Hydrogen production via autothermal reforming of ethanol over noble metal catalysts supported on oxides

Hydrogen was produced over noble metal (Ir, Ru, Rh, Pd) catalysts supported on various oxides, including γ-Al₂O₃, CeO₂, ZrO₂ and La₂O₃, via the autothermal reforming reaction of ethanol (ATRE) and oxidative reforming reaction of ethanol (OSRE). The conversion of ethanol and selectivites for hydrogen and byproducts such as methane, ethylene and acetaldehyde were studied. It was found that lanthana alone possessed considerable activity for the ATRE reaction, which could be used as a functional support for ATRE catalysts. It was demonstrated that Ir/La₂O₃ prevented the formation of methane, and Rh/La₂O₃ encumbered the production of ethylene and acetaldehyde. ATRE reaction was carried out over La₂O₃-supported catalysts (Ir/La₂O₃) with good stability on stream, high conversion, and excellent hydrogen selectivity approaching thermodynamic limit under autothermal condition. Typically, 3.4 H₂ molecules can be extracted from a pair of ethanol and water molecules over Ir(5wt%)/La₂O₃. The results presented in this paper indicate that Ir/La₂O₃ can be used as a promising catalyst for hydrogen production via ATRE reaction from renewable ethanol.     

镍基催化剂上乙醇水蒸气重整反应的研究

考察了载体对Ni催化剂乙醇水蒸气重整制氢反应性能的影响。结果表明,Ni/CeO2催化剂具有较好的低温活性和氢气选择性。对Ni担载量和焙烧温度考察发现,400℃焙烧的15%NiCeO2催化剂具有较好的催化性能;继续升高焙烧温度引起NiO和CeO2粒子的显著增大,导致对氢气选择性的降低。较小的Ni和CeO2粒子有利于乙醇水汽重整反应的进行,而大的粒子倾向于乙醇的分解反应。 350℃时,在反应过程中分别添加CO、CO2和CH4的结果表明没有发生CO和CO2甲烷化反应,而发生了一定程度的CH4水汽重整反应。     

Ni-Fe/蒙脱土催化剂催化乙醇水蒸气重整制氢的研究

采用浸渍法制备了一系列Ni-Fe/蒙脱土(MMT)催化剂,并应用于乙醇水蒸气重整制氢反应(ESR)。采用X射线衍射(XRD)、N_2吸附脱附分析和H_2-程序升温还原(H_2-TPR)表征手段对催化剂的物理化学性质、还原性能、碳沉积等进行了研究。结果表明,Ni-Fe/MMT催化剂中,Ni、Fe高度分散在载体MMT层间及表面,而且Fe的加入降低了Ni颗粒的粒径,增强了Ni~(2+)与载体的相互作用力。以10Ni5Fe/MMT为催化剂,在反应温度为500℃、水醇比为3∶1、空速为12 h~(-1),反应进行30 h后,乙醇转化率为100%,氢气选择性仍保持72%,副产物CO和CH_4含量明显降低。这是因为催化助剂Fe的引入,一方面,提高了Ni的分散度,使得ESR低温活性较好;另一方面,减小了Ni颗粒粒径,小颗粒的Ni有利于抑制甲烷的生成,并且Fe的加入加强了甲烷重整和水煤气变换反应,提高产物中氢气的选择性。     

催化剂Ni/Y2O3上低温乙醇水蒸气重整制氢研究——氢气预还原对催化剂性能的影响

用浸渍－热分解－氢还原法(IHDHR)和浸渍－热分解法(IHD)分别制备了两种纳米尺寸的Ni/Y2O3催化剂，并应用X-光电子能谱、X-射线衍射、BET比表面测试等分析技术对两种催化剂的结构进行了表征和比较。采用固定床反应器对两种催化剂的催化性能进行实验测试。结果表明，氢气预还原与否对该纳米Ni/Y2O3催化剂的催化性能有一定的影响，经过氢气预还原的催化剂对低温乙醇水蒸气重整反应表现出较高的活性和稳定性，250?℃时，乙醇的转化率达到81.9%；320 ℃时，乙醇的转化率达到95.3%，对氢气的选择性为53.6%。对经过氢预还原的Ni/Y2O3催化剂进行了60 h的稳定性测试。     

负载Ni催化剂用于乙二醇蒸汽重整制氢催化性能研究

采用等体积浸渍法和共沉淀法制备了Ni催化剂,在固定床反应器上考察了Ni负载量、焙烧温度、反应温度等因素对乙二醇低温重整制氢反应活性和选择性的影响。应用X射线衍射、氮物理吸附、H₂程序升温还原等技术对负载型Ni催化剂进行了表征。结果表明,共沉淀法制备的Ni/CeO₂催化剂具有较小的NiO颗粒与CeO₂载体颗粒粒径,催化活性较高。添加少量氧化钴到Ni/CeO₂催化剂中可使H₂收率达72.6%,EG转化率达93.1%。在CeO₂中添加Al₂O₃能提高负载Ni催化剂的活性,乙二醇转化率达94.0%,H₂收率达67.0%;但添加SiO₂则使其活性明显变差。     

镍负载量对乙醇水蒸气重整制氢催化性能和催化剂的影响

采用稳态实验对镍负载量对Ni/MgO催化剂在乙醇水蒸气重整反应的影响进行了研究。结果表明,在101.3kPa下,镍负载量越高,催化剂的活性越高。对于催化剂的选择性,存在一个最佳镍负载量为10%Ni/MgO。按选择性从大到小排序,不同镍负载量的催化剂为：10Ni/MgO>15Ni/MgO>12.5Ni/MgO>7.5Ni/MgO≈5Ni/MgO。热分析表明,焙烧过程中不同镍负载量的催化剂镍前体与载体前体之间发生的相互作用不同。XRD和TPR 表征结果显示,催化剂的晶体结构和还原特性也与催化剂上镍的负载量有关。焙烧过程中样品10Ni/MgO上镍前体与载体前体发生了两种相互作用, 并且其氧化态与其他催化剂相比具有特殊的结构和还原性。说明催化剂的选择性不仅受活性相Ni的影响而且受Ni活性相周围环境的影响。     

花状微球NiO/CeO_2催化剂上乙醇水蒸气重整制氢研究

用水热法制备微米尺寸CeO2花状微球粉体,并通过浸渍/热分解法在该粉体上担载纳米尺寸的NiO颗粒,制得催化剂NiO/CeO2。对催化剂进行了XRD、SEM、XES和BET物性表征。经固定床反应器对催化剂的催化性能进行测试。装载1.0 g催化剂,液体处理量0.05 mL/min。结果表明,该方法合成的催化剂NiO/CeO2对低温乙醇水蒸气重整反应表现出较高的活性和稳定性。同时通过微量Cr、Zn、Cu的加入在低温区抑制了CO、CH4的生成,提高了H2的产率和催化剂的抗积炭能力。该催化剂连续稳定性测试达到2 000 h;进行反复起动稳定性测试12次后,未表现出失活特征。     

负载Ni催化剂上低温甘油蒸汽重整制氢

采用等体积浸渍法制备了Al₂O₃、CeO₂、TiO₂及MgO负载Ni催化剂,考察了它们对甘油蒸汽重整制氢反应的催化性能。采用X射线衍射、N₂吸附、透射电镜及H₂程序升温还原等方法对催化剂进行了表征。结果表明,载体对Ni催化剂的活性有显著影响。在400 ℃下Ni/CeO₂的催化活性明显好于其他催化剂,活性次序为Ni/CeO₂> Ni/Al₂O₃ > Ni/TiO₂ ~ Ni/MgO。Ni/CeO₂也具有好的稳定性,反应20 h未见活性下降,甘油转化率70%,氢气收率69.2%。这与CeO₂的本性及其与活性组分的相互作用有关。Al₂O₃具有较大的比表面积与孔体积,有利于CO吸附及甲烷化反应的进行,使得Ni/Al₂O₃催化剂在较高温度下具有很高的甘油转化率85.7%,但H₂选择性较差。由于MgO载体与活性组分强的相互作用而生成NiMgO₂固溶体,导致Ni/MgO低温活性差。     

Low CO content hydrogen production from oxidative steam reforming of ethanol over CuO-CeO2 catalysts at low-temperature

CuO-CeO₂ catalysts were prepared by a urea precipitation method for the oxidative steam reforming of ethanol at low-temperature. The catalytic performance was evaluated and the catalysts were characterized by inductively coupled plasma atomic emission spectroscopy, X-ray diffraction, temperature-programmed reduction, field emission scanning electron microscopy and thermo-gravimetric analysis. Over CuO-CeO₂ catalysts, H₂ with low CO content was produced in the whole tested temperature range of 250–450 °C. The non-noble metal catalyst 20CuCe showed higher H₂ production rate than 1%/oRh/CeO₂ catalyst at 300–400 °C and the advantage was more obvious after 20 h testing at 400 °C. These results further confirmed that CuO-CeO₂ catalysts may be suitable candidates for low temperature hydrogen production from ethanol.     

Autothermal reforming of methane over Ni catalysts supported over ZrO2-CeO2-Al2O3

Ni catalysts supported on Al2O3, ZrO2-Al2O3, CeO2-Al2O3 and ZrO2-CeO2-Al2O3 were prepared by coprecipitation method, and their catalytic performances for autothermal reforming of methane to hydrogen were investigated. The Ni-supported catalysts were characterized by XRD, TPR and XPS. The relationship between the structures and catalytic activities of the catalysts was discussed. The results showed that the catalytic activity and stability of the Ni/ZrO2-CeO2-Al2O3 catalyst was better than those of other catalysts with the highest CH4 conversion, H2/CO and H2/COx ratio at 750 ℃. The catalyst showed a little deactivation along the reaction time during its 72 h on stream with the mean deactivation rate of 0.08%/h. The catalytic performance of the Ni/ZrO2-CeO2-Al2O3 catalyst was also affected by reaction temperature, no2 ： nCH4 molar ratio and nH2O ： nCH4 molar ratio. TPR, XRD and XPS measurements indicated that the formation of ZrO2-CeO2 solid solution could improve the dispersion of NiO, and inhibit the formation of NiAl2O3, and thus significantly promoted the catalytic activity of the Ni/ZrO2-CeO2-Al2O3 catalyst.     

Hydrogen generation from steam reforming of ethanol in dielectric barrier discharge

Dielectric barrier discharge (DBD) was used for the generation of hydrogen from ethanol reforming. Effects of reaction conditions, such as vaporization temperature, ethanol flow rate, water/ethanol ratio, and addition of oxygen, on the ethanol conversion and hydrogen yield, were studied. The results showed that the increase of ethanol flow rate decreased ethanol conversion and hydrogen yield, and high water/ethanol ratio and addition of oxygen were advantageous. Ethanol conversion and hydrogen yield increased with the vaporization room temperature up to the maximum at first, and then decreased slightly. The maximum hydrogen yield of 31.8% was obtained at an ethanol conversion of 88.4% under the optimum operation conditions of vaporization room temperature of 120 ?C, ethanol flux of 0.18 mL/min, water/ethanol ratio of 7.7 and oxygen volume concentration of 13.3%.     

Kinetic behaviour of commercial catalysts for methane reforming in ethanol steam reforming process

Ethanol steam reforming has been studied in a fluidized bed （in order to ensure bed isothermicity） on commercial catalysts for methane reforming. The results allow analyzing the effect of temperature （in 300-700℃ range）, and both metal and support nature on the reaction indices （ethanol conversion, yields and selectivities to H2 and byproducts （CO2, CO, CH4 and C2H4O））. Special attention has been paid to catalysts＇ stability by comparing the evolution of the reaction indices with time on stream at 500°C （minimum CO formation） and 700℃ （minimum deactivation by coke deposition）. Although they provide a slightly lower H2 yield, the results evidence a good behaviour of Ni based catalysts, indicating that they are an interesting alternative of more expensive Rh based ones.     

甲烷自热重整制氢热力学分析

为了优化甲烷自热重整制氢过程的反应条件,运用吉布斯自由能最小化方法对过程进行了热力学计算,研究了重整过程的反应温度、空碳比、水碳比对平衡组成的影响。模拟结果表明,适宜的水碳比为2.5～3.5,空碳比2.0～3.5,重整温度700℃～850℃,每摩尔甲烷生成2.17mol～2.23mol氢;以水碳比1.5为例,对不同空碳比下的组分的产生和转化的机理进行了分析。     

Hydrogen production via steam reforming of bio-oil model compounds over supported nickel catalysts

The steam reforming of four bio-oil model compounds(acetic acid,ethanol,acetone and phenol) was investigated over Ni-based catalysts supported on Al2O3 modified by Mg,Ce or Co in this paper.The activation process can improve the catalytic activity with the change of high-valence Ni(Ni2O3,NiO) to low-valence Ni(Ni,NiO).Among these catalysts after activation,the Ce-Ni/Co catalyst showed the best catalytic activity for the steam reforming of all the four model compounds.After long-term experiment at 700°C and the S/C ratio of 9,the Ce-Ni/Co catalyst still maintained excellent stability for the steam reforming of the simulated bio-oil(mixed by the four compounds with the equal masses).With CaO calcinated from calcium acetate as CO2 sorbent,the catalytic steam reforming experiment combined with continuous in situ CO2 adsorption was performed.With the comparison of the case without the adding of CO2 sorbent,the hydrogen concentration was dramatically improved from 74.8% to 92.3%,with the CO2 concentration obviously decreased from 19.90% to 1.88%.     

负载NiO-Fe2O3的凹凸棒石对生物油模型物催化重整制氢性能的影响

利用共沉淀法,制备一系列在凹凸棒土上负载不同含量的NiO-Fe₂O₃催化剂。以乙酸、乙醇和苯酚的水溶性溶液为生物油模型物,在自制的三段式固定床反应器中,考察了NiO-Fe₂O₃的负载量、反应温度、水碳比(S/C)对生物油模型物重整制氢的影响。结果表明,所获得的氢气产率最高的工艺条件为,在650℃条件下,以水碳比8~10的生物油模型为实验原料,使用自制的50%NiO-50%Fe₂O₃/PG型催化剂,可使气体产物中H₂的相对含量达到最大66.15%。     

Ni/Al2O3和Ni/La2O3催化剂上低温乙醇水蒸气重整制氢

 采用浸渍、热分解和氢还原等步骤制备了两种纳米晶载体催化剂Ni/Al2O3和Ni/La2O3,应用X射线衍射、X射线光电子能谱、N2吸附和扫描电镜对催化剂的体相和表面结构进行了测定,采用固定床反应器考察了催化剂对乙醇水蒸气重整制氢反应的催化性能. 实验结果表明, 15.3%Ni/La2O3催化剂对乙醇的低温水蒸气重整反应表现出较高的催化活性和稳定性. 250 ℃时乙醇的转化率已达到80.7%,氢气的选择性为49.5%; 330 ℃时乙醇的转化率达到100%,氢气的选择性可达54.3%. 16.1%Ni/Al2O3催化剂对低温乙醇水蒸气重整反应的催化活性较低.     

Catalytic removal of nitric oxides from diesel exhaust over supported metal oxides catalysts

Summary A number of supported metal oxide catalysts were prepared and tested for nitrogen oxide removal from diesel engine exhaust. More than 50% of nitrogen oxides were removed using many prepared catalysts in the temperature range of 150^oC-350^oC.     

Effect of CeO2 on the catalytic performance of Ni/Al2O3 for autothermal reforming of methane

The effect of promoter Ce on the catalytic performance of Ni/Al2O3 catalyst for autothermal reforming of methane to hydrogen was investigated. The catalysts were characterized by X-ray diffraction （XRD）, temperature-programmed reduction （TPR）, and X-ray photoelectron spectroscopy （XPS）. The results indicated that the catalytic performance of the catalysts was improved with the addition of Ce. Ni/Ce30Al70Oδ showed the highest CH4 conversion in operation temperatures ranging from 650 ℃ to 850 ℃. At the same time, the decrease in H2/CO ratio with increasing reaction temperature was consistent with the fact that water-gas shift reaction was thermodynamically unfavorable at higher temperatures. The XRD result indicated that adding Ce to Ni/Al2O3 catalyst prevented the formation of NiAl2O4 and facilitated the formation of NiO. The formation of NiO increased the number of active sites, resulting in higher activity. Comparing the TPR profiles of Ni/Ce30Al70Oδ with Ni/Al2O3, it could be clearly observed that with the addition of Ce, the total reduction peak areas in the middle and low temperatures increased. It was most probably that the addition of Ce inhibited the stronger interaction between Ni and Al2O3 to form the phase of NiAl2O4, and favored the formation of the strong interaction between NiO species and CeO2. Therefore, the addition of Ce to the Ni/Al2O3 catalyst increased the active surface that promoted the activity of the catalyst.     

有机蒙脱土负载镍催化剂上乙醇重整制氢

采用浸渍法制备了有机改性蒙脱土(OMt)负载的Ni/有机蒙脱土(Ni/OMt)催化剂,用于乙醇重整制氢;通过XRD、FT-IR、H₂-TPR、SEM、XPS和氮吸附等手段对催化剂进行了表征分析。结果表明,与未改性的蒙脱土负载的Ni催化剂(Ni/MMT)相比,有机改性可显著提高其比表面积、孔容和金属Ni的分散度,降低碳沉积量,改善Ni/MMT催化剂的稳定性。Ni/OMt催化剂表现出较高的乙醇重整制氢催化性能,在773K下反应30 h,乙醇转化率保持在100%,氢气选择性为70%;而Ni/MMT催化剂在反应10 h即开始失活,碳沉积严重,同时产生副产物乙烯和乙醛。使用十六烷基三甲基溴化铵(CTAB)改性可促进Ni高分散在MMT层板上,抑制积炭对活性金属Ni包裹,提高其乙醇重整氢气选择性、降低乙烯和乙醛的选择性。