Electron transport properties of Co71−xFexCr7Si8B14 (x=0, 2, 3.2, 4, 6,8 and 12 at%) amorphous alloys during devitrification

The investigation addresses the electron transport properties of Co_71−xFe_xCr₇Si₈B₁₄ (x=0, 2, 3.2, 4, 6, 8 and 12 at%) amorphous alloys. The variation in electrical resistivity of as-cast amorphous materials with thermal scanning from room temperature to 1000 K was measured. The CoFe-based alloys revealed an initial decrease in temperature coefficient of resistivity (TCR), a characteristic of spin-wave phenomena in glassy metallic systems. This behaviour in the present alloys was in a sharp contrast to the Co-based amorphous materials that indicate the drop in resistivity much below room temperature. In the studied alloys, the variation in initial TCR values and the full-width at half-maxima determined from X-ray diffraction of as-quenched materials exhibited a similar trend with increasing Fe content, indicating the compositional effect of near neighbouring atoms. After the initial decrease in resistivity, all the alloys indicated a subsequent increase at T_min. The Curie temperature (T_C), which was measured from thermal variation of ac susceptibility showed non-monotonic change with Fe content. In the temperature range between T_min and T_C the relative scattering by electron-magnon and electron-phonon resulted in the non-monotonic change in Curie temperature. At crystallization onset (T_X1) all the alloys except there with X=6, showed a sharp decrease in electrical resistivity which was attributed to ordering phenomena. In contrast to this resistivity decrease, X=6 alloy exhibited a drastic increase in resistivity around T_X1 observed during amorphous to nanocrystalline transformation. Such nanocrystalline state was observed by Transmission electron microscopy.     

Synthesis and investigation of magnetic properties of substituted ferrite nanoparticles of spinel system Mn1−xZnx[Fe2−yLy]O4

Superparamagnetic nanoparticles of the spinel ferrite four-element system Mn_1−xZn_x[Fe_2−yL_y]O₄ (where L:Gd³⁺, La³⁺, Ce³⁺, Eu³⁺, Dy³⁺, Er³⁺,Yb³⁺) were synthesized by the co-precipitation method. The magnetic moments of the 10 nm diameter nanoparticles were comparable to the ones of Fe₃O₄ nanoparticles. A comparatively low T_C (∼52–72 °C) was observed for some of the compositions. The heating mechanism of the superparamagnetic particles in the AC magnetic field at radiofrequency range is discussed and especially the absence of the hysteresis loop in the M–H curve at room temperature. One possible explanation—spontaneous particle agglomeration—was experimentally verified.     

Synthesis,structure and magnetic properties of layered manganate Sr4Mn3−xCrxO10 (x=0, 0.2)

The manganates Sr₄Mn_3−xCr_xO₁₀ (x=0 and 0.2) have been synthesized by solid state reaction. Powder X-ray diffraction analysis shows orthorhombic symmetry with space group Cmca for both compounds. The magnetic susceptibility measurements show an antiferromagnetic transition at 192 and 176 K for x=0 and 0.2, respectively. The magnetic susceptibility data were estimated using a model based on spin exchange antiferromagnetic interactions in isolated (Mn⁴⁺) trimer; a paramagnetic contribution due to the chromium ions was added in the case of Cr-doped materials.     

Magnetocaloric properties of (La0.67−xGdx)Sr0.33MnO3 polycrystalline nanoparticles

In this paper, magnetic property and magnetocaloric effect (MCE) in nanoparticles perovskite manganites of the type (La_0.67−xGd_x)Sr_0.33MnO₃ (x=0.10, 0.15, 0.20) synthesized by using an amorphous molecular alloy as precursor have been reported. From the magnetic measurements as function of temperature and magnetic applied field, we have discovered that the Curie temperature (T_C) of the prepared samples is found to be strongly dependent on Gd content. The Curie temperature of samples is 358.4, 343.2, and 285.9 K for x=0.1, 0.15, and 0.2, respectively. A large magnetocaloric effect close to T_C has been observed with a maximum of magnetoentropy change in all the samples, ∣ΔS_M∣_max of 1.96 and 4.90 J/kg K at 2 and 5 T, respectively, for a substitution rate of 0.15. In addition, the maximum magnetic entropy change observed for samples with different concentration of Gd, exhibits a linear dependence with the applied high magnetic field. These results suggest that (La_0.67−x Gd_x)Sr_0.33MnO₃ (x=0.10, 0.15, 0.20) compounds could be a suitable candidate as working substance in magnetic refrigeration near room temperature.     

Medium range ordering and some magnetic properties of amorphous Fe90Zr7B3 alloy

High-resolution electron microscopy (HREM) reveals in the as-quenched Fe₉₀Zr₇B₃ alloy the existence of medium range ordered (MRO) regions 1-2 nm in size. Transmission Mössbauer spectroscopy confirms that these regions are α-Fe MRO ones. Above the Curie point of the amorphous phase (T_C=(257±2)K) they behave like non-interacting superparamagnetic particles with the magnetization decreasing linearly with the temperature. For these particles the average magnetic moment of 390μ_B and the average size of 1.7 nm, in excellent agreement with HREM observations, were estimated. The maximum of the isothermal magnetic entropy change at the maximum magnetizing field induction of 2 T occurs at the Curie temperature of the amorphous phase and equals to 1.05 Jkg⁻¹ K⁻¹. The magnetic entropy changes exhibit the linear dependence on the maximum magnetizing field induction in the range 0.5-2 T below, near and above T_C. Such correlations are attributed to superparamagnetic behavior of α-Fe MRO regions.     

Oxygen vacancy doping effect on the electrical and magnetic behavior of Ba5−xLaxNb4−xTixO15

We report electric and magnetic properties of oxygen deficient Ba_5−xLa_xNb_4−xTi_xO_15−δ phases, which have been prepared by solid-state reaction method followed by a controlled reduction process under hydrogen atmosphere. The extra electrons added by the formation of the oxygen vacancies (δ) introduce localized spins and the magnetic susceptibility can be described by a temperature-independent contribution and a Curie-Weiss term associated to the Ti³⁺ ion formation. Besides, the experimental resistivity (ρ) data of these four reduced compounds are well described in a wide temperature range with the equation , which suggests the presence of small polarons in the system. Although, all samples present electrical insulating behavior, the electrical resistivity decreases four orders of magnitude for intermediate x values. We interpreted this fact as a consequence of the mix between the localized bands of the Nb and Ti ions, which favors the promotion of carriers due to reduction of the band gap.     

Influence of quenching rate on the structural, soft magnetic and magnetoimpedance properties of melt-spun Co69Fe7Si14B10 alloy

Melt-spun ribbons of Co₆₉Fe₇Si₁₄B₁₀ alloy have been prepared at different wheel speeds viz. 47, 34 and 17 m/s and investigated for structural and magnetic properties. Degree of amorphicity in the as-spun ribbons is found to increase with wheel speed. Amorphous phase crystallizes in two stages producing Co₂Si, Co₂B and CoSi phases on annealing. Increase in wheel speed improves soft magnetic and magnetoimpedance properties due to decrease in perpendicular anisotropy which is associated with stripe domain formation. On annealing soft magnetic properties and magnetoimpedance deteriorate due to the formation of crystalline phases.     

The synthesis and the magnetic properties of Gd-doped FexCo1−x/CoyFe3−yO4 micro-octahedrons composites

Gd³⁺-substituted micro-octahedron composites (Fe_xCo_1−x/Co_yGd_zFe_3−y−zO₄) in which the Fe-Co alloy has either a bcc or fcc structure and the oxide is a spinel phase were fabricated by the hydrothermal method. The X-ray diffraction (XRD) patterns indicate that the as-synthesized Gd³⁺-substituted micro-octahedron composites are well crystallized. Scanning electron microscopy (SEM) images show that the final product consists of larger numbers of micro-octahedrons with the size ranging from 1.3 to 5 μm, and the size of products are increased with increasing the concentration of KOH. The effect of the Co²⁺/Fe²⁺ ratio (0?Co²⁺/Fe²⁺?1) and substitution Fe³⁺ ions by Gd³⁺ ions on structure, magnetic properties of the micro-octahedrons composites were investigated, and a possible growth mechanism is suggested to explain the formation of micro-octahedrons composites. The magnetic properties of the structure show the maximal saturation magnetization (107 emu/g) and the maximal coercivity (1192 Oe) detected by a vibrating sample magnetometer.     

High Bs nanocrystalline Fe84−x−yCuxNbySi4B12 alloys (x=0.0-1.4, y=0.0-2.5)

In this study, Cu and Nb content dependences of magnetic properties for annealed Fe_84−x−yCu_xNb_ySi₄B₁₂ alloy ribbons fabricated by melt spinning were investigated. In Fe_83−xCu_xNb₁Si₄B₁₂ alloy systems, the coercivity H_c markedly decreases with increasing x and exhibits a minimum at around x=1.0-1.2, while the saturation magnetic flux density B_s shows a slight variation. In Fe_83−yCu₁Nb_ySi₄B₁₂ alloy systems, H_c markedly decreases at around y=0.5, while B_s shows a monotonic decrease. Fe₈₂Cu₁Nb₁Si₄B₁₂ nanocrystalline alloy ribbons exhibit a high B_s of 1.78 T and a low H_c of 3.2 A/m. The core losses of the present alloys at 1.0 T at 400 Hz, P_10/400, and at 1.0 T at 1 kHz, P_10/1k, are 1.3 and 4.4 W/kg, respectively.     

Synthesis and structure refinement of layered perovskites Ba5−xLaxNb4−xTixO15 (x=0, 1, 2, 3 and 4) solid solutions

Ba_5−xLa_xNb_4−xTi_xO₁₅ solid solutions were prepared by solid state reaction method. Structural analysis for the stoichiometric phases was performed for x=0, 1, 2 and 3 by Rietveld analysis of neutron powder diffraction data. The x=0, 1 and 2 members could be refined in the space group P-3m1 (stacking sequence chhcc, polytypoid 5 H). There is a decrease in cell volume as x increases. La³⁺ occupies preferentially the A2 site (Wyckoff site 2d) and Ti⁴⁺ the B2 site (Wyckoff site 2c). As x increases there is an increase of the global instability index (GII) (which is a measure of the extent to which the BVS rule is violated over the whole structure) indicating the presence of intrinsic strains large enough to cause instability at room temperature. This strain is responsible for a structural change for the member with x=3, which could be refined in the space group P-3c1 (stacking sequence (chhcc)₂, polytypoid 2×5H=10H). This change in space group is associated with a cooperative rotation of (Nb/Ti)O₆ octahedra around the c-axis, necessary to accommodate the smaller La³⁺ ion in the cuboctahedral cavity.     

Structure,magnetic properties and magnetostriction of laves compounds Nd1−xPrx(Fe0.35Co0.55B0.1)2

The C15 Laves phases with composition Nd_1−xPr_x(Fe_0.35Co_0.55B_0.1)₂ (0?x?1) have been synthesized by arc melting and subsequent annealing. The Curie temperature T_c and the saturation magnetizations M_s at 5 and 295 K decrease with increasing Pr content. The linear anisotropic magnetostriction λ_a=λ_∥−λ_⊥ at room temperature for Nd_1−xPr_x(Fe_0.35Co_0.55B_0.1)₂ alloys with 0?x?0.4 initially reaches a negative minimum, then increases and changes its sign with increasing magnetic field H, and the λ_a for the alloys with x?0.6 is positive and increases as magnetic field H increases.     

Effect of Co ions on the microstructure and magnetic properties of nanocrystalline CoxFe3−xO4 films

Co_xFe_3−xO₄ nanocrystalline films (x=0.2-0.8$x=0.2-0.8$) on SiO₂ substrates were prepared by a sol–gel method. The microstructural and magnetic properties of samples were measured by an X-ray diffractometer (XRD) and a vibrating sample magnetometer (VSM), respectively. Atomic force microscopy (AFM) was used to investigate the surface image of the sample. The measurement results of XRD at room temperature show that the pure spinel structure of the film could be obtained at x=0.8$x=0.8$. The magnetic measurements reveal the magnetic properties of the samples depend strongly on Co²⁺ ions content, and the optimal parameters of the saturation magnetization and coercivity in Co_xFe_3−xO₄films are obtained at x=0.8$x=0.8$. Here the coercivity reaches 1.954 kOe. The average grain sizes of the film are less than 30 nm obtained from the microscopy images. The situ measurement at high temperatures of range from 293 to 773 K shows that the microstructures of Co_0.8Fe_2.2O₄ film have good thermal stabilization.     

Magnetic and magneto-optical studies on Zn1−xCrxTe (x=0.05) films grown on glass substrate

Zn_1−xCr_xTe (x=0.05) films were prepared by thermal evaporation onto glass substrates. X-ray diffraction (XRD) was used to determine the crystalline quality of the ZnTe:Cr film. Magnetic force microscopy (MFM) investigation has shown a non-uniform distribution of magnetic domains with an average size of 4 nm at room temperature. SQUID measurements have further shown that the non-uniform distribution of domains does not affect the room temperature ferromagnetism of this material. Electron spin resonance spectroscopy (ESR) was done to determine the Cr valence state in the ZnTe lattice. Magnetic circular dichroism (MCD) analysis was used to confirm the ZnCrTe phase contributing to the ferromagnetic behavior.     

Curie temperatures and crystallization behavior of amorphous Fe81−xNixZr7B12 (x=10, 20, 30, 40, 50, 60) alloys

Curie temperature, crystal structure and crystallization behavior of amorphous alloys with the stoichiometry Fe_81−xNi_xZr₇B₁₂ (x=10–60) have been studied by X-ray diffractometry (XRD), differential scanning calorimetry (DSC) and AC-magnetization (TMAG) measurements as functions of temperature. The thermal stability of long-range magnetic order, T_C vs. Ni content in as-quenched amorphous alloys exhibits maximum at 352 °C for x=40. The primary crystallization has been detected during annealing at the first crystallization stage of all ribbons investigated.     

Effect of boron concentration on the magnetic properties of (FeCoNi) 100−xBx (x=15 and 20 wt%) nanowire arrays

The Fe_14.5Co_16.5Ni₅₅B₁₅ and the Fe₁₃Co_15.5Ni_51.5B₂₀ ferromagnetic nanowires were deposited using the electrochemical deposition method. The structure of these nanowires was investigated using X-ray diffraction. Squid magnetometer was used to investigate the magnetic behavior. The hysteresis loops of 50 μm long nanowire arrays were studied as a function of boron concentration, nanowire diameter and field orientation. The competition between shape anisotropy and magnetostatic interactions played a vital role in determining the magnetic field necessary to saturate an array. The decrease in coercive field (H_c) and the squareness (SQ) of the hysteresis loop from 100 to 200 nm wire diameter for both types of compositions suggests the formation of multidomains in the nanowire.     

Magnetic properties of compounds in the system CaBaCo4−x−yZnxAlyO7 (x=0,1,2, y=0,1)

The magnetic properties of four compounds in the series CaBaCo_4−x−yZn_xAl_yO₇ (x=0,1,2, y=0,1) were investigated. Using AC-susceptibility and DC-magnetometry, magnetic transitions (T_fs) were found for all four compositions in the range 50-3 K. The data from the AC measurements proved to be frequency dependent: T_f increases with higher frequencies. An energy-loss in the magnetic coupling, indicated as contributions in the imaginary part of the magnetic susceptibility (χ″), was seen for every compound and its maximum appeared just below the maximum χ′. Modelling the data with Arrhenius-, Vogel-Fulcher-, and the power-law made it possible to relate the four compounds to spin-glass materials. The Casimir-du Pré relation was used to extract average relaxation times at T_f. The DC magnetisations clearly show differences between field-cooled and zero-field-cooled measurements. None of the compounds exhibit any metamagnetic properties up to 8 T. A new method is presented to calculate the saturation fields using DC data. Relaxation measurements on three compounds indicate that the systems relax very fast, in contrast to spin-glasses. Aging does not affect the fast relaxations. The compounds are interpreted as disordered anti-ferromagnets with spin-glass features.     

预退火时间对Fe_(80.8)B_(10)P_8Cu_(1.2)非晶合金微结构及磁性能的影响

研究了预退火时间对Fe_(80.8)B_(10)P_8Cu_(1.2)非晶合金微结构及磁性能的影响.穆斯堡尔谱研究表明:在660 K的预退火温度下,随着预退火时间的增加,Fe原子不断富集,非晶基体中的类Fe_3B化学短程有序结构向类Fe B结构转变,并且非晶基体中Fe第一近邻壳层中Cu原子的逐渐脱离以及Fe-P配位键数量的明显减少可间接表征CuP团簇的形成过程.同时,本研究通过调节预退火时间来调控非晶基体中CuP团簇和Fe团簇的数量,促进后续退火晶化过程中α-Fe纳米晶相的析出,并细化纳米晶尺寸,从而获得综合磁性能更加优异的非晶/纳米晶软磁合金.     

Soft magnetic properties and giant magneto-impedance effect of Fe73.5−xCrxSi13.5B9Nb3Au1 (x=1–5) alloys

In this paper, the effect of microstructural and surface morphological developments on the soft magnetic properties and giant magneto-impedance (GMI) effect of Fe_73.5−xCr_xSi_13.5B₉Nb₃Au₁ (x=1, 2, 3, 4, 5) alloys was investigated. It was found that the Cr addition causes slight decrease in the mean grain size of α-Fe(Si) grains. AFM results indicated a large variation of surface morphology of density and size of protrusions along the ribbon plane due to structural changes caused by thermal treatments with increasing Cr content. Ultrasoft magnetic properties such as the increase of magnetic permeability and the decrease of coercivity were observed in the samples annealed at 540 °C for 30 min. Accordingly, the GMI effect was also observed in the annealed samples.     

Microstructure and some magnetic properties of bulk amorphous (Fe0.61Co0.10Zr0.025Hf0.025Ti0.02W0.02B0.20)100−xYx (x=0, 2, 3 or 4) alloys

Microstructure, revealed by X-ray diffraction, transmission electron microscopy and Mössbauer spectroscopy, and magnetic properties such as magnetic susceptibility, its disaccommodation, core losses and approach to magnetic saturation in bulk amorphous (Fe_0.61Co_0.10Zr_0.025Hf_0.025Ti_0.02W_0.02B_0.20)_100−xY_x (x=0, 2, 3 or 4) alloys in the as-cast state and after the annealing in vacuum at 720 K for 15 min. are studied. The investigated alloys are ferromagnetic at room temperature. The average hyperfine field induction decreases with Y concentration. Due to annealing out of free volumes its value increases after the heat treatment of the samples. The magnetic susceptibility and core losses point out that the best thermal stability by the amorphous (Fe_0.61Co_0.10Zr_0.025Hf_0.025Ti_0.02W_0.02B_0.20)₉₇Y₃ alloy is exhibited. Moreover, from Mössbauer spectroscopy investigations it is shown that the mentioned above alloy is the most homogeneous. The atom packing density increases with Y concentration, which is proved by the magnetic susceptibility disaccommodation and approach to magnetic saturation studies.