Effects of matrix molecular weight on structure and reinforcement of high density polyethylene/mica composites

Three types of high-density polyethylene(HDPE)with different molecular weights(high,medium and low)were adopted to evaluate the influence of matrix molecular weight on the structure-property relation of injection-molded HDPE/mica composites through a combination of SEM,2d-WAXS,DSC,DMA and tensile testing.Various structural factors including orientation,filler dispersion,interfacial interaction between HDPE and mica,etc.,which can impact the macroscopic mechanics,were compared in detail among the three HDPE/mica composites.The transcrystallization of HDPE on the mica surface was observed and it exhibited strong matrix molecular weight dependence.Obvious transcrystalline structure was found in the composite with low molecular weight HDPE,whereas it was hard to be detected in the composites with increased HDPE molecular weight.The best reinforcement effect in the composite with low molecular weight HDPE can be understood as mainly due to substantially improved interfacial adhesion between matrix and mica filler,which arises from the transcrystallization mechanism.     

The interfacial enhancement of LLDPE/whisker composites via interfacial crystallization

Interfacial interaction plays a key role in the preparation of high performance polymer composites. In this work, in order to explore the possibility to enhance the interfacial interaction via interfacial crystallization of polymer matrix onto the filler surface, interfacial crystallization structure and mechanical properties of linear low density polyethylene (LLDPE)/whisker composites were investigated. The composites were firstly prepared by melt compounding, followed by processing in both traditional and dynamic injection molding. DSC, WAXD, SEM were used to characterize the interfacial crystallization structure. And the mechanical properties were measured by tensile testing. An imperfect shish‐calabash structure, with whisker served as shish, and irregular LLDPE spherulite as imperfect calabash, was formed during common injection molding processing. Such a structure was considered as the main reason for the strong interfacial adhesion and the obviously improved tensile strength and modulus. Furthermore, introducing shear could cause the formation of relatively perfect shish‐calabash structure, leading to the stronger interfacial adhesion. Copyright © 2011 John Wiley & Sons, Ltd.     

剪切作用下PA1010/PP共混物的形态与性能研究

通过动态保压注射成型方法制备了聚酰胺1010/聚丙烯(PA1010/PP)共混物,并研究了形态与性能的关系.力学性能测试结果表明在熔体冷却过程中施加剪切可以大大提高共混物的拉伸强度、拉伸模量和缺口冲击强度,当PP的质量分数为20%时,共混物的缺口冲击强度达到21.3kJ/m2,是静态样的3倍多,拉伸强度达到50.9MPa,是静态样的1.5倍.扫描电镜(SEM)结果表明在动态保压样的横断面可以观察到剪切诱导的形态,中间是芯层,围绕着芯层的是剪切层,最外面是皮层,相区尺寸显著减小、分散相分散更趋均匀,特别是PP的质量分数为20%时,相区尺寸从原来的约3.9μm降低到约1.4μm.动态保压样机械性能的提高归因于剪切作用下独特相形态的形成,分子链沿流动方向的取向是拉伸强度提高的主要原因,而剪切使分散相颗粒变小和剪切层中分子链的取向是冲击强度提高的主要原因.     

Oscillatory shear-accelerated exfoliation of graphite in polypropylene melt during injection molding

In this study, good dispersion status of graphite in a nonpolar, intractable polymer, i.e. polypropylene (PP), was realized in melt processing by using a specific dynamic packing injection molding (DPIM) technique. The exfoliation extent of graphite increased remarkably from the skin zone to the core zone of the molded part, as confirmed by combination of WAXD, SEM and TEM analyses, indicating an accelerated exfoliation occurred during the DPIM processing. This phenomenon is due to decreased melt flow channel and increased melt viscosity as the solidification takes place from the wall into the center, which leads to greatly increased shear force. The good dispersion of graphite results in obvious reinforcements of both tensile strength and impact strength by adding moderate amount of graphite. The present study proposes a promising route for realizing the large-scale fabrication of structural parts of polymer/exfoliated-graphite nanocomposites with excellent mechanical properties.     

聚烯烃共混物注射制品的形态控制与多层次结构

从注射制品形态控制和结构表征的角度探讨高分子材料加工-形态-性能之间的关系.研究中采用动态保压成型方法来制备注射样品,在注射成型过程中引入剪切应力场的作用,制得的样品表现出明显的多层次结构,从外向里分别为皮层、剪切层、芯层,表现出不同的相形态、结晶形貌以及取向行为.研究发现,剪切应力对聚烯烃的形态发展和结构变化具有重要影响.在剪切应力的作用下,聚烯烃共混物中分散相会发生变形、取向,从而导致共混物的相转变点发生移动;结晶形态从球晶转变为shish-kebab结构;聚烯烃共混物在高剪切应力下相容,低剪切下发生相分离;HDPE/PP共混物的注射制品中出现附生结晶等现象.     

The effect of surface coating of CNTs on the mechanical properties of CF‐filled HDPE composites

Mechanical properties of carbon fiber (CF) and carbon nanotube (CNT)‐filled thermoplastic high‐density polyethylene (HDPE) composites were studied with particular interest on the effects of filler content and fiber surface treatment by coupling agent. Surface‐treated CF‐filled HDPE composites increased their tensile strength and impact strength, which is further increased with the addition of CNT. SEM showed that CNT‐coating‐treated CF‐HDPE composites show better dispersion of the filler into the matrix, which results in better interfacial adhesion between the filler and the matrix. Copyright © 2014 John Wiley & Sons, Ltd.     

碳纳米管改性聚苯硫醚熔纺纤维的结构与性能研究

将多壁碳纳米管(MWCNTs)和聚苯硫醚(PPS)经过熔融挤出后制备成复合材料切片,并采用熔融纺丝法制得碳纳米管改性聚苯硫醚复合纤维.采用扫描电镜(SEM)、拉曼光谱、示差扫描量热分析(DSC)、动态机械分析(DMA)以及力学性能测试等表征手段研究了复合纤维中碳管的分散状态,与基体的界面作用,复合纤维的结晶性能以及力学性能,从而探讨了聚苯硫醚/碳纳米管复合纤维体系的微观结构与宏观性能之间的关系.研究表明,聚苯硫醚分子结构与碳纳米管之间具有的π-π共轭作用使碳管较为均匀的分散在基体中,界面结合较为紧密.同时熔融纺丝过程中的拉伸作用使碳管进一步解缠并使碳管沿纤维拉伸方向取向.另一方面,拉曼光谱显示拉伸作用有效地增强了界面作用,有利于外界应力的传递.碳管的良好分散以及强的界面作用使复合纤维力学性能得到大幅度的提高,当碳管含量达到5 wt%时,复合纤维的模量有了明显的提高,拉伸强度较纯PPS纤维提高了近220%.     

Comparison of the effect of mica and talc and chemical coupling on the rheology,morphology, and mechanical properties of polypropylene composites

The effect of filler types of mica and talc on the oscillatory shear rheological properties, mechanical performance, and morphology of the chemically coupled polypropylene composites is studied in this work. The Maleic Anhydride grafted Polypropylene (MAPP) was used as an adhesion promoter for coupling mineral particles with the polypropylene matrix. The samples were prepared by a co‐rotating, L/D = 40, 25 mm twin screw extruder. The tensile tests carried out on the injection molded samples showed a reinforcing effect of talc up to 20 wt% on the Polypropylene (PP). The tensile strength of PP‐mica composites showed a slight decrease at all percentages of mica. The effect of chemical coupling by using MAPP on the tensile strength was more pronounced in increasing the tensile strength for PP‐mica than PP‐talc composites. The complex viscosity curve of pure PP and the composites, showed a Newtonian plateau (η₀) up to 30 wt% at low frequency terminal zone. By increasing the filler content to 40 and 50 wt%, the complex viscosity at very low shear rates sharply increased and showed yield behavior that can be due to the formation of filler particles networks in the melt. At the optimum amount of coupling agent, a minimum in cross over frequency curve against MAPP content is observed. The optimum amount of coupling agent for PP‐talc composites is about 1.5%, and about 3% for PP‐mica formulations. The analysis of viscosity behavior at power‐law high region, revealed the more shear thinning effect of mica than talc on the PP matrix resin. Copyright © 2009 John Wiley & Sons, Ltd.     

Molecular orientation,crystallinity, and flexural modulus correlations in injection molded polypropylene/talc composites

In order to promote better understanding of the structure‐mechanical properties relationships of filled thermoplastic compounds, the molecular orientation and the degree of crystallinity of injection molded talc‐filled isotactic polypropylene (PP) composites were investigated by X‐ray pole figures and wide‐angle X‐ray diffraction (WAXD). The usual orientation of the filler particles, where the plate planes of talc particles are oriented parallel to the surface of injection molding and influence the orientation of the α‐PP crystallites was observed. The PP crystallites show bimodal orientation in which the c‐ and a*‐axes are mixed oriented to the longitudinal direction (LD) and the b‐axis is oriented to the normal direction (ND). It was found that the preferential b‐axis orientation of PP crystallites increases significantly in the presence of talc particles up to 20 wt% in the composites and then levels‐off at higher filler content. WAXD measurements of the degree of crystallinity through the thickness of injection molded PP/talc composites indicated an increasing gradient of PP matrix crystallinity content from the core to the skin layers of the molded plaques. Also, the bulk PP crystallinity content of the composites, as determined by DSC measurements, increased with talc filler concentration. The bulk crystallinity content of PP matrix and the orientation behavior of the matrix PP crystallites and that of the talc particles in composites are influenced by the presence of the filler content and these three composite's microstructure modification factors influence significantly the flexural moduli and the mechanical stiffness anisotropy data (E_LD/E_TD) of the analyzed PP/talc composites. Copyright © 2009 John Wiley & Sons, Ltd.     

Shear-induced change of phase morphology and tensile property in injection-molded bars of high-density polyethylene/polyoxymethylene blends

It is feasible to control the phase morphology and phase inversion for immiscible polymer blends to manipulate their properties. In this work, the blend of high-density polyethylene (HDPE)/polyoxymethylene (POM) was used as an example, to demonstrate the effect of shear on the phase morphology and resultant mechanical properties in immiscible polymer blends. To do so, a well defined “in-process morphology control” process during injection molding was conducted. That was: after making the blends via melt mixing, the injection-molded bars were prepared via a so-called dynamic packing injection molding equipment to impose a prolonged shearing on the melts during the solidification stage. Phase morphologies and crystal structures of the blends were estimated mainly through scanning electron microscopy, differential scanning calorimetry and 2D wide-angle X-ray scattering, respectively. For in-process morphology controlled samples, co-continuous structures, especially subinclusions inside another continuous phase induced by shear, were observed when the HDPE content was between 30 wt% and 50 wt%, leading to much early occurrence of phase inversion and also the lowest degree of orientation for both HDPE and POM. However, for samples obtained via conventional injection molding, a droplet morphology was always observed with HDPE dispersed in POM as the content of HDPE was up to 30 wt%, but with POM dispersed in HDPE as the content of HDPE was 50 wt%. The performances of injection-molded bars were mainly respect to the phase morphologies for samples obtained via conventional injection molding in which tensile properties continuously decreased with increasing of HDPE content up to 30 wt% and then increased with further increasing of HDPE content. For the in-process morphology controlled samples, the tensile properties depended not only on the phase morphology, but more importantly on the degree of orientation. One observed only a slight decrease of tensile property as the content of HDPE was less than 15 wt%, while an abrupt decrease when the content of HDPE was between 30 wt% and 50 wt%, probably due to the lowest degree of orientation in this composition range.     

Role of gas delay time on the hierarchical crystalline structure and mechanical property of HDPE molded by gas-assisted injection molding

The relationship among the processing parameters, crystalline morphology, and macroscopic properties in injected molded bar becomes very complicated due to existence of temperature gradient and shear gradient along the sample thickness. To enhance the shear strength, gas-assisted injection molding (GAIM) was utilized in producing the molded bars. The aim of our research was to explore the relationship between processing conditions and the spatial variation of the hierarchy structure as well as the mechanical properties of high-density polyethylene (HDPE) obtained via GAIM. In our previous work [Wang L, Yang B, Yang W et al (2011) Colloid Polym Sci 289:1661–1671], we found that the enhancement of the gas pressure can remarkably increase the degree of molecular orientation in the HDPE samples, which turns out to improve the mechanical performances of GAIM parts. In this work, the hierarchy structure, orientation behavior, and mechanical properties of molder bars under different gas delay time were investigated using a variety of characterization techniques including rheological experiments, scanning electron microscope, tensile testing, differential scanning calorimetry, and two-dimensional wide-angle X-ray scattering. Moreover, the temperature field during the short shot stage of GAIM process was simulated using an enthalpy transformation approach. Our results indicate that these properties were intimately related to each other, and with prolonged gas delay time, GAIM samples with higher degree of orientation and improved mechanical properties were obtained.     

EFFECT OF DISPERSION OF MICA IN MATRIX ON YOUNG''''S MODULUS OF MICA FILLED POLYETHYLENE

The correlation between Young's modulus of mica-filled high density polyethylene (HDPE), low density polyethylene(LDPE) and the state of dispersion of plasma-treated mica in the polymer matrices was studied. The modulus and the number average diameter of mica aggregates in matrix were determined with tensile testing and image analysis respectively. The interface structure of the filler/matrix and the bulk structure of matrix were examined through the dielectric spectrometry, differential scanning calorimetry (DSC) and dynamic viscoelastic spectrometry. The results show that the Young's modulus of the filial polyethylene depends to a great extent upon the state of dispersion of filler in matrix, but it is independent of the interface structure and bulk structure. The better the dispersion, the higher the Young's modulus.     

Hierarchical crystalline structures and dynamic mechanical properties of injection‐molded bars of HDPE: attributes of temperature field

The relationship among the processing parameters, crystalline morphologies and mechanical properties of injected‐molded bar becomes much complicated primarily due to the existence of temperature gradient coupled with the shear gradient along the sample thickness. The effect of thermal gradient field on the microstructural evolution, hierarchical structures and dynamic mechanical properties of high‐density polyethylene parts molded via gas‐assisted injection molding (GAIM) were investigated using scanning electron microscope, differential scanning calorimetry, dynamic mechanical analysis and two‐dimensional wide‐angle X‐ray diffraction. The three‐dimensional temperature profiles during the cooling stage under different melt temperatures of GAIM process were obtained by using a transient heat transfer model of the enthalpy transformation approach, and the phase‐change plateaus were clearly observed in the cooling curves. It was found that a variety of melt temperatures could induce considerable variations of the hierarchical structures, orientation behavior and dynamic mechanical properties of the injection‐molded bars. With reduced melt temperature, GAIM samples with higher molecular orientation and improved dynamic mechanical properties were obtained. Copyright © 2013 John Wiley & Sons, Ltd.     

The research on the mechanical properties improvement of HDPE/ABS blends reinforced with acid‐treated wood fiber

In this study, the effect of acid‐treated wood fiber modifications on the mechanical behaviors of HDPE/ABS blend is investigated. Wood fiber/HDPE/ABS composites were fabricated by incorporating acid‐treated wood fiber into HDPE/ABS blends. The results showed that both the tensile strength and flexural strength of wood fiber/HDPE/ABS composites were greater than those of HDPE/ABS blend, regardless of wood fiber modification. The results also showed that the impact strength of HDPE/ABS composites is improved by the addition of wood fiber. Scanning electron microscopic (SEM) examination of fractured surfaces showed that the improvement in the mechanical properties of the wood fiber/HDPE/ABS composites was attributed to the improved dispersion of wood fiber in the HDPE/ABS and the better interfacial characteristics caused by the acid treatment of the wood fiber.     

MECHANICAL PROPERTIES OF SMC WHISKER REINFORCED HIGH DENSITY POLYETHYLENE COMPOSITES

A new type of SiO_2-MgO-CaO (SMC) whisker was used to modify high density polyethylene (HDPE).The melting behavior and crystallinity were investigated by differential scanning calorimetry (DSC).The dispersion of whiskers and interfacial adhesion in the prepared HDPE/SMC whisker composites were investigated by scanning electron microscopy (SEM).The mechanical properties were evaluated by mechanical tests and dynamic mechanical analysis (DMA).DSC data indicated that the melting temperature and the crystall...     

Development of morphology and properties of injection‐molded bars of HDPE/PA6 blends along flow direction

The structure and mechanical properties of injection‐molded bars of high‐density polyethylene (HDPE)/PA6 blends were studied in this article. The experimental results showed that the morphologies of injection‐molded bars change gradually along the flow direction, which is tightly related to the melt viscosity and processing conditions. The higher melt viscosity, lower mold temperature, and shorter packing time, restricting the macromolecular relaxation, enhance the difference in morphologies and properties at near and far parts of a mold. An injection‐molded bar (namely H2C5), consisting of 75 wt % of HDPE, 20 wt % of PA6, and 5 wt % of compatibilizer (HDPE‐g‐MAH), showed a greater difference in mechanical properties at near and far parts because of its higher melt viscosity. A clear interface between the skin and core layers of near part in it leads to a much higher impact strength than that of far part. And tensile tests show that its tensile strength of near part is higher than that of far part due to the higher orientation degrees of HDPE matrix and PA6 dispersed phase in near part. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 184–195, 2007     

SPATIAL HIERARCHY AND INTERFACIAL STRUCTURE IN INJECTIONMOLDED BARS OF POLYPROPYLENE-BASED BLENDS AND COMPOSITES

The hierarchical structure and interfacial morphology of injection-molded bars of polypropylene （PP） based blends and composites have been investigated in detail from the skin to the core. For preparation of injection-molded bars with high-level orientation and good interfacial adhesion, a dynamic packing injection molding technology was applied to exert oscillatory shear on the melts during solidification stage. Depending on incorporated component, interfacial adhesion and processing conditions, various oriented structure and morphology could be obtained. First, we will elucidate the epitaxial behavior between PP and high-density polyethylene occurring in practical molded processing. Then, the shear-induced transcrystalline structure will be the main focus for PP/fiber composites. At last, various oriented clay structures have been ascertained unambiguously in PP/organoclay nanocomposites along the thickness of molded bars.     

SUPER POLYOLEFIN BLENDS ACHIEVED VIA DYNAMIC PACKING INJECTION MOLDING:MORPHOLOGY AND PROPERTIES

As a long-term project aimed at developing super polyolefin blends, in this paper we summarize our work on themechanical reinforcement and phase morphology of polyolefin blends achieved by dynamic packing injection molding(DPIM). The main feature of this technology is that the specimen is forced to move repeatedly in the model by two pistonsthat move reversibly with the same frequency during cooling, which results in preferential orientation of the dispersed phaseas well as the matrix. The typical morphology of samples obtained via DPIM is a shear-induced morphology with a core inthe center, an oriented zone surrounding the core and a skin layer in the cross-section areas. Shear-induced phase dissolutionat a higher shear rate but phase separation at low shear rates is evident from AFM examination of LLDPE/PP (50/50) blends.The super polyolefin blends having high modulus (1.9-2.2 GPa), high tensile strength (100-120 MPa) and high impactstrength (6 times as that of pure HDPE) have been prepared by controlling the phase separation, molecular orientation andcrystal morphology.     

Molecular weight dependence of hybrid shish kebab structure in injection molded bar of polyethylene/inorganic whisker composites

In our previous work, a hybrid shish kebab structure, with polyethylene (PE) crystal lamellae periodically decorated on the surface of an inorganic whisker (SMCW) and aligned approximately perpendicular to the long axis of the whisker, has been observed in the injection molded bar of PE/SMCW composites. To investigate the effect of the molecular weight of the PE matrix on the formation of the hybrid shish kebab structure and the corresponding physical properties of HDPE/SMCW composites, in this work, three types of PE with different molecular weights were used to prepare the composites. They were first melt blended and then subjected to dynamic packing injection molding (DPIM), in which the prolonged shear was exerted on the melt during the solidification stage. An obvious hybrid shish kebab (HSK) structure, with PE crystal lamellae closely packed on the surface of the SMCW, was found in the samples with a low molecular weight PE (LMW-PE) matrix and a medium molecular weight PE (MMW-PE) matrix. However, in samples with a high molecular weight PE (HMW-PE) matrix, an incomplete HSK structure with PE crystal lamellae loosely decorated on the surface of the SMCW was observed. Furthermore, DSC results indicated that SMCW served as a good nucleating agent only for the composite with a LMW-PE matrix and the nucleation efficiency decreased with increasing PE molecular weight. Correspondingly, the tensile strength of the PE/SMCW composites was significantly improved by adding SMCW for the samples with a LMW-PE or MMW-PE matrix. Especially for samples with a LMW-PE matrix, the tensile strength was remarkably enhanced by the presence of only 1 wt % SMCW. For the composites with a HMW-PE matrix, the addition of SMCW had almost no reinforcing effect on the composites. The molecular weight dependence of the formation of HSK and property enhancement was discussed on the basis of the chain mobility and crystallization capability of the PE matrix.     

在低频振动场中注射成型HDPE试样的力学性能及其形态控制

利用自行研制的低频振动注射实验装置探讨HDPE振动注射试样力学性能和微观形态之间的关系 .实验中对常规注射和振动注射成型的试样力学性能和微观形态进行了对比实验 .SEM实验结果显示 ,振动注射制件芯层的形态由常规注射的球晶转变为垂直于振动波传递方向排列的片晶结构 ,在剪切层中同时存在串晶或柱状堆砌的片晶结构 .频率的改变 (0 相似文献