradient dissolution is also demonstrated. These results establish the feasibility of controlled electrodeposition and gradient formation in nanoporous insulating templates. 相似文献
The aim of this work is to develop a physical model to describe the evolution of the apparent contact angle for four different liquids on nanotextured alumina surfaces with different pore radius. The nanoporous alumina templates were fabricated by anodization of Al foil in a 0.3 M oxalic acid solution. Scanning electron microscopy was used to characterize the morphology of the surfaces. The templates are approximately 400 nm in thickness and consist of a well-ordered hexagonal array of uniform radius pores spaced 105 nm apart with pore radii from 12 to 42 nm. The wettability of nanoporous alumina templates was investigated using contact-angle measurements. We measured the contact angles using four liquids: water, ethylene glycol, aniline, and a mixture of ethylene glycol and aniline. We developed a new theoretical model for the contact angle on nanoporous surfaces as a function of the pore radius. This model is based on energy considerations and involves liquid penetration into the nanopores driven by the capillarity (Laplace's law). Because the air is compressed inside the pores, this model also includes the effect of the line tension. This is important because the three-phase line length is greatly enhanced in our nanoporous structures. For example: for a millimeter-sized droplet, the three-phase line around the perimeter of the droplet is a few millimeters long, whereas the total three-phase line within the pores can reach several tens of meters. Using our model, the line-tension value for our nanopore samples is positive and ranges from 4 to 13 × 10(-9) N, which falls within the wide interval from 10(-11) to 10(-5) N quoted in the literature. Nanoporous surfaces may allow the effect of line tension to be visible for micro- to macrodroplets. 相似文献
Colloidal Au/Ag multilayer films were prepared by alternate assembly of Au nanoparticles with a size of 5 +/- 1.2 nm and Ag nanoparticles with a size of 10 +/- 2.4 nm by using 1,5-pentanedithiol as cross-linker. Nanoporous gold films with a ligament size of 26.7 +/- 4.6 nm were then prepared by selective dissolution of sacrificial templates of silver particles in colloidal Au/Ag multilayers. The complete dissolution of Ag particles in colloidal Au/Ag multilayers in a mixture solution of 3.0 mM HAuCl(4) and 3 M NaCl took place at room temperature without damage of the colloidal Au film. This method to prepare nanoporous gold films was further extended to the preparation of nanoporous gold nanotubes by depositing colloidal Au/Ag film on the inner wall of anodic aluminum oxides (AAO) followed by dissolution of colloidal Ag and removal of AAO templates. 相似文献
Nanochannel alumina templates are used as templates for fabrication of porous gold nanowire arrays by a direct electrodeposition method. After modification with glucose oxidase, a porous gold nanowire‐array electrode is shown to be an excellent electrochemical biosensor for the detection of glucose. The picture shows an SEM image of a nanowire array after removal of the alumina template by acid dissolution.
