Synthesis and catalytic properties of barium hexaaluminates incorporated with chromium and lanthanum

Summary Barium hexaaluminates incorporated with chromium and lanthanum (Ba_1-xLa_xCrAl₁₁O_19-a) were synthesized from aqueous metal nitrates and sulfates through the precipitation, and then followed by crystallization at 1300^oC for 2 h. They had the ability to maintain heat resistance and high conversion of CH₄in methane combustion at elevated temperature.     

Catalytic combustion of methane over iron- and manganese-substituted lanthanum hexaaluminates

A series of hexaaluminates, LaMnFe _x Al_11−x O_19−δ samples (x = 1, 2, 4, 6, 8) as new catalysts were prepared by carbonate precipitation and calcined at high temperature. Fe and Mn ions were used as active components to replace part of aluminum ions in the hexaaluminate lattices. The structures and properties of these samples were characterized by XRD, BET, and XPS. The series of hexaaluminates exhibited significant catalytic activity and stability at high temperature. The LaMnFe₂Al₉O_19−δ retains a larger surface area and shows a good activity in methane combustion.     

Effect of acid-base properties on copper catalysts for hydrogenation of carbon dioxide

Acidic or basic components as co-catalysts were added to the Cu-based catalysts for hydrogenation of CO₂. Effects of acid-base properties on the catalytic activity and methanol selectivity are discussed.     

Control of the directions of oxidative transformation of methane over nickel-based catalysts by acid-base properties

Two completely different directions of the oxidative transformation of methane (OTM) were performed on nickel-based catalysts due to the different acid-base properties of those catalysts. The relatively acidic LaNiO_x and LiNiLaO_x/Al₂O₃ catalysts exhibit excellent Partial Oxidation of Methane to Syngas (POM) performance. However, the relatively basic LiNiLaO_x catalyst has a good Oxidative Coupling of Methane to C₂ Hydrocarbons (OCM) activity. The basic properties of the catalyst makes it difficult to reduce nickel and keeps it in the oxidized state. Reduced nickel is necessary for POM and oxidized nickel for the OCM reaction.     

Changes in the acid-base properties of hydrogels of metal oxide hydroxides induced by aging in solutions of electrolytes

Changes in the acid-base properties of titanium(IV), zirconium(IV), iron(III), chromium(III), and indium(III) hydrogels of oxide hydroxides induced by aging in sodium chloride and sulfate solutions were studied by the point of zero charge method. On aging in a solution of the sulfate electrolyte the hydrogels loose their basic properties much more rapidly than in the chloride solution. The most changes were observed in the region of high pH of the point of zero charge of the hydrogels. The changes in the acid-base properties can be explained by a decrease in the content of surface OH groups with are displaced by the supporting electrolyte ions, and due to the oxolation of the hydrogels. Published inIzvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1329–1332, August, 2000.     

Evaluation of acid-base properties of ammonia plasma-treated polypropylene by means of XPS

Acid-base properties of ammonia plasma-treated polypropylene (APTPP) were characterized by X-ray photoelectron spectroscopy (XPS) in conjunction with the molecular probe technique and using chloroform (TCM) as a reference Lewis acid. It is shown that TCM is retained by the basic surfaces of APTPP but not by the untreated PP. The retention of TCM is shown to be entirely due to the formation of TCM:APTPP acid-base complexes. This is supported by the C12p^3/2 binding energy (BE) and the shape of the Cl2p peak from the adsorbed TCM. ΔH^AB, the heat of TCM:APTPP acid-base interaction was found to be in the range of 3.1–4.3 kcal/mol using a published Cl2p^3/2 BE−ΔH^AB correlation. This ΔH^AB compares remarkably well with the values of 4.3–4.9 kcal/mol determined for TCM:amine complexes, and shows indeed that TCM is complexed by nitrogen containing basic groups grafted at the surface. However, the TCM/N ratio has an optimal value up to 1 second of plasma treatment and then decreases sharply, showing that less specific interaction sites are accessible at the surface for longer treatment times. This parallels previous findings about the metallization of APTPP by aluminium which was found to be optimal for treatment times lower than 1 second in our experimental conditions. This work shows that XPS can now indeed be used to quantitatively assess the acid-base properties of modified polymer surfaces.     

Acid-base properties of alumina prepared from a hydrated product of centrifugal thermal activation of hydrargillite (cta-product)

Summary Acid-base properties of aluminas prepared by thermal treatment of a hydrated CTA-product at 600°C were studied. The CTA-oxides, representing γ-Al₂O₃, were shown to contain terminal and bridged OH-groups. The concentration of the terminal OH-groups in the CTA-oxides was found to exceed their concentration in γ-Al₂O₃ prepared by dehydration of the “precipitated” pseudoboehmite, whereas the concentration of the bridged OH-groups in the CTA-oxides was lower than that in γ-Al₂O₃ prepared from pseudoboehmite. The total concentration of the surface Lewis acid sites in CTA-oxides varies within the limits of 2.80-4.14 mmol/m² and is essentially above that in g-Al₂O₃ (2.25 mmol/m²). The distinctive feature of the CTA-oxides is that their surface contains strong Lewis acid sites with n_CO = 2220 and 2238 cm^-1. The total concentration of basic sites in the CTA-oxides is lower than that in g-Al₂O₃, however, in contrast to g-Al₂O₃,they contain strong basic sites with n_CDCl3 = 2200 cm^-1.     

The influence of ionic surfactants on the acid-base properties and tautomeric equilibrium of 2-dimethylaminomethylphenol

Shifts in the acid-base and tautomeric equilibria have been observed in aqueous solutions of 2-dimethylaminomethylphenol (DAMP) containing surfactants. Cationic micelles of cetyltrimethylammonium bromide increase the dissociation constants of DAMP (pK₁ 0.3, pK₂ 0.5), and anionic micelles of sodium dodecyl sulfate reduce them (pK₁ 1.5, pK₂ 0.3). The constant of tautomeric equilibrium decreases when ionic surfactants are added. This is connected with the better solubilization of the neutral form by micelles.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 7, pp. 1215–1218, July, 1994.     

Structural characterization of a completely alkyl-substituted Al-Sb Lewis acid-base adduct

The Lewis acid-base adduct t-Bu₃Al-SbMe₃ (1), which was synthesized by reaction of equimolar amounts of t-Bu₃Al and trimethylstibine SbMe₃, was characterized by multinuclear NMR (¹H, ¹³C) spectroscopy, elemental analyses as well as by single crystal X-ray diffraction.     

Potentiometric and spectrophotometric study of the acid-base equilibria of Cr(VI) at 25°C and different ionic strengths of aqueous KNO3

The hydrolysis of the chromate ion has been studied using a potentiometric-spectrophotometric automated titration system, titrating basic K₂CrO₄–KNO₃ solutions with previously standarized HNO₃–KNO₃ solutions. The temperature was kept constant at 25°C and the ionic strengths were 0.5, 1.0 and 2.0 mol-dm^–3. The resulting titration curves can be interpreted in terms of two equilibria involving the formation of HCrO ₄ ^– (aq) and Cr₂O ₇ ^2– (aq). A spectrophotometric batch study was also carried out in order to obtain the thermodynamic constant for the HCrO ₄ ^– (aq) formation as well as the spectrophotometric parameters at low ionic strengths. The proposed stoichiometric constants for the two reactions and the molar absorptivities for the three species at different wavelengths and ionic strengths are also given.     

软硬酸碱理论与元素的存在形式

在无机化学元素部分教学中,元素的存在形式既是该元素化学性质的重要组成部分,又决定了元素单质和化合物的制备与合成方法。运用离子的电子结构知识及化学基本原理分析元素在自然界中的存在形式,既可以加深学生对化学基本知识和基本原理的理解,又可以将元素知识形成知识链以减少记忆量。本文利用软硬酸碱理论和地球环境的基本状况来分析元素在自然界的存在形式,得到了与实际较为符合的结果,表明这是一种简单实用的思路和方法。     

零流电位法在酸碱滴定中的应用研究

探讨了零流电位法在酸碱滴定中的检测原理及应用,通过考察强碱滴定弱酸、强碱滴定强酸、强酸滴定弱碱以及强酸滴定强碱四种滴定体系,探明了零流电位法在酸碱滴定中的适用性。通过氢氧化钠滴定醋酸对本方法进行评价,实验结果表明:本法的相对误差为-0.4%,同一根电极的滴定值的相对标准偏差(RSD)为0.4%(n=5),同一根电极五天滴定值的RSD为0.6%,五根电极滴定值的RSD为0.5%。本方法具有较高的准确性、稳定性和重现性。     

Structure of aminonitrones and electronic effect of substituents on their acid-base properties

A series of para-substituted aromatic aminonitrones p-RC₆H₄C(NH₂)=N⁺(Me)O^– (R = NMe₂, H, Br, Cl, CF₃) have been prepared. Acidity constants of the conjugate acids RC₆H₄C(NH₂)N⁺(Me)OH at 25°C in a EtOH–H₂O mixture (5: 95) have been determined by potentiometric titration. A linear correlation between log (k_R/k_H) and σ_para values has been revealed, and a ρ²⁹⁸(σ_para) parameter has been determined as of 0.635.     

Analyzing the surface properties of acrylic-based water-soluble polymers

The surface properties of newly synthesized N-methoxy isopropyl acrylamide, N-methoxy isopropyl methacrylamide, cyclo propyl acrylamide, and cyclo propyl methacrylamide polymers were investigated using inverse gas chromatography. The highest dispersive component of the surface energy value was obtained for cyclo propyl methacrylamide at 30°C. The values obtained for all polymers were decreasing with the increasing temperature. The values obtained for the acidic and the basic parameters revealed strong basic characters for the surface of N-methoxy isopropyl methacrylamide and cyclo propyl methacrylamide polymers and weak basic characters for the surface of N-methoxy isopropyl acrylamide and cyclo propyl acrylamide polymers.     

Effect of metal ions on structural,morphological and optical properties of nano-crystallite spinel cobalt-aluminate (CoAl2O4)

The bright blue nano crystallite cobalt aluminate (CoAl₂O₄) was synthesized by sol–gel method using a mixture of chelating agent of glycerol and citric acid. The effects of changing (0.05, 0.075, 0.10, 0.25, 0.50, and 0.75 mol/L) metal ion concentration on the structural, morphological and color properties of synthesized CoAl₂O₄ were characterized by using X-ray diffraction (XRD), Scanning electron microscopy (SEM), Energy dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), Nanoparticle size analyzer, Simultaneous Thermal Analyzer (STA), UV–vis absorption spectroscopy, and CIE-LAB colorimetric analysis. From the X-ray peak profile analysis, the crystallite size was measured by Debye-Scherrer (D-S) equation, and three different models presenting average crystallite sizes between 88.3 and 125.4 nm.The average lattice strain, dislocation density, lattice constant, cell volume, and zeta potential were between 0.00021 and 0.0058, (1.73 to 12.8) × 10¹⁴ (lines/m²), 8.10658 to 8.11181 Å, 533.60 to 533.81 Å³, ?56.4 to ? 63.5 mV, respectively. Using UV–vis absorption spectroscopy, the band gap was calculated from Kubelka-Munk method, and the values of band gap increasing from 1.82 to 1.84 eV, respectively. The reflectance spectra and the CIE-L*a*b* values of cobalt aluminate is also measured which confirmed the formation of blue nano crystallite cobalt aluminate.     

X-ray induced defects and thermoluminescent properties of lanthanum hexaaluminates with magnetoplumbite-like structure

This work presents an electron spin resonance and optical study of the defects produced by X-ray irradiation of the lanthanum aluminate La(Mg_1−yMn_y)_xAl₁₁O_18+x (x, y ≤ 1). The thermal bleaching of these defects is responsible for an intense green thermoluminescence due to the ⁴T₁-⁶A₁ transition of Mn²⁺ ions of the lattice. The mechanism of this thermoluminescence and its variation with manganese concentration are discussed.     

Lewis acid-base adducts of zwitterionic alkali metal methanides and silanides with BH3

The synthesis, structures and spectroscopic properties of M(MeOCH₂CH₂OMe₂Si)₃CBH₃ (M-1-BH₃) and M(MeOCH₂CH₂OMe₂Si)₃SiBH₃ (M-2-BH₃) (M?=?Li, Na, K) derived from reactions of BH₃ with the alkali metal zwitterions [M(MeOCH₂CH₂OMe₂Si)₃C] (M-1) and [M(MeOCH₂CH₂OMe₂Si)₃Si] (M-2) (M?=?Li, Na, K), resp., are reported. X-ray analysis and DFT calculations reveal discrete zwitterionic structures with the octahedral alkali metal cations rigidly locked and charge separated from the BH₃ units via pendant donors groups. Solution experiments with the hydride acceptors B(C₆F₅)₃ and [Ph₃C]₂[B₁₂C₁₂] indicate that Na-1-BH₃ can donate hydrides to form cations of formula [Na(MeOCH₂CH₂OMe₂Si)₃CBH₂]⁺.     

Spectrophotometric study of the acid-base equilibria of an imidazobenzodiazepine,midazolam, and its determination in pharmaceutical formulations

The acid-base behaviour of midazolam, a psychotropic drug derived from imidazobenzodiazepine family, has been studied spectro-photometrically. This compound hydrolyzes at pH values lower than 4. Reversible cleavage of the azomethine bond takes place and the open-ring compound is in equilibrium with the closed-ring compound (protonated form of the parent drug). Absorbance-time data (measured at 225 nm and for different pH values) have been evaluated by a pseudo-first order logarithmic approach, leading to different apparent kinetic constants, depending on pH and temperature. A simple mechanism of hydrolysis, corresponding to fast protonation and slow hydrolysis with opening of the ring is in good agreement with the kinetic results. From data obtained at pH values greater than 4, the deprotonation constant of the nitrogen atom at position 2 of the imidazole ring has been calculated and a pK_a value of 5.50 ± 0.05 obtained. In addition, a Spectrophotometric method has been developed which allows the determination of midazolam at concentrations from 1.23 × 10^–6 M to 3.38 × 10^–5 M. This method has been applied to a pharmaceutical formulation midazolam; the Dormicum error, in terms of relative standard deviation, was lower than 1.5%.     

Preparation and properties of aramid/layered silicate nanocomposites by solution intercalation technique

Polymer—clay nanocomposites were synthesized from aromatic polyamide and organoclay using the solution intercalation technique. Polyamide chains were produced through the reaction of 4,4′‐oxydianiline (ODA) and isophthaloyl chloride (IPC) in N, N′‐dimethyl acetamide, using stoichiometry yielding chains with carbonyl chloride end groups. The intercalation of sodium montmorillonite (Na‐MMT) was carried out using p‐phenylene diamine as a swelling agent through an ion exchange reaction. Different concentrations of organoclay were blended with the polyamide solution for complete dispersion of clay throughout the matrix. The resulting composite films were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), mechanical testing, thermogravimetry (TGA), differential scanning calorimetry (DSC) and water absorption measurements. The XRD pattern and morphology of the nanocomposites revealed the formation of exfoliated and intercalated clay platelets in the matrix. The film containing a small amount of clay was semitransparent and had a tensile strength of the order of 70 MPa (relative to the 52 MPa of the pure aramid). Thermal decomposition temperatures were in the range of 300–450°C and the weight of the samples remaining after heating to 900°C was found to be roughly proportional to the clay loading. DSC showed a systematic increase in the glass transition temperature with increase in clay content. Water absorption of the pristine aramid film was rather high (5.7%), which reduced upon loading of organoclay. Copyright © 2008 John Wiley & Sons, Ltd.     

Structural and electrical properties of Ca doped BiFeO3 multiferroic nanomaterials prepared by sol-gel auto-combustion method

Sol-gel auto combustion method was adopted for the synthesis of Bi_1-xCa_xFeO₃ (x = 0.00, 0.05, 0.1, 0.15, 0.2 and 0.25) multiferroic nanoparticles and their structural and electric properties were investigated. The two peaks at (012) and (110) planes at diffracting angles (2θ) of 31.9° and 32.1° in the XRD pattern indicates their rhombohedral structure with the R3c space group. The cole-cole plot in the 10 Hz–1 MHz frequency range shows the increasing semicircles shifting towards higher frequency, indicating increasing grain and grain boundaries.