Growth and properties of YAlO film synthesized by RF magnetron sputtering

YAlO films are synthesized on (1 0 0)-oriented Si substrates by RF magnetron sputtering method. Al₂O₃ wafer is used as a target material, and some small pieces of Y bulk material are put on the Al₂O₃ target to synthesize YAlO films. Y composition ratio is varied from 0 to 34%. Amorphous YAlO films are characterized. An electrical resistivity as high as 3.4 × 10¹⁴ Ω-cm is achieved for the YAlO film with Y composition ratio of 10%. The dielectric constant increases with increasing Y composition ratio, and the YAlO film with Y composition ratio of 34% has a dielectric constant of 10.2. The bandgap energy of the YAlO film is suggested to be wider than 6.5 eV. YAlO films with a surface roughness of 0.4-1.3 nm are obtained irrespective of the Y composition ratio.     

Magnetic properties of Nd–Fe–B film magnets prepared by RF sputtering

Highly oriented films of ∼6 μm in thickness consisting of the Nd₂Fe₁₄B compound phase were obtained by a three-dimensional sputtering method at room temperature and the subsequent crystallization by annealing. The c-axis orientation and coercivity of film samples were sensitive to the sputtering parameters and annealing conditions. The optimum temperature and time for annealing were 650 °C and 30 min to show the highest coercivity without any deterioration for the orientation of Nd₂Fe₁₄B grains, and furthermore the degree of c-axis orientation was increased by decreasing the Ar gas pressure or input power for sputtering. The resultant film magnets with good magnetic properties of B_r=∼1.06 T, H_C=∼371 kA/m, and (BH)_max=∼160 kJ/m³ were obtained under the optimized parameters for sputtering.     

磁控溅射Cl掺杂CdTe薄膜的孪晶结构与电学性质

CdTe用作薄膜太阳能电池吸收层需要经过氯处理才能得到高的光电转换效率,其中Cl原子的作用机理仍然没有完全被理解.实验发现Cl原子主要偏聚在CdTe晶界处,对晶界有钝化作用,而有第一性原理计算认为Cl原子掺入CdTe晶格能够引入浅能级提高光电转换效率.为了验证Cl原子掺杂是否对CdTe的光电转换效率有益,本文通过磁控溅射制备了100 ppm(ppm=1/1000000)Cl原子掺杂的CdTe(CdTe:Cl)薄膜并研究了薄膜的晶体结构与电学性质,同时对比了正常氯处理的无掺杂CdTe薄膜与CdTe:Cl薄膜之间的性质区别.实验发现Cl原子掺杂会在CdTe:Cl中形成大量仅由几个原子层构成的孪晶,电子和空穴在CdTe:Cl薄膜中没有分离的传导通道,而在氯处理后的CdTe薄膜中电子沿晶界传导,空穴沿晶粒内部传导.磁控溅射沉积的CdTe:Cl多晶薄膜属于高阻材料,退火前载流子迁移率很低,退火后载流子浓度降低到本征数量级,电阻率提高.CdTe:Cl薄膜电池效率远低于正常氯处理的无掺杂CdTe薄膜电池效率.磁控溅射制备的非平衡重掺杂CdTe:Cl多晶薄膜不适合用作薄膜太阳能电池的吸收层.     

GeC薄膜的射频磁控反应溅射制备及性质

用射频磁控反应溅射法在ZnS衬底上制备了GeC薄膜,研究了工艺参数对Ge靶溅射及GeC薄膜红外透射性能的影响.衬底温度较低时GeC薄膜中含有H,形成了CH₂,CH₃,Ge-CH₃等,使薄膜产生红外吸收;随衬底温度升高,薄膜红外吸收明显减小.靶基距、射频功率、Ar:CH₄气体流量比、总气压对靶面中毒及溅射影响较大,但对GeC薄膜红外吸收影响较小.靶面中毒严重时,所制备无氢GeC薄膜附着性能差,随靶中毒减弱薄膜附着性能变好.优化工艺后,在ZnS衬底上制备了附着性能良好的无氢GeC薄膜,其折射率约为1.78,薄膜中C的含量比Ge的大,二者主要形成了C—Ge键.所制备的GeC/GaP红外增透保护膜系对ZnS衬底有良好的增透效果. 关键词： GeC薄膜 红外透射光谱 射频磁控溅射 XPS     

Effects of hydrogen flow on properties of hydrogen doped ZnO thin films prepared by RF magnetron sputtering

The hydrogen doped ZnO (ZnO:H) thin films were deposited on quartz glass substrates by radio frequency magnetron sputtering. The doping characteristics of ZnO:H thin films with varied hydrogen flow ratio were investigated. At low hydrogen flow ratio (H₂/(H₂+Ar)≤0.02), the ZnO:H thin films exhibited dominant (002) peaks from X-ray diffraction and the lattice constants became smaller. The particles were mainly a columnar structure. The particles’ size became smaller, and the island-like structure appeared on the thin films surface. In addition, the low resistivity properties of ZnO:H thin films was ascribed to the increase of the carriers concentration and carriers mobility; When the hydrogen flow ratio was more than 0.02 (M≥0.02), two absorption bands at 1400–1800 cm^?1 and 3200–3900 cm^?1 were observed from the FT-IR spectra, which indicated that the ZnO:H thin films had typical Zn–H bonding, O–H bonding (hydroxyl), and Zn–H–O bonding (like-hydroxyl). The scanning electron microscope (SEM) results show that a large number of hydroxyl agglomeration formed an island-like structure on the thin films surface. The absorption peak at about 575 cm^?1 in the Raman spectra indicated that oxygen vacancies (V_O) defects were produced in the process of high hydrogen doping. In this condition, the low resistivity properties of ZnO:H thin films were mainly due to the increasing electron concentration resulted from V_O. Meanwhile, the Raman absorption peaks at approximately 98 cm^?1 and 436 cm^?1 became weaker, and the (002) XRD diffraction peak quenched and the lattice constants increased, which shows that the ZnO:H thin films no longer presented a typical ZnO hexagonal wurtzite structure. With the increasing of hydrogen flow ratio, the optical transmittance of ZnO:H thin films in the ultraviolet band show a clear Burstein–Moss shift effect, which further explained that electron concentration was increased due to the increasing V_O with high hydrogen doping concentration. Moreover, the optical reflectance of the thin films decreased, indicating the higher roughness of the films surface. It was noteworthy that etching effect of H plasma was obvious in the process of heavy hydrogen doping.     

Effect of buffer layer on VOx film fabrication by reactive RF sputtering

Vanadium oxide VO_x films were fabricated by RF magnetron sputtering on various metal buffer layers or silica glass substrates at a substrate temperature of 400 °C. V₂O₅ film was fabricated on a silica glass substrate, and VO₂ films were fabricated on V, W, Fe, Ni, Ti, and Pt metal buffer layers. The transition temperature of the sample on the V buffer layer was 68 °C and that on the W buffer layer was 53 °C. The VO₂ film was also fabricated on the V buffer layer by non-reactive sputtering using a V₂O₅ target at a substrate temperature of 400 °C.     

射频磁控溅射制备氧化钒薄膜的研究

氧化钒（VOx）薄膜是一种广泛应用于红外热成像探测的薄膜材料,研究VOx薄膜的制备工艺、获取高电阻温度系数（TCR）的VOx薄膜具有重要意义。以高纯金属钒作靶材,采用射频磁控溅射的方法在室温下制备了VOx薄膜。主要研究了氩氧流量比以及功率等工艺参数对薄膜TCR的影响,获得了较好的工艺参数。采用万用表和X射线光电子能谱仪（XPS）分别测试了不同条件下射频磁控溅射法制备的VOx薄膜的电阻特性和薄膜成分,测试结果表明,采用所获得的较好工艺参数制备的VOx薄膜TCR值大于1.8%。     

Thickness dependence of electrical properties of ITO film deposited on a plastic substrate by RF magnetron sputtering

Indium tin oxide (ITO) films with various thicknesses in range of 40-280 nm were prepared onto a plastic substrate (PMMA). Deposition was carried out with RF magnetron sputtering method and the substrate temperature was held at ∼70 °C, in lack of the thermal damage to the polymer substrate. Changes in microstructure and electrical properties of ITO films according to their thicknesses were investigated. It was found that amorphous layer with thickness of 80 nm was formed at the interface on the polymer substrate and polycrystalline ITO could be obtained above the thickness. Conductivity of ITO films was found to be strongly dependent on the crystallinity. Consequently, it is suggested that crystallinity of the deposited films should be enhanced at the initial stage of deposition and the thickness of amorphous region be reduced in order to prepare high quality ITO thin films on polymer substrates.     

GaP薄膜的射频磁控溅射沉积及其计算机模拟

以GaP为靶材采用射频磁控溅射法制备GaP红外光学薄膜，通过保持Ar Ⅰ 750nm发射光谱线强度不变获得了不同工艺参数，并对沉积过程进行了计算机模拟.功率较小、气压较大时，Ga和P的溅射率、输运效率及沉积到衬底时的能量均较小，Ga的溅射率及输运效率均大于P的，使薄膜沉积速率较低、薄膜中Ga的含量大于P的，GaP薄膜产生较大吸收.功率较大、气压较小时，Ga和P的溅射率、输运效率及沉积到衬底时的能量均增大，Ga的溅射率大于P的、但其输运效率小于P的，使GaP薄膜的沉积速率增大、薄膜中Ga与P的含量接近化学计量比，GaP薄膜的吸收降低，因此有利于制备厚度较大的GaP薄膜. 关键词： GaP 薄膜 射频磁控溅射 计算机模拟     

Microstructure of microwave dielectricthin films by RF magnetron sputtering

The article describes the microstructure and morphological properties of microwave dielectric ceramic thin films. These thin films were successfully prepared on SiO₂ (1 1 0) single-crystal substrates by radio frequency magnetron-sputtering system. The microstructure and morphology of the thin films were characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, and transmission electron microscopy. The results show that the main phase is Ba_0.5Sr_0.5Nb₂O₆,which has a tetragonal perovskite structure, a long strip pattern, and uniform crystal-grain size of about 2-3 μm in length when annealed under 1150 °C for 30 min in an O₂ atmosphere. These thin films are of excellent crystallization quality, with a polycrystalline and dense structure.     

溅射方法干式处理超导加速腔表面的研究与分析

详细研究了利用超高真空氩离子清洗技术发展的一种超导铌腔表面的“干式”处理方法,从微观和宏观角度分析了溅射处理对铌的表面特性和对超导腔性能的影响.与传统的“湿式”处理方法(化学抛光BCP和电抛光EP)相比,干式处理方法具有结构简单、容易控制、没有污染等优点,是一种很有潜力的超导腔处理方法,可以提高超导腔的性能. 关键词： 超导加速腔 溅射 形貌分析 残留电阻比RRR     

Gadolinia-doped ceria films deposited by RF reactive magnetron sputtering

Gadolinia-doped ceria (GDC) films were prepared by RF reactive magnetron sputtering from a Gd-10 at.% Ce alloy target in reactive O₂/Ar gas mixtures and annealed at 700 °C for 2 h. Material characteristics and chemical compositions of GDC films were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). Electrical behaviors were measured by AC impedance in the range of 500–700 °C at OCV for air condition. The microstructure of GDC films was found to be an assembly of columnar crystallites with a cubic fluorite structure. The total conductivity of 700 °C-annealed GDC (GDC-1) with the obtained composition of (Ce_0.911Gd_0.089)O_1.938 was higher than that of bulk yttria-stabilized zirconia (YSZ), but smaller than bulk GDC. The governing mechanism of conduction of sputtered-GDC electrolyte films was mainly governed by a grain boundary process, which resulted in a blocking effect and the lower conductivity of thin films than that of bulk GDC samples. Our results suggested that sputtered-GDC films with a comparable conductivity can be used as solid electrolyte layers for a solid oxide fuel cell (SOFC) system as compared to the well-known YSZ.     

Refractive index variation of amorphous Ta2O5 film fabricated by ion beam sputtering with RF bias power

Ta₂O₅ film was fabricated by ion beam sputtering with RF bias applied to the substrate. The refractive index in the visible range of the film can be controlled to vary linearly with the RF bias power while low absorption is maintained.     

射频溅射制备的BST薄膜介电击穿研究

采用射频溅射制备BST薄膜，研究了薄膜的介电击穿特性.实验表明，在电压增大到传统击穿电压(电流密度出现瞬时增大时的电压)之前，薄膜性能已被破坏，发现在传统击穿状态之前存在另一个新状态——初始击穿状态.通过测试各状态的J-V(电流密度-电压)、J-T(电流密度-温度)特性分析其导电机理，建立了薄膜结构、漏电性能随电场强度增大而变化的模型.最后提出了确定实际意义上击穿电压的方法. 关键词： BST薄膜 介电击穿 漏电流     

Properties of amorphous carbon nitride prepared by RF reactive sputtering

The local microstructure and optical and electrical properties were investigated of amorphous carbon nitride (a-CN) films deposited by reactive radio-frequency (RF) sputtering. Two series prepared in nitrogen or in a nitrogen and argon mixture were studied. The optical properties were investigated by transmittance/reflectance and photothermal deflection spectroscopies. Combined infrared measurements and Raman scattering spectroscopies were used to investigate the microstructure of a-CN films in terms of nitrogen incorporation within the films and C sp ² content. These experiments were completed by dark electrical conductivity measurements performed in coplanar configuration in the temperature range 50–450?K. The films exhibit semiconductor behaviour and the temperature dependence suggests two types of conduction. An increase in nitrogen incorporation induces an increase with clustering of sp ² phase replacing C=C olefinic groups with aromatic groups.     

等离子体发射光谱诊断用于射频磁控溅射GaP薄膜的工艺参数优化

以GaP为靶材、Ar为工作气体,采用射频磁控溅射法制备了厚层GaP膜.对沉积过程中的辉光放电等离子体进行了发射光谱诊断,发现只有ArⅠ发射谱线.研究了工艺参数对发射谱线强度的影响规律,并在此基础上通过同时改变射频功率、Ar气流量及工作气压,使ArⅠ发射谱线强度保持相同.发现通过增大射频功率、减小工作气压而保持ArⅠ发射谱线强度不变可以提高GaP膜的沉积速率,并使GaP膜的沉积工艺参数得到优化.在优化后的工艺参数下制备出了符合化学计量比、红外透过性能好的厚层GaP膜. 关键词： GaP薄膜 射频磁控溅射 等离子体发射光谱 红外透射     

Material and detector of PZT doped Bi

From phase diagram, this paper discusses the selecting rules of PZT for a pyroelectric material and the doping Bi material that Zr/Ti is 94/6 is particularly reported. The experiment process and the points for attention are given. The two kinds of the infrared detector using this material, the one being with-substrate and the other without-substrate, are produced and discussed. The characters of the material and the detectors are given in the paper.     

Boron doped ZnO thin films fabricated by RF-magnetron sputtering

By using the radio frequency-magnetron sputtering (RF-MS) method, both pure ZnO and boron doped ZnO (ZnO:B) thin films were deposited on glass substrates at ambient temperature and then annealed at 450 °C for 2 h in air. It is found that both ZnO and ZnO:B thin films have wurtzite structure of ZnO with (0 0 2) preferred orientation and high average optical transmission (≥80%). Compared with the resistivity of 6.3 × 10² Ω cm for ZnO film, both as-deposited and annealed ZnO:B films exhibit much lower resistivity of 9.2 × 10⁻³ Ω cm and 7.5 × 10⁻³ Ω cm, respectively, due to increase in the carrier concentration. Furthermore, the optical band gaps of 3.38 eV and 3.42 eV for as-deposited and annealed ZnO:B films are broader than that of 3.35 eV for ZnO film. The first-principles calculations show that in ZnO:B thin films not only the band gap becomes narrower but also the Fermi level shifts up into the conduction band with respect to the pure ZnO film. These are consistent with their lower resistivities and suggest that in the process of annealing some substituted B in the lattice change into interstitial B because of its smaller ion radius and this transformation widens the optical band gap of ZnO:B thin film.     

直流三极溅射法制备CuInS2 薄膜

采用直流三极溅射装置制备获得了CuInS₂薄膜, 其中溅射靶采用一定面积比的[Cu]/[In]混合靶,反应气体采用CS₂气体. 本文中主要研究了0.02 Pa分压反应气体条件下不同面积比的[Cu]/[In]混合靶和沉积基板温度对CuInS₂薄膜结构和成分的影响, 其中CuInS₂薄膜制备所用时间为2 h生长的厚度为1—2 μm. 通过对CuInS₂薄膜的EPMA, X射线衍射测试分析表明, 最佳的CuInS₂薄膜可在面积比[Cu]/[In]混合靶为1.4:1和可控温度(150, 250和350 ℃)的条件下制备获得, 并且其结构被确认为黄铜矿结构. 通过实验结果计算出CuInS₂薄膜层有约为8.9%的C杂质含量.