A preliminary study on a new LiBOB/acetamide solid phase transition electrolyte

New solid electrolytes containing acetamide and lithium bioxalato borate (LiBOB) with different molar ratios have been investigated. Their melting points (T_m) are around 42 °C. The ionic conductivities and activation energies vary drastically below and above T_m, indicating a typical feature of phase transition electrolyte. The ionic conductivity of the LiBOB/acetamide electrolyte with a molar ratio of 1:8 is 5 × 10^? 8 S cm^? 1 at 25 °C but increases to 4 × 10^? 3 S cm^? 1 at 60 °C. It was found that anode materials, such as graphite and Li₄Ti₅O₁₂, could not discharge and charge properly in this electrolyte at 60 °C due to the difficulty in forming a stable passivating layer on the anodes. However, a Li/LiFePO₄ cell with this electrolyte can be charged properly after heating to 60 °C, but cannot be charged at room temperature. Although the LiBOB/acetamide electrolytes are not suitable for Li-ion batteries due to poor electrode compatibility, the current results indicate that a solid electrolyte with a slightly higher phase transition temperature than room temperature may find potential application in stationary battery for energy storage where the electrolyte is at high conductive liquid state at elevated temperature and low conductive solid state at low temperature. The interaction between acetamide and LiBOB in the electrolyte is also studied by Raman and FTIR spectroscopy.     

Polymorphic phase transition and thermal stability in squaric acid (H2C4O4)

Phase transformations in squaric acid (H₂C₄O₄) have been investigated by thermogravimetry and differential scanning calorimetry with different heating rates β. The mass loss in TG apparently begins at onset temperatures T_di=245±5 °C (β=5 °C min^?1), 262±5 °C (β=10 °C min^?1), and 275±5 °C (β=20 °C min^?1). A polymorphic phase transition was recognized as a weak endothermic peak in DSC around 101 °C (T_c⁺). Further heating with β=10 °C min^?1 in DSC revealed deviation of the baseline around 310 °C (T_i), and a large unusual exothermic peak around 355 °C (T_p), which are interpreted as an onset and a peak temperature of thermal decomposition, respectively. The activation energy of the thermal decomposition was obtained by employing relevant models. Thermal decomposition was recognized as a carbonization process, resulting in amorphous carbon.     

Dielectric,ferroelectric and piezoelectric properties of (1−x)[K0.5Na0.5NbO3]−x[LiSbO3] ceramics

Lead-free (1?x)[K_0.5Na_0.5NbO₃]?x[LiSbO₃] (x=0, 0.04, 0.05 and 0.06)/(KNN-LS) ceramics were prepared by conventional solid-state reaction route (CSSR). For dense morphology pure KNN ceramic was sintered at 1120 °C and LS modified KNN ceramics were sintered at 1080 °C for 4 h, respectively. The structural study at room temperature (RT) revealed the transformation of pure orthorhombic to tetragonal structure with the increase in LS content in KNN-LS ceramics. Temperature dependent dielectric study confirmed the increase of diffuse phase transition nature with the increase in LS content in KNN-LS ceramics. The presence of orthorhombic to tetragonal (T_O?T) polymorphic phase transition temperature (PPT) ～43 °C confirmed the presence of two ferroelectric (orthorhombic and tetragonal) phases in 0.95KNN-0.05LS ceramics at RT. 0.95KNN-0.05LS ceramics showed better ferroelectric and piezoelectric properties i.e., remnant polarization (P_r)～18.7 μC/cm², coercive field (E_c)～11.8 kV/cm, piezoelectric coefficient (d₃₃)～215 pC/N, coupling coefficient (k_p)～0.415 and remnant strain ～0.07% were obtained.     

Effect of processing temperature on the superconducting properties of acetone doped MgB2 tapes

Correlation of phase formation, critical transition temperature T_c, microstructure, and critical current density J_c with sintering temperature has been studied for acetone doped MgB₂/Fe tapes. Sintering was performed at 600–850 °C for 1 h in a flowing Ar atmosphere. High boron substitution by carbon was obtained with increasing the sintering temperature; however, the acetone doped samples synthesized at 800 °C contain large size MgB₂ grains and more MgO impurities. Incomplete reaction for the acetone doped samples heated at 600 °C result in bad intergrain connectivity. At 4.2 K, the best J_c value was achieved in the acetone doped sample sintered at 700 °C, which reached 24,000 A/cm² at 10 T and 10,000 A/cm² at 12 T, respectively. Our results indicate that the small grain size and less impurity were also important for the improvement of J_c–B properties besides the substitutions of B by C.     

Experimental investigation of flame spreading over pure methane hydrate in a laminar boundary layer

Flame spreading over pure methane hydrate in a laminar boundary layer is investigated experimentally. The free stream velocity (U_∞) was set constant at 0.4 m/s and the surface temperature of the hydrate at the ignition (T_s) was varied between ?10 and ?80 °C. Hydrate particle sizes were smaller than 0.5 mm. Two types of flame spreading were observed; “low speed flame spreading” and “high speed flame spreading”. The low speed flame spreading was observed at low temperature conditions (T_s = ?80 to ?60 °C) and temperatures in which anomalous self-preservation took place (T_s = ?30 to ?10 °C). In this case, the heat transfer from the leading flame edge to the hydrate surface plays a key role for flame spreading. The high speed flame spreading was observed when T_s = ?50 and ?40 °C. At these temperatures, the dissociation of hydrate took place and the methane gas was released from the hydrate to form a thin mixed layer of methane and air with a high concentration gradient over the hydrate. The leading flame edge spread in this premixed gas at a spread speed much higher than laminar burning velocity, mainly due to the effect of burnt gas expansion.     

Ce0.8Sm0.2O1.9 synthesis for solid oxide fuel cell electrolyte by ultrasound assisted co-precipitation method

In this study, the synthesis of Ce_0.8Sm_0.2O_1.9 (SDC) solid electrolyte by the ultrasound assisted co-precipitation method was accomplished to explore the effects of ultrasound power, ultrasound pulse ratio and probe type upon the ionic conductivity of SDC as well as the lattice parameter, the microstructure and the density. Fine powders of uniform crystallite sizes (average 11.70 ± 0.62 nm) were obtained, needing lower sintering temperature. The SDC powders were successfully sintered to a relative density of over 95% at 1200 °C (5 °C min^?1) for 6 h. The micrograph of SDC pellets showed non-agglomerated and well-developed grains with average size of about 200 nm. X-ray diffraction analysis showed that the lattice parameter increased with increasing acoustic intensity and reached a maximum for the 14.94 W cm^?2. Further, a linear relationship was detected between the lattice parameter and the ionic conductivity, inspiring a dopant like effect of US on the electrolyte properties. The highest ionic conductivity as σ_800°C = 3.07 × 10^?2 S cm^?1 with an activation energy E_a = 0.871 kJ mol^?1 was obtained with pulsed ultrasound for an acoustic intensity of 14.94 W cm^?2, using 19 mm probe and 8:2 pulse ratio.     

Characterization of doped La0.7A0.3Cr0.5Mn0.5O3 − δ (A = Ca,Sr, Ba) electrodes for solid oxide fuel cells

Doped lanthanum manganese chromite based perovskite, La_0.7A_0.3Cr_0.5Mn_0.5O_3 ? δ (LACM, A = Ca, Sr, Ba), on yttria-stabilized zirconia (YSZ) electrolyte is investigated as potential electrode materials for solid oxide fuel cells (SOFCs). The electrical conductivity and electrochemical activity of LACM depend on the A-site dopant. The best electrochemical activity is obtained on the La_0.7Ca_0.3Cr_0.5Mn_0.5O_3 ? δ/YSZ (LCCM/YSZ) composite electrodes. The conductivity of LCCM is 29.9 S cm^? 1 at 800 °C in air, and the electrode polarization resistance (R_E) of the LCCM/YSZ composite cathode for the O₂ reduction reaction is 0.5 Ω cm² at 900 °C. The effect of Gd-doped ceria (GDC) impregnation on the LCCM cathode polarization resistances is also studied. GDC impregnation significantly enhances the electrochemical activity of the LCCM cathode. In the case of the 6.02 mg cm^? 2 GDC-impregnated LCCM cathode, R_E is 0.4 Ω cm² at 800 °C, ~ 60 times smaller than 24.4 Ω cm² measured on a LCCM cathode without the GDC impregnation. Finally the electrochemical activities of the doped lanthanum manganese chromites for the H₂ oxidation reaction are also investigated.     

Structural and magnetic properties of thin epitaxial Fe films on (1 1 0) GaAs prepared by metalorganic chemical vapor deposition

Iron films have been grown on (1 1 0) GaAs substrates by atmospheric pressure metalorganic chemical vapor deposition at substrate temperatures (T_s) between 135°C and 400°C. X-ray diffraction (XRD) analysis showed that the Fe films grown at T_s between 200°C and 330°C were single crystals. Amorphous films were observed at T_s below 200°C and it was not possible to deposit films at T_s above 330°C. The full-width at half-maximum of the rocking curves showed that crystalline qualities were improved at T_s above 270°C. Single crystalline Fe films grown at different substrate temperature showed different structural behaviors in XRD measurements. Iron films grown at T_s between 200°C and 300°C showed bulk α-Fe like behavior regardless of film thickness (100–6400 Å). Meanwhile, Fe films grown at 330°C (144 and 300 Å) showed a biaxially compressed strain between substrate and epilayer, resulting in an expanded inter-planar spacing along the growth direction. Magnetization measurements showed that Fe films (>200 Å) grown at 280°C and 330°C were ferromagnetic with the in-plane easy axis along the [1 1 0] direction. For the thinner Fe films (⩽200 Å) regardless of growth temperature, square loops along the [1 0 0] easy axis were very weak and broad.     

Improved stability of La0.5Sr0.5FeO3 by Ta-doping for oxygen separation membrane application

(La,Sr)FeO₃ mixed conducting perovskites are considered as interesting candidates for oxygen separation membranes but they suffer from limited structural stability in a large oxygen partial pressure (pO₂) gradient, because of their propensity for chemical expansion. Partial substitution of Fe with more stable elements tends to improve the stability while penalizing the electronic and ionic conductivities.In this study, we investigate the effect of 10% Ta substitution on the oxygen transport properties and stability of La_0.5Sr_0.5FeO₃. For this purpose, the material was evaluated as a membrane in a CPOX reactor. The oxygen permeation through a ~ 3 cm² pellet sample was first measured under air/Ar gradient in the temperature range of 800 to 1000 °C. The measured flux was 0.1 µmol cm^? 2 s^? 1 at 900 °C, which was a factor of 2 lower than for the Ta-free material. Methane was then introduced into the system and reacted in a catalytic bed with oxygen that has permeated through the membrane to form syngas (H₂, CO). As a result, the oxygen flux increased by a factor of 9, reaching 0.9 µmol cm^? 2 s^? 1 at 900 °C. The reactor was operated at 1000 °C for another 1000 h. During this time, the oxygen permeation flux decayed by ca. 4%/1000 h.The test was stopped after more than 2000 h of operation and the membrane analyzed by electron microscopy.     

Field-assisted sustainable O− ion emission from fluorine-substituted 12CaO·7Al2O3 with improved thermal stability

We examined the electric field-assisted thermionic emission of atomic oxygen radical anion (O^?) in a vacuum from fluorine-substituted derivatives of 12CaO·7Al₂O₃ (C12A7) with a composition of (12 ? x)CaO·7Al₂O₃·xCaF₂ (0 ≤ x ≤ 0.8). Unsubstituted C12A7 easily decomposed into 5CaO?3Al₂O₃ (C5A3) and 3CaO?Al₂O₃ (C3A) above 830 °C during the emission experiment in a vacuum. The decomposition temperature range became narrower as the amount of F^? ion substitution increased, e.g. the sample with x = 0.4 kept a single phase after the emission experiment at 900 °C. The emitted anionic species from the x = 0.4 sample were dominated by O^? ions (～ 92%) together with a small amount of O₂^? ions (～ 4%) and F^? ions (～ 4%). The absence of an O₂ gas supply to the opposite side of the emission surface led to a nearly steady co-emission of O^? ions and electrons with a ratio of < 1/1. The O₂ gas supply markedly enhanced the O^? ion emission, and suppressed the electron emission. A sustainable and high-purity O^? ion emission with a current density of 11 nA cm^? 2 was achieved at 830 °C with the supply of 40 Pa O₂ gas. The similarity in these emission features to the unsubstituted C12A7, together with the improved thermal stability demonstrates that the F^? ion-substituted C12A7 is a promising material for higher intensity O^? ion emission at higher temperatures.     

Structure and piezoelectric properties of BiFeO3 and Bi0.92Dy0.08FeO3 multiferroics at high temperature

Multiferroic BiFeO₃ and Bi_0.92Dy_0.08FeO₃ ceramics were prepared to study their crystal structures and piezoelectric properties. BiFeO₃ exhibits rhombohedral phase below 810 °C. Although Bi_0.92Dy_0.08FeO₃ ceramic also shows rhombohedral phase at room temperature, it allows the coexistence of rhombohedral phase and orthorhombic phase at 460–650 °C. Both samples have maximum polarizations of >21 μC/cm² and piezoelectric d₃₃ values of ～37 pC/N at room temperature. Their polarized slices show the dielectric anomalies and impedance anomalies because of vibrating resonances below 500 °C, and the thickness vibration electromechanical coupling factor is ～0.6 and ～0.4 for BiFeO₃ and Bi_0.92Dy_0.08FeO₃, respectively. The vibrating resonances confirm piezoelectric responses. Furthermore, samples' impedance and resistance decrease fast with temperature increasing, which screens piezoelectric response above 550 °C.     

Electret properties of ethylene–propylene random co-polymer

Thermally stimulated current (TSC) spectra were examined for ethylene–propylene (EP) random co-polymer at different charging voltages V_p with positive and negative polarities. Observed TSC spectra showed two well-separated TSC bands, B_L and B_H, which respectively appeared in the temperature regions below and above 100 °C. Observed V_p dependence of B_L was quite different from that of typical polypropylene homo-polymer: As V_p increased, B_L band grew keeping its peak position same at 65 °C, and the band shape unchanged, as if the traps responsible for the B_L band are a single set of traps with the same trap depth and capture cross section. The trap depth of B_L was about 1.9 eV and 1.7 eV for positively charged EP and talc-containing EP samples, respectively. EP samples also showed unique TSC bands above 100 °C: one is a narrow TSC band peaked at 120 °C and the other is an unusual TSC band which was non-vanishing even at 165 °C just before destruction of samples by their melting. Consequently, the utmost stable charge density in EP co-polymer above 100 °C was found to be 3.5 × 10^?4 C/m² and 6.0 × 10 ^?4 C/m² for positively and negatively charged samples, respectively. These equivalent surface charge densities are much larger than those of usual polypropylene homo-polymer.     

Sintering kinetics and oxide ion conduction in Sr-doped apatite-type lanthanum silicates,La9Sr1Si6O26.5

These last past years, a major interest has been devoted to decrease the working temperature of solid oxide fuel cells (SOFCs) down to about 700 °C.Apatite materials (La_10 ? xSr_xSi₆O_27?x/2) are attractive candidates for solid electrolytes, with a high ionic conductivity at these intermediate temperatures. An apatite powder (x = 1) with a 0.75 µm mean particle size, produced by solid state reaction, was tape cast to obtain green sheets with a thickness of about 260 µm.On one hand, the densification mechanism of the apatite ceramic during the intermediate solid state sintering has been approached. It appeared from the kinetical tests performed under isothermal conditions between 1250 and 1550 °C, that densification could be controlled by the diffusion at grain boundaries of the rare-earth element, La, with an activation energy of 470 kJ/mol.On the other hand, conductivity measurements were performed on apatite samples sintered at 1400 and 1500 °C. The ionic conductivity was mainly sensitive to the presence of secondary phases at 1400 °C. The ionic conductivity of the apatite sintered at 1500 °C (mean grain size = 3.9 µm) is equal to 1.2 × 10^? 2 S/cm at 700 °C.     

Luminescence and defect studies of YAlO3:Dy3+, Sm3+ single crystals exposed to 100 MeV Si7+ ion beam

Ionoluminescence (IL) and photoluminescence (PL) spectra for different rare earth ions (Sm³⁺ and Dy³⁺) activated YAlO₃ single crystals have been induced with 100 MeV Si⁷⁺ ions with fluence of 7.81×10¹² ions cm^?2. Prominent IL and PL emission peaks in the range 550–725 nm in Sm³⁺ and 482–574 nm in Dy³⁺ were recorded. Variation of IL intensity in Dy³⁺ doped YAlO₃ single crystals was studied in the fluence range 7.81×10¹²–11.71×10¹² ions cm^?2. IL intensity is found to be high in lower ion fluences and it decreases with increase in ion fluence due to thermal quenching as a result of an increase in the sample temperature caused by ion beam irradiation. Thermoluminescence (TL) spectra were recorded for fluence of 5.2×10¹² ions cm^?2 on pure and doped crystals at a warming rate of 5 °C s^?1 at room temperature. Pure crystals show two glow peaks at 232 (Tg₁) and 328 °C (Tg₂). However, in Sm³⁺ doped crystals three glow peaks at 278 (Tg₁), 332 (Tg₂) and 384 °C (Tg₃) and two glow peaks at 278 (Tg₁) and 331 °C (Tg₂) in Dy³⁺ was recorded. The kinetic parameters (E, b s) were estimated using glow peak shape method. The decay of IL intensity was explained by excitation spike model.     

Thermo,Iono and photoluminescence properties of 100 MeV Si7+ ions bombarded CaSiO3:Eu3+ nanophosphor

This paper reports on the thermo (TL), iono (IL) and photoluminescence (PL) properties of nanocrystalline CaSiO₃:Eu³⁺ (1–5 mol %) bombarded with 100 MeV Si⁷⁺ ions for the first time. The effect of different dopant concentrations and influence of ion fluence has been discussed. The characteristic emission peaks ⁵D₀→⁷F_J (J=0, 1, 2, 3, 4) of Eu³⁺ ions was recorded in both PL (1×10¹¹–1×10¹³ ions cm^?2) and IL (4.16×10¹²–6.77×10¹² ions cm^?2) spectra. It is observed that PL intensity increases with ion fluence, whereas in IL the peaks intensity increases up to fluence 5.20×10¹² ions cm^?2, then it decreases. A well resolved TL glow peak at ～304 °C was recorded in all the ion bombarded samples at a warming rate of 5 °C s^?1. The TL intensity is found to be maximum at 5 mol% Eu³⁺ concentration. Further, TL intensity increases sub linearly with shifting of glow peak towards lower temperature with ion fluence.     

Synthesis and characterization of (Pr0.75Sr0.25)1 − xCr0.5Mn0.5O3 − δ as anode for SOFCs

The complex perovskite (Pr_0.75Sr_0.25)_1 − xCr_0.5Mn_0.5O_3 − δ (PSCM) has been prepared and studied as possible anode material for high-temperature solid oxide fuel cells (SOFCs). PSCM exhibits GdFeO₃-type structure and is both physically and chemically compatible with the conventional YSZ electrolyte. The reduction of PSCM resulted in structural change from orthorhombic Pbnm to cubic Pm-3m. Selected area electron diffraction (SAED) analysis on the reduced phases indicated the presence of a √2 × √2 × 2 superlattice. The total conductivity values of ∼ 75% dense Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ at 900 °C in air and 5% H₂/Ar are 9.6 and 0.14 S cm^− 1 respectively. The conductivity of PSCM drops with decreasing Po₂ and is a p-type conductor at all studied Po₂. The average TEC of Pr_0.75Sr_0.25Cr_0.5Mn_0.5O_3 − δ is 9.3 × 10^− 6 K^− 1, in the temperature range of 100–900 °C and is close to that of YSZ electrolyte. The anode polarization resistance of PSCM in wet 5%H₂ is 1.31 Ω cm² at 910 °C and in wet CH₄ at 930 °C; the polarization resistance is 1.29 Ω cm². PSCM was unstable at 900 °C in unhumidified hydrogen. Cell performance measurements carried out using graded PSCM and La_0.8Sr_0.2MnO₃ as anode and cathode respectively yielded a maximum power density of 0.18 W cm^− 2 in wet 5%H₂/Ar at 910 °C and the corresponding current density was 0.44 A cm^− 2 at 0.4 V. The activation energy for the electrochemical cell operating in wet (3% H₂O) 5%H₂/Ar fuel is 85 kJ mol^− 1.     

Characterization on electron beam evaporated α-MoO3 thin films by the influence of substrate temperature

Electrochromic molybdenum oxide (MoO₃) thin films were prepared by electron beam evaporation technique using the dry MoO₃ pellets. The films were deposited on glass and fluorine doped tin oxide (SnO₂:F or FTO) coated glass substrates at different substrate temperatures like room temperature (RT, 30 °C), 100 °C and 200 °C. The influence of substrate temperature on the structural, surface morphological and optical properties of the films has been studied. The X-ray diffraction analysis showed that the films are having orthorhombic phase MoO₃ (α-MoO₃) with 〈1 1 0〉 preferred orientation. The laser Raman scattering spectrum shows the polycrystalline nature of MoO₃ films deposited at 200 °C. The Raman-active band at 993 cm⁻¹ is corresponding to Mo–O stretching mode that is associated with the unique character of the layered structure of orthorhombic MoO₃. Needle—like morphology was observed from the SEM analysis. The energy band gap of MoO₃ films was evaluated which lies between 2.8 and 2.3 eV depending on the substrate temperature and substrates. The decrease in band gap value with increasing substrate temperature is owing to the oxygen-ion vacancies. The absorption edge shift shows the coloration effect on the films.     

Ionic conductivity of polymer electrolyte membranes based on polyphosphazene with oligo(propylene oxide) side chains

A polyphosphazene [NP(NHR)₂]_n with oligo[propylene oxide] side chains − R = –[CH(CH₃)–CH₂O]_m–CH₃ (m = 6 – 10) was synthesized by living cationic polymerisation and polymer-analogue substitution of chlorine from the intermediate precursor [NPCl₂]_n using the corresponding primary amine RNH₂. The polymer had an average molecular weight of 3.3 × 10⁵ D. Polymer electrolytes with different concentrations of dissolved lithium triflate (LiCF₃SO₃) were prepared. Mechanically stable polymer electrolyte membranes were formed using UV radiation induced crosslinking of the polymer salt mixture in the presence of benzophenone as photoinitiator. The glass transition temperature of the parent polymer was found to be − 75 °C before cross linking. It increases after crosslinking and with increasing amounts of salt to a maximum of − 55 °C for 20 wt.% LiCF₃SO₃. The ionic conductivity was determined by impedance spectroscopy in the temperature range 0–80 °C. The highest conductivity was found for a salt concentration of 20 wt.% LiCF₃SO₃: 6.5 × 10^− 6 S·cm^− 1 at 20 °C and 2.8 × 10^− 4 S cm^− 1 at 80 °C. The temperature dependence of the conductivities was well described by the MIGRATION concept.     

Intrinsic pinning properties of FeSe0.5Te0.5

The intrinsic pinning properties of FeSe_0.5Te_0.5, which is a superconductor with a critical temperature T_c of approximately 14 K, were studied through the analysis of magnetization curves obtained using an extended critical state model. For the magnetization measurements carried out with a superconducting quantum interference device (SQUID), external magnetic fields were applied parallel and perpendicular to the c-axis of the sample. The critical current density J_c under the perpendicular magnetic field of 1 T was estimated using the Kimishima model to be equal to approximately 1.6 × 10⁴, 8.8 × 10³, 4.1 × 10³, and 1.5 × 10³ A/cm² at 5, 7, 9, and 11 K, respectively. Furthermore, the temperature dependence of J_c was fitted to the exponential law of J_c(0) × exp(?αT/T_c) up to 9 K and the power law of J_c(0) × (1 ? T/T_c)ⁿ near T_c.     

High resolution emission spectroscopy of the E2Π–X2Σ+ transition of SrH and SrD

Emission spectra of SrH and SrD have been studied at high resolution using a Fourier transform spectrometer. The molecules have been produced in a high temperature furnace from the reaction of strontium metal vapor with H₂/D₂ in the presence of a slow flow of Ar gas. The spectra observed in the 18 000–19 500 cm^?1 region consist of the 0–0 and 1–1 bands of the E²Π–X²Σ⁺ transition of the two isotopologues. A rotational analysis of these bands has been obtained by combining the present measurements with previously available pure rotation and vibration–rotation measurements for the ground state, and improved spectroscopic constants have been obtained for the E²Π state. The present analysis provides spectroscopic constants for the E²Π state as ΔG(½) = 1166.1011(15) cm^?1, B_e = 3.805503(32) cm^?1, α_e = 0.098880(47) cm^?1, r_e = 2.1083727(89) Å for SrH, and ΔG(½) = 839.1283(23) cm^?1, B_e = 1.918564(15) cm^?1, α_e = 0.034719(23) cm^?1, r_e = 2.1121943(83) Å for SrD.