Flow injection on-line spectrophotometric determination of thorium(IV) after preconcentration on XAD-4 resin impregnated with oxytetracycline

A very sensitive, selective and simple flow injection time-based method was developed for on-line preconcentration and determination of thorium(IV) at micro g L^–1 levels in environmental samples. The system operation was based on thorium(IV) ion retention at pH 4.0 in the minicolumn at a flow rate of 15.2 mL min^–1. The trapped complex was then eluted with 3.6 mol L^–1 HCl at a flow rate of 4.9 mL min^–1. The amount of thorium(IV) in the eluate was measured spectrophotometrically at 651 nm using arsenazo-III solution (0.05 % in 3.6 mol L^–1 HCl stabilized with 1 % triton X-100, 4.9 mL min^–1) as colorimetric reagent. All chemical, and flow injection variables were optimized for the quantitative preconcentration of metal and a study of interference level of various ions was also carried out. The system offered low backpressure and improved sensitivity and selectivity. At a preconcentration time of 60 s and a sample frequency of 40 h^–1, the enhancement factor was 97, the detection limit was 0.25 μg L^–1, and the precision expressed as relative standard deviation was 1.08 % (at 50 μg L^–1), whereas for 300 s of the preconcentration time and a sample frequency of 10 h^–1, the enhancement factor of 357, the detection limit (3σ) of 0.069 μg L^–1 and the precision of 1.32 % (at 10 μg L^–1) was reported. The accuracy of the developed method was sufficient and evaluated by the analysis of certified reference material IAEA-SL-1 (Lake Sediment) and spiked water samples.     

Flow injection on-line determination of uranium after preconcentration on XAD-4 resin impregnated with dibenzoylmethane

A flow injection on-line determination of uranium(VI) after preconcentration in a minicolumn having amberlite XAD-4 resin impregnated with dibenzoylmethane (DBM) is described. Uranium(VI) is selectively adsorbed from aqueous solution of pH 5.5 in the minicolumn (5.5 cm long with 5.0 mm i.d.) at a flow rate of 13.6 mL min⁻¹. The uranium(VI) complex was desorbed from the resin by 0.1 mol dm⁻³ HCl at a flow rate of 4.2 mL min⁻¹ and mixed with arsenazo-III solution (0.05% solution in 0.1 mol dm⁻³ HCl, 4.2 mL min⁻¹), and taken to the flow through cell of spectrophotometer where its absorbance was measured at 651 nm. Various parameters affecting the complex formation and its elution were optimized. Peak height (absorbance) was used for data analyses. The preconcentration factors of 36 and 143, detection limits of 0.9 and 0.232 μg L⁻¹, sample throughputs of 40 and 10 were obtained for preconcentration time of 60 and 300 s, respectively. The tolerance limits of many interfering cations like Th(IV) and rare-earth elements were improved. The proposed method was applied on different water (spiked tap, well and sea water) and biological samples and good recovery was obtained. The method was also validated on mocked uranium ore sample and the results were in good agreement with the reported value.     

Online thorium determination after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine by FI-spectrophotometry

A very sensitive and selective flow injection on-line determination method of thorium (IV) after preconcentration in a minicolumn having XAD-4 resin impregnated with N-benzoylphenylhydroxylamine is described. Thorium (IV) was selectively adsorbed from aqueous solution of pH 4.5 in a minicolumn at a flow rate of 13.6 mL min^?1, eluted with 3.6 mol dm^?3 HCl (5.6 mL min^?1), mixed with arsenazo-III (0.05% in 3.6 mol dm^?3 HCl stabilized with 1% Triton X-100, 5.6 mL min^?1) at confluence point and taken to the flow through cell of spectrophotometer where its absorbance was measured at 660 nm. Peak height was used for data analyses. The preconcentration factors obtained were 32 and 162, detection limits of 0.76 and 0.150 ??g L^?1, sample throughputs of 40 and 11 h^?1 for preconcentration times of 60 and 300 s, respectively. The tolerance levels for Zr(IV) and U(VI) metal ions is increased to 50-folds higher concentration to Th(IV). The proposed method was applied on different spiked tap water, sea water and biological sample and good recovery was obtained. The method was also applied on certified reference material IAEA-SL1 (Lake Sediment) for the determination of thorium and the results were in good agreement with the reported value.     

Online separation and preconcentration of trace heavy metals with 2,6-dihydroxyphenyl-diazoaminoazobenzene impregnated amberlite XAD-4

A rapid and sensitive flow injection online preconcentration method was developed for determination of Cd, Co, Cu, and Zn in natural water samples by flame atomic absorption spectrometry. The procedure is based on the retention of analytes in the form of 2,6-dihydroxyphenyl-diazoaminoazobenzene (DHDAA) complexes on a microcolumn packed with XAD-4-DHDAA resin. Cd, Co, Cu, and Zn can be eluted from the microcolumn with 0.5 mol L⁻¹ HCl and pumped directly to the nebulizer-burner system of the flame atomic absorption spectrometer (FAAS). The enrichment factors are 42 (Cd), 33 (Co), 28 (Cu), and 31 (Zn), for a sample volume of 6.0 mL and 1 min preconcentration time relative to direct introduction of aqueous solutions into an atomic absorption spectrometer. The sampling frequency was 30 h⁻¹ with a 1 min loading. The proposed method allowed the determination of Cd, Co, Cu, and Zn with detection limits of 0.1, 0.5, 0.3, and 0.2 μg L⁻¹, respectively. The selectivity of the XAD-4-DHDAA resin for Cd, Co, Cu, and Zn over several electrolytes was also investigated. The method was validated by analysis of a standard reference material (GBW 08301) with the results agreement with those quoted by manufactures. The developed method was applied to the determination of trace Cd, Co, Cu, and Zn in tap water, ground water and river water samples with satisfactory results.     

Flame atomic absorption spectrometric determination of silver after preconcentration on Amberlite XAD-16 resin from thiocyanate solution

A method of silver preconcentration by using a column containing Amberlite XAD-16 resin and this future determination by a flame AAS after elution is proposed. The effect of the factors such as pH, the nature of complexing agent, sample volume, flow rate, the type and concentration of elution solution on the preconcentration efficiency have been investigated. The influence of some matrix elements on the recovery of silver were also examined. It was found, that the quantitative recovery of thiocyanate complex of silver was obtained from nitric acid solution (pH 2) as 99.20+/-0.07% at the 95% confidence level. A preconcentration factor up to 75 could be obtained. The detection limit of silver was 0.047 mg l(-1). The adsorption of silver onto Amberlite XAD-16 can be formally described by a Langmuir equation with maximum adsorption capacity 4.66 mg g(-1) (0.043 mmol g(-1)). The proposed method was applied to determination of silver in standard alloy with relative error 6.25%.     

Development of method for determination and preconcentration of uranium in water samples using XAD-4 resin loaded with Br-PADAP

In the present work, a minicolumn of XAD-4 loaded with 2-(5-bromo-2-pyridylazo)-5-(diethylamino)-phenol (Br-PADAP) is proposed as a preconcentration system for uranium determination in well, tap and mineral water samples by spectrophotometer using arsenazo III as the chromogenic reagent. Initially, a two-level (2³) full factorial design was used for the preliminary evaluation of three factors, involving the following variables: sampling flow rate, elution flow rate, and pH. This design has revealed that, for the studied levels, buffer concentration and pH were significant factors. When the experimental conditions established in the optimization step were pH = 8.6, and an elution flow rate of 8.6 mL min^?1 using 0.5% m/v ascorbic acid, this system has allowed for the determination of uranium with a detection limit (LOD) (3σ/S) of 0.05 μg L^?1 and a quantification limit (LOQ) (10σ/S) of 0.16 μg L^?1. The precision expressed as the relative standard deviation (R.S.D.) of 0.8% and 1.9% at 10.0 and 1.0 μg L^?1, respectively- and a preconcentration factor of 184.5 for a sample volume of 50.0 mL. Accuracy was confirmed by uranium determination in the standard reference material, NIST SRM 1566b trace element units in Oyster Tissue samples, and spike tests with recuperations ranging from 93.2 to 105%; the procedure were applied for uranium determination in tap water, well water, and drinking water samples collected from Caetité and Cruz das Almas Cities, Bahia, Brazil. Five water samples were analyzed the uranium concentrations varied from 0.50 to 2.07 μg L^?1     

On-line preconcentration,ion chromatographic separation and spectrophotometric determination of palladium at trace level

A new method for the determination of Pd by ion chromatography and spectrophotometric detection has been developed. The technique is based on the separation of palladium as PdCl4(2-) by anion exchange and on the detection, at a wavelength of 407 nm, of metal as PdI4(2-) after a post-column reaction with KI. The column used was an IonPac AS4 with HCl and HClO4 eluents. The eluent concentration and composition of post-column reagent were optimised in order to obtain the best separation and sensitivity for Pd. In order to reduce the detection limit, an on-line preconcentration step, has been optimised. The method, as developed, was suitable for palladium determination within a 300 ng/l D.L. value. The method applied to a BCR reference material (CRM 277, estuarine sediment) gave satisfactory results in agreement with the certified value within a D.L. value of 1.3 microg/l for the real sample.     

Speciation analysis of chromium by separation on a 5-palmitoyl oxine-functionalized XAD-2 resin and spectrophotometric determination with diphenylcarbazide

The method developed in this work for the separation and preconcentration of Cr(III) is based on its retention by an Amberlite XAD-2 copolymer resin functionalized with 5-palmitoyl-8-hydroxyquinoline (oxine), abbreviated XAD-POx, with the ligand covalently bound to the copolymer. Cr(III) sorption was quantitative within the pH range 4.5–7.0 and Cr(VI) was not retained. The Cr(III) held by the resin column was eluted with a hot solution of H₂O₂ in pH9.0 aqueous NH₃–NH₄Cl buffer, and Cr oxidized to CrO₄^2– was rejected by the chelating cation-exchanger column. Any Cr(VI) originally present with Cr(III) could be reduced with an acidic solution of H₂O₂, and retained by the column yielding total Cr results, Cr(VI) being determined from the difference. The resin showed a maximal preconcentration factor of 60 for Cr(III), the LOD and LOQ being 9.3 and 30.1 nmol L^–1, respectively. The developed preconcentration-speciation analysis was finished with a diphenylcarbazide (DPC) spectrophotometric procedure suitable for conventional laboratories. The resin showed excellent salt tolerance, enabling Cr analysis in seawater, and was stable over extended use. All the interferents of this procedure that normally occur in an electroplating effluent, a blended coal CRM, and a standard steel sample could be removed by the recommended procedure, by use of partial and total selectivity at the adsorption and desorption stages, respectively, enabling preconcentration and colorimetric determination of chromium in various complex matrices.     

FI-spectrophotometric determination of uranium after preconcentration on an anion exchange resin

An economical, fast, sensitive and selective method for the determination of uranium (VI) from sulfate media based on the flow injection on-line preconcentration in a minicolumn having amberlite IRA-402 (strong anion exchange) resin is described. Uranium (VI) was selectively adsorbed on the resin as uranyl trisulfate complex from aqueous solution of pH 2 in the minicolumn (2.56 mm i.d. and 7.5 cm in length) at a flow rate of 10 ml min^?1. The adsorbed uranyl trisulfate complex was eluted by HClO₄ (0.1 mol l^?1, 6.5 ml min^?1) and mixed with arsenazo-III (0.05 %, 6.5 ml min^?1), and passed through the flow through cell of spectrophotometer where its absorbance was measured at 653 nm. Various parameters affecting adsorption and elution of the uranium complex were optimized. For data analyses peak absorbance was used. For 60 and 180 s preconcentration time, enrichment factors (EF) 20 and 40, sampling frequency (SF) 45 and 18 h^?1; and detection limits (DL) (3σ) 14.2 and 8.6 μg l^?1 were obtained, respectively. To enhance the sensitivity of the system, two minicolumns (described above) were used for simultaneous preconcentration and elution purpose. For 60 and 180 s preconcentration time, EF 30 and 50, SF 42 and 17 h^?1 and DL (3σ) 4.4 and 3.44 μg l^?1 were obtained, respectively. The effect of various anions and cations was studied for single column manifold. High selectivity of this method was observed. All the anions and cations studied did not interfere up to 330 times higher mass ratio to 300 μg l^?1 U (VI) except Th(IV) which was tolerated up to 133 times by the addition of washing step in the manifold. The method based on single column manifold was applied on the spiked tap water, biological sample CRM (IAEA-V4) and synthetic leach liquor solution and good recovery was obtained. The method based on dual column manifold was validated on lake sediment SL-1 (CRM) and the results obtained were in good agreement at 95 % confidence level with the given value.     

Spectrophotometric determination of trace amounts of tungsten in geological samples after preconcentration on Amberlite XAD-1180

A method for the preconcentration of trace amounts of tungsten as its thiocyanate complex, using a column filled with Amberlite XAD-1180 resin, is proposed. After elution with a small volume of acetone, the analyte was determined spectrophotometrically with potassium thiocyanate and stannous chloride. The influence of several ions, as interferents, is discussed. The proposed method was applied to the determination of tungsten in geological samples with good analytical results, such as recoveries of 95% or above, relative standard deviations of 6% or below (n = 10) and a detection limit of 12 mugl(-1).     

Sorption studies of U(VI) on Amberlite XAD-2 resin impregnated with Cyanex272

U(VI) sorption from nitric media using Cyanex272 impregnated on Amberlite XAD-2 resin has been studied using batch method. The influence of different experimental parameter such as aqueous acidity, effect of time, influence of eluting agents on U(VI) uptake was evaluated. The maximum sorption capacity of 0.168?mmol?g^?1 of U(VI) evaluated based upon these studies. Sorption of U(VI) follows both the Langmuir and Freundlich adsorption isotherms.     

On-line aluminium preconcentration on chelating resin and its FIA-spectrofluorimetric determination in foods and dialysis concentrates

A new, sensitive and rapid spectrofluorimetric flow-injection method, is presented for the determination of trace levels of aluminium based on the formation of a fluorescent complex between aluminium and 5,7-dibromo-8-quinolinol (DBQ) and its extraction into diethylether (λ_exc = 400 nm, λ_em = 525 nm). Experimental conditions such as pH, reagent concentration, flow-rates, sample volume, extraction coil length, etc., have been optimized for on-line and batch procedures. The detection limits are 1 ppb and 0.3 ppb for batch and on-line systems respectively. The coeflicient of variation is 3.0% at the 4 ppb level for the FIA system. To remove interferences and to preconcentrate aluminium, a chelating resin microcolumn which was able to selectively complex A1(III) and was obtained by immobilizing Chromotrope 2B on AG1-X8 ion-exchange resin, was incorporated into the FIA system. The proposed method was successfully applied to determine aluminium in tap water, food samples and dialysis solutions.     

Spectrophotometric determination of lead after preconcentration of its diphenylthiocarbazone complex on an Amberlite XAD-1180 column

A simple methodology has been developed for the solid phase extraction of lead based on the adsorption of its diphenylthiocarbazone complex on an Amberlite XAD-1180 column. The effect of various parameters such as eluting agents, stability of the column, sample volume, interfering ions, etc. were studied in detail. The adsorbed complex could be eluted using acetone and the concentration of lead was determined using visible spectrophotometry at a wavelength maximum of 486nm. A detection limit of 3.5microgL(-1) could be achieved and the validity of the proposed method was checked in spiked tap water, well water and industrial wastewater samples. The relative standard deviation of the method was found to be 3.0%. The highest preconcentration factor attainable for quantitative recovery (>95%) of lead was 25 for a 250mL sample volume.     

On-line preconcentration with different solid adsorbents for lead determination

An on-line column preconcentration method based on the combined use of ammonium O,O-diethyldithiophosphate and activated carbon or polyurethane foam as adsorbents has been developed for the determination of Pb in water samples. The complexed Pb was eluted with ethanol and determined by flame atomic absorption spectrometry. The optimum preconcentration conditions are given for each adsorbent. The enrichment factors were 63 and 294, and the detection limits (3sigma) 3 microg L(-1) and 0.8 microg L(-1), respectively, for the carbon and foam systems. When the optimized procedures were applied to the determination of Pb in water samples the recovery efficiency was > 96%.     

On-line preconcentration with different solid adsorbents for lead determination

An on-line column preconcentration method based on the combined use of ammonium O,O-diethyldithiophosphate and activated carbon or polyurethane foam as adsorbents has been developed for the determination of Pb in water samples. The complexed Pb was eluted with ethanol and determined by flame atomic absorption spectrometry. The optimum preconcentration conditions are given for each adsorbent. The enrichment factors were 63 and 294, and the detection limits (3σ) 3?μg?L^–1 and 0.8?μg?L^–1, respectively, for the carbon and foam systems. When the optimized procedures were applied to the determination of Pb in water samples the recovery efficiency was > 96%.     

Determination of some trace metals in waters by flame atomic absorption spectrometry after preconcentration on Amberlite XAD-16 resin with sodium tetraborate

A method was described for the determination of the elements Cr, Mn, Fe, Co, Ni, Cu, Cd, Pb, and Bi in waters by flame atomic absorption spectrometry (FAAS) after separation and preconcentration on Amberlite XAD-16 resin with sodium tetraborate using a chromatographic column. Parameters influencing the analytical performance, including pH and the volume of sample, amount of analyte and interfering effect of co-existing ions, were studied in detail. The recovery values were quantitative (> or = 95%), and the relative standard deviation (RSD) and detection limit (DL) varied in the range of 1.1-2.4% (n=10) and 0.002-0.177 microg m(-1) (3s, n=20), respectively. After being optimized, the proposed method was applied to the drinking water, waste water and artificial sea water samples. Recovery values of the elements investigated, were quantitative for tap water and synthetic sea water, except for Mn, Co and Ni (including also Cd for synthetic sea water). Recovery values of Cd, Pb, Cu and Co were found to be 95, 102, < or = 87, and < or = 83%, respectively, for the waste water samples.     

阴离子树脂苯取富集-分光光度法测定煤矸石中痕量钪

研究了对乙酰基偶氮氯膦(CPApA)与钪(Ⅲ)的显色反应,在HNO3介质中,在Triton X-100存在下,CPApA与钪(Ⅲ)反应生成摩尔比为1:1的稳定配合物,该配合物可用717型阴离子树脂交换柱萃取富集,再通过树脂相光度法测定钪,由此建立了测定钪的新方法.吸附配合物树脂相的最大吸收波长为690 nm,表观摩尔吸光系数为9.56×105 L·mol-1·cm-1.钪的质量浓度在0～480μg/L范围内符合比耳定律.经阴离子树脂交换柱萃取富集后,钪的测定灵敏度可提高数倍,大多数常见离子不干扰测定.方法应用于煤矸石痕量钪的测定,结果满意.样品分析结果的相对标准偏差小于5%,加标回收率为96.0%～102.5%.     

Copper determination in natural water samples by using FAAS after preconcentration onto amberlite XAD-2 loaded with calmagite

A procedure for separation and preconcentration of trace amounts of copper in natural water samples, has been proposed. It is based on the adsorption of copper(II) ions onto a column of Amberlite XAD-2 resin loaded with calmagite reagent. This way amounts of copper within the range from 0.0125 to 25.0 μg, in a sample volume of 25 to 250 ml, and pH from 3.7 to 10.0 was concentrated as calmagite complex in a column of 0.50 g of Amberlite XAD-2 resin. Copper (II) ion was desorpted by using 5.0 ml of 2 mol l⁻¹ hydrochloric acid. Detection and determination limits of the proposed procedure for 250 ml sample volume were 0.15 and 0.50 μg l⁻¹, respectively. Selectivity test showed that (in the indicated concentration), calcium(II) (500 mg l⁻¹), magnesium(II) (500 mg l⁻¹), strontium(II) (50 mg l⁻¹), iron(III) (10 mg l⁻¹), nickel(II) (10 mg l⁻¹), cobalt(II) (10 mg l⁻¹), cadmium(II) (10 mg l⁻¹) and lead(II) (10 mg l⁻¹) did not interfere in copper determination by this procedure. Precision of the method, evaluated as the relative standard deviation by analyzing a series of seven replicates, was 2.42% for a copper mass of 1.0 μg in a sample volume of 100 ml. The accuracy of the proposed procedure was evaluated by means of copper determination in reference biological samples. The achieved results were in good agreement with certified values. The extractor system had a sorption capacity of 1.59 μmol of copper per gram of resin loaded with calmagite. The proposed procedure was applied for copper determination by FAAS in natural water samples. Samples were collected from different places of Salvador city, Bahia, Brazil. The achieved recovery, measured by the standard addition technique, showed that the proposed procedure had good accuracy. A good enrichment factor (50×) and simplicity are the main advantages in this analytical procedure.     

Atomic absorption spectrophotometric determination of gold with preconcentration by Donnan dialysis

Donnan dialysis enrichment with tubular cation-exchange membrane was used as a preconcentration method prior to determination of gold by flame atomic absorption spectrometry (FAAS). The value of enrichment factor can be controlled for a particular application through adjustment of the membrane tuning length, dialysis time, carrier flow rate, composition of the receiver solution and by addition of complexing ligand to the receiver or the sample solution. For 10 min dialysis enrichment factor above 3 can be achieved. The detection limit (signal-to-noise ratio = 3) of 35 ng/ml was obtained. RSD at 0.2 mug/ml level was 4.7% (n = 6). The results of dialysis of noble metals mixtures are demonstrated.     

Geobacillus thermoleovorans immobilized on Amberlite XAD-4 resin as a biosorbent for solid phase extraction of uranium (VI) prior to its spectrophotometric determination

Geobacillus thermoleovorans subsp stromboliensis, was immobilized on an Amberlite XAD-4 ion exchanger and used as a solid phase extractant for the preconcentration of U(VI) ions prior to their determination by UV-VIS spectrophotometry. Parameters affecting the preconcentration (such as the pH value of the sample solution, the concentration of U(VI), the volume and type of eluent, the flow rate and the effect of potentially interfering ions) were studied. The optimum pH for the sorption of U(VI) was found to be pH 5.0. 5.0?mL of 1 M hydrochloric acid were used to eluate the U(VI) from the column. The loading capacity is 11?mg?g^?1. The limits of detection and quantification are 2.7 and 9.0?μg?L^?1, respectively, and relative standard deviations are <10?%. The method was applied to the determination of U(VI) in a certified reference sample (NCS ZC-73014; tea leaves) and in natural water samples.