The effect of wood extractives on the thermal stability of different wood species

This study compares the thermal stability of different wood species, which is an important factor for the production of wood–polymer composites (WPCs), and investigates the effect of extraction on thermal properties. The chemical composition of four wood species – Quercus alba, Pinus radiata, Eucalyptus grandis and Acacia cyclops – has been determined, as the species is expected to affect the thermal stability of wood. Subsequently, the hot-water (HW) extractives, ethanol/cyclohexane (E/C) extractives and both extractives were eliminated from the wood via Soxhlet extraction and the thermal stability of the wood determined with thermogravimetric analysis (TGA) under identical conditions. The results suggest that a higher cellulose and lignin content leads to better thermal stability of wood in different temperature regimes. In all cases, the removal of extractives improved the thermal stability of the wood. The effect of combined extractions was more pronounced than of an individual extraction and E/C-extraction caused less improvement in the thermal stability of wood than HW extraction. The degradation of the investigated wood extractives occurred at low rates over a broad temperature range. Pure cellulose exhibited superior thermal stability compared to wood, but differences were observed between the investigated wood species.     

Thermogravimetric and FTIR studies of chitosan blends

Results of spectrophotometric and thermogravimetric studies of chitosan (CH) blends with polyvinyl alcohol (PVAL), starch (S) and hydroxypropylcellulose (HPC) obtained by casting from solutions in the form of transparent films containing 0–1.0 weight fraction of CH were discussed. Blends containing S are homogeneous only in the case of low-weight fraction of S (to 0.3).On the basis of results of thermodegradation in dynamic and isothermal conditions, thermal stability of the tested systems was estimated. Thermogravimetric measurements in dynamic conditions were carried out in the temperature range of 100–450 °C at constant heating rate 15 °C/min. From thermogravimetry (TG) and DTG curves the activation energy and characteristic parameters of degradation of the tested blends were determined. The observed growth of activation energy and T_p—temperature of initial weight loss, T_max—temperature of maximal rate and C_e—degree of conversion at the end of the measurement (at temperature 450 °C) along with the increase of polymer fraction (HPC and S) in the CH blend provides an evidence of improved thermal stability of the systems tested.Investigations in isothermal conditions in air at temperature from 100 to 200 °C confirmed appreciable improvement of CH thermal stability in the blends being tested.Infrared spectroscopic analysis of the blends showed a distinct stabilization of the process of chain scission. In the band at 1080 cm⁻¹ associated with absorption in –C–O–C– group during degradation of the blends at temperature 200 °C much smaller decrease due to molecular scission were observed than in the case of pure CH.     

Pyrolytic production of microporous charcoals from different wood resources

A series of porous chars has been obtained by heat treatment of unconventional raw materials, including plants belonging to short rotation woody crops (Salix viminalis, Salix fragilis). The pyrolysis conditions (1–3 h, 600–900 °C) were the same for the production of all chars, e.g., mesoporous and microporous chars. Salix viminalis wood exhibited an advantage over the other materials, because the obtained material had microporous structure such as carbon molecular sieves. Similar properties (surface area, total pore volume, pore size distribution) were observed for charcoals produced from pine wood (Pinus silvestri), but the thermal stability of these properties was inferior. Furthermore, we have also discussed economical and environmental issues associated with the exploitation of wood resources.     

Pyrolysis and smoke formation of grey alder wood depending on the storage time and the content of extractives

Grey alder (Alnus incana (L.) Moench.) wood is often used in the Baltic countries for the production of curing smoke. Unfortunately, the smoke contains an elevated concentration of polycyclic aromatic hydrocarbons (PAH). The effect of the content of wood extractives and the wood storage time after felling on the formation of benzo(a)pyrene (B(a)P), flavouring compounds and antioxidants was studied. Storage time demonstrated a considerable effect on the overall increase of the B(a)P formation. The extraction (elimination) of extractives did not show any definite coherency with the concentration of B(a)P in smoke primary condensates, which was within the range from 1.1 to 8.7 μg/kg. Storage time and the elimination of extractives increased the yields of both 2-hydroxyacetaldehyde and 1,6-anhydro-β,D-glucopyranose (levoglucosan) from 1.8 to 10 times during the pyrolysis process and smouldering. It is interesting that the intensified formation of both substances takes place simultaneously, which commonly does not occur. Nevertheless, the prolonged storage time and the elimination of extractives do not substantially improve the quality of smoke and its condensates.     

Influence of thermal treatment on the glass transition temperature of thermosetting epoxy laminate

The influence of accelerated thermal treatment of thermosetting epoxy laminate on its glass transition temperature was studied. Lamplex^® FR-4 glass fibre-reinforced epoxy laminate (used for printed circuit board manufacturing) was used in these experiments. The composite was exposed to thermal treatments at temperatures ranging from 170 °C to 200 °C for times ranging from 10 to 480 h. The glass transition temperature (T_g) was analysed via dynamic mechanical analysis (DMA). It has been proven that the glass transition temperature rapidly decreases in reaction to thermal stress. The obtained T_g data were used for Arrhenius plots for different critical temperatures (T_g-crit. = 105–120 °C). From their slopes (?E_a/R), the activation energy of the thermal degradation process was calculated as 75.5 kJ/mol. In addition to this main relaxation mechanism, DMA also recorded one smaller relaxation process in the most aged samples. Microscopic analysis of the sample structure showed the presence of pronounced small regions of degradation both on the surface and in the inner structure, which are probably the causes of microscopic delamination and the smaller relaxation process.     

The effect of processing conditions on the mechanical properties and thermal stability of highly oriented PP tapes

It has previously been shown possible to use highly oriented polypropylene (PP) tapes to create self-reinforced (all-PP) composites. It is desirable to understand the relationship between tape processing parameters and the mechanical properties and thermal stability of the tapes, as these tape properties will govern the ultimate properties of the all-PP composite. In this paper, the effects of the tape drawing parameters such as draw ratio (λ), drawing temperature and thermal annealing on the final mechanical properties, density and dimensional thermal stability of the tapes are presented. PP tapes drawn to λ = 17 possess tensile moduli of ～15 GPa and tensile strengths of ～450 MPa. PP tapes with high draw ratios, λ > 9.3, show a decrease in density, a change from transparent to opaque appearance and increased dimensional thermal stability with increasing draw ratio. The results of an investigation into the effects of a thermal annealing step, targeted at improving the dimensional thermal stability of these highly oriented PP tapes, are also presented.     

Copolymerization of ethylene with a vinyl ether bearing a fluorinated group

The copolymerization of ethylene (E) with 1H,1H,2H,2H-perfluorodecyl vinyl ether (FAVE8) by oxidative addition of salicylaldimine ligand to bis(1,5-cyclooctadiene)nickel(0)/methylaluminoxane (MAO) at room temperature and at different ethylene pressures is reported. The homopolymerization of ethylene is known to be highly active with this catalyst in contrast to the fluorinated vinyl ether which does not homopolymerize. The copolymerization of E with FAVE8 led to linear poly(E-co-FAVE8) statistic copolymers that were characterized by means of various techniques. The obtained copolymers, analyzed by FT-IR and solid state NMR spectroscopy, showed a small incorporation of the fluorinated vinyl ether. Three copolymerization reactions were investigated with different ethylene pressures (5, 10 and 50 bar) and the copolymer compositions indicated that the content of FAVE8 units depends on the ethylene pressure. The lower this pressure, the higher the content of such a fluorinated comonomer and for a 50 bar-pressure, no FAVE8 was incorporated. Thermogravimetric and differential scanning calorimetry analyses of these resulting copolymers exhibited high thermal stability, the thermal degradation starting from ca. 300 °C whereas high melting point (T_m = 129 °C) were achieved with these copolymers. Original films processed from these poly(E-co-FAVE8) copolymers illustrated hydrophobic and oleophilic characters as evidenced by water and diiodomethane contact angles of 104° and 49°, respectively.     

Stability of carbon-supported palladium nanoparticles in alkaline media: A case study of graphitized and more amorphous supports

The stability and degradation mechanism of graphitized (Graphene nanosheets) and more amorphous (Vulcan XC-72R) carbon-supported palladium nanoparticles was investigated. Coupling identical-location transmission electron microscopy (ILTEM) and electrochemistry enabled to correlate the distribution of the Pd nanoparticles under accelerated stress test (up to 1000 cycles between 0.1 and 1.23 V vs. RHE, in a 0.1 M NaOH solution at 25 °C) with changes in electrochemical accessible surface area (ECSA). The carbon-supported Pd nanoparticles undergo similar rates of degradation in terms of electrochemical surface areas on both supports. However, their mechanisms of degradation differ: on amorphous carbon, the primary mode of degradation is Pd nanoparticles detachment (and minor agglomeration), whereas on graphitized supports it is more likely their coalescence and dissolution/redeposition. “Bulk” carbon-corrosion is negligible in both cases, as proven by ex situ Raman spectroscopy. So, using a graphitized carbon support (Graphene nanosheets) versus a more amorphous one (Vulcan XC-72R) does not enable to significantly depreciate the Pd/C catalyst degradation in alkaline media.     

Effect of electron beam irradiation on the structural properties of poly(vinyl alcohol) formulations with triphenyl tetrazolium chloride dye (TTC)

Films of poly(vinyl alcohol) (PVA) composites with triphenyl tetrazolium chloride (TTC) dye were prepared and exposed to various radiation doses delivered by accelerated electrons. The results showed that at a low dose of 50 kGy, the colour difference (ΔE^*) of PVA/TTC films was increased by ∼10 times of the initial value. However, the change in colour differences did not go systematically with increasing the TTC content, in which the composite with 1.5 wt% displayed higher value than that with 3.5 wt%. The differential scanning calorimetry (DSC) showed that the presence of the TTC dye caused a depression in the melting point (T_m) and heat of fusion (ΔH_f) of the PVA bulk polymer. However, the thermogravimetric analysis (TGA) showed that the presence of the TTC dye improved the thermal stability of PVA. Also, the tensile strength at break of PVA/TTC composites was improved after electron beam irradiation.     

Thermal racemization of biaryl atropisomers

Many biaryl compounds possess atropisomerism due to the steric hindrance of substituents at the ortho-position of the two aromatic moieties. Upon heating, atropisomers may have enough energy to surpass the rotational energy barrier and racemize. The thermal stability of five atropisomers was studied using chiral chromatography by following the change in enantiomeric excess ratio at different temperatures. The first order racemization reaction rate was obtained at a given temperature as the slope of the change in enantiomeric excess ratio versus time. For each atropisomer, the racemization rates at different temperatures led to the value of the rotational energy barrier for racemization, ΔG³, and to the racemization half lifetime, t_1/2, indicating the atropisomer thermal stability. Binaphthol started to racemize significantly at temperature of 190 °C and above while binaphthyldiamine was much more stable showing little or very minor racemization up to 210 °C. A chloro-substituted phenylamino-naphthol was very sensitive to thermal racemization starting at a low 40 °C.     

Molecular characterization of Ulex europaeus biochar obtained from laboratory heat treatment experiments – A pyrolysis–GC/MS study

Gorse species (Ulex sp.) are ubiquitous in the shrublands of NW Spain and have the potential to become key players in an integral biofuel/biochar program in NW Spain. Here we present molecular characterization (using pyrolysis–GC/MS) of a biochar “thermosequence” obtained by laboratory heating of Ulex europaeus wood in a muffle furnace between 200 and 600 °C (T_CHAR). Low temperature chars (T_CHAR ≤ 350 °C) produced significant amounts of pyrolysis products of which the precursor biopolymer could be recognized, while high-temperature chars (T_CHAR ≥ 400 °C) produced mainly phenols and monocyclic and polycyclic aromatic hydrocarbons, which are not specific for any biopolymer. Carbohydrate could hardly be recognized at T_CHAR ≥ 350 °C. The thermal rearrangement of polyphenols, mainly lignin, was reflected in more detail (1) C₃-side chain shortening and probably depolymerization (T_CHAR 200–350 °C), (2) demethoxylation of syringyl and probably also some guaiacyl lignin (T_CHAR 300–400 °C), (3) elimination of virtually all remaining methoxyl groups (T_CHAR 350–400 °C), through dehydroxylation and demethoxylation, (4) almost complete dehydroxylation of lignin and other biopolymers (T_CHAR 400–500 °C), (5) progressive condensation into polyaromatic structures (T_CHAR 300–500 °C) and (6) partial elimination of alkyl bridges between (poly)aromatic moieties (T_CHAR 450–500 °C). These results were supported by Fourier transform infrared spectroscopy (FTIR) of the same samples. We conclude that pyrolysis–GC/MS can be used as a rapid molecular screening method of gorse-derived biochar. Molecular properties elucidation is an essential part of predicting the stability and agronomical behavior of gorse-derived biochar after future implementation in soils.     

A thermogravimetric study of structural changes of lime wood (Tilia cordata Mill.) induced by exposure to simulated accelerated UV/Vis-light

A series of experiments were carried out to investigate photodegradation of lime wood (Tilia cordata Mill.) during artificial UV/Vis light irradiation for 600 h. Photodegradation of the wood samples was evaluated by thermogravimetry throughout the irradiation period at an interval of 100 h.The alteration of wood was observed by means of the peak temperatures of DTG variation and by the mass losses observed during heating, evaluated on the basis of the measured thermal data. The results obtained indicate a shifting of the DTG maxima to lower temperatures which may be related to the decreasing in the stability components during photodegradation. The values of the overall activation energies corresponding of the decomposition process progressively decreases.The decreased temperatures decomposition processes, weight losses and integral area of the peaks assigned to lignin, the increased integral area of the peaks assigned to hemicelluloses could be explained by new formed structures, mainly due to formation of reactive species.     

Effects of Fe doping on the electrochemical performance of LiCoPO4/C composites for high power-density cathode materials

LiCo_1?xFe_xPO₄/C composites with various amounts of Fe (x = 0, 0.05 and 0.1) were synthesized by vibrant type ball-milling coupled with microwave heating to investigate the role of doped Fe²⁺ in LiCo_1?xFe_xPO₄/C composites. The initial charge–discharge curves and cyclic voltammetry profiles of LiCo_1?xFe_xPO₄/C composites apparently featured an improved kinetic property compared to LiCoPO₄. It was observed that the initial discharge capacity (120 mA hg^?1) of LiCo_0.95Fe_0.05PO₄ is higher than that (108 mA hg^?1) of LiCoPO₄ and the difference between the oxidation–reduction peaks is getting smaller with the increase of Fe doping. The electrochemical improvement in LiCo_1?xFe_xPO₄/C composites could be attributed to the enhanced Li⁺ diffusivity induced by the enlargement of 1D channel in polyanion structure of LiCoPO₄.     

TiO2/polyaniline composites： An efficient photocatalyst for the degradation of methylene blue under natural light

Polyaniline (PAn) sensitized nanocrystalline TiO_2 composites (TiO_2/PAn) were successfully prepared and used as an efficient photocatalyst for the degradation of dye methylene blue (MB).The results showed that PAn was able to sensitize TiO_2 efficiently and the composite photocatalyst could be activated by absorbing both the ultraviolet and visible light (λ:190～800nm),whereas pure TiO_2 absorbed ultraviolet light only (λ<380nm).Under the irradiation of natural light,MB could be degraded more efficiently on the TiO_2/PAn composites than on the TiO_2.Furthermore,it could be easily separated from the solution by simple sedimentation.     

Thermal stability of fatty acids in subcritical water

In this work, hydrolytic reaction conditions of various temperatures (300–370 °C) and times (0–30 min) at a constant pressure of 20 MPa were applied to the thermal decomposition of three kinds of fatty acids (FAs), stearic acid, oleic acid, and linoleic acid, in subcritical water. The degradation characteristics were investigated from the derived data, and the thermal stability of FAs in subcritical water was estimated. The primary reactions we observed were isomerization and pyrolysis of FAs. The main pathway of degradation was deduced by analyzing the contents of pyrolyzed products. We found that more saturated FAs have greater thermal stability in subcritical water. All FAs remained stable at 300 °C or below. Based on these results, we recommend that hydrolysis of vegetable oils and fats using subcritical water should be carried out below 300 °C (at 20 MPa) and for less than 30 min to obtain high-yield FA production.     

Thermal degradation and evolved gas analysis: A polymeric blend of urea formaldehyde (UF) and epoxy (DGEBA) resin

A polymeric blend has been prepared using urea formaldehyde (UF) and epoxy (DGEBA) resin in 1:1 mass ratio. The thermal degradation of UF/epoxy resin blend (UFE) was investigated by using thermogravimetric analyses (TGA), coupled with FTIR and MS. The results of TGA revealed that the pyrolysis process can be divided into three stages: drying process, fast thermal decomposition and cracking of the sample. There were no solid products except ash content for UFE during combustion at high temperature. The total mass loss during pyrolysis at 775 °C is found to be 97.32%, while 54.14% of the original mass was lost in the second stage between 225 °C and 400 °C. It is observed that the activation energy of the second stage degradation during combustion (6.23 × 10⁻⁴ J mol⁻¹) is more than that of pyrolysis (5.89 × 10⁻⁴ J mol⁻¹). The emissions of CO₂, CO, H₂O, HCN, HNCO, and NH₃ are identified during thermal degradation of UFE.     

MOF-derived ZnCo2O4/C wrapped on carbon fiber as anode materials for structural lithium-ion batteries

In this work, large area MOF-derived ZnCo₂O₄/C anchored on carbon fiber as high-performance anode materials was fabricated via a facile method and subsequent annealing treatment.     

Study of cosurfactant effect on nanoemulsifying area and development of lercanidipine loaded (SNEDDS) self nanoemulsifying drug delivery system

The present study deals with the development and characterization of self-nanoemulsifying drug delivery system (SNEDDS) to improve the oral bioavailability of poorly soluble third generation calcium channel blocker lercanidipine (LER). Solubility of the LER was estimated in various oils, cosurfactants and surfactants which were grouped into two different combinations to construct pseudoternary phase diagrams. Various thermodynamic stability and dispersibility tests were performed on the formulations from phase diagram. After constructing phase diagram of two different combinations NL-I and NL-II, the effect of cosurfactants on the nanoemulsifying area was studied and the effect of number and length of hydrophobic alkyl chains of cosurfactant in its emulsification capacity was proved. Percentage transmittance, emulsification time, viscosity and droplet size analysis were used to characterize optimized formulations. The optimized formulation composed of Cremophor EL (45% wt/wt), (13.5% wt/wt) Caproyl 90 with (1.5% wt/wt) Transcutol® HP as per limits of inactive ingredients guidelines of FDA and Maisine oil (10% wt/wt). The mean droplet size in selected nanocarrier system was 20.01 nm. The in vitro dissolution profile of LER SNEDDS was found significant in comparison to the marketed LER (Zanidip) tablet and pure drug in pH 1.2, 4.5 and 6.8 buffers. Empty hard gelatin capsule shells were filled using Pfizer's Licap technology and charged on stability conditions of 30 °C/65% RH, 40 °C/65%RH and 50 °C/75% in glass bottles where no significant degradation (p > 0.05) was observed in 3 months. The results indicate that SNEDDS of LER, owing to nanosized, has potential to enhance the absorption of drug.     

Synthesis and second-order nonlinear optical properties of a crosslinkable functionalized hyperbranched polymer

A new implementation of copper-free thermal Huisgen 1,3-dipolar crosslinking reaction into a high T_g hyperbranched polyimide polymer in order to stabilize the electro-optic (EO) activity of second-order non linear materials is reported. Towards this goal, two different synthetic approaches were explored. The first strategy is based on the post-functionalization of the polymer with mixtures of DR1 azido derivative and propargylic alcohol, whereas, the second consists in the preparation of two complementary functionalized hyperbranched polymers that are mixed just before the preparation of films. Materials exhibit good second-order nonlinear optical coefficients (d₃₃) close to 30 pm/V at the fundamental wavelength of 1064 nm. Moreover, the thermal stability of the NLO properties of these materials reaches temperatures as high as 150 °C, and probably higher. This represents the highest thermal stability of crosslinkable EO polymers based on the crosslinking Huisgen reaction.     

Thermodynamic properties of liquid Au-Cu-Sn alloys determined from electromotive force measurements

A thermally conductive linear low-density polyethylene (LLDPE) composite with aluminum nitride (AlN) as filler was prepared in a heat press molding. Differential scanning calorimeter results indicated that the AlN filler decreases the degree of crystallinity of LLDPE, and has no obvious influence on the melting temperature of LLDPE. Experimental results demonstrated that the LLDPE composites display a high thermal conductivity of 1.25 W/m K and improved thermal stability at 70 wt% AlN content as compared to pure LLDPE. The dielectric constant and dissipation factor increased with AlN content, however, they still remained at relatively low levels, i.e., <5 in wider frequency range from 10 to 10⁶ Hz. The surface treatment of AlN particles had a beneficial effect on improving the thermal conductivity and dielectric constant, whereas, the dissipation factor was less affected. Additionally, the obtained AlN/LLDPE composites have possessed rather low dielectric constant and high electrical insulation, which is suitable for substrate and packaging materials.