A facile thermal evaporation route for large-area synthesis of tin oxide nanowires: Characterizations and their use for liquid petroleum gas sensor

In this paper, a very simple procedure was presented for the reproducible synthesis of large-area SnO₂ nanowires (NWs) on a silicon substrate by evaporating Sn powders at temperatures of 700, 750, and 800 °C. As-obtained SnO₂ NWs were characterized by field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Raman spectroscopy. They revealed that the morphology of the NWs is affected by growth temperature and the SnO₂ NWs are single-crystalline tetragonal. The band gap of the NWs is in the range of 4.2–4.3 eV as determined from UV/visible absorption. The NWs show stable photoluminescence with an emission peak centered at around 620 nm at room-temperature. The sensors fabricated from the SnO₂ NWs synthesized at 700 °C exhibited good response to LPG (liquefied petroleum gas) at an operating temperature of 400 °C.     

Synthesis,characterization and photoluminescence of ZnO:Cd rosette-like nanostructures using solution process

Well crystalline undoped and Cd-doped ZnO rosette-like structures were successfully synthesized at low temperature (80 °C) via solution process technique during 30 min. Zinc nitrate, cadmium nitrate, sodium hydroxide and hexamine were used as starting materials. The morphology and microstructure were determined by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX) and photoluminescence (PL) spectroscopy. X-ray diffraction indicated that the structure has a single phase with wurtzite structure. FESEM indicated that rosette like structures have been formed. This rosette consists of nanorods with length 210 and 460 nm and diameter 50 and 74 nm for undoped and Cd doped ZnO, respectively. HRTEM showed a decrease in the lattice parameter after the Cd doping. EDX showed that the amount of Cd incorporated into ZnO is 6.4 wt.%. Photoluminescence measurements taken on both doped and undoped samples showed that, in the Cd-doped ZnO nanostructures, the band-edge UV emission is blue shifted and the broad green emission intensity decreased.     

Synthesis and surface modification of ZnO:Cu nanoparticles by silica and PMMA

ZnO nanoparticles doped with Cu were synthesized by solid state reaction using different precursor routes and varying growth environment. Average crystallite size varied from 40 to 100 nm depending upon synthesis temperature, lower temperature favouring smaller particle size. Scanning electron microscope (SEM) images showed that particles synthesized at 250 °C were in the shape of nanorods but those synthesized at 900 °C had spherical shape. Luminescence emission showed marked dependence on the growth conditions varying from ultraviolet (UV) emission to green emission. For making the luminescent nanoparticles bio-compatible, a bioinorganic interface on ZnO:Cu nanoparticles was created by coating them with inert silica. Surface modification of ZnO:Cu was also done with lipophilic polymethylmethacrylate (PMMA). ZnO:Cu nanoparticles showed hexagonal wurtzite structure and the coating of silica was confirmed with the presence of two extra peaks due to silica in the XRD spectra. Thermogravimetric analysis (TGA) and FTIR spectroscopy indicated that PMMA molecules were adsorbed on the surface of ZnO:Cu nanoparticles. SEM images revealed that PMMA adsorption improved the dispersibilty of ZnO:Cu nanoparticles.     

XPS investigation of vacuum annealed vertically aligned ultralong ZnO nanowires

The surface properties of vertically aligned ZnO nanowires grown by chemical vapour deposition on GaN using a gold layer as a catalyst are investigated by X-ray Photoelectron Spectroscopy as a function of annealing temperature in ultra high vacuum (UHV). The nanowires are 8.5 μm long and 60 nm wide. 87% of the surface carbon content was removed after annealing at 500 °C in UHV. Analysis of the gold intensity suggests diffusion into the nanowires after annealing at 600 °C. Annealing at 300 °C removes surface water contamination and induces a 0.2 eV upward band bending, indicating that adsorbed water molecules act as surface electron donors. The contaminants re-adsorbed after 10 days in UHV and the surface band bending caused by the water removal was reversed. The UHV experiment also affected the nanowires arrangement causing them to bunch together. These results have clear implications for gas sensing applications with ZnO NWs.     

Synthesis of nanocrystalline ZnO nanobelts via pyrolytic decomposition of zinc acetate nanobelts and their gas sensing behavior

The pyrolytic decomposition of layered basic zinc acetate (LBZA) nanobelts (NBs) into nanocrystalline ZnO NBs is investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL). We also report on the gas sensing response of the resulting ZnO nanomaterial to CO. The LBZA NBs are grown at 65 °C in an aqueous solution of zinc acetate dihydrate. AFM and SEM results show as-grown products possess the characteristic layered structure of the LBZA crystals. XRD and XPS results show that annealing as-grown products at 210 °C in air causes a transformation from zinc acetate to nanocrystalline ZnO NBs via thermal decomposition. The ZnO crystalline domain size increases with temperature from 9.2 nm at 200 °C to 94 nm at 1000 °C, as measured from XRD. SEM shows evidence of sintering at 600 °C. The thickness of the NBs, determined via AFM, ranges from 10 to 50 nm and remains approximately constant with annealing temperature. XPS confirmed the chemical transformation from zinc acetate to ZnO and showed a significant remaining zinc hydroxide component for the ZnO NBs consistent with published results. PL measurements at room temperature show a blue shift in peak emission as the nanobelts change from LBZA to ZnO at 200 °C. Above this transition temperature, the ZnO nanobelts possess strong band edge emission at 390 nm and little broad band emission in the visible region. The AFM and SEM images reveal that the crystallites within the nanobelts orientate in rows along the long axis during annealing. This structure provides a high surface area to volume ratio of aligned nanoparticles which is beneficial for gas sensing applications. Gas sensors fabricated from 400 °C annealed nanobelts showed a response of 1.62 when exposed to 200 ppm of CO in dry air at 400 °C, as defined by the ratio of resistance before and during exposure. This indicates that ZnO nanostructures obtained by thermal decomposition of LBZA NBs could provide a cost effective route to high sensitivity gas sensors.     

Structural and photoluminescence investigation on the hot-wire assisted plasma enhanced chemical vapor deposition growth silicon nanowires

High density of silicon nanowires (SiNWs) were synthesized by a hot-wire assisted plasma enhanced chemical vapor deposition technique. The structural and optical properties of the as-grown SiNWs prepared at different rf power of 40 and 80 W were analyzed in this study. The SiNWs prepared at rf power of 40 W exhibited highly crystalline structure with a high crystal volume fraction, X_C of ～82% and are surrounded by a thin layer of SiO_x. The NWs show high absorption in the high energy region (E>1.8 eV) and strong photoluminescence at 1.73 to 2.05 eV (red–orange region) with a weak shoulder at 1.65 to 1.73 eV (near IR region). An increase in rf power to 80 W reduced the X_C to ～65% and led to the formation of nanocrystalline Si structures with a crystallite size of <4 nm within the SiNWs. These NWs are covered by a mixture of uncatalyzed amorphous Si layer. The SiNWs prepared at 80 W exhibited a high optical absorption ability above 99% in the broadband range between 220 and ～1500 nm and red emission between 1.65 and 1.95 eV. The interesting light absorption and photoluminescence properties from both SiNWs are discussed in the text.     

Effects of morphology on photocatalytic performance of Zinc oxide nanostructures synthesized by rapid microwave irradiation methods

In this study, two different chemical solution methods were used to synthesize Zinc oxide nanostructures via a simple and fast microwave assisted method. Afterwards, the photocatalytic performances of the produced ZnO powders were investigated using methylene blue (MB) photodegradation with UV lamp irradiation. The obtained ZnO nanostructures showed spherical and flower-like morphologies. The average crystallite size of the flower-like and spherical nanostructures were determined to be about 55 nm and 28 nm, respectively. X-ray diffraction (XRD), scanning electronic microscopy (SEM), Brunauer–Emmett–Teller (BET), room temperature photoluminescence (RT-PL) and UV–vis analysis were used for characterization of the synthesized ZnO powders. Using BET N₂-adsorption technique, the specific surface area of the flower-like and spherical ZnO nanostructures were found to be 22.9 m²/gr and 98 m²/gr, respectively. Both morphologies show similar band gap values. Finally, our results depict that the efficiency of photocatalytic performance in the Zinc oxide nanostructures with spherical morphology is greater than that found in the flower-like Zinc oxide nanostructures as well as bulk ZnO.     

Nanocasting synthesis and gas-sensing behavior of hematite nanowires

The dispersed and uniform hematite nanowires (α-Fe₂O₃ NWs) with the different diameter were synthesized using SBA-15 as hard templates by the nanocasting method, and the diameter of α-Fe₂O₃ NWs was about 4, 6 and 8 nm, respectively. The BET surface area of α-Fe₂O₃ NWs changed a little, while the bandgap decreased from 2.07, 2.03 to 1.91 eV with the increasing diameter according to quantum size effect. Compared all samples, the sensitivity of α-Fe₂O₃ NWs based gas-sensors increased from 10.64 to 11.43 with the bandgap and BET surface area α-Fe₂O₃ NWs in 100 ppm ethanol at 300 °C, and the response–recovery time was also improved for the good crystallinity. It's concluded that the surface area greatly affected the gas-sensing performance of α-Fe₂O₃ NWs based sensors, while the bandgap and crystallinity also influenced the gas-sensing behavior to some extent. The α-Fe₂O₃ NWs based gas-sensors exhibited the high sensitivity, fast response–recovery and good selectivity to ethanol.     

Magneto-optical properties of α-Fe2O3@ZnO nanocomposites prepared by the high energy ball-milling technique

Magnetic–fluorescent nanocomposites (NCs) with 10 wt% of α-Fe₂O₃ in ZnO have been prepared by the high energy ball-milling. The crystallite sizes of α-Fe₂O₃ and ZnO in the NCs are found to vary from 65 nm to 20 nm and 47 nm to 15 nm respectively as milling time is increased from 2 to 30 h. XRD analysis confirms presence of α-Fe₂O₃ and ZnO in pure form in all the NCs. UV–vis study of the NCs shows a continuous blue-shift of the absorption peak and a steady increase of band gap of ZnO with increasing milling duration that are assigned to decreasing particle size of ZnO in the NCs. Photoluminescence (PL) spectra of the NCs reveal three weak emission bands in the visible region at 421, 445 and 485 nm along with the strong near band edge emission at 391 nm. These weak emission bands are attributed to different defect – related energy levels e.g. Zn-vacancy, Zn interstitial and oxygen vacancy. Dc and ac magnetization measurements show presence of weakly interacting superparamagnetic (SPM) α-Fe₂O₃ particles in the NCs. ⁵⁷Fe-Mössbauer study confirms presence of SPM hematite in the sample milled for 30 h. Positron annihilation lifetime measurements indicate presence of cation vacancies in ZnO nanostructures confirming results of PL studies.     

Low-temperature synthesis of Zn2SiO4:Mn green photoluminescence phosphor

Zn₂SiO₄:Mn green phosphor having comparable photoluminescence (PL) efficiency with commercial phosphor has been synthesized at 1000 °C using solid state reactions involving ZnO, silicic acid and manganese acetate. The water of crystallization attached to SiO₂ in silicic acid whose dissociation at 1000 °C seem to promote the sintering efficiency of Zn₂SiO₄:Mn. Incremental ZnO addition and re-firing at 1000 °C promote the diffusion rate of ZnO and SiO₂. The formation of a single crystalline phase of willemite structure in the samples was confirmed by powder XRD measurements. The phosphor exhibit an intense excitation band centered around 275 nm and a relatively weak excitation centered around 380 nm while the broad band green emission peaks at 524 nm. Other parameters studied include PL spectra, grain morphology, ZnO/SiO₂ molar ratio, Mn concentration, co-dopant/flux and the effect of chemical forms of Mn dopant as well as silica on the PL efficiency.     

Ultrasonic-assisted degradation of phenazopyridine with a combination of Sm-doped ZnO nanoparticles and inorganic oxidants

Pure and samarium doped ZnO nanoparticles were synthesized by a sonochemical method and characterized by TEM, SEM, EDX, XRD, Pl, and DRS techniques. The average crystallite size of pure and Sm-doped ZnO nanoparticles was about 20 nm. The sonocatalytic activity of pure and Sm-doped ZnO nanoparticles was considered toward degradation of phenazopyridine as a model organic contaminant. The Sm-doped ZnO nanoparticles with Sm concentration of 0.4 mol% indicated a higher sonocatalytic activity (59%) than the pure ZnO (51%) and other Sm-doped ZnO nanoparticles. It was believed that Sm³⁺ ion with optimal concentration (0.4 mol%) can act as superficial trapping for electrons in the conduction band of ZnO and delayed the recombination of charge carriers. The influence of the nature and concentration of various oxidants, including periodate, hydrogen peroxide, peroxymonosulfate, and peroxydisulfate on the sonocatalytic activity of Sm-doped ZnO nanoparticles was studied. The influence of the oxidants concentration (0.2–1.4 g L⁻¹) on the degradation rate was established by the 3D response surface and the 2D contour plots. The results demonstrated that the utilizing of oxidants in combination with Sm-doped ZnO resulting in rapid removal of contaminant, which can be referable to a dual role of oxidants; (i) scavenging the generated electrons in the conduction band of ZnO and (ii) creating highly reactive radical species under ultrasonic irradiation. It was found that the Sm-doped ZnO and periodate combination is the most efficient catalytic system under ultrasonic irradiation.     

Structural and optical properties of Co-doped ZnO nanocrystallites prepared by a one-step solution route

Zinc oxide (ZnO) nanocrystallites with different Co-doping levels were successfully synthesized by a simple one-step solution route at low temperature (95 °C) in this study. The structure and morphology of the samples thus obtained were characterized by XRD, EDS, XPS and FESEM. Results show that cobalt ions, in the oxidation state of Co²⁺, replace Zn²⁺ ions in the ZnO lattice without changing its wurtzite structure. The dopant content varies from 0.59% to 5.39%, based on Co-doping levels. The pure ZnO particles exhibit well-defined 3D flower-like morphology with an average size of 550 nm, while the particles obtained after Co-doping are mostly cauliflower-like nanoclusters with an average size of 120 nm. Both the flower-like pure ZnO and the cauliflower-like Co:ZnO nanoclusters are composed of densely arrayed nanorods. The optical properties of the ZnO nanocrystallites following Co-doping were also investigated by UV–Visible absorption and Photoluminescence spectra. Our results indicate that Co-doping can change the energy-band structure and effectively adjust the luminescence properties of ZnO nanocrystallites.     

Influence of Al-doped ZnO and Ga-doped ZnO substrates on third harmonic generation of gold nanoparticles

Principal role of substrate types on the nonlinear optical properties of Au NP was investigated. Third harmonic generation (THG) studies were carried out for Au NP deposited on the Al-doped ZnO (AuNP/AZO) and Ga-doped ZnO (AuNP/GZO) substrates at fundamental wavelength of 20 ns Er:glass laser (generating at 1540 nm wavelength) during photostimulation by the 532 nm 15 ns laser pulses. Sizes of Au NP were 5 nm, 10 nm, 20 nm, and 30 nm. The output signal was registered at 513 nm. The photoinduced power density was increased from 0 up to 800 MW/cm². So in our work we explore the role of the substrate on the optically stimulated non-linear optical properties during simultaneous photo stimulation near the inter-band transition. The results were studied depending on the type of substrate and the sizes of the deposited nanoparticles. The analysis was done within a framework of interaction between the photoinduced light and SPR wavelengths. Control of the photoinduced temperature was done.     

Ultrasound-assisted synthesis of poly(MMA–co–BA)/ZnO nanocomposites with enhanced physical properties

The present study reports synthesis and characterization of poly(MMA–co–BA)/ZnO nanocomposites using ultrasound-assisted in-situ emulsion polymerization. Methyl methacrylate (MMA) was copolymerized with butyl acrylate (BA), for enhanced ductility of copolymer matrix, in presence of nanoscale ZnO particles. Ultrasound generated strong micro-turbulence in reaction mixture, which resulted in higher encapsulation and uniform dispersion of ZnO (in native form – without surface modification) in polymer matrix, as compared to mechanical stirring. The nanocomposites were characterized for physical properties and structural morphology using standard techniques such as XRD, FTIR, particle size analysis, UV–Visible spectroscopy, electrical conductivity, TGA, DSC, FE-SEM and TEM. Copolymerization of MMA and BA (in presence of ZnO) followed second order kinetics. Thermal stability (T_10% = 324.9 °C) and glass transition temperature (T_g = 67.8 °C) of poly(MMA-co-BA)/ZnO nanocomposites showed significant enhancement (35.1 °C for 1 wt% ZnO and 15.7 °C for 4 wt% ZnO, respectively), as compared to pristine poly(MMA–co–BA). poly(MMA–co–BA)/ZnO (5 wt%) nanocomposites possessed the highest electrical conductivity of 0.192 μS/cm and peak UV absorptivity of 0.55 at 372 nm. Solution rheological study of nanocomposites revealed enhancement in viscosity with increasing ZnO loading. Maximum viscosity of 0.01 Pa-s was obtained for 5 wt% ZnO loading.     

Comparative study on the effects of different annealing conditions on the surface morphology,crystallinity, and optical properties of ZnO micro/nanoparticle-based discs

The effects of annealing parameters on the surface morphology, crystallinity, and optical properties of ZnO disc were investigated. Variations in the annealing temperatures and gas flow rates were found to have a profound impact; grain growth was enhanced even at the low annealing temperature of only 400 °C. SEM and AFM revealed smooth and uniform grain growth after annealing treatment, especially at 800 °C. A unique secondary growth of ZnO nanoparticles and multilayer grain growth that have not been reported elsewhere were also observed. The annealing treatment was also found to improve grain crystallinity as illustrated by the lowering of intrinsic compressive stress based on the XRD lattice constant and FWHM data. The PL spectra of the M-Disc showed a huge band edge emission at 371–376 nm. In contrast, the N-Disc exhibited a dominant and broad visible PL emission in the green band with peaks at 519–533 nm. These peaks were attributed to a very high concentration of structural defects (oxygen vacancies and zinc/oxygen interstitials). The annealing conditions had a significant effect on the properties of ZnO. Increased percentage of oxygen in the O/Ar from 50% to 100% did not change the M-Disc spectra. However, the XRD pattern of the N-Disc revealed that the (0 0 2) peak intensity decreased, the position of the (1 0 1) peak slightly shifted toward a higher angle, and the FWHM of the (1 0 1) peak improved. The experimental results showed that thermal annealing could enhance the different properties of ZnO discs.     

Emission of Cu-related complexes in ZnO:Cu nanocrystals

Photoluminescence (PL), its temperature dependence, scanning electronic microscopy (SEM) and X ray diffraction (XRD) have been applied for the comparative study of varying the emission, morphology and crystal structure of ZnO and ZnO:Cu nanocrystals (NCs) versus technological routines, as well as the dependence of ZnO:Cu NC parameters on the Cu concentration. A set of ZnO and ZnO Cu NCs was prepared by the electrochemical (anodization) method at a permanent voltage and different etching durations with follows thermal annealing at 400 °C for 2 h in ambient air. The size of ZnO NCs decreases from 300 nm×540 nm down to 200 nm×320 nm with etching duration increasing. XRD study has confirmed that thermal annealing stimulates the ZnO oxidation and crystallization with the formation of wurtzite ZnO crystal lattice. XRD method has been used for monitoring the lattice parameters and for confirming the Cu doping of ZnO Cu NCs. In ZnO Cu NCs four defect related PL bands are detected with the PL peaks at 1.95–2.00 eV (A), 2.15-2.23  eV (B), 2.43–2.50 eV (C) and 2.61–2.69 eV (D). Highest PL intensities of orange, yellow and green emissions have been obtained in ZnO Cu NCs with the Cu concentration of 2.28 at%. At Cu concentration increasing (≥2.28 at%) the PL intensities of the bands A, B, C decrease and the new PL band peaked at 2.61–2.69 eV at 10 K appears in the PL spectrum. The variation of PL intensities for all PL bands versus temperature has been studied and the corresponding activation energies of PL thermal decay have been estimated. The type of Cu-related complexes is discussed using the correlation between the PL spectrum transformation and the variation of XRD parameters in ZnO Cu NCs.     

Photocatalytic degradation of ciprofloxacin drug in water using ZnO nanoparticles

We report the synthesis of nanostructure ZnO semiconductor with ～2.1 nm diameter using a chemical precipitation method. The resulting nanoparticles were characterized by X-ray diffraction analysis (XRD), Fourier-transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The optical properties were investigated by UV–vis and fluorescence techniques. The absorption spectra exhibit a sharp absorption edge at ～334 nm corresponding to band gap of ～3.7 eV. The fluorescence spectra displayed a near-band-edge ultraviolet excitonic emission at ～410 nm and a green emission peak at ～525 nm, due to a transition of a photo-generated electron from the conduction band to a deeply trapped hole. The photocatalytic activity of the prepared ZnO nanoparticles has been investigated for the degradation of ciprofloxacin drug under UV light irradiation in aqueous solutions of different pH values. The results showed that the photocatalytic degradation process is effective at pH 7 and 10, but it is rather slow at pH 4. Higher degradation efficiency (～50%) of the drug was observed at pH 10 after 60 min. Photodegradation of the drug follows a pseudo-first-order kinetics.     

The influence of Au thickness on the structural,optical and electrical properties of ZnO/Au/ZnO multilayer films

Transparent and conductive ZnO/Au/ZnO (ZAZ) multilayer films were deposited on glass substrates by magnetron sputtering without intentional substrate heating. The thickness of Au interlayer was set at 1, 2 and 3 nm.The observed structural, optical and electrical properties were dependent on the thickness of the Au interlayer. For all of the ZAZ films, the diffraction peaks in the XRD pattern were identified as the (002) and (103) planes of a ZnO films and the (111) plane of an Au interlayer. The ZAZ films with a 2 nm thick Au interlayer showed a higher figure of merit than the other ZAZ films prepared in this study, and they also demonstrated the relatively high work function of 5.13 eV.From these results, we concluded that a ZAZ film with a 2 nm thick Au interlayer is an alternative candidate for use as a transparent electrode in OLEDs and various flat panel displays.     

Strong violet emission from zinc oxide dumbbell-like microrods and nanowires

ZnO of different morphologies with controlled size and aspect ratio (l/d) such as dumbbell-like microrods, thick nanowires and thin nanowires were prepared by a hydrothermal method. Possible mechanisms for the formation of ZnO crystals with the different morphologies were discussed. Strong violet photoluminescence bands at～413 nm (3.0 eV) without band edge emission were observed from the dumbbell-like ZnO microrods and thick nanowires. Correspondingly, the thin nanowires showed a weak shoulder UV photoluminescence band at～390 nm. Such result indicates that the photoluminescence properties could be improved by the morphologies or aspect ratio (l/d) and the potential fabrication violet-light-emitting devices.     

Studies on growth morphology,UV absorbance and luminescence properties of sulphur doped ZnO nanopowders synthesized by the application of ultrasound with varying input power

Sulphur doped ZnO nanopowders have been prepared by sonochemical method in continuous (CS) and pulsed (PS) modes. Precipitation time was found to vary with input power of applied ultrasound. X-ray diffraction studies show the formation hexagonal wurtzite phase of nano ZnO but variation in size, strain and lattice parameters was observed in the samples synthesized through CS and PS modes with different input power. Surface morphology of the samples changed significantly with input power of the pulse as observed from scanning electron microscopic results. Well defined and c-axis oriented nanorods and multipodes were observed with power setting of 187.5 W whereas in all other cases no definite morphology was observed. UV absorption studies show higher value of absorbance for ZnO:S. Further, the absorption band becomes sharp for the samples prepared with power setting of 225 W. PL spectra show several bands due to different transitions in the region of 400–780 nm which have been explained in the light of excitonic and defect induced transitions in ZnO.