Blank values, adsorption, pre-concentration, and sample preservation for arsenic speciation of environmental water samples

Arsenic is the focus of public attention because of its toxicity. Arsenic analysis, its toxicity, and its fate in the environment have been broadly studied, still its blank values, adsorption to sampling materials and pre-concentration of water samples as well as stabilization of arsenic compounds in water samples under field conditions have been very little investigated. In this study, we investigate the blank values and adsorption of arsenic compounds for different laboratory materials. We focused our work onto pre-concentration of water samples and how to stabilize arsenic compounds under field conditions. When using glassware for arsenic analysis, we suggest testing arsenic blank values due to the potential release of arsenic from the glass. Adsorption of arsenic compounds on different laboratory materials (<10%) showed little influence on the arsenic speciation. Pre-concentration of methanol-water solutions could result in potential overestimation of arsenic compounds concentrations. Successful pre-concentration of water samples by nitrogen-purge provides an analytical possibility for arsenic compounds with high recoveries (>80%) and low transformation of arsenic compounds. Thus, concentrations as low as 1 ng As l⁻¹ can be determined. Addition of ethylenediaminetetraacetic acid (EDTA) and storage in the dark can decrease the transformation among arsenic compounds in rainwater and soil-pore water for at least a week under field conditions.     

Simultaneous determination of arsenic, selenium and antimony species using HPLC/ICP-MS

A new method for the simultaneous separation and determination of four arsenic species [As(III), As(V), monomethylarsonic acid and dimethylarsinic acid], three selenium species [Se(IV), Se(VI) and selenomethionine] as well as Sb(III) and Sb(V) is presented. The speciation was achieved by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Chromatographic parameters such as the composition and pH of the mobile phase were optimised. Limits of detection are below 4.5 μg L^–1 (as element) for Sb(III) and the selenium species and below 0.5 μg L^–1 for the other species. Precisions of retention times were better than 2% RSD and of peak areas better than 8% RSD for all the species investigated. Received: 13 January 1999 / Accepted: 4 March 1999     

Simultaneous determination of arsenic, selenium and antimony species using HPLC/ICP-MS

A new method for the simultaneous separation and determination of four arsenic species [As(III), As(V), monomethylarsonic acid and dimethylarsinic acid], three selenium species [Se(IV), Se(VI) and selenomethionine] as well as Sb(III) and Sb(V) is presented. The speciation was achieved by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Chromatographic parameters such as the composition and pH of the mobile phase were optimised. Limits of detection are below 4.5 μg L^–1 (as element) for Sb(III) and the selenium species and below 0.5 μg L^–1 for the other species. Precisions of retention times were better than 2% RSD and of peak areas better than 8% RSD for all the species investigated.     

液相色谱-双通道原子荧光检测联用法同时测定砷和硒的形态

建立了一种利用高效液相色谱-双通道原子荧光检测联用同时进行砷和硒形态分析的方法。以10 mmol/L NH4H2PO4溶液(pH 5.6)(添加2.5%(体积分数)的甲醇)为流动相,在12 min内同时分离了三价砷(As(III))、一甲基砷(MMA)、二甲基砷(DMA)、五价砷(As(V))、硒代胱氨酸(SeCys)、硒代蛋氨酸(SeMet)和四价硒［Se(IV)］等化合物。As(III)、DMA、MMA、As(V)、SeCys、SeMet和Se(IV)的检出限分别为1,3,2,3,4,18和3 μg/L (进样量为200 μL),5次测定的相对标准偏差为1.9%～6.1%(As 100 μg/L, Se 300 μg/L)。应用该方法对人体尿样及硒酵母片中砷和硒的形态进行了分析,目标物在尿样中的加标回收率为83%～108%,在硒酵母片中的加标回收率为88%～105%。实验结果表明,该方法可用于尿样及药品中砷和硒形态的日常分析。该方法减少了样品的分析时间和试剂用量,降低了工作强度,提高了工作效率。     

Simultaneous determination of arsenic, manganese, and selenium in biological materials by neutron-activation analysis

A new method was developed for the simultaneous determination of arsenic, manganese, and selenium in biological material by thermal-neutron activation analysis. The use of (81 m)Se as indicator for selenium permitted a reduction of activation time to 1 hr for a 1 g sample, and the possibility of loss of volatile compounds during irradiation could be dismissed. No pretreatment of the sample is required, and the radiochemical separation scheme is based on simple chemical operations, completed in less than 3 hr. A systematic experimental investigation of the performance characteristics of the method was carried out, including studies of the accuracy of the results. The actual precision achieved in routine application of the method in the analytical laboratory was in good agreement with the calculated precision, and the results are therefore well suited for statistical evaluation of differences at the ppM level in samples of biological tissue.     

Assessment of matrix-dependent analyte stability and volatility during open-vessel sample dissolution for arsenic, cadmium, mercury and selenium

A sensitive method for the determination of estradiol is presented that is based on an electrode modified with multi-walled carbon nanotubes (MWNTs) along with an ionic liquid. The resulting electrode showed more sensitive voltammetric response to estradiol than other electrodes modified with MWNTs. The peak current for estradiol is linearly related to concentration over two decades, and the limit of detection is 5 nM. The method was applied to the determination of estradiol in rabbit blood serum and in environmental waters. The recoveries were 95.3–104.0% and 97.0–104.7%, respectively.     

Investigation on stability and preservation of arsenic species in iron rich water samples

Important for the accurate and reproducible determination of inorganic redox forms of arsenic in iron-rich waters is their conservation prior to analysis. Species and trace element analysis methods are commonly laboratory based. Stabilisation of samples is necessary for subsequent laboratory analysis in order to preserve the information about the system from which the samples were taken. Pre-treatment procedures based on complexation of metal ions and moderate acidification of the samples are presented. The concentration of the stabilisation agent and the storage temperature were optimised. The most satisfactory results were obtained with 0.01 mol l(-1) phosphoric acid and a storage at 6 degrees C.     

Rapid separation of mercury,arsenic, thallium and chromium species

Radiochemical neutron activation analysis is the only method to determine the galactic cosmic ray (GCR) produced radionuclide⁵³Mn (T=3.8·10⁶) in small meteorite samples. A large number of such samples was analyzed using extremely thermalized neutrons of the DIDO reactor at the KFA Jülich. The detection limit of 10^–14 g/g was recently achieved in our laboratory through the improvement of pre- and postirradiation chemistry. The main purpose of our studies of meteorite finds from Antarctica and the Southwestern United States is to establish their exposure ages up to 12·10⁶ a by means of⁵³Mn. Especially in the case of Antarctic meteorites terrestrial ages up to several 10⁵ years have been observed by combining⁵³Mn and²⁶Al (T=7.2·10⁵ a) measurements.     

Factors affecting arsenic speciation in environmental samples: sample drying and storage

Arsenic is a ubiquitous element. Its toxicity, mobility, and bioaccumulation depend usually on its chemical form, and therefore, arsenic speciation is indispensable for the assessment of environmental risk and human hazard. Little is known about the effect of sample preparation procedures, such as drying and storage, on the resulting arsenic speciation. In this study, we investigated the influence of different drying methods and storage conditions on the arsenic speciation in mineral soils, organic soils, and plants. Drying soils and plants using different methods may change the concentrations of the total methanol–water (20%,?v/v) extractable arsenic, the proportion of organic arsenic and the ratio of arsenite-to-arsenate. Loss of methanol–water extractable arsenic compounds (up to 63%) was observed particularly in the samples rich in water. Following drying, the speciation of organic arsenic changed less than that of inorganic arsenic. Drying showed little influence on the total arsenic determination. None of the storage methods tested could preserve the arsenic speciation in organic soils and plants, although arsenic speciation after one-month storage varied less in freeze-dried samples than wet samples. Storage of the samples at low temperatures (2 or??20°C) had the largest impact on the samples rich in organic matters, leading to less arsenic being extractable by methanol–water. Both drying and storage of the soil and plant samples changed apparently the arsenic speciation. Therefore, we recommend conducting the arsenic speciation possibly with fresh and wet samples, so that the results of arsenic speciation may be more approaching the original states.     

The speciation of arsenic in seawater and marine species

Dissolved inorganic arsenic species were determined in natural waters and selected marine species. Prior to irradiation by NAA samples were preconcentrated and the As(III) and As(V) species separated by APCDT-chloroform extraction. Marine samples were digested by microwave heating. Interpretation of data was achieved by comparing the ratio of As(III)/As(V) in the samples and correlating it with the prevailing environmental conditions.     

Simultaneous determination of arsenic species and chromium(VI) by high-performance liquid chromatography-inductively coupled plasma-mass spectrometry

The simultaneous determination of As(III), As(V), monomethylarsenic acid (MMA), dimethylarsinic acid (DMA) and Cr(VI) in fresh water has been carried out by coupling an anion-exchange column to an inductively coupled plasma-mass spectrometer. Optimisation of chromatographic conditions led to baseline separation of signals from the five species in approximately 9 min using gradient elution. Detection limits were 0.02-0.05 microg As l(-1) and 5.5 microg Cr l(-1). Repeatability was 2-3% for arsenic species and higher, i.e., 8%, for Cr(VI) due to the higher background for this species. Arsenic species and hexavalent chromium stability in surface water samples was evaluated, and storage conditions were set to 1 day at 4 degrees C in polyethylene flasks (without acidification) in order to avoid As(III)-As(V) conversions. The method was applied to the analysis of surface water.     

Multielemental determination of arsenic, selenium and chromium(VI) species in water by high-performance liquid chromatography-inductively coupled plasma mass spectrometry

A new method for the simultaneous chromatographic separation and determination of arsenite, arsenate, mono-methylarsonic acid, dimethylarsinic acid, selenite, selenate and hexavalent chromium in water is presented. Speciation was achieved by on-line coupling of anion-exchange LC and inductively coupled plasma mass spectrometry (ICP-MS). Optimisation of the chromatographic conditions led to baseline separation of the seven species in 14 min using gradient elution with NH4NO3 20 mM, pH 8.7-NH4NO3 60 mM, pH 8.7 as mobile phase. Detection limits are in the range 40-60 ng l(-1) for arsenic species, around 130 ng l(-1) for Cr(VI), and higher for Se(IV) and Se(VI) (1.2 and 1.4 microg l(-1) respectively). The method showed good accuracy and repeatability, and no interference of chloride on 75As, 77Se or 53Cr was observed. The developed method was applied to the analysis of several environmental surface water samples.     

Simultaneous determination of arsenic, selenium, tin and mercury by non-dispersive atomic fluorescence spectrometry

A procedure is described for simultaneous determination of arsenic, selenium, tin and mercury in aqueous solution by non-dispersive atomic-fluorescence spectrometry. Radiofrequency-excited EDLs, 100% modulated in the kHz region, were used for atom excitation. Sodium tetrahydroborate was used as reductant and a hydrogen-argon miniflame as atomizer. In the optimized procedure, which uses 1 ml of sample, the limits of detection (three times the standard deviation of the blank) were 0.04, 0.08, 0.1 and 0.1 ng ml for arsenic, selenium, tin and mercury respectively. The linear dynamic range was greater than three decades for all analytes and the precision was better than 7% (typically 3%) for concentrations 1 ng ml . Results for mutual interference effects are reported. Copper, nickel, lead and cobalt interfered only with selenium (5 ng ml ), when present in at least 200-fold weight ratio to it. Using 5 ml of sample improved the limits of detection for selenium and arsenic (0.01 and 0.02 ng ml respectively), but at the expense of greater interference. Recovery from spiked natural water samples was better than 95% at the ng ml level, except for selenium in sea-water, when the recovery was only 85%. Determination of the four elements, including standard-addition and background measurements, requires about 10 min.     

Chemical speciation of chromium in sea water: Part 3. The determination of chromium species

A method for the determination of chromium(III), chromium(VI) and organicallybound chromium in sea water is reported. It is confirmed that sea water contains about 9 × 10^-9 M dissolved chromium. This is shown to be divided as ca. 15% inorganic Cr(III), ca. 25% inorganic Cr(VI) and ca. 60% organically-bound chromium. It is suggested that the inconsistency of earlier results on the dominant chromium species and its concentration in sea water is largely due to the fact that organically bound chromium species were not considered.     

Simultaneous determination of arsenic and selenium in biological samples by HG-AFS

A new method is proposed for simultaneous determination of traces of arsenic (As) and selenium (Se) in biological samples by hydride-generation double-channel non-dispersive atomic-fluorescence spectrometry (HG-AFS) from tartaric acid media. The effects of analytical conditions on fluorescence signal intensity were investigated and optimized. Interferences from coexisting ions were evaluated. Under optimum conditions linear response ranges above 20 g L^–1 for As and 32 g L^–1 for Se were obtained with detection limits of 0.13 and 0.12 g L^–1, respectively. The precision for elevenfold determination of As at the 4 g L^–1 level and of Se at the 8 g L^–1 level were 2.7 and 1.9% (RSD), respectively. Recoveries of 92.5–95.5% for As and 101.2–108.4% for Se were obtained for four biological samples and two certified biological reference materials. The proposed method has the advantages of simple operation, high sensitivity, and high efficiency; it was successfully used for simultaneous determination of As and Se in biological samples.     

Determination of arsenic,chromium, mercury,selenium and zinc in tropical marine fish by neutron activation

Determination of arsenic, chromium, mercury, selenium and zinc in several commonly consumed tropical marine fishes have been carried out by neutron activation followed by radiochemical separation to remove the interfering activities of sodium, potassium, bromine, and phosphorus, etc., in order to establish the baseline data and to measure the levels of contamination, if any. The results of this study positively indicate that the marine fishes of Bangladesh have concentrations much below the permissible levels for these toxic elements. A radiochemical scheme for the separation of seven trace elements in biological material is also presented in this paper.     

微波辅助萃取-液质联用技术测底泥砷、硒的化学形态

建立了用反相离子对色谱和电感耦合等离子体质谱的联用技术同时测定As（Ⅲ）、 As（Ⅴ）、 MMA、 DMA、 Se（Ⅳ）、 Se（Ⅵ）、 SeMet和SeCys的砷、硒化学形态分析方法. 分别从流动相pH值、离子对试剂的浓度、甲醇量和流速4个方面进行了分离测定条件的优化. 利用碰撞池技术（CCT）较好地解决了^40Ar^35Cl^＋复合离子对^75As的干扰, 并使^80Se的测定成为可能, 有效地提高了灵敏度. 将该方法应用于上海市苏州河底泥样品的微波辅助萃取液的形态分析中, 砷和硒的检出限分别达到0.4～1.3 和0.5～1.9 μg/L.     

Simultaneous determination of arsenic, selenium, and mercury by Ion exchange-vapor generation-inductively coupled plasma-mass spectrometry

Ion exchange (IE)-vapor generation (VG)-inductively coupled plasma (ICP)-mass spectrometry (MS) method has been employed to simultaneously determine trace amounts of As, Se, and Hg in acidic conditions. Before hydride generation, anion-exchange column was used to separate the analytes from the matrix. Effects of sample solution acidity, eluant conditions and concentrating time were investigated and optimized. The method sensitivity was improved, as well as the ability to refrain interference caused by chloride, mental ions and other hydride-forming elements compared with (CF)VG-ICP-MS method. Limits of detection (3σ, n = 10) for As, Se, and Hg were As, 0.0021 ng/ml; Se, 0.0022 ng/ml; Hg, 0.0007 ng/ml, respectively; and recovery values for interference experiments were between 95.6 and 100.3%. The developed method was applied to four standard biological and geological materials, and the determined results of As, Se, and Hg were consistent with the certified values.     

Stability studies of arsenic, selenium, antimony and tellurium species in water, urine, fish and soil extracts using HPLC/ICP-MS

The stability of arsenic, selenium, antimony and tellurium species in water and urine (NIST SRM 2670n) as well as in extracts of fish and soil certified reference materials (DORM-2 and NIST SRM 2710) has been investigated. Stability studies were carried out with As(III), As(V), arsenobetaine, monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), phenylarsonic acid (PAA), Se(IV), Se(VI), selenomethionine, Sb(III), Sb(V) and Te(VI). Speciation analysis was performed by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Best storage of aqueous mixtures of the examined species was achieved at 3 degrees C whereas at -20 degrees C species transformation especially of selenomethionine and Sb(V) took place and a new selenium species appeared within a period of 30 days. Losses and species transformations during extraction processes were investigated. Extraction of the spiked fish material with methanol/water led to partial conversion of Sb(III), Sb(V) and selenomethionine to two new antimony and one new selenium species. The other arsenic, selenium and tellurium species were almost quantitatively extracted. For soil spiked with MMA, PAA, Se(IV) and Sb(III), recoveries after extraction with water and sulfuric acid (0.01 mol/L) were below 20%.