Effect of composition and deposition temperature on the characteristics of Ga doped ZnO thin films

ZnO films doped with Ga (GZO) of varying composition were prepared on Corning glass substrate by radio frequency magnetron sputtering at various deposition temperatures of room temperature, 150, 250 and 400 °C, and their temperature dependent photoelectric and structural properties were correlated with Ga composition. With increasing deposition temperature, the Ga content, at which the lowest electrical resistivity and the best crystallinity were observed, decreased. Films with optimal electrical resistivity of 2-3 × 10⁻⁴ Ω cm and with good crystallinity were obtained in the substrate temperature range from 150 to 250 °C, and the corresponding C_Ga/(C_Ga + C_Zn) atomic ratio was about 0.049. GZO films grown at room temperature had coarse columnar structure and low optical transmittance, while films deposited at 400 °C yielded the highest figure of merit (FOM) due to very low optical absorption despite rather moderate electrical resistivity slightly higher than 4 × 10⁻⁴ Ω cm. The optimum Ga content at which the maximum figure of merit was obtained decreased with increasing deposition temperature.     

Dielectric behavior of spin-deposited nanocrystalline nickel-zinc ferrite thin films processed by citrate-route

Nanocrystalline nickel-zinc ferrite thin films with the general formula Ni_1−xZn_xFe₂O₄, where x=0.0, 0.2, 0.4 and 0.6 were fabricated via a chemical route known as the citrate precursor route. These films were spin-deposited on indium-tin oxide coated glass, fused quartz and amorphous Si-wafer substrates, and annealed at various temperatures up to 650 °C. The films annealed below 400 °C were found to be X-ray amorphous, while the films annealed at and above 400 °C were polycrystalline exhibiting a single-phase spinel structure. The average grain size of the films evaluated by transmission electron microscopy, is found to be in the range 4-8.5 nm. The room temperature DC resistivity of the films is in the range 10³-10⁷ Ω m. Dielectric constant and dielectric loss were measured in the frequency range 100 Hz-1 MHz. Dielectric constant of the films is found to lie between 25 and 44, while the loss factor is if the order of 10⁻². The higher values of the dielectric constant for films having higher zinc concentration are attributable to the enhanced hopping between Fe²⁺ and Fe³⁺ ions in these samples. The M-H hysteresis measurement of the nickel ferrite thin films annealed at 650 °C showed narrow hysteresis loop—a characteristic of soft ferromagnetic material.     

Microstructure and nanohardness of the diluted magnetic semiconducting Cd1−xMnxS nano-crystalline films

Cd_1−xMn_xS nano-crystalline films (0 ≤ x ≤ 0.5) were formed on glass substrates by thermal evaporation technique at room temperature (300 K). AFM studies showed that all the films were in nano-crystalline form with the grain size varying in the range between 36 and 58 nm and exhibited hexagonal structure of the host material. The lattice parameters varied linearly with composition, following Vegard's law in the entire composition range. The nanohardness and Young's modulus decreased sharply with ‘Mn’ content upto x = 0.3 and increased with high Mn content.     

Effect of substrate temperature on structure and electrical resistivity of laser-ablated IrO2 thin films

IrO₂ thin films were prepared on Si(1 0 0) substrates by laser ablation. The effect of substrate temperature (T_sub) on the structure (crystal orientation and surface morphology) and property (electrical resistivity) of the laser-ablated IrO₂ thin films was investigated. Well crystallized and single-phase IrO₂ thin films were obtained at T_sub = 573-773 K in an oxygen partial pressure of 20 Pa. The preferred orientation of the laser-ablated IrO₂ thin films changed from (2 0 0) to (1 1 0) and (1 0 1) depending on T_sub. With the increasing of T_sub, both the surface roughness and crystallite size increased. The room-temperature electrical resistivity of IrO₂ thin films decreased with increasing T_sub, showing a low value of (42 ± 6) × 10⁻⁸ Ω m at T_sub = 773 K.     

A comparative study of the physical properties of Sb2S3 thin films treated with N2 AC plasma and thermal annealing in N2

As-deposited antimony sulfide thin films prepared by chemical bath deposition were treated with nitrogen AC plasma and thermal annealing in nitrogen atmosphere. The as-deposited, plasma treated, and thermally annealed antimony sulfide thin films have been characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy, scanning electron microscopy, atomic force microscopy, UV-vis spectroscopy, and electrical measurements. The results have shown that post-deposition treatments modify the crystalline structure, the morphology, and the optoelectronic properties of Sb₂S₃ thin films. X-ray diffraction studies showed that the crystallinity of the films was improved in both cases. Atomic force microscopy studies showed that the change in the film morphology depends on the post-deposition treatment used. Optical emission spectroscopy (OES) analysis revealed the plasma etching on the surface of the film, this fact was corroborated by the energy dispersive X-ray spectroscopy analysis. The optical band gap of the films (E_g) decreased after post-deposition treatments (from 2.36 to 1.75 eV) due to the improvement in the grain sizes. The electrical resistivity of the Sb₂S₃ thin films decreased from 10⁸ to 10⁶ Ω-cm after plasma treatments.     

Characteristics of ZnO:Al thin films co-doped with hydrogen and fluorine

Fluorine and hydrogen co-doped ZnO:Al (AZO) films were prepared by radio frequency (rf) magnetron sputtering of ZnO targets containing 1 wt.% Al₂O₃ on Corning glass at substrate temperature of 150 °C with Ar/CF₄/H₂ gas mixtures, and the structural, electrical and optical properties of the as-deposited and the vacuum-annealed films were investigated. In as-deposited state, films with fairly low resistivity of 3.9-4 × 10⁻⁴ Ω cm and very low absorption coefficient below 900 cm⁻¹ when averaged in 400-800 nm could be fabricated. After vacuum-heating at 300 °C, the minimum resistivity of 2.9 × 10⁻⁴ Ω cm combined with low absorption loss in visible region, which enabled the figure of merit to uplift as high as 4 Ω⁻¹, could be obtained for vacuum-annealed film. It was shown that, unlike hydrogenated ZnO films which resulted in degradation upon heating in vacuum at moderately high temperature, films with fluorine addition could yield improved electrical properties mostly due to enhanced Hall mobility while preserving carrier concentration level. Furthermore, stability in oxidizing environment could be improved by fluorine addition, which was ascribed to the filling effect of dangling bonds at the grain boundaries. These results showed that co-doping of hydrogen and fluorine into AZO films with low Al concentration could be remarkably compatible with thin film solar cell applications.     

Room temperature photoluminescence from amorphous silicon nanoparticles in SiOx thin films

Amorphous SiO_x thin films with four different oxygen contents (x=1.15, 1.4, 1.5, and 1.7) have been prepared by thermal evaporation of SiO in vacuum and then annealed at 770 or 970 K in argon for various times ?40 min. The influence of annealing conditions and the initial film composition on photoluminescence (PL) from the annealed films has been explored. Intense room temperature PL has been observed from films with x?1.5, visible with a naked eye. It has been shown that PL spectra of most samples consists of two main bands: (i) a ‘green’ band centered at about 2.3 eV, whose position does not change with annealing conditions and (ii) an ‘orange-red’ band whose maximum moves from 2.1 to 1.7 eV with increasing annealing time and temperature and decreasing initial oxygen content. These observations have been explained assuming recombination via defect states in the SiO_x matrix for the first band and emission from amorphous Si nanoparticles for the second one.     

Transparent and conducting Zn-Sn-O thin films prepared by combinatorial approach

Zn-Sn-O (ZTO) films with continuous compositional gradient of Sn 16-89 at.% were prepared by co-sputtering of two targets of ZnO and SnO₂ in a combinatorial method. The resistivities of the ZTO films were severely dependent on oxygen content in sputtering gas and Zn/Sn ratio. Except for the films with Sn 16 at.%, all the as-prepared films were amorphous and maintaining the stable amorphous states up to the annealing temperature of 450 °C. Annealing at 650 °C resulted in crystallization for all the composition, in which ZnO, Zn₂SnO₄, ZnSnO₃, and SnO₂ peaks were appeared successively with increasing Sn content. Above Sn 54 at.%, the ZTO films were deduced to have a local structure mixed with ZnSnO₃ and SnO₂ phases which were more conductive and stable in thermal oxidation than ZnO and Zn₂SnO₄ phases. The lowest resistivity of 1.9 × 10⁻³ Ω cm was obtained for the films with Sn 89 at.% when annealed at 450 °C in a vacuum. The carrier concentrations of the amorphous ZTO films that contained Sn contents higher than 36 at.% and annealed at 450 °C in a vacuum were proportional to the Sn contents, while the Hall mobilities were insensitive to Sn contents and leveling in the range of 23-26 cm²/V s.     

Spin-deposited nanocrystalline lithium ferrite thin films: Fabrication and characterization

Thin films of lithium ferrite (with general composition Li_0.5Fe_2.5O₄) were fabricated at low temperatures (up to 650 °C) by citrate-route using spin-deposition technique. Deposited films consisted of nanometer-sized grains as evidenced by X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. XRD patterns for annealed films showed broad peaks exhibiting a spinel phase. Size of nanocrystallites is estimated to be 3-7 nm using Scherrer's equation. Average grain size ∼8.5 nm is observed from TEM images of films annealed at 650 °C. Scanning electron micrographs show the formation of spherical aggregates of around 130 nm in diameter. The AFM analysis clearly evidenced the development of nanograins even at low (∼500 °C) annealing temperatures. Significant decrease in complex dielectric permittivity (∈′ − j∈″) with frequency is observed in the low frequency (100 Hz-1 MHz) as well as in X-band microwave frequency (8-12 GHz) region. ∈′ is found to be in the range of 15.7-33.9 in low frequency region, whereas in X-band microwave frequency region, it is found to lie between 3.9 and 4.9. Similarly, ∈″ is found to be 0.16-5.9 in the low frequency region, and 0.002-0.024 in the X-band microwave frequency region. Room temperature dc resistivity of these films is estimated to lie in the range of 10⁶-10⁸ Ω cm. These results strongly suggest that citrate-route processed nanocrystalline lithium ferrite thin films are promising candidates for monolithic microwave integrated circuits (MMICs).     

Structural and optical properties of thin films porous amorphous silicon carbide formed by Ag-assisted photochemical etching

In this work, we present the formation of porous layers on hydrogenated amorphous SiC (a-SiC: H) by Ag-assisted photochemical etching using HF/K₂S₂O₈ solution under UV illumination at 254 nm wavelength. The amorphous films a-SiC: H were elaborated by d.c. magnetron sputtering using a hot pressed polycrystalline 6H-SiC target. Because of the high resistivity of the SiC layer, around 1.6 MΩ cm and in order to facilitate the chemical etching, a thin metallic film of high purity silver (Ag) has been deposited under vacuum onto the thin a-SiC: H layer. The etched surface was characterized by scanning electron microscopy, secondary ion mass spectroscopy, infrared spectroscopy and photoluminescence. The results show that the morphology of etched a-SiC: H surface evolves with etching time. For an etching time of 20 min the surface presents a hemispherical crater, indicating that the porous SiC layer is perforated. Photoluminescence characterization of etched a-SiC: H samples for 20 min shows a high and an intense blue PL, whereas it has been shown that the PL decreases for higher etching time. Finally, a dissolution mechanism of the silicon carbide in 1HF/1K₂S₂O₈ solution has been proposed.     

Chemical bath deposition of Bi2S3 films by a novel deposition system

Bismuth sulfide (Bi₂S₃) films were chemically deposited by a novel deposition system in which ammonium citrate was used as the chelating reagent. Two sulfur source thioacetamide (TA) and sodium thiosulfate (Na₂S₂O₃) were used to prepare Bi₂S₃ films. Both the as-prepared films have amorphous structure. However, annealing can improve the crystallization of the films. The composition of the films prepared by TA and Na₂S₂O₃ are all deviate from the stoichiometric ratio of Bi₂S₃. The Bi₂S₃ films are all homogeneous and well adhered to the substrate. The optical properties of the Bi₂S₃ films are studied. The electrical resistivity of the as-prepared films are all around 7 × 10³ Ω cm in dark, which decreases to around 1 × 10³ Ω cm under 100 mW/cm² tungsten-halogen illumination. After the annealing, the dark resistivity of the Bi₂S₃ film prepared by TA decreases by four magnitudes. In contrast, the dark resistivity of the Bi₂S₃ film prepared by Na₂S₂O₃ only decreases slightly.     

Magnetic,structural and electrical properties of ordered and disordered Co50Fe50 films

Co₅₀Fe₅₀ films with thickness varying from 100 to 500 Å were deposited on a glass substrate by sputtering process, respectively. Two kinds of CoFe films were studied: one was the as-deposited film, and the other the annealed film. The annealing procedure was to keep the films at 400 °C for 5 h in a vacuum of 5×10⁻⁶ mbar. From the X-ray study, we find that the as-deposited film prefers the CoFe(1 1 0) orientation. Moreover, the body-centered cubic (bcc) CoFe(1 1 0) line is split into two peaks: one corresponding to the ordered body-centered tetragonal (bct) phase, and the other, the disordered bcc phase. After annealing, the peak intensity of the ordered bct phase becomes much stronger, while that of the disordered bcc phase disappears. The annealing has also caused the ordered CoFe(2 0 0) line to appear. When the amount of the ordered bct phase in Co₅₀Fe₅₀ is increased, the saturation magnetization (M_s) and coercivity (H_c) become larger, but the electrical resistivity (ρ) decreases. From the temperature coefficient of resistance (TCR) measurement, we learn that the bct grains in the CoFe film start to grow at temperature 82 °C.     

Effect of substrate temperature on the growth of ITO thin films

Indium tin oxide (ITO) thin films were deposited onto glass substrates by rf magnetron sputtering of ITO target and the influence of substrate temperature on the properties of the films were investigated. The structural characteristics showed a dependence on the oxygen partial pressure during sputtering. Oxygen deficient films showed (4 0 0) plane texturing while oxygen-incorporated films were preferentially oriented in the [1 1 1] direction. ITO films with low resistivity of 2.05 × 10⁻³ Ω cm were deposited at relatively low substrate temperature (150 °C) which shows highest figure of merit of 2.84 × 10⁻³ square/Ω⋅     

Structure, magnetic and electrical transport properties of cosputtered Fe0.5Ge0.5 nanocomposite films

Fe_0.5Ge_0.5 nanocomposite films with different film thicknesses were fabricated using cosputtering. The films are composed of Ge, Fe and Fe₃Ge₂, and are ferromagnetic at room temperature. The saturation magnetization and magnetic interaction including dipolar interaction and exchange coupling increase with the increasing film thickness. The electrical conductance mechanism turns from metallic to semiconducting and the saturation Hall resistivity ρ_xys increases with the decreasing film thickness. At 28 nm, ρ_xys is ∼137 μΩ cm at 2 K, about 150 times larger than that of pure Fe film (0.9 μΩ cm) and four orders larger than that of bulk Fe. The ρ_xy-H curves of all the films show the same linearity character in low-field range even though the temperature-independent slope is different at different film thicknesses. At high temperatures, the skew scattering mechanism is dominant. At low temperatures, side-jump effect should be dominant at large resistivity ρ_xx regime for the thin films, and the skew scattering is dominant at small ρ_xx regime for the thick films.     

Preparation and multi-properties of insulated single-phase BiFeO3 ceramics

Six types of BiFeO₃ ceramic samples, with subtle differences in synthesis conditions, were prepared. The comparison of their phases, electrical resistivity, and porosity revealed that the use of Bi₂O₃ and Fe₂O₃ powders of <1 μm size and a rapid liquid-phase sintering process of 855 °C for 5 min at 100 °C/s is beneficial to synthesize poreless single-phase BiFeO₃ samples with high electrical resistivity of ∼5×10¹² Ω cm. Deoxygenated Bi_xFe_yO_{1.5x+1.5y−δ} (x≠y, δ≥0) impurities were identified and found to be the main cause of low electrical resistivity and high porosity in the multi-phase samples. Large saturation polarization of 16.6 μC/cm² and low leakage current density of 30 mA/m², both at a high electric field of 145 kV/cm, were measured in the optimized single-phase samples at room temperature besides a large piezoelectric d₃₃ coefficient of 27 pC/N and an obvious canted antiferromagnetic behavior.     

On tuning the orientation of grains of spray pyrolysed ZnO thin films

Effect of varying spray rate on the structure and optoelectronic properties of spray pyrolysed ZnO film is analysed. ZnO films were characterised using different techniques such as X-ray diffraction (XRD), photoluminescence, electrical resistivity measurement, and optical absorption. The XRD analysis proved that, with the increase in spray rate, orientation of the grains changed from (1 0 1) plane to (0 0 2) plane. The films exhibited luminescence in two regions—one was the ‘near band-edge’ (NBE) (∼380 nm) emission and the other one was the ‘blue-green emission’ (∼503 nm). Intensity of the blue-green emission decreased after orientation of grains shifted to (0 0 2) plane. Scanning electron microscope (SEM) analysis of the films asserts that spray rate has major role in improving the crystallographic properties of the films. Moreover resistivity of the films could be lowered to 2.4 × 10⁻² Ω cm without any doping or post-deposition annealing.     

Magnetic field dependence of asymmetry in the magnetization reversal of ultrathin Co films and Co/Pt multilayers with perpendicular anisotropy

We studied the magnetization reversal in ultrathin [Co/Pt]_n films (n=1, 2, and 4) using magneto-optical Kerr microscopy. These materials demonstrate unusual asymmetries in the activity of nucleation centers and domain wall motion. It was found that application of very high holding magnetic field prior to magnetization reversal, exceeding some critical value much larger than the apparent saturation field, suppresses the subsequent ‘asymmetric’ nucleation centers, activity. We revealed that the ‘asymmetric’ nucleation centers become active again after subsequent reversal cycles coming from a smaller holding field and studied how the asymmetry returns with the decrease of applied holding field. It was found that in low-coercivity ultrathin Co films, the asymmetry in domain wall velocity decreased sharply with the applied field increase and disappeared when the reversal field is greater than μ₀H=1.5 mT.     

Magnetic properties of CoFeP films prepared by electroless deposition

Structure and magnetization of CoFeP films prepared by the electroless deposition were systematically investigated by varying the bath composition and deposition parameters to optimize soft magnetic properties. The cobalt content in the CoFeP films varies from 40.4 to 94.9 wt% by controlling the bath composition. Increase of the metallic ratio FeSO₄·7H₂O/(CoSO₄·7H₂O+FeSO₄·7H₂O) affects the films’ microstructure, which switches from amorphous to crystalline structure. The magnetic properties of CoFeP films reveal that the coercivity (H_c) values range from 80 up to 185 A/m and the saturation magnetization (M_s) from 82 to 580 eum/g depending on the bath composition, deposition parameters and heat-treatment conditions. Increase of M_s and remanent magnetization (M_r) as well as decrease of H_c are observed for the CoFeP films with bath pH, temperature and the metallic molar ratio increasing. It is also found that the H_c is enhanced with the increase of NaH₂PO₂·H₂O concentration. CoFeP films showing good soft magnetic properties with coercivities less than 140 A/m and M_s close to 600 emu/g can be obtained in high pH bath and thereafter heat treatment. The deposit is found to be suitable as soft magnetic materials for core materials.     

Magnetic properties of CoPt–SiNx/Ag nanocomposite films

When the thickness of Ag under layer is 25 nm, the CoPt/Ag film has maximum out-of-plane squareness (S_⊥), minimum in-plane squareness (S_∥), and the largest out-of-plane coercivity (H_c⊥), they are 0.95, 0.35, and 15 kOe, respectively. Different volume percent of SiN_x ceramic materials were co-sputtered with Co₅₀Pt₅₀ films on the Ag under layer to reduce the grain size of the CoPt film. Comparing the X-ray diffraction pattern of CoPt-SiN_x/Ag films without annealing with that of the films which annealed at 600 and 700 °C, it is found that the intensities of CoPt (0 0 1) and CoPt (0 0 2) superlattice lines were reduced after annealing. As the SiN_x content is raised to 50 vol%, the particle size of CoPt is reduced to be about 9 nm.     

Structure and electrical properties of CdIn2O4 thin films prepared by DC reactive magnetron sputtering

CdIn₂O₄ thin films were prepared by direct-current (DC) reactive magnetron sputtering. The structure, surface morphology and the chemical composition of the thin films were analyzed by X-ray diffraction (XRD), atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. The electrical properties of the films prepared in different oxygen concentration and annealing treatment were determined, and the effects of the preparing conditions on the structure and electrical properties were also explored. It indicates that the CdIn₂O₄ thin films with uniform and dense surface morphology contain mainly CdIn₂O₄, In₂O₃ phases, and CdO phase is also observed. The XPS analysis confirms the films are in oxygen-deficient state. The electrical properties of these films significantly depend on the preparing conditions, the resistivity of the films with the oxygen concentration of 4.29% is 2.95 × 10⁻⁴ Ω cm and the Hall mobility is as high as 60.32 cm²/V s. Annealing treatment can improve the electrical performance of the films.