气相色谱-质谱联用法测定聚氯乙烯塑料中7种增塑剂

建立了一种简单、快速、准确测定聚氯乙烯（PVC）塑料制品中邻苯二甲酸酯类增塑剂的方法。PVC塑料制品中7种邻苯二甲酸酯增塑剂可用超声辅助萃取有效地提取在氯仿溶剂中,然后用气相色谱-质谱联用法测定。方法的平均回收率在93．08％～104．1％之间,检出限（S／N＝3）在0．05～10．0mg·L^-1之间,相对标准偏差为0．5％～5．4％。     

固相萃取-气相色谱法测定北京市水样中的邻苯二甲酸酯

研究了使用毛细管柱（OV-1701）分离、FID作为检测器的气相色谱法测定水中5种邻苯二甲酸酯（PAEs）[邻苯二甲酸二乙酯（DEP）,邻苯二甲酸二丁酯（DBP）,邻苯二甲酸丁基苄基酯（BBP）,邻苯二甲酸二（2-乙基己基）酯（DEHP）,邻苯二甲酸二环己酯（DCHP）]的色谱条件。5种PAEs检出限在0．1～0．3μg／L之间,所测PAEs的质量浓度在0．5～100μg／L范围内,RSD在2．2％～3．3％之间,各物质校正曲线（质量浓度与峰面积）的相关系数在0．9970～0．9993之间。利用固相萃取技术萃取水中PAEs,回收率在82．5％～110．5％之间,RSD在1．1％～4．0％之间。北京市吴家村污水处理厂4个采样点中邻苯二甲酸酯浓度在（0．7～193．3）μg／L之间。北京市南护城河的3个采样点中邻苯二甲酸酯浓度在（0．1～241．8）μg／L之间。     

固相微萃取/高效液相色谱联用分析水样中邻苯二甲酸酯

研究了固相微萃取（SPME）／高效液相色谱（HPLC）联用测定环境中痕量邻苯二甲酸酯的分析方法,比较了5种不同类型涂层对5种邻苯二甲酸酯的萃取效果,采用3因素3水平正交实验设计对SPME的条件如萃取时间,离子强度,解吸时间等进行了优化,SPME优化的条件为：65μm聚二甲基硅烷／乙烯苯（PDMS／DVB）涂层,室温,搅拌速率1100r／min,萃取时间30min,纯乙腈解吸,解吸时间2min。HPLC的条件：C18反相色谱柱,乙腈-水（体积比60：40）梯度淋洗,流速1mL／min,紫外检测波长228nm。方法 的线性范围为0．50～80．00μg／L,检出限为0．11～2．20μg／L,相对标准偏差（n=6）为2．5％～9．6％,用于自来水、凉开水和雨水等实际水样的分析,回收率为82％～128％。     

高效液相色谱-串联质谱法同时测定烟用香精香料中16种邻苯二甲酸酯类化合物北大核心CSCD

采用液相色谱-串联质谱（LC—MS／MS）联用技术建立了烟用香精香料中16种邻苯二甲酸酯类化合物的测定方法。样品经超声萃取、离心后,用DionexACCLAIMC18色谱柱（150×3mm,3μm）分离,以水溶液一甲醇溶液为流动相,采用梯度洗脱方式,以电喷雾离子源正离子多反应监测模式进行分析检测。方法的定量限（S／N-10）为0．28～37．5ng／mL,线性范围为50～1000ng／mL,样品加标回收率在78．9％～119．3％范围,相对标准偏差（RSD）为2．5％～16．6％。方法成功应用于烟用香精香料中邻苯二甲酸酯类化合物的检测。     

超声波辅助萃取同位素稀释质谱法测定聚氯乙烯中6种邻苯二甲酸酯

采用超声波辅助萃取同位素稀释质谱法测定聚氯乙烯中6种邻苯二甲酸酯的含量。以四氢呋喃为溶剂对样品进行超声波辅助提取后,加入甲醇对聚合物进行沉淀,取上清液,经冷冻离心后进行气相色谱一质谱分析,并采用氘代邻苯二甲酸酯为内标,单点校正法定量。该方法应用于中、日、韩计量比对的样品测定中,两天进行的6次测定结果相对标准偏差为0．7％～3．0％。最终比对结果显示3个国家的数据取得很好的一致性,除DEP相对标准偏差为2．4％以外,其它5种邻苯二甲酸酯相对标准偏差为0．7％～1．2％,测定结果的相对扩展不确定度为1．8％～4．9％,证明该方法准确、可靠。     

茶叶中除虫菊酯农药残留快速测定法

采用丙酮浸泡、超声提取茶叶中的除虫菊酯,经石墨碳固相小柱净化萃取后,用气相色谱-电子捕获检测法直接测定茶叶中的除虫菊酯的含量。甲氰菊酯、氯氰菊酯、氰戊菊酯和溴氰菊酯的回收率为90．4％～110％,测定结果的RSD为3．4％～8．7％（n=5）,检出限为0．001～0．006mg／kg。     

固相微萃取气相色谱法(SPME-GC)测定水体中邻苯二甲酸酯

选用85μm PA纤维,考证了萃取温度、萃取时间、搅拌、离子强度及解析时间等影响因素,最后确立了65℃萃取温度、60min萃取时间、稳定的磁力搅拌、5min解析时间、用带电子捕获检测器的毛细管气相色谱（CGC—ECD）分离测定、外标标准曲线法定量分析水体中邻苯二甲酸酯（PAEs）的方法。该方法具有较好的精密度（RSD≤16％）和较低的检出限（DLDBP=0．003μg/L,DLDEDEHP=0．05μg/L）,水样加标回收率在70％～130％之间。用该法测定了长江水样、太湖水样、自来水及蒸馏水的PAEs含量,DBP在0．1～0．4μg/L,DEHP在0．2～1．2μg/L,DMP、DEP、DOP均未检测到。     

气相色谱法测定饼干类食品中氯丙醇类化合物

报道了饼干类食品中3-氯-1,2．丙二醇和1,3-二氯-2-丙醇的测定。采用乙醚索氏提取、甲醇萃取净化,再经N,O-双（三甲基硅烷）三氟乙酰胺（BSTFA）衍生,毛细管气相色谱法分离,FID作检测器。方法检出限为0．01mg／kg,回收率在90％～105％,相对标准偏差为2．2％～9．3％,     

固相萃取搅拌棒萃取-气相色谱分析海水中的多环芳烃

利用固相萃取搅拌棒（SBSE）萃取海水中的多环芳烃，然后用热解吸脱附-气相色谱分析。研究了萃取时间、添加NaCl浓度对萃取效率的影响。实验结果表明，SBSE方法对16种多环芳烃的萃取回收率分别在33．5％～122．4％之间；对标准样品的检出限为2．74-13．5ng／L；方法RSD为3．8％～13．1％。用此方法测定了大连海岸海水中的多环芳烃含量。     

高效液相色谱-二级管阵列检测器法测定化妆品中邻苯二甲酸酯

用甲醇将化妆品样品超声提取15min,离心、过滤,以XDB-C18分析枉分离分析,二级管阵列检测器检测,结合保留时间和光谱定性分析,采用高效液相色谱法测定化妆品中的邻苯二甲酸酯,外标法定量。邻苯二甲酸酯邻苯二甲酸丁基苄基酯（BBP）、邻苯二甲酸二丁酯（DBP）、邻苯二甲酸二（2-乙基已）酯（DEHP）在0．5-10．0mg／L浓度范围内均有良好的线性关系,相关系数r〉0．9998。BBP,DBP,DEHP在1．000,2．000mg／L添加水平的回收率为92％-105％,相对标准偏差（RSD）小于4％0=6）,检出限分别为14,12,6mg／kg。该方法适用于化妆品中BBP,DBP和DEHP含量的检测。     

Comparison of extraction techniques for the isolation of explosives and their degradation products from soil

A comparison of four extraction techniques used for the isolation of 14 explosive compounds (Method 8330-Explosives) from spiked soil samples is described. Soxhlet warm extraction (SWE), pressurized solvent extraction (PSE), microwave assisted extraction (MAE) and supercritical fluid extraction (SFE) were included. The effects of basic extraction conditions – i.e. type of extraction solvent, temperature, pressure, and extraction time – were investigated. The best extraction recovery of the monitored compounds from spiked soil was obtained using pressurized solvent extraction. Recoveries of explosives using the PSE technique were in the range from 65 to 112%. Extraction recoveries by Soxhlet warm extraction and supercritical fluid extraction reached 65–99% and 52–75%, respectively. The lowest extraction recoveries (28–65%) were obtained using microwave assisted extraction. A very low extraction recovery for tetryl was observed in all cases but the best results were achieved by pressurized solvent extraction (58%).     

Solid‐phase extraction using chloropropyl functionalized sol–gel hybrid sorbent for simultaneous determination of organophosphorus pesticides in selected fruit samples

A new sol–gel hybrid methyltrimethoxysilane‐chloropropyltriethoxysilane was prepared as sorbent for solid‐phase extraction. The extraction efficiency of the prepared sol–gel hybrid methyltrimethoxysilane‐chloropropyltriethoxysilane was assessed by using three selected organophosphorus pesticides, namely, chlorpyrifos, profenofos, and malathion. Gas chromatography–mass spectrometry was used for detection of organophosphorus pesticides. Several vital parameters were optimized to identify the best extraction conditions. Under the optimum extraction conditions, solid‐phase extraction‐methyltrimethoxysilane‐chloropropyltriethoxysilane method showed good linearity range (0.05‐1 μg/mL) with coefficient of determination more than 0.995. The limits of detection obtained were in the range of 0.01–0.07 μg/mL and limits of quantification ranging from 0.03 to 0.21 μg/mL. The limits of detection obtained for the developed method were 2.3–6.5× lower than the limits of detection of commercial octadecyl silica sorbent. Real samples analysis was carried out by applying the developed method on red apple and purple grape samples. The developed method exhibited good recoveries (88.33–120.7%) with low relative standard deviations ranging from 1.6 to 3.3% compared to commercial octadecyl silica sorbent, which showed acceptable recoveries (70.3–100.2%) and relative standard deviations (6.3–8.8%). The solid‐phase extraction‐methyltrimethoxysilane‐chloropropyltriethoxysilane method is presented as an alternative extraction method for determination of organophosphorus pesticides.     

Development of new extraction method based on liquid–liquid–liquid extraction followed by dispersive liquid–liquid microextraction for extraction of three tricyclic antidepressants in plasma samples

In the present study, a new extraction method based on a three–phase system, liquid–liquid–liquid extraction, followed by dispersive liquid–liquid microextraction has been developed and validated for the extraction and preconcentration of three commonly prescribed tricyclic antidepressant drugs – amitriptyline, imipramine, and clomipramine – in human plasma prior to their analysis by gas chromatography–flame ionization detection. The three phases were an aqueous phase (plasma), acetonitrile and n–hexane. The extraction mechanism was based on the different affinities of components of the biological sample (lipids, fatty acids, pharmaceuticals, inorganic ions, etc.) toward each of the phases. This provided high selectivity toward the analytes since most interferences were transferred into n–hexane. In this procedure, a homogeneous solution of the aqueous phase (plasma) and acetonitrile (water–soluble extraction solvent) was broken by adding sodium sulfate (as a phase separating agent) and the analytes were extracted into the fine droplets of the formed acetonitrile. Next, acetonitrile phase was mixed with 1,2–dibromoethane (as a preconcentration solvent at microliter level) and then the microextraction procedure mentioned above was performed for further enrichment of the analytes. Under the optimum extraction conditions, limits of detection and lower limits of quantification for the analytes were obtained in the ranges of 0.001–0.003 and 0.003–0.010 μg mL⁻¹, respectively. The obtained extraction recoveries were in the range of 79–98%. Intra– and inter–day precisions were < 7.5%. The validated method was successfully applied for determination of the selected drugs in human plasma samples obtained from the patients who received them.     

Pressurised hot water extraction in continuous flow mode for thermolabile compounds: extraction of polyphenols in red onions

Extraction and analysis of labile compounds in complex sample matrices, such as plants, is often a big analytical challenge. In this work, the use of a “green and clean” pressurised hot water extraction (PHWE) approach performed in continuous flow mode is explored. Experimental data for extraction and degradation kinetics of selected compounds were utilised to develop a continuous flow extraction (CFE) method targeting thermolabile polyphenols in red onions, with detection by high-performance liquid chromatography (HPLC)–diode array detection (DAD)–mass spectrometry (MS). Water containing ethanol and formic acid was used as extraction solvent. Method performance was focused on extraction yield with minimal analyte degradation. By adjusting the flow rate of the extraction solvent, degradation effects were minimised, and complete extraction could be achieved within 60 min. The CFE extraction yields of the polyphenols investigated were 80–90 % of the theoretically calculated quantitative yields and were significantly higher than the yields obtained by conventional methanol extraction and static batch extraction (70–79 and 58–67 % of the theoretical yields, respectively). The precision of the developed method was lower than 8 % expressed as relative standard deviation.

Development of microextraction techniques in combination with GC–MS/MS for the determination of mycotoxins and metabolites in human urine

Simple and highly efficient sample preparation procedures, namely, dispersive liquid–liquid microextraction and salting‐out liquid–liquid extraction for the analysis of ten Fusarium mycotoxins and metabolites in human urine were compared. Various parameters affecting extraction efficiency were carefully evaluated. Under optimal extraction conditions, salting‐out liquid–liquid extraction showed a better accuracy (84–96%) and precision (<14%) than dispersive liquid–liquid microextraction. Hence, a multibiomarker method based on salting‐out liquid–liquid extraction followed by gas chromatography with tandem mass spectrometry was proposed. Satisfactory results in terms of validation were achieved. The method resulted in low limits of detection and quantitation within the range of 0.12–4 and 0.25–8 μg/L, respectively. The method accuracy and precision were evaluated at three spiking levels (8, 25 and 100 μg/L) and the recoveries were in a range from 70 to 120% with relative standard deviations lower than 15%. Matrix effect was evaluated and matrix‐matched calibrations were used for quantitation purpose. The developed method was applied in 12 human urine samples as a pilot study before and after sample treatment with β‐glucuronidase before the analysis to quantify the mycotoxin conjugates. Total deoxynivalenol (free + conjugated) was found in 83% of samples at an average concentration in positive samples of 31.6 μg/L.     

Effect of Surfactants and Carbon Nanomaterials on the Electroflotation Extraction of the Disperse Phase of Cobalt Hydroxides

The effect of surfactants and carbon nanomaterials (CNMs) on the electroflotation extraction of the disperse phase of cobalt(II) and (III) hydroxides at pH 6 and pH 10 was studied. It is shown that at pH 6 in the absence of surfactants, the efficiency of cobalt extraction in various electrolytes is low and does not exceed 15–25%. In the surfactant–CNM–electrolyte system, the degree of extraction α increases in the chloride, nitrate, and sulfate solutions compared with the solutions containing no surfactants. The electroflotation extraction of cobalt was more efficient at pH 10: α reached 80–96% in the absence of surfactants, 70–97% in the surfactant–electrolyte system, and 60–97% in the surfactant–CNM–electrolyte system. The optimum conditions of the electroflotation extraction of cobalt hydroxides from solutions containing various inorganic electrolytes were determined. The effect of the sodium chloride content on the degree of cobalt extraction at pH 6 was studied. When the NaCl concentration increased from 0 to 10 g/L, the efficiency of cobalt extraction increased to 92%; when the flocculant was added and an additional stage of filtration was used, cobalt was extracted almost completely.     

Determination of triazole pesticide residues in edible oils using air‐assisted liquid–liquid microextraction followed by gas chromatography with flame ionization detection

In the present study, a rapid, simple, and highly efficient sample preparation method based on air‐assisted liquid–liquid microextraction followed by gas chromatography with flame ionization detection was developed for the extraction, preconcentration, and determination of five triazole pesticides (penconazole, hexaconazole, diniconazole, tebuconazole, and triticonazole) in edible oils. Initially, the oil samples were diluted with hexane and a few microliter of a less soluble organic solvent (extraction solvent) in hexane was added. To form fine and dispersed extraction solvent droplets, the mixture of oil sample solution and extraction solvent is repeatedly aspirated and dispersed with a syringe. Under the optimum extraction conditions, the method showed low limits of detection and quantification between 2.2–6.1 and 7.3–20 μg/L, respectively. Enrichment factors and extraction recoveries were in the ranges of 71–96 and 71–96%, respectively. The relative standard deviations for the extraction of 100 and 250 μg/L of each pesticide were less than 5% for intraday (n = 6) and interday (n = 3) precisions. Finally edible oil samples were successfully analyzed using the proposed method, and hexaconazole was found in grape seed oil.     

Development of deep eutectic solvent–based microwave-assisted extraction combined with temperature controlled ionic liquid–based liquid phase microextraction for extraction of aflatoxins from cheese samples

In this study, for the first time, a deep eutectic solvent-based microwave-assisted extraction was combined with ionic liquid–based temperature controlled liquid phase microextraction for the extraction of several aflatoxins from cheese samples. Briefly, the analytes are extracted from cheese sample (3 g) into a mixture of 1.5 mL choline chloride:ethylene glycol deep eutectic solvent and 3.5 mL deionized water by exposing to microwave irradiations for 60 s at 180 W. The liquid phase was taken and mixed with 55 μL 1-hexyl-3-methylimidazolium hexafluorophosphate. By cooling the solution in the refrigerator centrifuge, a turbid state was obtained and the analytes were extracted into the ionic liquid droplets. The analytes were determined by high-performance liquid chromatography equipped with fluorescence detector. Low limits of detection (9–23 ng kg^–1) and quantification (30–77 ng kg^–1), high extraction recovery (66%–83%), acceptable enrichment factor (40–50), and good precision (relative standard deviations ≤ 5.2%) were obtained using the offered approach. These results reveal the high extraction capability of the method for determination of aflatoxins in the cheese samples. In this method, there was no need for organic solvents and it can be considered as green extraction method.     

Microwave-assisted extraction versus Soxhlet extraction in the analysis of 21 organochlorine pesticides in plants

A method to determine 21 organochlorine pesticides in vegetation samples using microwave-assisted extraction (MAE) is described and compared with Soxhlet extraction. Samples were extracted with hexane–acetone (1:1, v/v) and the extracts were cleaned using solid-phase extraction with Florisil and alumine as adsorbents. Pesticides were eluted with hexane–ethyl acetate (80:20, v/v) and determined by gas chromatography and electron-capture detection. Recoveries obtained (75.5–132.7% for Soxhlet extraction and 81.5–108.4% for MAE) show that both methods are suitable for the determination of chlorinated pesticides in vegetation samples. The method using microwave energy was applied to grass samples from parks of A Coruña (N.W. Spain) and to vegetation from the contaminated industrial area of Torneiros (Pontevedra, N.W. Spain).     

超声萃取高效液相色谱法测定指画颜料中的6种防腐剂

建立指画颜料中2-甲基-4-异噻唑啉-3-酮、苯甲酸等6种防腐剂的超声萃取-高效液相色谱的测定方法。经试验确定,萃取溶剂为100%甲醇,萃取时间为10 min,萃取温度为25℃。采用Hypersil ODS柱(250 mm×4.6mm,5μm),以乙腈-水为流动相梯度洗脱,流速为1.0 mL/min,检测波长为245 nm。在0.5~20 mg/L检测范围内6种防腐剂的质量浓度与其色谱峰面积呈良好的线性关系,线性相关系数r≥0.999 2,方法检出限为1.15~1.71μg/L,测定结果的相对标准偏差为1.54%~3.18%(n=8),加标回收率为84.2%~108.0%。该方法操作简单,灵敏度高,可用于指画颜料中6种防腐剂含量的分析检测。