Adsorption and inactivation behavior of horseradish peroxidase on cellulosic fiber surfaces

The physical immobilization behavior of horseradish peroxidase (HRP) on cellulosic fiber surfaces was characterized using adsorption and inactivation isotherms measured by the depletion method followed by fitting of Langmuir’s and Freundlich’s models to the experimental data. The adsorption and inactivation behavior of simpler and relatively non-porous high and low crystalline cellulosic substrates (microcrystalline cellulose and regenerated cellulose) as well as more complex and porous cellulosic pulp fibers (bleached kraft softwood fibers) were investigated. The effect of the sorbent surface energy on HRP adsorption was demonstrated by increasing the hydrophobicity of the cellulosic fibers using an internal sizing agent. The influence of the fiber surface charge density on HRP adsorption was studied via modification of the cellulosic fibers using TEMPO (2,2,6,6-tetramethyl-1-piperidiniloxy radical)-mediated oxidation methods. Results showed that hydrophobic interactions had a much larger effect on HRP adsorption than electrostatic interactions. More hydrophobic fiber surfaces (lower polar surface energy) result in larger enzyme-fiber binding affinity constants and higher binding heterogeneity. It was also found that oxidation of the cellulosic fiber substrate reduces enzyme adsorption affinity but significantly increases the loading capacity per unit weight of the surface.     

Inverse gas chromatography study on partially esterified paper fiber

Paper fiber was treated in a heterogeneous esterification reaction with four different fatty acids. This fiber was used to strengthen polyethylene (PE) composites. Modified and unmodified cellulose fiber was characterized with inverse gas chromatography. In previous work, characterization was also carried with X-ray photoelectron spectroscopy (XPS), solid-state NMR, differential scanning calorimetry and thermogravimetry. Individual fibers were found to be covered with the corresponding esters (cellulose undecylenate, undecanoate, oleate, stearate) with partial degrees of substitution of the cellulose. Comparison of XPS and NMR results showed that the surface degree of substitution of the cellulose fiber was higher than for the bulk, showing that the esterification reaction was a surface phenomenon. The aim of this work was to acquire information on the surface characteristics of the fiber and to see whether it could be correlated to PE composite mechanical strength results. The conclusions are that polar probes seem to diffuse more into the fibers than the non-polar probes, as the non-polar component of the surface tension of the modified fiber is much lowered towards that of PE, while donor-acceptor characteristics are hardly changed by esterification. The ester with the lowest non-polar component of the surface energy, the oleate, also gives the composite with the best mechanical properties.     

Surface oxidation of polyethylene using an atmospheric pressure glow discharge with liquid electrolyte cathode

This study investigated the action of an atmospheric pressure air glow discharge (APGD) with aqueous electrolyte cathode onto the surface of polyethylene (PE) films. Distilled water and aqueous solutions of KCl and HCl were utilized as a cathode. The surface properties of PE were characterized by contact angle measurement followed by surface free energy calculation, Fourier transform infrared by attenuated total reflectance (FTIR-ATR), and XPS. After treating the PE surface, we observed OH groups, CO groups in ester, ketone, and carboxyl groups, and CO groups in unsaturated ketones and aldehydes. For a treatment time of 20 min and a discharge current of 40 mA, atomic concentrations of O and N were 12% and 2%, respectively, under distilled water application. Modification processes were able to improve the surface free energy of PE.     

Microstructure and surface properties of fibrous and ground cellulosic substrates

Cotton and linen fibers were ground in a ball-mill, and the effect of grinding on the microstructure and surface properties of the fibers was determined by combining a couple of simple tests with powerful techniques of surface and structure analysis. Results clearly proved that the effect of grinding on cotton fiber was much less severe than on linen. For both fibers, the degree of polymerization reduced (by 14.5% and 30.5% for cotton and linen, respectively) with a simultaneous increase in copper number. The increased water sorption capacity of the ground substrates was in good agreement with the X-ray results, which proved a less perfect crystalline structure in the ground samples. Data from XPS and SEM-EDS methods revealed that the concentration of oxygen atoms (bonded especially in acetal and/or carbonyl groups) on the ground surfaces increased significantly, resulting in an increase in oxygen/carbon atomic ratio (XPS data: from 0.11 to 0.14 and from 0.16 to 0.29 for cotton and linen, respectively). Although grinding created new surfaces rich in O atoms, the probable higher energy of the surface could not be measured by IGC, most likely due to the limited adsorption of the n-alkane probes on the less perfect crystalline surfaces.     

Effect of surface oxyfluorination on the dyeability of polyethylene film

The effect of surface oxyfluorination on low-density polyethylene (LDPE) film was studied in terms of surface functionality and surface energetics of the film surfaces, which can be attributed to improvement of the dyeability. The growth of functional groups and surface free energy was confirmed by FTIR-ATR, XPS, and contact angle methods. As a result, the total surface free energy was increased with oxyfluorination time, as a progressive increase of the polar component together with a small decrease of the dispersive component of surface free energy. From the dyeability test using the Kubelka-Munk equation, it was found that the oxyfluorination treatment plays an important role in the growth of oxygen-containing functional groups of LDPE film, resulting in improving the dyeability with a basic dyeing agent. A direct linear relationship is shown between the specific component of surface free energy and the K/S value for this work.     

On the indirect polyelectrolyte titration of cellulosic fibers. Conditions for charge stoichiometry and comparison with ESCA

The effect of electrolyte (NaHCO3) concentration on the adsorption of poly-DADMAC (poly-diallyldimethylammonium chloride) onto cellulosic fibers with different charge profiles was investigated. Surface carboxymethylated fibers were obtained by grafting carboxymethyl cellulose (CMC) onto the fiber surface and bulk carboxymethylated fibers were obtained by reacting the fibers with monochloroacetic acid. It was shown that nonionic interactions do not exist between cellulose and poly-DADMAC, rather electrostatic interactions govern the adsorption. Charge stoichiometry prevails under electrolyte-free conditions, whereas surface charge overcompensation occurs at higher electrolyte concentrations. It was shown that charge stoichiometry prevails if the thickness of the electric double layer kappa(-1) was larger than the mean distance between the charges on the fiber surface, as predicted by polyelectrolyte adsorption theories, taking lateral correlation effects into account. In a second set of experiments the ESCA technique served to independently calibrate the polyelectrolyte titrations for determining the surface charge of cellulosic fibers. Various molecular masses of poly-DADMAC were adsorbed to carboxymethylated fibers having different charge profiles. The adsorption of low M(w) poly-DADMAC (7.0 x 10(3)), analyzed by polyelectrolyte titration, was about 10 times higher than that of the high M(w) poly-DADMAC (9.2 x 10(5)). Despite the difference in accessibility of these two polyelectrolytes to the fiber cell wall, ESCA surface analysis showed, as expected, only slight differences between the two polyelectrolytes. This gives strong credibility to the idea that surface charge content of cellulosic fibers can be analyzed by means of adsorption of a high-molecular-mass cationic polymer, i.e., by polyelectrolyte titration.     

Water Accessibilities of Man-made Cellulosic Fibers – Effects of Fiber Characteristics

The dynamic vapor water sorption and desorption experiments were performed on cellulosic fibers with different characteristics. The hysteresis between moisture sorption and desorption cycle at 10% relative humidity (RH) was independent on the total moisture regain and approximately 45% for all materials except for viscose fibers. Brunauer–Emmett–Teller surface volume (V_m) for moisture sorption and retention capacity of liquid water (WRV) were also measured. The V_m and WRV increase in proportion to the total amount of moisture sorption (M_inf(total)) in all specimen except in poplar fiber. The coefficients of parallel exponential kinetics (PEK) were estimated by the curve-fitting of experimental data of the moisture regain, and the influences of the fiber characteristics on the PEK coefficients, the moisture regain, the hysteresis, V_m and WRV are discussed. The total equilibrium moisture content in the viscose fibers was higher but the moisture uptake and release rate was slower than the lyocell and poplar fibers. The cationization and the modification of shape of cross section accelerated the total equilibrium moisture content in the viscose fiber. A drying process at low temperature enhanced both the equilibrium moisture content and the moisture uptake and release rate in lyocell fibers while a spin finish retarded them. The total equilibrium moisture content was heightened by the crosslinking of the fiber, however, no obvious effect of the crosslinking on the moisture uptake and release rate was found. Effects of the type of the specimen and linear density on the moisture accessibilities are also discussed.     

Removal of U(VI) from aqueous solutions by using MWCNTs and chitosan modified MWCNTs

In this paper, the multiwalled carbon nanotubes (MWCNTs) were modified with chitosan (CS) by using low temperature plasma grafting technique (denoted as MWCNT-CS). The prepared MWCNTs and MWCNT-CS were characterized by SEM, TEM, FTIR and Raman spectroscopy in detail and the results suggested that CS molecules were successfully grafted on the surfaces of MWCNTs. The materials were applied as adsorbents in the removal of U(VI) ions from large volumes of aqueous solutions as a function of environmental conditions. The removal of U(VI) from aqueous solution to MWCNTs and MWCNT-CS increased with increasing pH values at pH < 7, and then decreased with increasing pH values at pH > 7. The sorption of U(VI) on MWCNTs and MWCNT-CS was strongly dependent on pH and independent of ionic strength. The sorption of U(VI) on MWCNTs and MWCNT-CS was dominated by inner-sphere surface complexation rather than by ion exchange or outer-sphere surface complexation. The surface grafted chitosan molecules can enhances U(VI) sorption on MWCNTs obviously, which was also evidenced from the XPS spectroscopy analysis. The results of high sorption capacity of U(VI) on MWCNT-CS suggest that the MWCNT-CS nanomaterial is a suitable candidate in the preconcentration of U(VI) ions from large volumes of aqueous solutions.     

Incorporation into paper of cellulose triacetate films containing semiconductor nanoparticles

CdSe/ZnS quantum dots (QDs) were embedded in films of cellulose triacetate (CTA) to give clear films with the broad absorbance and well-defined, size-tunable fluorescence characteristic of QDs. The relative quantum yields of the QDs in polymer were compared to that of the initial QDs dispersed in toluene. Alkaline hydrolysis of the film surfaces to regenerated cellulose rendered the previously hydrophobic CTA film surfaces hydrophilic and compatible with aqueous papermaking. Films containing combinations of different sized QDs gave more complex emission patterns. Small pieces of fluorescent films were added to pulp slurries and incorporated into laboratory paper sheets through hydrogen bonding between the regenerated cellulose film surfaces and cellulosic pulp fibers. The film system (cellulose ester bulk/cellulose surface) can be used to incorporate hydrophobic particles or molecules compatible with solutions of cellulosic polymers into paper products at both high and low loadings. QDs in paper may prove useful for security applications, such as sheets with unique optical signatures.     

Non-bonded organo-mineral interactions and sorption of organic compounds on soil surfaces: a model approach

Molecular mechanics and molecular dynamics calculations have been performed on organo-mineral composites that model the sorption of high-molecular-weight humic polymers on mineral surfaces and the sorption of low-molecular-weight organic contaminants on both mineral and organic surfaces in soil. Muscovite mica was chosen as a mineral model; an oxidized topological lignin-carbohydrate complex was chosen as a humic model; benzene, sodium benzoate, atrazine, and DDT represent different classes of contaminants. Sorption energies were estimated based on molecular mechanics calculations. Flexible linear polymers undergo drastic conformational changes when approaching the mineral surface, to ensure a gain in the interaction energy that outweighs a loss in the conformational energy proper. Therefore, the gas-phase conformation composi tion of environmental organic polymers is not directly related to their spatial organization in soil composites. Molecular dynamics simulation suggests high stability of the organic polymer coatings of mineral surfaces in the environment. Low-molecular-weight organic molecules demonstrate much less affinity for the mineral surface, which implies unhindered exchanges between the surface and its near environment. Ionizable compounds, e.g. salts of organic acids, are different, because they can form strong associations with a mineral surface through cation bridges. Sorption energies are compound-specific and depend on the sorbate-sorbent orientation. The calculations suggest some preference for the edges of a model muscovite sheet in comparison with the basal oxygen surface as a sorption site. Coating of mineral surfaces with organic polymers does not hinder the sorption of organic molecules except in the special case of organic ions.     

亚甲基蓝在云母表面吸附状态的研究

利用XPS测定吸附前后亚甲基蓝（MB）各原子的电子结合能的变化,以判断原子化学环境的改变,从而确定MB在云母表面的吸附位点是二甲胺基上的氮原子.通过AFM测量得到吸附于云母表面的MB分子的平均高度为0.820 nm,这证实了Hähner吸附模型的正确性,即MB分子的最大横截面以65～70°倾斜在云母的（001）表面上.     

Treatment in Swelling Solutions Modifying Cellulose Fiber Reactivity – Part 1: Accessibility and Sorption

Of prime importance in reactions involving insoluble cellulosic fibers is the sorption of reagents, which is governed by their degrees of accessibility in substrates. Swelling treatments of cellulosics in alkali solutions alter substrate accessibility leading to changes in their reactivity. In this paper, the first of a two-part series, we collate and examine the results from various studies involving different techniques to characterize modifications in cellulosic fibers after swelling treatments in alkali solutions. Results from measurements of structure and accessibility in fibers with techniques such as water retention, inverse size exclusion chromatography (ISEC), iodine sorption, fiber diameters, and fiber-splitting propensities indicate that the influence of swelling treatments on fiber structure/accessibility is differs with alkali type. The results show that a non-uniform rather than uniform distribution of reagents within structures is a more accurate representation of reactions involving swollen cellulosic fibers. Hence, the observed changes in cellulose-fiber reactivity are governed by the degrees of fiber swelling, and reagent sorption and accessibility during swelling treatments.     

Physicochemical properties of chemically and enzymatically modified cellulosic surfaces

Surface characteristics of modified cotton fibers have been studied using electrokinetic analysis (EKA), inverse gas chromatography (IGC) and dynamic contact angle (DCA) determinations. Modifications of cotton surfaces included mercerization, water-proofing, cross-linking, dyeing with a bifunctional reactive dye and cellulase biopolishing. Comparisons are made to linen as an example of a natural cellulosic fiber other than cotton and to rayon as a representative of a regenerated cellulosic fiber. Generally all cellulosic surfaces were bipolar with a slightly higher acidic contribution in the case of the cotton samples. EKA indicated ion dissociation as the predominant mechanism for surface charge in aqueous medium for all cellulosic samples, with the exception of greige cotton and the cotton sample with the hydrophobic finish. Results from EKA and IGC showed good correlation, while DCA yielded unreasonably high basic contributions most likely due to fiber swelling.     

Superhydrophobic surface fabricated by bulk photografting of acrylic acid onto high-density polyethylene

A superhydrophobic polymeric surface was prepared through a very simple bulk photografting method. A thin layer of acrylic acid (AA), a highly hydrophilic monomer, was sandwiched between two high-density polyethylene (HDPE) sheets, followed by UV irradiation for a short time, and then the two sheets were pulled apart and dried. The contact angles on the two grafted surfaces decreased very quickly with irradiation time in the first several seconds, and then increased with irradiation time to a level higher than that on pristine HDPE surface. When using a scraped PE surface as the bottom one, it showed superhydrophobicity after 35 s irradiation. XPS investigations show that strong rearrangement of the poly(acrylic acid) molecules has taken place on both surfaces, especially on the bottom surface, which provides the low surface free energy. The scraping and the grafting process led to the formation a unique micro- and nanostructure on the surface. These two factors lead to the superhydrophobicity. The as-prepared surface possesses superhydrophobic properties in a wide range of pH values, stimuli-responsive properties and low or very high adhesion under different situations.     

Surface modification of TiO2 nanoparticles with AHAPS aminosilane: distinction between physisorption and chemisorption

This paper addresses the surface modification of TiO₂ nanoparticles with n-(6-aminohexyl)aminopropyltrimethoxysilane (AHAPS) using various initial aminosilane concentrations. The main objective of this article is to show experimentally the importance of the physisorption during the grafting process. The distinction between chemisorbed and physisorbed aminosilane molecules on TiO₂ is thoroughly analyzed. The surface of bare and modified TiO₂ particles has been characterized by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) to gain a better understanding of the adsorption mechanism of AHAPS on TiO₂. Quantitative information on surface energy of TiO₂, in terms of adsorption energy sites and heterogeneity, has been investigated by quasi-equilibrium low-pressure adsorption technique using nitrogen and argon as probe molecules. The FTIR and XPS data are combined to estimate and discuss the chemisorbed and physisorbed contribution. The results demonstrate that both physisorption and chemisorption occurs but they display a different behavior. The physisorbed amounts are much higher than the chemisorbed amounts. This shows that the main part of the adsorbed layer is composed of physisorbed molecules. The physisorbed uptake depends highly on the AHAPS concentration while the chemisorbed amount remains constant. Quasi-equilibrium Ar derivative adsorption isotherms reveal that the AHAPS molecules are mostly located on the {101} and {001} faces of titania and that the two faces display the same reactivity toward AHAPS sorption. Nitrogen adsorption experiments show that the sorption takes place on the three polar surface sites of high energy. The molecules are chemisorbed onto the site displaying the highest energy while they are physisorbed on the two lower energy sites.     

MOLECULAR ENGINEERING STUDIES ON NONTHROMBOGENIC BIOMATERIALS--A NOVEL CLASS OF NONTHROMBOGENIC BIOMATERIALS WITH ZWITTERIONIC STRUCTURE OF CARBOXYBETAINES

N,N-dimethyl-N-methacryloyloxyethyl-N-carboxyethyl ammonium (DMMCA) was graft-copolymerized onto the surface of segmented poly(ether urethane) (SPEU) and PE film. The carboxybetaine structure on SPEU and PE film surfaces was confirmed by ATR-FTIR, XPS and water contact angle measurements. Through the experiments with platelet adhesion and protein adhesion assay in vitro, the two materials studied, including poly-DMMCA gel, all show excellent nonthrombogenicity. This confirms once again that the zwitterionic molecular structure on the surfaces of materials is essential for improving their nonthrombogenicity and biocompatibility.     

Effect of the corona treatment and of the 1,4-cyclohexanedimethanol on the surface characteristics of the poly(ethylene terephthalate) film

Several techniques have been applied for the characterization of three PET films surfaces: homopolymer PET film, corona treated PET film and a poly(ethylene terephthalate-co-1,4-cyclohexanedimethanol) film. The objective of this work is to investigate and to apply precise and mutually complementary techniques which give detailled information about theses surfaces, as there are few papers with global and conclusive results. The film surfaces were investigated to support the development of new products and envisage new apllications to the existent films. Scanning electron micrographs, attenuated total reflection Fourier transform infrared spectroscopy (FTIR-ATR) and multiple internal reflection Fourier transform infrared spectroscopy (FTIR-MIR) spectra show that the chemical composition, topography and surface roughness of the films are different. The corona-treated PET film shows high surface tension value due to the major contribution on the polar groups and oxidation level acquired. The copolyester film is much less crystalline than the other films analyzed, as demonstrated by refractive index measurements and X-ray photoelectron spectroscopy (XPS). The amorphous structures obtained and the high tension level of the corona-treated films provide a better understanding of the adhesion phenomena. In view of results obtained, one can assume that corona treated films owing to its higher surface tension and films with CHDM owing to its surface amorphization should provide manufacturing industries better processing conditions than films without surface treatment and also higher levels of adhesion to paints and coatings.     

Role of surface heterogeneity and molecular interactions in the charge-transfer process through self-assembled thiolate monolayers on Au(111)

A comparative study of charge-transfer processes from/to methyl-terminated and carboxylate-terminated thiolate-covered Au(111) surfaces to/from immobilized methylene blue (MB) molecules is presented. Scanning tunneling microscopy images with molecular resolution reveal the presence of molecular-sized defects, missing rows, and crystalline domains with different tilts that turn the thickness of the alkanethiolate SAM (the spacer) uncertain. The degree of surface heterogeneity at the SAMs increases as the number of C units (n) in the hydrocarbon chain decreases from n = 6. Defective regions act as preferred paths for MB incorporation into the methyl-terminated SAMs, driven by hydrophobic forces. The presence of negative-charged terminal groups at the SAMs reduces the number of molecules that can be incorporated, immobilizing them at the outer plane of the monolayer. Only MB molecules incorporated into the SAMs close to the Au(111) surface (at a distance < 0.5 nm) are electrochemically active. MB molecules trapped in different defects explain the broad shape and humps observed in the voltammogram of the redox couple. The heterogeneous charge-transfer rate constants for MB immobilized into methyl-terminated thiolate SAMs are higher than those estimated for carboxylate- terminated SAMs, suggesting a different orientation of the immobilized molecule in the thiolate environment.     

羊毛表面改性对拒水拒油整理的作用及机理研究

应用扫描电镜(SEM)、X射线光电子能谱(XPS)和衰减全反射红外光谱(FTIR-ATR)等现代表面分析技术研究不同改性处理羊毛表面的化学和物理结构特性.SEM研究结果表明,经低温等离子体表面改性或特定化学改性后的羊毛鳞片表面呈现纳米尺度的沟槽和凹凸结构,应用Wenzel公式和Cassie and Baxter公式阐述了表面粗糙度与接触角的关系,揭示了羊毛表面改性对于提高拒水拒油整理效果的原因所在.XPS和FTIR-ATR研究表明,上述物理和化学的表面改性技术使羊毛表面的二硫键氧化断裂和表面类脂物质改性/除去,促进拒水拒油整理剂的吸附和固着.表面改性和拒水拒油整理的协同效应赋予羊毛类荷叶效应,使其呈现超级拒水拒油拒污功能.     

Formation of molecular monolayers on TiO2 surfaces: a surface analogue of the Williamson ether synthesis

Strategies to modify metal oxide surfaces are important because of the increasing applications of metal oxides in catalysis, sensing, electronics, and renewable energy. Here, we report the formation of molecular monolayers on anatase nanocrystalline TiO(2) surfaces at near-ambient temperatures by a simple one-step immersion. This is achieved by an analogue of the Williamson ether synthesis, in which the hydroxyl groups of the TiO(2) surface react with iodo-alkane molecules to release HI and form a Ti-O-C surface linkage. The grafted molecules were characterized by Fourier-transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) to confirm the formation of covalently bonded monolayers. Kinetic studies yielded an activation barrier of ～59 kJ/mol for the grafting reaction. Measurements of hydrolytic stability of the grafted molecules in water show that approximately half the molecules are removed within minutes to hours at temperatures of 25-100 °C with an activation energy of ～82 kJ/mol, while the remaining molecules are stable for much longer periods of time. These different stabilities are discussed in terms of the different types of Ti-O-C bonds that can form on TiO(2) surfaces.