Sorbent coatings for solid-phase microextraction based on mixtures of polymeric ionic liquids

Four polymeric ionic liquids based on two different cations, poly(1‐vinyl‐3‐hexylimidazolium) and poly(1‐vinyl‐3‐hexadecylimidazolium), combined with two different anions, bis[(trifluoromethyl)sulfonyl]imide (NTf) and chloride (Cl^?), were combined in various weight percentages and used as sorbent coatings for solid‐phase microextraction gas chromatography (SPME‐GC). The selectivity of the fiber coatings for 12 test analytes was examined. The extraction efficiency of n‐alcohols increased with an increase in the weight percentage of chloride ion in the sorbent coating. The ability to tune the interactions between the coating material and the analytes was exploited and resulted in distinct changes in the limits of detection for hydrogen‐bonding analytes with varying chloride ion content in the sorbent coating.     

Correlation of the Solubilizing Abilities of Hexyl(trimethyl)ammonium <Emphasis Type="Italic">bis</Emphasis>((Trifluoromethyl)sulfonyl)imide, 1-Propyl-1-methylpiperidinium <Emphasis Type="Italic">bis</Emphasis>((Trifluoromethyl)sulfonyl)imide,and 1-Butyl-1-methyl-pyrrolidinium Thiocyanate

Chromatographic retention data were measured for a wide range of organic solutes on 1-butyl-1-methylpyrrolidinium thiocyanate ([BMPyrr]⁺[SCN]⁻), hexyl(trimethyl)ammonium bis((trifluoromethyl)sulfonyl)imide ([HexM₃Am]⁺[(Tf)₂N]⁻), and 1-propyl-1-methylpiperidinium bis((trifluoromethyl)sulfonyl)imide ([PMPip]⁺[(Tf)₂N]⁻) stationary phases at 323 and 353 K. The measured retention factors were combined with published infinite dilution activity coefficient and gas-to-water partition coefficient data to yield gas-to-anhydrous ionic liquid (IL) partition coefficients and water-to-anhydrous IL partition coefficients. Both sets of partition coefficients were analyzed using the Abraham model. The derived Abraham model correlations describe the observed gas-to-IL and water-to-IL partition coefficient data to within average standard deviations of 0.116 and 0.156 log₁₀ units, respectively.     

Tuning the selectivity of polymeric ionic liquid sorbent coatings for the extraction of polycyclic aromatic hydrocarbons using solid-phase microextraction

A new generation polymeric ionic liquid (PIL), poly(1-4-vinylbenzyl)-3-hexadecylimidazolium bis[(trifluoromethyl)sulfonyl]imide (poly(VBHDIm⁺ NTf₂⁻)), was synthesized and is shown to exhibit impressive selectivity towards the extraction of 12 polycyclic aromatic hydrocarbons (PAHs) from aqueous samples when used as a sorbent coating in direct-immersion solid-phase microextraction (SPME) coupled to gas chromatography (GC). The PIL was imparted with aromatic character to enhance π–π interactions between the analytes and the sorbent coating. For comparison purposes, a PIL with similar structure but lacking the π–π interaction capability, poly(1-vinyl-3-hexadecylimidazolium bis[(trifluoromethyl)sulfonyl]imide) (poly(HDIm⁺ NTf₂⁻)), as well as a commercial polydimethylsiloxane (PDMS) sorbent coating were evaluated and exhibited much lower extraction efficiencies. Extraction parameters, including stir rate and extraction time, were studied and optimized. The detection limits of poly(VBHDIm⁺ NTf₂⁻), poly(HDIm⁺ NTf₂⁻), and PDMS coatings varied between 0.003–0.07 μg L⁻¹, 0.02–0.6 μg L⁻¹, and 0.1–6 μg L⁻¹, respectively. The partition coefficients (log K_fs) of eight PAHs to the three studied fiber coatings were estimated using a static SPME approach. This study represents the first report of analyte partition coefficients to any PIL-based material.     

Role of counteranions in polymeric ionic liquid-based solid-phase microextraction coatings for the selective extraction of polar compounds

A polymeric ionic liquid (PIL) poly(1-vinyl-3-hexylimidazolium chloride) (poly(ViHIm⁺Cl⁻)) was designed as a coating material for solid phase microextraction (SPME) to extract polar compounds including volatile fatty acids (VFAs) and alcohols. The extracted analytes were analyzed by using gas chromatography (GC) coupled with flame ionization detection (FID). Extraction parameters of the HS–SPME–GC–FID method, such as ionic strength, extraction temperature, pH and extraction time were optimized. Calibration studies were carried out under the optimized conditions to further evaluate the performance of the PIL-based SPME coating. For comparison purposes, the PIL poly(1-vinyl-3-hexylimidazolium bis[(trifluoromethyl)sulfonyl]imide) (poly(ViHIm⁺NTf₂⁻)) was also used as the SPME coating to extract the same analytes. The results showed that the poly(ViHIm⁺Cl⁻) PIL coating had higher selectivity towards more polar analytes due to the presence of the Cl⁻ anion which provides higher hydrogen bond basicity than the NTf₂⁻ anion. The limits of detection (LODs) determined by the designed poly(ViHIm⁺Cl⁻) PIL coating ranged from 0.02 μg L⁻¹ for octanoic acid and decanoic acid and 7.5 μg L⁻¹ for 2-nitrophenol, with precision values (as relative standard deviation) lower than 14%. The observed performance of the poly(ViHIm⁺Cl⁻) PIL coating was comparable to previously reported work in which commercial or novel materials were used as SPME coatings. The selectivity of the developed PIL coatings was also evaluated using heptane as the matrix solvent. This work demonstrates that the selectivity of PIL-based SPME coatings can be simply tuned by incorporating different counteranions to the sorbent coating.     

Isotope effects on miscibility of 1-alkyl-3-methylimidazolium bis(trifluoromethyl)sulfonyl imides with aromatic hydrocarbons

The liquid–liquid miscibility temperatures as a function of composition and deuterium substitution have been experimentally determined for the binary mixtures of 1-decyl-3-methylimidazolium bis(trifluoromethyl)sulfonyl imide, [C₁₀MIM][NTf₂], and 1-dodecyl-3-methylimidazolium bis(trifluoromethyl)sulfonyl imide, [C₁₂MIM][NTf₂] with benzene and toluene and their deuterated forms. All systems exhibit upper critical solution temperatures (UCSTs) and better miscibility for ionic liquids with longer alkyl chain. The interchange of benzene for toluene results in worse miscibility for [C₁₀MIM][NTf₂] and better for [C₁₂MIM][NTf₂]. Deuteration of the aromatics leads to better miscibility in each case. The sign of the isotope effect is in agreement with expectations and its value seems to be seriously affected by the neighborhood of the hypercritical state.     

Conductive polymeric ionic liquids for electroanalysis and solid-phase microextraction

Three novel electropolymerizable thiophene-based ionic liquids (ILs) were synthesized and characterized as potential candidates for developing selective extraction media for chemical analysis. Electropolymerization of the bis[(trifluoromethyl)sulfonyl]imide ([NTf₂]^-) analogs successfully produced uniform polymeric thin-films on macro- and microelectrode substrates from both vinyl and methylimidazolium IL monomer derivatives. The resultant conducting polymer IL (CPIL) films were characterized by electrochemical methods and found to exhibit attractive behavior towards anionic species while simultaneously providing an exclusion barrier toward cationic species. Thermogravimetric analysis of the thiophene-based IL monomers established a high thermal stability, particularly for the methylimidazolium IL, which was stable until temperatures above 350 °C. Subsequently, the methylimidazolium IL was polymerized on 125 μm platinum wires and utilized for the first time as a sorbent coating for headspace solid-phase microextraction (HS-SPME). The sorbent coating was easily prepared in a reproducible manner, provided high thermal stability, and allowed for the gas chromatographic analysis of polar analytes. The normalized response of the poly[thioph-C₆MIm][NTf₂]-based sorbent coating exhibited higher extraction efficiency compared to an 85 μm polyacrylate fiber and excellent fiber-to-fiber reproducibility. Therefore, the electropolymerizable thiophene-based ILs were found to be viable new materials for the preparation of sorbent coatings for HS-SPME.     

Synthesis,physical, and thermodynamic properties of 1-alkyl-cyanopyridinium bis{(trifluoromethyl)sulfonyl}imide ionic liquids

Synthesis of new ionic liquids (ILs) viz. 1-butyl-3-cyanopyridinium bis{(trifluoromethyl)sulfonyl}imide, [BCN³Py][NTf₂], 1-hexyl-3-cyanopyridinium bis{(trifluoromethyl)sulfonyl}imide, [HCN³Py][NTf₂], 1-hexyl-4-cyanopyridinium bis{(trifluoromethyl)sulfonyl}imide, [HCN⁴Py][NTf₂], and 1-octyl-3-cyanopyridinium bis{(trifluoromethyl)sulfonyl}imide, [OCN³Py][NTf₂] were performed. The specific basic characterization of new compounds by NMR spectra, elementary analysis, water content and glass transition temperature as well as melting temperature, enthalpy of fusion and decomposition of compounds TG/DTA determined by the differential scanning calorimetry, DSC is presented. The heat capacity was measured at three temperatures (298.15, 323.15, and 353.15) K and at pressure 0.1 MPa. The effect of temperature on the density and viscosity is reported over the temperature range from (293.15 to 363.15) K and at 0.1 MPa. The density and viscosity correlation for these systems was provided by an empirical polynomial. From the density–temperature dependence, the isothermal expansion coefficient (volume expansivity), α, was calculated. The surface tension of pure ionic liquids was measured at 0.1 MPa at five temperatures (298.15, 308.15, 318.15, 328.15, and 338.15) K. The surface thermodynamic functions such as surface entropy and enthalpy, critical temperatures according to the Eötvös and Guggenheim definition and the total surface energy of the ILs studied were derived from the temperature dependence of the surface tension values. The parachor and speed of sound for pure ionic liquids were described within a range of temperature from (298.15 to 338.15) K. A qualitative analysis on these quantities in terms of molecular interactions is reported.     

Synthesis and Characterisation of Fluorescent Carbon Nanodots Produced in Ionic Liquids by Laser Ablation

Carbon nanodots (C‐dots) with an average size of 1.5 and 3.0 nm were produced by laser ablation in different imidazolium ionic liquids (ILs), namely, 1‐n‐butyl‐3‐methylimidazolium tetrafluoroborate (BMI.BF₄), 1‐n‐butyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide (BMI.NTf₂) and 1‐n‐octyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)imide (OMI.NTf₂). The mean size of the nanoparticles is influenced by the imidazolium alkyl side chain but not by the nature of the anion. However, by varying the anion (BF₄ vs. NTf₂) it was possible to detect a significant modification of the fluorescence properties. The C‐dots are much probably stabilised by an electrostatic layer of the IL and this interaction has played an important role with regard to the formation, stabilisation and photoluminescence properties of the nanodots. A tuneable broadband fluorescence emission from the colloidal suspension was observed under ultraviolet/visible excitation with fluorescence lifetimes fitted by a multi‐exponential decay with average values around 7 ns.     

Synthesis of copolyimides based on room temperature ionic liquid diamines

Block copolyimides based on aromatic dianhydrides and diamines copolymerized with diamino room temperature ionic liquid (RTIL) monomers were synthesized over a range of compositions. Specifically, two diamino RTILs, 1,3‐di(3‐aminopropyl) imidazolium bis[(trifluoromethyl)sulfonyl] imide ([DAPIM] [NTf₂]) and 1,12‐di[3‐(3‐aminopropyl) imidazolium] dodecane bis[(trifluoromethyl) sulfonyl] imide ([C₁₂ (DAPIM)₂] [NTf₂]₂) were synthesized using a Boc protection method. The two RTILs were reacted with 2,2‐bis(3,4‐carboxylphenyl) hexafluoropropane dianhydride (6FDA) to produce 6FDA‐RTILs oligomers that formed the RTIL component for the block copolyimides. The oligomers were reacted with 6FDA and m‐phenylenediamine (MDA) at oligomer concentration from 6.5 to 25.8 mol % to form block copolyimides. Increasing the concentration of the 6FDA‐RTIL oligomer in the block copolyimides resulted in a decrease in the thermal degradation temperature, glass transition temperature and an increase in the density. The gas permeability of the RTIL based block copolyimide decreased but the ideal permeability selectivity for CO₂/CH₄ gas pair increased relative to the pure 6FDA‐MDA. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4036–4046, 2010     

High temperature and highly selective stationary phases of ionic liquid bonded polysiloxanes for gas chromatography

Due to the special performance of “dual nature” and synthetic flexibility, ionic liquids (ILs) have been an attractive research subject of stationary phases for gas chromatography (GC). In this work, a novel ionic liquid (IL) bonded polysiloxane ([PSOMIM][NTf₂]) with anion of bis-trifluoromethanesulfonylimide (NTf₂⁻) was synthesized, and another one with chloride anion ([PSOMIM][Cl]) was also prepared for the purpose of comparison. The thermo-stability of the product was evaluated by thermogravimetric (TG) test and the result indicated that [PSOMIM][NTf₂] did not decompose slightly until 380 °C. Then the solvation behaviors of the ILs were characterized using solvation parameter model. Subsequently, [PSOMIM][NTf₂] and [PSOMIM][Cl] were used as stationary phases to prepare capillary columns for GC, respectively. The column efficiency of [PSOMIM][NTf₂] column was 4776 plates/m (k = 3.64 ± 0.08, naphthalene), and that of the other one was 3170 plates/m (k = 2.84 ± 0.11, naphthalene). The selectivity of the novel stationary phases for analytes, including Grob reagent, aromatic positional isomers was further evaluated. Furthermore, the chromatograms of n-alkanes and polycyclic aromatic hydrocarbons (PAHs) on [PSOMIM][NTf₂] column were compared with that on [PSOMIM][Cl] column. [PSOMIM][NTf₂] stationary phase also exerted good selectivity for fatty acid methyl esters (FAMEs), polychlorinated biphenyls (PCBs) and aromatic amines.     

Fast and reversible CO2 quartz crystal microbalance response of vinylimidazolium‐based poly(ionic liquid)s

A series of poly(ionic liquid)s (pILs) based on the 1‐vinyl‐3‐hexylimidazolium polymerizable cation and on the bis(trifluoromethylsulfonyl)imide, nonafluoro‐1‐butanesulfonate, dodecylbenzenesulfonate, heptadecafluorooctanesulfonate, and 4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,11‐heptadecafluoroundecanoate anions have been synthesized and characterized. Their sorption/desorption response towards CO₂ has been tested through quartz crystal microbalance investigations. The obtained results show that all of the pILs here reported are featured by peculiar CO₂ sorption properties as they display fast and linear response, reversibility without any memory effect, and reproducibility, suggesting that anion plays a key role in determining sensitivity. Copyright © 2011 John Wiley & Sons, Ltd.     

Determination of water pollutants by direct-immersion solid-phase microextraction using polymeric ionic liquid coatings

The determination of a group of eighteen pollutants in waters, including polycyclic aromatic hydrocarbons and substituted phenols, is conducted in direct-immersion solid-phase microextraction (SPME) using the polymeric ionic liquid (PIL) poly(1-vinyl-3-hexadecylimidazolium) bis[(trifluoromethyl)sulfonyl]imide as a novel coating material. The performance of the PIL fiber coating in the developed IL-SPME-gas chromatography (GC)–mass spectrometry (MS) method is characterized by average relative recoveries of 92.5% for deionized waters and 90.8% for well waters, average precision values (as relative standard deviations, RSD%) of 11% for deionized waters and 12% for well waters, using a spiked level of 5 ng mL⁻¹. The detection limits oscillate from 0.005 ng mL⁻¹ for fluoranthene to 4.4 ng mL⁻¹ for 4-chloro-3-methylphenol, when using an extraction time of 60 min with 20 mL of aqueous sample. The extraction capabilities of the PIL fiber have been compared with the commercial SPME coatings: polydimethylsyloxane (PDMS) 30 μm, PDMS 100 μm and polyacrylate (PA) 85 μm. The PIL fiber is superior to the PDMS 30 μm for all analytes studied. A qualitative study was also carried out to compare among the nature of the coating materials by normalizing the coating thickness. The PIL material was shown to be more efficient than the PDMS material for all analytes studied. The PIL coating was also adequate for nonpolar analytes whereas the PA material was more sensitive for polar compounds.     

Quaternary phosphonium-based ionic liquids: Thermal stability and heat capacity of the liquid phase

In spite of the great importance of calorimetric data on phosphonium-based ionic liquids (PBILs), the information available in the literature is quite limited. This work reports the study of the thermal stability and the determination of heat capacity of the following (PBILs): tributyl(methyl)phosphonium methyl sulfate, [(C₄)₃PC₁][MeSO₄], trihexyl-tetradecylphosphonium chloride, [(C₆)₃PC₁₄][Cl], trihexyl-tetradecyl-phosphonium dicyanamide, [(C₆)₃ PC₁₄][DCA], trihexyl-tetradecylphosphonium bis((trifluoromethyl)sulfonyl) imide, [(C₆)₃ PC₁₄][NTf₂], and trihexyl-tetradecylphosphonium tris(pentafluoroethyl)trifluorophosphate, [(C₆)₃ PC₁₄][FAP]. Measurements on the well-known IL 1-ethyl-3-methylimidazoliumbis((trifluoromethyl)sulfonyl)imide, [EMIM][NTf₂], were also performed for comparative purposes. The thermal stability was assessed by conventional and high resolution modulated thermogravimetric analysis within the interval (303 to 873) K. The heat capacity was measured by modulated differential scanning calorimetry within the range (310 to 515) K with an uncertainty in the range (1 to 5) J · K^?1 · mol^?1. The experimental results were correlated using polynomial expressions. The Joback method for predicting ideal gas heat capacities was used in conjunction with the principle of corresponding states and the modified Lydersen–Joback–Reid method to predict the heat capacity of the ILs. The methods due to Valderrama et al. were also used with the same purpose.     

Ionic IPNs as novel candidates for highly conductive solid polymer electrolytes

Five ionic imidazolium based monomers, namely 1‐vinyl‐3‐ethylimidazolium bis(trifluoromethylsulfonyl)imide (ILM1), 1‐vinyl‐3‐(diethoxyphosphinyl)‐propylimidazolium bis(trifluoromethylsulfonyl)imide (ILM2), 1‐[2‐(2‐methyl‐acryloyloxy)‐propyl]‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (ILM3), 1‐[2‐(2‐methyl‐acryloyloxy)‐undecyl]‐3‐methylimidazolium bis(trifluoromethylsulfonyl)imide (ILM4), 1‐vinyl‐3‐ethylimidazolium dicyanamide (ILM5) were prepared and used for the synthesis of linear polymeric ionic liquids (PILs), crosslinked networks with polyethyleneglycol dimethacrylate (PEGDM) and interpenetrating polymer networks (IPNs) based on polybutadiene (PB). The ionic conductivities of IPNs prepared using an in situ strategy were found to depend on the ILM nature, T_g and the ratio of the other components. Novel ionic IPNs are characterized by increased flexibility, small swelling ability in ionic liquids (ILs) along with high conductivity and preservation of mechanical stability even in a swollen state. The maximum conductivity for a pure IPN was equal to 3.6 × 10^?5 S/cm at 20 °C while for IPN swollen in [1‐Me‐3‐Etim] (CN)₂N σ reached 8.5 × 10^?3 S/cm at 20 °C or 1.4 × 10^?2 S/cm at 50 °C. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4245–4266, 2009     

Synthesis and Thermophysical Properties of Ether‐Functionalized Sulfonium Ionic Liquids as Potential Electrolytes for Electrochemical Applications

During this work, a novel series of hydrophobic room temperature ionic liquids (ILs) based on five ether functionalized sulfonium cations bearing the bis{(trifluoromethyl)sulfonyl}imide, [NTf₂]^? anion were synthesized and characterized. Their physicochemical properties, such as density, viscosity and ionic conductivity, electrochemical window, along with thermal properties including phase transition behavior and decomposition temperature, have been measured. All of these ILs showed large liquid range temperature, low viscosity, and good conductivity. Additionally, by combining DFT calculations along with electrochemical characterization it appears that these novel ILs show good electrochemical stability windows, suitable for the potential application as electrolyte materials in electrochemical energy storage devices.     

Novel Bipyridinium Ionic Liquids as Liquid Electrochromic Devices

Novel mono and dialkylbipyridinium (viologens) cations combined with iodide, bromide, or bis(trifluoromethanesulfonyl)imide [NTf₂] as anions were developed. Selective alkylation synthetic methodologies were optimized in order to obtain the desired salts in moderate to high yields and higher purities. All prepared mono‐ and dialkylbipyridinium salts were completely characterized by ¹H, ¹³C, and ¹⁹F NMR spectroscopy, Fourier‐transform IR spectroscopy, and elemental analysis (in the case of NTf₂ salts). Melting points, glass transition temperatures by differential scanning calorimetry (DSC) studies, and decomposition temperatures were also checked for different prepared organic salts. Viscosities at specific temperatures and activation energies were determined by rheological studies (including viscosity dependence with temperature in heating and cooling processes). Electrochemical studies based on cyclic voltammetry (CV), differential pulsed voltammetry (DPV), and square‐wave voltammetry (SWV) were performed in order to determine the redox potential as well as evaluate reversibility behavior of the novel bipyridinium salts. As proof of concept, we developed a reversible liquid electrochromic device in the form of a U‐tube system, the most promising dialkylbipyridinium‐NTf₂ ionic liquid being used as the electrochromic material and the room‐temperature ionic liquid (RTIL), 1‐ethyl‐3‐methylimidazolium bis(trifluoromethanesulfonyl)‐imide [EMIM][NTf₂], as a stable and efficient electrolyte.     

Ionic Liquids as Internal Phase for Non‐Aqueous PolyHIPEs

Stable high internal phase emulsions (HIPEs) with the ionic liquid 1‐ethyl‐3‐methylimidazolium bis(trifluoromethyl‐sulfonyl)imide as dispersed phase were prepared and polymerised thermally into polyHIPEs. All polyHIPEs exhibited pore morphologies similar to that of polyHIPEs obtained with an aqueous dispersed phase. PolyHIPEs containing the dispersed phase possess a low T_g and are thermally stable in excess of 200 °C, offering the potential for new porous materials where water as dispersed phase is chemically or physically undesirable.     

The Kinetics of Ferrocene Volatilisation from an Ionic Liquid

The volatilisation of ferrocene (Fc), dissolved in the ionic liquid N‐butyl‐N‐methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, [C₄mpyrr][NTf₂], to the gas phase has been indirectly monitored by cyclic voltammetry and chronoamperometry. Simulation of the observed trends in concentration with time using a simple model allowed quantification of the process. Volatilisation of dissolved Fc under flowing wet and dry dinitrogen gas (N₂) was found to be kinetically limited with a rate constant in the region of 2×10^?7 cm s^?1. The activation energy of diffusion for Fc was found to be 28.2±0.7 kJ mol^?1, while the activation energy of volatilisation of Fc from [C₄mpyrr][NTf₂] to dry N₂ was found to be 85±2 kJ mol^?1.     

Electrochemical Determination of Manganese Solubility in Mercury via Amalgamation and Stripping in the Room Temperature Ionic Liquid n‐Hexyltriethylammonium Bis(trifluoromethanesulfonyl)imide, [N6,2,2,2][NTf2]

The solubility of manganese in mercury was determined electrochemically via amalgamation and stripping in the room temperature ionic liquid n‐hexyltriethylammonium bis(trifluoromethanesulfonyl)imide, [N_6,2,2,2][NTf₂]. A hemispherical mercury electrode was made by electrodepositing mercury onto a planar platinum microelectrode. Cyclic voltammetry of Mn²⁺ in [N_6,2,2,2][NTf₂] at the mercury microhemisphere electrode was investigated at temperatures of 298, 303 and 313 K. The solubility of Mn in Hg was determined on the basis of the charge under the reduction peak (Mn²⁺→Mn⁰) and the corresponding reoxidation.