Dynamic hollow-fibre liquid phase microextraction of dinitrophenols from human plasma: Optimization of an extraction flow system using experimental design methodology

The utility of a dynamic hollow-fibre liquid phase microextraction method (optimized using a four-variable experimental design and response surface modelling) for extracting dinitrophenolic compounds from human plasma samples was evaluated. The investigated variables were donor phase salt concentration (10-400 mM), donor phase pH (2-6), acceptor phase pH (7-12), and donor/acceptor phase flow rates (30/7.5 to 70/17.5 μL min⁻¹). Four dinitrophenol pesticides were used as model substances at concentrations of 0.1 μg mL⁻¹ in spiked human plasma samples. Extraction efficiencies ranging from 42 to 77% with RSDs below 9 were achieved with the optimized method. The flow rate and acceptor pH were shown to strongly affect the extraction efficiency for all compounds, while the donor phase pH and salt concentration had minor effects. With a well-defined acceptor phase pH and flow rate the system exhibited high robustness. The limits of quantification for the investigated compounds, using the presented extraction method followed by liquid chromatography/electrospray ionization mass spectrometry in selected ion monitoring mode, ranged from 0.05 to 0.1 μg mL⁻¹ plasma.     

Determination of alkaloids in Corydalis yanhusuo using hollow-fibre liquid phase microextraction and high performance liquid chromatography

Hollow fibre based liquid phase microextraction (HF-LPME) with high performance liquid chromatography (HPLC) was developed for the determination of alkaloids in Corydalis yanhusuo. Three alkaloids (protopine, tetrahydropalmatine, tetrahydroberberine) were extracted from a 10 mL alkaline sample (donor phase) to an organic phase impregnated in the pores of the hollow fibre, and then, they were extracted to an acidic solution (acceptor phase) in the lumen of the fibre. The extract was determined directly by HPLC. Parameters affecting the HF-LPME include the organic solvent, pH of the donor and the acceptor phase, the extraction time and the stirring speed were investigated systematically. To minimize the error of the injection, palmatine was added as an internal standard (I.S.). Under optimal conditions, calibration curves were obtained in the range of 0.1–1.0 mg L⁻¹ with a reasonable linearity (r ² > 0.993) and the limits of detection (LODs) ranged between 10.0 × 10⁻³ mg L⁻¹ and 13.7 × 10⁻³ mg L⁻¹. Additionally, enrichment factors with 100 to 184-fold were obtained. The method was then applied to the crude extract of Corydalis yanhusuo successfully.     

Study of mass transfer in a dynamic hollow‐fibre liquid phase microextraction system

The extraction characteristics of a dynamic hollow‐fibre liquid phase microextraction system were investigated by studying the mass transfer and diffusion rates of dinitrophenols from plasma samples over the liquid membrane (dihexylether). The measured diffusion coefficients were compared with theoretical values calculated from Stokes diameters. The diffusion mechanism was simulated by computer and the most polar compounds, 2,4‐dinitrophenol and 4,6‐o‐dinitrocresol, had associated diffusion coefficients that were close to the calculated theoretical values. 2‐sec‐Butyl‐4,6 dinitrophenol and 2‐tert‐butyl‐4,6‐dinitrophenol, the compounds with the highest log P values, were retained by the polypropylene membrane, which reduced the experimentally observed diffusion rates to about half of the theoretical values. The retention was most likely due to dispersive forces interacting with the pore inner walls. Extraction was linearly correlated with time for all compounds and the repeatability was high (RSDs 7–11%), even for the shortest extraction times. Method LOD as the amount injected ranged between 0.3 and 3.1 ng for an extraction cycle of 213 s.     

Rapid determination of atrazine in environmental water samples by a novel liquid phase microextraction

A novel method was described for the rapid determination of atrazine using dispersive liquid phase microextraction in combination with high performance liquid chromatography （HPLC）. Possible impact parameters such as sample pH, extraction and disperser solvents, salting-out effect, and extraction time were investigated. The experimental results indicated that proposed method possessed an excellent analytical performance, The linear range, detection limit, and precision （R.S.D.） were 0.1- 50 ng mL- 1 （R2 = 0.9955）, 0.601 ng mL- 1 and 6,4%, respectively. The proposed method was validated with the real water samples, and the spiked recoveries were in the range of 69.9-89.8%, respectively. These results indicated that the established method with high enrichment factor, short extraction time was an excellent alternative for the routine analysis of atrazine in environmental samples. 2007 Qing Xiang Zhou. Published by Elsevier B.V. on behalf of Chinese Chemical Society. All rights reserved.     

A rapid ultrasound-assisted dispersive liquid–liquid microextraction followed by ultra-performance liquid chromatography for the simultaneous determination of seven benzodiazepines in human plasma samples

A simple and efficient ultrasound-assisted dispersive liquid–liquid microextraction (UA-DLLME) method has been developed for the determination of seven benzodiazepines (alprazolam, bromazepam, clonazepam, diazepam, lorazepam, lormetazepam and tetrazepam) in human plasma samples. Chloroform and methanol were used as extractant and disperser solvents, respectively. The influence of several variables (e.g., type and volume of dispersant and extraction solvents, pH, ultrasonic time and ionic strength) was carefully evaluated and optimized, using an asymmetric screening design 3²4²//16. Analysis of extracts was performed by ultra-performance liquid chromatography coupled with photodiode array detection (UPLC-PDA). Under the optimum conditions, two reversed-phases, Shield RP18 and C18 columns were successfully tested, obtaining good linearity in a range of 0.01–5 μg mL⁻¹, with correlation coefficients r > 0.996. Quantification limits ranged between 4.3–13.2 ng mL⁻¹ and 4.0–14.8 ng mL⁻¹, were obtained for C18 and Shield RP18 columns, respectively. The optimized method exhibited a good precision level, with relative standard deviation values lower than 8%. The recoveries studied at two spiked levels, ranged from 71 to 102% for all considered compounds. The proposed method was successfully applied to the analysis of seven benzodiazepines in real human plasma samples.     

Multivariate optimization of the hollow fiber-based liquid phase microextraction of lead in human blood and urine samples using graphite furnace atomic absorption spectrometry

The present study developed a liquid-phase microextraction based on hollow fiber coupled with graphite furnace atomic absorption spectrometry for the effective extraction and quantitation of lead from urine and blood samples. A multivariate design was used for the optimization of the experimental conditions to ensure high extraction efficiency. Six factors (solvent type, chelating agent, time extraction, temperature, donor phase pH, and acceptor phase pH) were obtained by screening eleven factors of the Plackett–Burman design; these were optimized using the central composite design of response surface methodology. The optimum conditions of donor phase pH, acceptor phase pH, temperature, and extraction time were 5, 9.5, 40 °C, and 120 min, respectively. In addition, oleic acid containing dicyclohexyl-18-krone-6 was used for the membrane phase. Under optimal conditions, the enrichment factor, limit of detection, and limit of quantification were obtained in the ranges of 21.3–18.7, 0.001–0.002 ng mL^?1, and 0.008–0.01 ng mL^?1, respectively, in urine and blood samples. The linearity of the calibration curve was established for the concentration of Pb in the range of 1–50 ng mL^?1 (r²?=?0.9983). Finally, the performance of the developed method was evaluated for the determination of lead in urine and blood samples, and satisfactory results were obtained (RSDs <?10% with recovery >?95).     

Hollow fiber-based liquid phase microextraction combined with high-performance liquid chromatography for the analysis of gabapentin in biological samples

Three-phase hollow fiber microextraction technique combined with high performance liquid chromatography-ultra violet (HPLC-UV) was applied for the extraction and determination of gabapentin in biological fluids. Gabapentin (GBP) was derivatized with 1-fluoro-2,4-dinitrobenzene, as a UV absorbent agent in borate buffer (pH 8.2) before extraction. The derivative product of GBP was extracted from the 8.5 mL of acidic solution (source phase) into an organic phase (dihexyl ether) impregnated in the pores of a hollow fiber and finally back-extracted into 24 μL of the basic solution (pH 9.1) located inside the lumen of the hollow fiber (receiving phase). The extraction took place due to pH gradient between the inside and outside of the hollow fiber membrane. In order to achieve maximum extraction efficiency, different parameters affecting the extraction conditions were optimized. Under the optimized conditions, preconcentration factor of 95 and detection limit (LOD) of 0.2 μg L⁻¹ were obtained. The calibration graph was linear within the range of 0.6-5000 μg L⁻¹. Finally, the feasibility of the proposed method was successfully confirmed by extraction and determination of GBP in human urine and plasma samples in the range of microgram per liter and suitable results were obtained (RSDs < 6.3%).     

Evaluation of solid-phase microextraction for the study of protein binding in human plasma samples

Solid-phase microextraction (SPME) in combination with capillary gas chromatography and a nitrogen-phosphorous detector is used to study protein binding in human plasma samples. Local anesthetics of the amide-type (ropivacaine, bupivacaine, mepivacaine, prilocaine, and lidocaine) are used as model compounds in this evaluation. Carbowax/divinylbenzene (CW/DVB), polyacrylate, and polydimethylsiloxane fibers are tested. Sampling on CW/DVB fibers give the highest recovery in plasma samples compared with other fibers. Ultrafiltrate spiked with each of the substances is used for the construction of calibration curves. The protein binding is investigated at four different total concentrations from 0.5 to 15.0 microM. The degree of protein binding increases when the solute concentration decreases. Protein binding of the five solutes is investigated at four pH levels (6.4, 7.4, 8.4, and 9.4). It is found that protein binding increased with increasing pH. The influence of temperature variation (from 32 degrees C to 40 degrees C) on protein binding is also investigated. The protein binding decreases when the temperature increases. The methodology is validated and good correlation and precision are obtained. Back-calculated quality control samples give accuracy within 20% of theoretical values for all five substances. This study shows that SPME as a sample-preparation method gives the same protein binding for the studied local anesthetics as that achieved using earlier presented methods.     

Trace determination of hexabromocyclododecane diastereomers in water samples with temperature controlled ionic liquid dispersive liquid phase microextraction

A novel temperature controlled ionic liquid dispersive liquid phase microextraction(TCIL-DLPME) coupled with rapid resolution liquid chromatography-electrospray tandem mass spectrometry(RRLC-ESI-MS-MS) has been developed for the enrichment and determination of three hexabromocyclododecane diastereomers(HBCDs) in water samples.Green solvent ionic liquid(IL) was used as extraction solvent instead of toxic organic solvents.This technique also avoided the usage of dispersive solvent.Some important parameters that might affect the extraction efficiency were optimized.Under the optimum conditions,good linear relationship,sensitivity and reproducibility were obtained.All the limits of detection for the three diastereomers were 0.1 ng/ mL.The linear range was obtained in the range of 1-100 ng/mL for the total amount of three HBCD diastereomers.It was satisfactory to analyze real environmental water samples with the recoveries ranging from 77.2%to 99.3%.The main advantage of the method is toxic organic solvent-free.     

Optimization of temperature-controlled ionic liquid dispersive liquid phase microextraction combined with high performance liquid chromatography for analysis of chlorobenzenes in water samples

Temperature-controlled ionic liquid dispersive liquid phase microextraction (TCIL-DLPME) combined with high performance liquid chromatography-diode array detection (HPLC-DAD) was applied for preconcentration and determination of chlorobenzenes in well water samples. The proposed method used 1-butyl-3-methylimidazolium hexafluorophosphate ([C₄mim][PF₆]) as the extraction solvent. The effect of different variables on extraction efficiency was studied simultaneously using an experimental design. The variables of interest in the TCIL-DLPME were extraction solvent volume, salt effect, solution temperature, extraction time, centrifugation time, and heating time. The Plackett-Burman design was employed for screening to determine the variables significantly affecting the extraction efficiency. Then, the significant factors were optimized by using a central composite design (CCD) and the response surface equations were developed. The optimal experimental conditions obtained from this statistical evaluation included: extraction solvent volume, 75 μL; extraction time, 20 min; centrifugation time, 25 min; heating time, 4 min; solution temperature, 50 °C; and no addition of salt. Under optimal conditions, the preconcentration factors were between 187 and 298. The limit of detections (LODs) ranged from 0.05 μg L⁻¹ (for 1,2-dichlorobenzene) to 0.1 μg L⁻¹ (for 1,2,3-trichlorobenzene). Linear dynamic ranges (LDRs) of 0.5-300 and 0.5-500 μg L⁻¹ were obtained for dichloro- and trichlorobenzenes, respectively. The performance of the method was evaluated for extraction and determination of chlorobenzenes in well water samples in micrograms per liter and satisfactory results were obtained (RSDs < 9.2%).     

Ultrasound assisted supramolecular liquid phase microextraction procedure for Sudan I at trace level in environmental samples

A method based on supramolecular liquid phase microextraction has been developed for the preconcentration and determination of trace levels of Sudan I. 1-decanol and tetrahydrofuran were used as supramolecular solvent components. Trace levels of Sudan I were extracted into the extraction solvent phase at pH = 4.0 Analytical parameters such as pH value, supramolecular solvent volume, ultrasonication, centrifugation, model solution volume, matrix effects have been optimized. The limit of detection and the limit of quantification values for Sudan I were calculated as 1.74 μg L⁻¹ and 5.75 μg L⁻¹, respectively. In order to determine the accuracy of the method, addition and recovery studies were carried out to environmental samples.     

Determination of lewisite constituents in aqueous samples using hollow-fibre liquid-phase microextraction followed by gas chromatography-mass spectrometry

The applicability of hollow-fibre liquid-phase microextraction for extracting 2-chlorovinyldichloroarsine (lewisite 1), bis(2-chlorovinyl)chloroarsine (lewisite 2), tris(2-chlorovinyl)arsine (lewisite 3) and arsenic trichloride from aqueous samples is reported. Parameters affecting the extraction efficiency of these chemicals were optimised. These parameters included the type of derivatising agent, extraction solvent, derivatisation method, pH, ionic strength, stirring speed and extraction time. A linear range between 0.002 and 0.2 μg/mL was established for the lewisites with good square regression coefficients (0.9955–0.9992). Good reproducibility with relative standard deviations (RSDs) from 8 to 10 % was achieved. The limit of detection was 0.002 μg/mL for the lewisites and 0.005 μg/mL for arsenic trichloride (3:1 signal-to-noise ratio). The extraction method was validated with a proficiency test sample issued by the Organisation for the Prohibition of Chemical Weapons (OPCW). The rapidity and precision of the new method should help deter against the employment of lewisite as a chemical warfare agent: its use could be confirmed easily from analysis of aqueous samples.     

Immunoaffinity in-tube solid phase microextraction coupled with liquid chromatography-mass spectrometry for analysis of fluoxetine in serum samples

The inherent selectivity of the antibody was combined with in-tube solid-phase microextraction by immobilization of the antibody into the fused silica capillary. A sensitive, selective, and reproducible immunoaffinity in-tube solid-phase microextraction coupled with liquid chromatography-mass spectrometry (in-tube SPME/LC-MS) method was developed, and validated for fluoxetine analysis in human serum. Important factors in the optimization of in-tube SPME variables, as well as the evaluation of the immunoaffinity capillary capacity are discussed. The in-tube SPME/LC-MS method presented a limit of quantitation of 5.00 ng/mL, and precision intra-assays with RSDs lower than 5%. The response of the in-tube SPME/LC-MS method for fluoxetine was linear over a dynamic range from 5.00 to 50.00 ng/mL, with correlation coefficients better than 0.998. Based on analytical validation it was demonstrated that in-tube SPME/LC-MS method offers high sensitivity, selectivity, and enough reproducibility to permit the quantification of fluoxetine in human serum at therapeutic levels. Thus, the proposed SPME/LC method can be useful tool to determine fluoxetine serum concentrations in patients receiving therapeutic dosages.     

Solidified floating organic drop microextraction combined with high performance liquid chromatography for the determination of carbamazepine in human plasma and urine samples

Solidified floating organic drop microextraction (SFODME) in combination with high performance liquid chromatography was used for separation/preconcentration and determination of carbamazepine (CBZ) in human plasma and urine samples. Parameters that affect the extraction efficiency such as the type and volume of extraction solvent, ionic strength, sodium hydroxide concentration, stirring rate, sample volume and extraction time, were investigated and optimized. Under the optimum conditions (extraction solvent, 40 μL of 1-undecanol; sodium hydroxide concentration, 1 mol/L; temperature, 50 ℃; stirring speed, 400 r/min; sample volume, 8 mL; sodium chloride concentration, 3% (w/v) and extraction time, 60 min) the calibration curve was found to be linear in the mass concentration range of 0.4-700.0 μg/L. The limit of detection (LOD) was 0.1 μg/L and the relative standard deviation (RSD) for six replicate extraction and determination of carbamazepine at 100 μg/L level was found to be 4.1%. The method was successfully applied to the determination of CBZ in human plasma and urine samples.     

Application of ionic liquid in liquid phase microextraction technology

Ionic liquids (ILs) are novel nonmolecular solvents. Their unique properties, such as high thermal stability, tunable viscosity, negligible vapor pressure, nonflammability, and good solubility for inorganic and organic compounds, make them excellent candidates as extraction media for a range of microextraction techniques. Many physical properties of ILs can be varied, and the structural design can be tuned to impart the desired functionality and enhance the analyte extraction selectivity, efficiency, and sensitivity. This paper provides an overview of the applications of ILs in liquid phase microextraction technology, such as single‐drop microextraction, hollow fiber based liquid phase microextraction, and dispersive liquid–liquid microextraction. The sensitivity, linear calibration range, and detection limits for a range of target analytes in the methods were analyzed to determine the advantages of ILs in liquid phase microextraction.     

A fully automated effervescence-assisted switchable solvent-based liquid phase microextraction procedure: Liquid chromatographic determination of ofloxacin in human urine samples

A novel fully automated effervescence-assisted switchable solvent-based liquid phase microextraction procedure has been suggested. In this extraction method, medium-chain saturated fatty acids were investigated as switchable hydrophilicity solvents. The conversion of fatty acid into hydrophilic form was carried out in the presence of sodium carbonate. The injection of sulfuric acid into the solution decreased the pH value of the solution, thus, microdroplets of the fatty acid were generated. Carbon dioxide bubbles were generated in-situ, and promoted the extraction process and final phase separation. The performance of the suggested approach was demonstrated by the determination of ofloxacin in human urine samples using high-performance liquid chromatography with fluorescence detection. This analytical task was used as a proof-of-concept example. Under the optimal conditions, the detector response of ofloxacin was linear in the concentration ranges of 3·10⁻⁸−3·10⁻⁶ mol L⁻¹. The limit of detection, calculated from a blank test based on 3σ, was 1·10⁻⁸ mol L⁻¹. The results demonstrated that the presented approach is highly cost-effective, simple, rapid and environmentally friendly.     

Ultratrace determination of carbamate pesticides in water samples by temperature controlled ionic liquid dispersive liquid phase microextraction combined with high performance liquid phase chromatography

A simple and sensitive method was developed for the determination of three carbamate pesticides in water samples. It is based on temperature controlled ionic liquid dispersive liquid phase microextraction combined with high-performance liquid chromatography. The ionic liquid 1-hexyl-3-methylimidazolium hexafluorophosphate was used as the extractant, and the factors affecting the extraction were investigated in detail. The detection limits obtained for isoprocarb, diethofencarb and fenothiocarb are 0.91, 0.45, and 1.40 μgL^-1, respectively, and the precisions are in the range between 1.0 and 1.8% (n?=?6). The method was validated with environmental water samples and the results indicate that it represents a viable alternative to existing methods.

Assessment of specific migration to aqueous simulants of a new active food packaging containing essential oils by means of an automatic multiple dynamic hollow fibre liquid phase microextraction system

The determination of specific migration in the three aqueous food simulants (water, 3% acetic acid and 10% ethanol) from experimental active packaging polypropylene-based films containing natural essential oils as active agents has been carried out for the first time by a two-phase hollow fibre liquid phase microextraction (HFLPME). Due to the high number of variables involved, an experimental design has been applied. High throughput, with six samples running simultaneously in a highly automated system working in dynamic extraction mode, has been achieved. The main analytical characteristics are detection limits as low as 0.01 μg kg⁻¹, linearity higher than 0.99 for almost 5 magnitude orders, average precision below 16% as RSD and concentration factors ranging from 4 to 189. Migration of 43 compounds including terpenes, alkanes, plastic additives and degradation compounds is reported. According to the results obtained and European legislation, the packaging prototypes tested could be safely marketed.     

Automated on-line liquid–liquid extraction system for temporal mass spectrometric analysis of dynamic samples

Most real samples cannot directly be infused to mass spectrometers because they could contaminate delicate parts of ion source and guides, or cause ion suppression. Conventional sample preparation procedures limit temporal resolution of analysis. We have developed an automated liquid–liquid extraction system that enables unsupervised repetitive treatment of dynamic samples and instantaneous analysis by mass spectrometry (MS). It incorporates inexpensive open-source microcontroller boards (Arduino and Netduino) to guide the extraction and analysis process. Duration of every extraction cycle is 17 min. The system enables monitoring of dynamic processes over many hours. The extracts are automatically transferred to the ion source incorporating a Venturi pump. Operation of the device has been characterized (repeatability, RSD = 15%, n = 20; concentration range for ibuprofen, 0.053–2.000 mM; LOD for ibuprofen, ∼0.005 mM; including extraction and detection). To exemplify its usefulness in real-world applications, we implemented this device in chemical profiling of pharmaceutical formulation dissolution process. Temporal dissolution profiles of commercial ibuprofen and acetaminophen tablets were recorded during 10 h. The extraction-MS datasets were fitted with exponential functions to characterize the rates of release of the main and auxiliary ingredients (e.g. ibuprofen, k = 0.43 ± 0.01 h⁻¹). The electronic control unit of this system interacts with the operator via touch screen, internet, voice, and short text messages sent to the mobile phone, which is helpful when launching long-term (e.g. overnight) measurements. Due to these interactive features, the platform brings the concept of the Internet-of-Things (IoT) to the chemistry laboratory environment.     

Comparison of solid phase microextraction and hollow fiber liquid phase microextraction for the determination of pesticides in aqueous samples by gas chromatography triple quadrupole tandem mass spectrometry

This work compares two miniaturised sample preparation methods, solid phase microextraction (SPME) and hollow fiber liquid phase microextraction (HF-LPME), in combination with gas chromatography coupled to tandem mass spectrometry with a triple quadrupole analyzer for the determination of 77 pesticides in drinking water. In the case of SPME, extraction temperature and time were optimized by experimental design, although other parameters, as desorption time, pH, and ionic strength, were also evaluated. The extraction and desorption solvents [octanol/dihexyl ether (75:25, v/v) and cyclohexane, respectively], as well as the extraction and desorption time, ionic strength, and pH, were studied for the HF-LPME procedure. Under the optimal conditions, recoveries (70.2–113.5% for SPME and 70.0–119.5% for HF-LPME), intra-day precision (2.1–19.4% for SPME and 4.3–22.5% for HF-LPME), inter-day precision (5.2–21.5% for SPME and 8.4–27.3% for HF-LPME), and limits of detection, between 0.1 and 28.8 ng/L for SPME and 0.2 and 47.1 ng/L for HF-LPME and overall uncertainty (9.6–25.2% for SPME and 13.3–27.5% for HF-LPME) were established for both extraction procedures. Finally, the proposed methods were successfully applied to the analysis of 41 drinking water samples, and similar results were obtained with both extraction approaches.