Influence of glucose on the structural and optical properties of ZnO thin films prepared by sol-gel method

In this work, ZnO thin films were prepared by sol-gel method on glass substrates followed by calcinations at 500 °C for an hour. The effect of glucose on the structure and optical properties of the films was studied. The structural characteristics of the samples were analyzed by X-ray diffractometer (XRD) and atomic force microscope (AFM). The optical properties were studied by a UV-visible spectrophotometer. The results show that some of the prepared ZnO thin films have a high preferential oriented c-axis orientation with compact hexagonal wurtzite structure due to a proper amount of glucose introducing. After introducing the glucose additive in ZnO colloids, the intensity of (002) peak, the transmittance, and the optical band gap of the ZnO thin films increases because of the enhanced ZnO crystallization. On the contrary, the absorbance, the film thickness, and the surface root-mean-square (RMS) roughness of the ZnO thin films decreases. The glucose additive could not only improve the surface RMS roughness and microstructure of ZnO thin films, but also enhance the transmittance and the energy band gap more easily.     

Effect of aging time of ZnO sol on the structural and optical properties of ZnO thin films prepared by sol-gel method

In this work, ZnO thin films were prepared by sol-gel method and the effect of aging time of ZnO sol on the structural and optical properties of the films was studied. The structural characteristics of the samples were analyzed by an atomic force microscope and an X-ray diffractometer. The optical properties were studied by a UV-vis spectrophotometer and a fluorophotometer. The results show that the ZnO thin film prepared by the as-synthesized ZnO sol had relatively poor crystalline quality, low optical transmittance in the visible range and relatively weak ultraviolet emission performance. After the as-synthesized ZnO sol was aged for 24 h, the degree of the preferred crystal orientation along the c-axis of the ZnO thin film prepared by this aged sol was improved. At the same time, this film had a very smooth surface with uniform grains and both its visible range transmittance and ultraviolet emission intensity were obviously increased. These results suggest that appropriate aging of ZnO sol is very important for the improvement of structural and optical quality of ZnO thin films derived from sol-gel method.     

Morphological and optical properties of silicon thin films by PLD

Silicon thin films have been prepared on sapphire substrates by pulsed laser deposition (PLD) technique. The films were deposited in vacuum from a silicon target at a base pressure of 10⁻⁶ mbar in the temperature range from 400 to 800 °C. A Q-switched Nd:YAG laser (1064 nm, 5 ns duration, 10 Hz) at a constant energy density of 2 J × cm⁻² has been used. The influence of the substrate temperature on the structural, morphological and optical properties of the Si thin films was investigated.Spectral ellipsometry and atomic force microscopy (AFM) were used to study the thickness and the surface roughness of the deposited films. Surface roughness values measured by AFM and ellipsometry show the same tendency of increasing roughness with increased deposition temperature.     

Effect of substrate temperature on the structural and optical properties of ZnO and Al-doped ZnO thin films prepared by dc magnetron sputtering

ZnO and Al-doped ZnO(ZAO) thin films have been prepared on glass substrates by direct current (dc) magnetron sputtering from 99.99% pure Zn metallic and ZnO:3 wt%Al₂O₃ ceramic targets, the effects of substrate temperature on the crystallization behavior and optical properties of the films have been studied. It shows that the surface morphologies of ZAO films exhibit difference from that of ZnO films, while their preferential crystalline growth orientation revealed by X-ray diffraction remains always the (0 0 2). The optical transmittance and photoluminescence (PL) spectra of both ZnO and ZAO films are obviously influenced by the substrate temperature. All films exhibit a transmittance higher than 86% in the visible region, while the optical transmittance of ZAO films is slightly smaller than that of ZnO films. More significantly, Al-doping leads to a larger optical band gap (E_g) of the films. It is found from the PL measurement that near-band-edge (NBE) emission and deep-level (DL) emission are observed in pure ZnO thin films. However, when Al was doped into thin films, the DL emission of the thin films is depressed. As the substrate temperature increases, the peak of NBE emission has a blueshift to region of higher photon energy, which shows a trend similar to the E_g in optical transmittance measurement.     

Effect of K-doping on structural and optical properties of ZnO thin films

In this work, K-doped ZnO thin films were prepared by a sol–gel method on Si(111) and glass substrates. The effect of different K-doping concentrations on structural and optical properties of the ZnO thin films was studied. The results showed that the 1 at.% K-doped ZnO thin film had the best crystallization quality and the strongest ultraviolet emission ability. When the concentration of K was above 1 at.%, the crystallization quality and ultraviolet emission ability dropped. For the K-doped ZnO thin films, there was not only ultraviolet emission, but also a blue emission signal in their photoluminescent spectra. The blue emission might be connected with K impurity or/and the intrinsic defects (Zn interstitial and Zn vacancy) of the ZnO thin films.     

A comparative study on structural and optical properties of ZnO and Al-doped ZnO thin films obtained by ultrasonic spray method using different solvents

Transparent conducting ZnO and Al doped ZnO thin films were deposited on glass substrate by ultrasonic spray method. The thin films with concentration of 0.1 M were deposited at 350 °C with 2 min of deposition time. The effects of ethanol and methanol solution before and after doping on the structural, optical and electrical properties were examined. The DRX analyses indicated that ZnO films have nanocrystalline nature and hexagonal wurtzite structure with (1 0 0) and (0 0 2) preferential orientation corresponding to ZnO films resulting from methanol and ethanol solution, respectively. The crystallinity of the thin films improved with methanol solution after doping to (0 0 2) oriented. All films exhibit an average optical transparency about 90%, in the visible range. The band gaps values of ZnO thin films are increased after doping from 3.10 to 3.26 eV and 3.27 to 3.30 eV upon Al doping obtained by ethanol and methanol solution, respectively. The electrical conductivity increase from 7.5 to 15.2 (Ω cm)⁻¹ of undoped to Al doped ZnO thin films prepared by using ethanol solution. However, for the methanol solution; the electrical conductivity of the film is stabilized after doping.     

Influence of annealing temperature on structural, optical and magnetic properties of Mn-doped ZnO thin films prepared by sol-gel method

Thin films of Zn_1−xMn_xO (x=0.01) diluted magnetic semiconductor were prepared on Si (1 0 0) substrates by the sol-gel method. The influence of annealing temperature on the structural, optical and magnetic properties was studied by X-ray diffraction (XRD), atom force microscopy (AFM), photoluminescence (PL) and SQUID magnetometer (MPMS, Quantum Design). The XRD spectrum shows that all the films are single crystalline with (0 0 2) preferential orientation along c-axis, indicating there are not any secondary phases. The atomic force microscopy images show the surfaces morphologies change greatly with an increase in annealing temperature. PL spectra reveal that the films marginally shift the near band-edge (NBE) position due to stress. The magnetic measurements of the films using SQUID clearly indicate the room temperature ferromagnetic behavior, and the Curie temperature of the samples is above room temperature. X-ray photoelectron spectroscopy (XPS) patterns suggest that Mn²⁺ ions were successfully incorporated into the lattice position of Zn²⁺ ions in ZnO host. It is also found that the post-annealing treatment can affect the ferromagnetic behavior of the films effectively.     

Influence of annealing temperature on structural and optical properties of ZnO: In thin films prepared by ultrasonic spray technique

Transparent conducting indium doped zinc oxide was deposited on glass substrate by ultrasonic spray method. The In doped ZnO samples with indium concentration of 3 wt.% were deposited at 300, 350 and 400 °C with 2 min of deposition time. The effects of substrate temperature and annealing temperature on the structural, electrical and optical properties were examined. The DRX analyses indicated that In doped ZnO films have polycrystalline nature and hexagonal wurtzite structure with (0 0 2) preferential orientation and the maximum average crystallite size of ZnO: In before and annealed at 500 °C were 45.78 and 55.47 nm at a substrate temperature of 350 °C. The crystallinity of the thin films increased by increasing the substrate temperature up 350 °C, the crystallinity improved after annealing temperature at 500 °C. The film annealed at 500 °C and deposited at 350 °C show lower absorption within the visible wavelength region. The band gap energy increased from E_g = 3.25 to 3.36 eV for without annealing and annealed films at 500 °C, respectively, indicating that the increase in the transition tail width. This is due to the increase in the electrical conductivity of the films after annealing temperature.     

Influence of substrate temperature and Cobalt concentration on structural and optical properties of ZnO thin films prepared by Ultrasonic spray technique

Pure and Cobalt doped zinc oxide were deposited on glass substrate by Ultrasonic spray method. Zinc acetate dehydrate, Cobalt chloride, 4-methoxyethanol and monoethanolamine were used as a starting materials, dopant source, solvent and stabilizer, respectively. The ZnO samples and ZnO:Co with Cobalt concentration of 2 wt.% were deposited at 300, 350 and 400 °C. The effects of substrate temperature and presence of Co as doping element on the structural, electrical and optical properties were examined. Both pure and Co doped ZnO samples are (0 0 2) preferentially oriented. The X-ray diffraction results indicate that the samples have polycrystalline nature and hexagonal wurtzite structure with the maximum average crystallite size of ZnO and ZnO:Co were 33.28 and 55.46 nm. An increase in the substrate temperature and presence doping the crystallinity of the thin films increased. The optical transmittance spectra showed transmittance higher than 80% within the visible wavelength region. The band gap energy of the thin films increased after doping from 3.25 to 3.36 eV at 350 °C.     

The structural and optical properties of ZnO/Si thin films by RTA treatments

ZnO/Si thin films were prepared by rf magnetron sputtering method and some of the samples were treated by rapid thermal annealing (RTA) process at different temperatures ranging from 400 to 800 °C. The effects of RTA treatment on the structural properties were studied by using X-ray diffraction and atomic force microscopy while optical properties were studied by the photoluminescence measurements. It is observed that the ZnO film annealed at 600 °C reveals the strongest UV emission intensity and narrowest full width at half maximum among the temperature ranges studied. The enhanced UV emission from the film annealed at 600 °C is attributed to the improved crystalline quality of ZnO film due to the effective relaxation of residual compressive stress and achieving maximum grain size.     

Effect of post-thermal annealing on the structural and optical properties of ZnO thin films prepared from a polymer precursor

ZnO thin films were synthesised by a new method which uses polyvinyl alcohol (PVA) as the polymer precursor. The films are annealed at different temperatures and for different annealing times. The structural parameters, like grain size, lattice constants, optical band gap, and Urbach energy, depend on the annealing temperature and time. All the films possess tensile strain, which relaxes as the annealing temperature and time increase. The photoluminescence (PL) spectra contain only ultraviolet (UV) peaks at low temperature, but as the annealing temperature and time increase, we observe peaks at the blue and green regions with a variation in the intensities of these peaks with annealing temperature and time.     

Effect of post-thermal and optical properties annealing on the structural of ZnO thin films prepared from a polymer precursor

ZnO thin films were synthesised by a new method which uses polyvinyl alcohol （PVA） as the polymer precursor. The films are annealed at different temperatures and for different annealing times. The structural parameters, like grain size, lattice constants, optical band gap, and Urbach energy, depend on the annealing temperature and time. All the films possess tensile strain, which relaxes as the annealing temperature and time increase. The photoluminescence （PL） spectra contain only ultraviolet （UV） peaks at low temperature, but as the annealing temperature and time increase, we observe peaks at the blue and green regions with a variation in the intensities of these peaks with annealing temperature and time.     

Effect of post thermal annealing on the structural and optical properties of ZnO thin films prepared from polymer precursor

ZnO thin films were synthesised by a new method which uses polyvinyl alcohol (PVA) as polymer precursor. The films are annealed at different temperatures and for different annealing times. The structural parameters, like grain size, lattice constants, optical band gap, and Urbach energy, depend on the annealing temperature and annealing time. All the films possess tensile strain which relaxes as the annealing temperature and the annealing time increases. The photoluminescence (PL) spectra contain only ultraviolet (UV) peaks at low temperature, but as the annealing temperature and time increase we observe peaks at blue and green regions with variation of the intensities of these peaks with annealing temperature and annealing time.     

Microstructures, optical and electrical properties of In-doped ZnO thin films prepared by sol-gel method

ZnO and indium-doped ZnO (I_xZO) thin films were prepared on silica-glass substrates by the sol-gel method. The thin films were crystallized at 600 °C and 700 °C for 1 h in 6.9 × 10⁻¹ Torr under pure O₂ atmosphere. The analyzed results were compared to investigate the structural characteristics and optical properties. The surface morphology of the I_xZO films was different from that of the ZnO films, and showed a thin overlay structure. In addition, the crystallization of I_xZO film was depleted at higher crystallized temperatures. From XRD analysis, the ZnO and I_xZO thin films possessed hexagonal structures. Notably, micro-In₂O₃ phases were observed in the I_xZO thin films using EDS. Both of In₂O₃ phases and the crystallization mechanism not only improved the peeling of structure, but also improved the electrical conductivity of I_xZO thin films. For the PL spectrum, the optical property of the I_xZO film was raised at a higher crystallization temperature. Although the In₂O₃ phases reduced the structural defects of I_xZO thin film, the optical effect of the residual In³⁺ was not enhanced completely at higher crystallized temperatures.     

Structural and optical properties of ZnO thin films prepared by sol-gel method with different thickness

In this work, ZnO thin films with different thickness were prepared by sol-gel method on glass substrates and the structural and optical properties of these films were studied by X-ray diffractometer, atomic force microscope, UV-visible spectrophotometer, ellipsometer and fluorophotometer, respectively. The structural analyses show that all the samples have a wurtzite structure and are preferentially oriented along the c-axis perpendicular to the substrate surface. The growth process of highly c-axis oriented ZnO thin films derived from sol-gel method is a self-template process. With the increase of film thickness, the structural disorder decreases and the crystalline quality of the films is gradually improved. A transition of crystal growth mode from vertical growth to lateral growth is observed and the transition point is found between 270 and 360 nm thickness. The optical analyses show that with the increase of film thickness, both the refractive index and ultraviolet emission intensity are improved. However, the transmittance in the visible range is hardly influenced by the film thickness, and the averages are all above 80%.     

Structural and optical properties of YSZ thin films grown by PLD technique

We report on the structural and optical properties of yttria stabilized zirconia (YSZ) thin films grown by pulsed laser deposition (PLD) technique and in situ crystallized at different substrate temperatures (T_s = 400 °C, 500 °C and 600 °C). Yttria-stabilized zirconia target of ∼1 in. diameter (∼95% density) was fabricated by solid state reaction method for thin film deposition by PLD. The YSZ thin films were grown on an optically polished quartz substrates and the deposition time was 30 min for all the films. XRD analysis shows cubic crystalline phase of YSZ films with preferred orientation along 〈1 1 1〉. The surface roughness was determined by AFM for the films deposited at different substrate temperatures. The nano-sized surface roughness is found to increase with the increase of deposition temperatures. For the optical analysis, a UV-vis-NIR spectrophotometer was used and the optical band gap of ∼5.7 eV was calculated from transmittance curves.     

Correlation between the structural and optical properties of Co doped ZnO thin films prepared at different film thickness

Cobalt doped zinc oxide (ZnO:Co) thin films were deposited on glass substrates by ultrasonic spray technique decomposition of Zinc acetate dihydrate and cobalt acetate tetrahydrate in an ethanol solution with film thickness. All films are polycrystalline with a hexagonal wurtzite-type structure with a preferential orientation according to the direction (0 0 2), with the maximum crystallite size was found of 59.42 nm at 569 nm. The average transmittance of all films is about 65–95% measured by UV–vis analyzer. The band gap energy increased from 3.08 to 3.32 eV with increasing the film thickness from 192 to 569 nm. The increase of the electrical conductivity with increases in the film thickness to maximum value of 9.27 (Ω cm)⁻¹ can be explained by the increase in carrier concentration and displacement of the electrons of the films. The correlation between the band gap and crystal structure suggests that the band gap energy of Co doped ZnO is influenced by the crystallite size and the mean strain.     

Dependence of film thickness on the structural and optical properties of ZnO thin films

ZnO thin films are prepared on glass substrates by pulsed filtered cathodic vacuum arc deposition (PFCVAD) at room temperature. Optical parameters such as optical transmittance, reflectance, band tail, dielectric coefficient, refractive index, energy band gap have been studied, discussed and correlated to the changes with film thickness. Kramers-Kronig and dispersion relations were employed to determine the complex refractive index and dielectric constants using reflection data in the ultraviolet-visible-near infrared regions. Films with optical transmittance above 90% in the visible range were prepared at pressure of 6.5 × 10⁻⁴ Torr. XRD analysis revealed that all films had a strong ZnO (0 0 2) peak, indicating c-axis orientation. The crystal grain size increased from 14.97 nm to 22.53 nm as the film thickness increased from 139 nm to 427 nm, however no significant change was observed in interplanar distance and crystal lattice constant. Optical energy gap decreased from 3.21 eV to 3.19 eV with increasing the thickness. The transmission in UV region decreased with the increase of film thickness. The refractive index, Urbach tail and real part of complex dielectric constant decreased as the film thickness increased. Oscillator energy of as-deposited films increased from 3.49 eV to 4.78 eV as the thickness increased.     

Characterization of ZnO:Ga and ZnO:N films prepared by PLD

The thin films of zinc oxide have been produced by the pulse laser deposition method at various levels of gallium and nitrogen doping. To obtain the n-type films we used gallium doping with concentration of gallium from zero up to 5 at %. The dependence of photoluminescence of the epitaxial ZnO:Ga films on the concentration of gallium doping has been studied. An optimum range of the n-type ZnO films doping with gallium has been determined to obtain highly effective films from the viewpoint of realizing p-n transitions. This range, on the one hand, defines the maximal PL amplitude and, on the other hand, specifies the minimal specific resistance that corresponds to an interval of 0.125–1.000 at % Ga. To produce the p-type ZnO:(Ga, N) films, the ZnO targets with the content of GaN from zero up to 2 at % were used. N₂O was used as a buffer gas. A difference is observed in the positions of the peaks of the emission lines of the photoluminescence spectra for the ZnO films, doped with gallium (Ga) and co-doped with gallium and nitrogen (N).     

Structural and optical properties of La-doped BaSnO3 thin films grown by PLD

In this study the structural and optical properties of lanthanum-doped BaSnO₃ powder samples and thin films deposited on fused silica were investigaed using laser ablation. Under an oxygen pressure of 5×10⁻⁴ mbar, phase pure BaSnO₃ films with a lattice constant of 0.417 nm and grain size of 21 nm were prepared at 630 °C. The band gap of BaSnO3 powder sample and thin films was calculated to be 3.36 eV and 3.67 eV, respectively. There was a progressive increase in conductivity for thin films of BaSnO₃ doped with 0~7 at% of La. The highest conductivity, 9 Scm⁻¹, was obtained for 7 at% La-doped BaSnO₃. Carrier concentration, obtained from Burstein-Moss (B-M) shift, nearly matches the measured values except for 3 at% and 10 at% La-doped BaSnO₃ thin films.