自适应光学系统的数值模拟：动态控制过程和频率响应特性

对自适应光学系统的动态控制过程进行了数值模拟。与自动控制理论的解析分析相比,动态控制过程的数值模拟有其优越性。系统的频率响应特性与动态控制性能密切相关,对自适应光学系统的频率响应特性也进行了数值模拟。模拟计算的结果与实验测量结果符合得很好。还实现了多频率成份的同时计算,可以大大提高计算效率。其结果与单频率结果只在低频下有小的差别,可以满足得到带宽和裕量等参数的实用要求。将频率响应特性的模拟计算与长时间曝光斯特列耳（Strehl)比的数值模拟结合,可得到对自适应光学系统性能的有效评估。     

MONTE CARLO STUDIES OF RADIATION DAMAGE INDUCED BY FUSION DYNAMIC SIMULATION OF SPUTTERING

In this paper, the sputtering caused by fusion of ⁴He particles in the first wall materials is investigated by using the dynamic Monte Carlo simulation, which is based on the binary collision approximation. The dependences of sputtering yields on the incident energy and angle, as well as the comparisons of results calculated using the Monte Carlo methed with results from experiments, are discussed. Energy spectrum and angular distributions of sputtered species, the depth of origin of the sputtered particles as well as range distributions of incident ions are given. From a comparison between the related experimental data and the calculated results with static and dynamic simulation it has been found that a better agreement is obtained for dynamic simulation.     

MONTE CARLO STUDIES OF RADIATION DAMAGE INDUCED BY FUSION:DYNAMIC SIMULATION OF SPUTTERING

In this paper, the sputtering caused by fusion of ⁴He particles in the first wall materials is investigated by using the dynamic Monte Carlo simulation, which is based on the binary collision approximation. The dependences of sputtering yields on the incident energy and angle, as well as the comparisons of results calculated using the Monte Carlo methed with results from experiments, are discussed. Energy spectrum and angular distributions of sputtered species, the depth of origin of the sputtered particles as well as range distributions of incident ions are given. From a comparison between the related experimental data and the calculated results with static and dynamic simulation it has been found that a better agreement is obtained for dynamic simulation.     

托卡马克等离子体内部输运垒触发机制的数值模拟和并行效率

对托卡马克等离子体内部输运垒触发机制的动力学特征进行了数值模拟,通过区域分解法实现了数值模拟程序并行化,并行效率随计算机规模的增加而提高,结果与理论分析相吻合.并行模拟程序也适合MHD非线性撕裂模的数值求解.     

Stochastic modeling of coherent phenomena in strongly inhomogeneous media

A procedure of numerical simulation for coherent phenomena in multiply scattering media is developed on the basis of the juxtaposition of a Monte Carlo stochastic method with an iterative approach to the solution of the Bethe-Salpeter equation. The time correlation function and the interference component of coherent backscattering are calculated for scalar and electromagnetic fields. The results of simulation are in good agreement with experimental results, as well as with theoretical results obtained by generalizing the Milne solution.     

考虑量子化效应的MOSFET阈值电压解析模型

根据改进后的三角势阱场近似，并考虑量子化效应，提出了一种基于物理的阈值电压解析模型，给出了MOSFET的阈值电压解析表达式，并与经典理论和数值模拟结果进行了比较. 关键词： 量子效应 阈值电压 反型层 表面势     

白光LED光学仿真中的相关色温计算

光学仿真是白光LED照明设计中的一个重要方法,但色度分布的光学仿真中计算量太过庞大,以致在一般计算条件下无法得到可靠的仿真结果。为解决这一问题,本文利用色度转换关系和逐点法计算色温,引入数值拟合和像素合成两种处理方法,有效降低了光学仿真结果的涨落。通过对处理结果和实验结果在照度和相关色温两方面的对比,两种处理方法的有效性得到证明,大幅提升了基于色度配光的光学仿真计算效率。     

三层膜管壁结构的颈动脉超生仿真

颈动脉超声仿真 有助于血管壁超声检测及信号处理方法的性能评价。提出三层膜管壁结构的颈动脉超声仿真方法。根据组织散射点分布的形状和密度与超声回声斑点分布的变化规律,对临床图像统计分析,确定对应组织散射点分布、密度及强度等特征参数,利用FIELD II产生超声射频回波信号并得到B超图像。30 例仿真试验结果表明,血管壁内、中、外膜及血流回声的统计分布与临床B超图像的一致;与中心频率为8 MHz的结果相比,12 MHz仿真的内、中、外膜厚度及管腔直径测量均值与预设值相等,最大相对误差分别为4.01%, 1.25%, 0.04%及0.15%,仿真效果更为逼真。      

An ultrasound simulation method for carotid arteries with a wall structure of three membranes

Ultrasound simulation for carotid arteries is helpful to the performance assessments of vessel wall detection and signal processing methods by using ultrasound techniques.An ultrasound simulation method of carotid artery wall with a three-membrane structure is proposed in present study.According to the ultrasound speckle distributions varying with the shapes and densities of scatterer distributions,as well as the statistic results of the clinical images,the parameters of distributions,densities and intensities of scatterers for different kinds of tissues in the carotid artery phantoms are determined.Each region is acoustically characterized using FIELD II software to produce the radio frequency echo signals,from which ultrasound images are derived.The results based on 30 simulations show that the echo distributions of the intimae,mediae,adventitias and blood are consistent with the clinical ones.Moreover,compared with the results from the central frequency of 8 MHz,the mean measurements for thicknesses of the intima,media and adventitia membranes,as well as the lumen diameter from the simulation images based on 12 MHz are the same as the preset ones,and the maximum relative errors are the 4.01%,1.25%,0.04%and 0.15%,respectively.The simulation under this condition is more realistic.     

S波段相对论速调管放大器同轴输出腔的数值模拟

 介绍了S波段强流相对论速调管放大器（RKA）同轴输出腔内束波转换效率和腔主要参数的计算、微波提取的粒子模拟和优化以及实验。模拟计算时，采用单间隙的同轴输出腔，束压580 kV、束流4 kA的环行电子束，基波调制深度为80%，利用3维粒子程序得到约500 MW的微波输出功率，效率21.5%。将该模拟结果应用于实验的设计，实验中采用束压550 kV、束流4 kA的电子束得到功率500 MW、脉宽120 ns的输出微波，束波转换效率22.7%，实验结果与模拟结果吻合较好。     

Coupler design for an L-band electron linac

The RF coupler is a key component for an accelerating structure which is the most important component for a linac. In order to feed microwave power into the accelerating cavities effectively, the coupler has to be well matched with the feeding waveguide. In this paper, an electron linac coupler was designed, constructed and tested. A numerical simulation method based on the Kyhl's method was employed to search for the optimal dimensions of the coupler. The frequency and the coupling coefficient as a function of the coupler dimensions were also calculated. The results fitted the Kyhl's method simulation results well and gave tolerances of the coupler. The coupler was brazed to the accelerating cavities and it was cold-tested and hot-tested. The experimental results were consistent with the numerical simulation results.     

空间傅里叶分析法识别MHD扰动模式

讨论了用空间傅里叶分析法确定托卡马克等离子体MHD磁扰动模式的方法。根据托卡马克实验的状况,对不同情况下的MHD磁扰动进行了详细的数值模拟,重点分析了该方法的系统误差,模拟结果与HL-1M装置上的实验结果进行了对比。比较结果表明,用空间傅里叶分析法识别托卡马克中的MHD扰动模式是一种可以行之有效的方法。     

Modeling of pulsed spark discharge in water and its application to well cleaning

This paper presents a simulation model for the generation of strong pressure wave by means of pulsed spark discharge in water and its application to well cleaning. In the simulation model, one-dimensional time-dependent magnetohydrodynamic equations are coupled to a capacitive discharge circuit equation. A cylindrical conducting spark channel formed by electrical breakdown of water gap between a pair of electrodes is treated as a load of which resistance and inductance are allowed to change with time. For describing the spark channel properties accurately, precise calculations on thermodynamic properties and electrical conductivity are included in the simulation model. The simulation results show an excellent agreement with the experimentally measured shock pressure as well as the current and voltage waveforms. The simulation reveals that Joule heating of the spark channel during the very early phase of electrical discharge plays a key role in the formation of shock wave in water. The voltage on a capacitor at breakdown, the circuit inductance, and the resistance of the spark channel are found to be the most important parameters for the shock wave formation. With this technique, a pilot test for the cleaning of a clogged well has been performed in a water well which was constructed as a test-bed for riverbank filtration near the Anseong-cheon (river) in Korea. Well treatments have been carried out with an electrical energy of 510 J stored on a pulsed power system, at which the maximum shock pressure is measured to be around 7 MPa at the position of the well screen, i.e. 0.1 m away from the spark gap. A slug test shows 2.9 times improvement in the hydraulic conductivity of the well, which, combined with a visual inspection inside the well using an underwater camera, clearly demonstrates that the strong pressure wave generated by underwater spark discharge can effectively remove almost all incrustations formed in the well screen and thus improve well performance. Operating parameters for controlling the strength of shock pressure are discussed using the simulation model for extensive applications of the present technique to various types of water wells.     

Combined wave and ray based room acoustic simulations of audio systems in car passenger compartments,Part II: Comparison of simulations and measurements

The present series of papers summarizes the results of a three-year research project on the realistic simulation of sound fields in car passenger compartments using a combined Finite Element (FE) and Geometrical Acoustics (GA) approach. The simulations are conducted for the whole audible frequency range with the loudspeakers of the car audio system as the sound sources. The challenges faced during the project relate to fundamental questions regarding the realistic sound field simulation in small enclosures with strong modal and diffraction effects. While Part I of this series of papers focusses on the determination of the boundary and source conditions for the simulation model of the car compartment, the present paper, denoted here as Part II, presents extensive objective and subjective comparisons of the corresponding room acoustic measurement and simulation results.By applying the FE method to the low frequency part of the room transfer function (RTF) the study aims at the quantification of potential objective and subjective benefits with regard to the simulation quality in small rooms, when compared to a purely geometrical acoustics approach. The main challenges and limitations in the simulation domain are due to the very small volume, the difficult to determine source and boundary conditions and the considerable diffraction effects (especially at the seats) in the car passenger compartments. In order to keep the complexity of the FE simulations at a manageable level, all boundary conditions were described by acoustic surface impedances and no fluid-structural coupling was considered in the FE simulation model.While the results of the study reveal that an overall good agreement regarding the energy distribution in time and frequency domain is generally possible even in such complex enclosures, the results also clearly show the limitations of the impedance boundary approach in the FE domain as well as the strong sensitivity of the simulation results with regard to the uncertainty in the boundary and source conditions in both simulation domains. It can thus be concluded, that possible fields of application of the FE extension in room acoustic simulations lie in the prediction of the modally dominated low frequency part of the RTF of well defined rooms and in the prediction of sound fields that are strongly affected by near-field or diffraction effects as in the car passenger compartment. However, due to the considerable problems in the determination of realistic boundary conditions for the FE model, improved measurement techniques are urgently needed to further improve the overall simulation quality.     

粗糙度对大高宽比槽道内流动影响的数值模拟

基于确定表面粗糙结构形状的PML模型模拟表面粗糙度对大高宽比小槽道内流动特性的影响,并与3-D模拟结果对比,结果较为一致.基于该模型对不同的流速和不同的粗糙度进行模拟,结果表明:表面粗糙度导致槽道内出现速度线性分布的流动底层.Re数相同时,单位长度压降与相对粗糙度成二次方关系.粗糙单元高度相同时,压降随Re线性增加.     

叠阵巴条指向性对空心导管耦合系统的影响

在空心导管泵浦耦合系统中,测量了激光二极管叠阵中巴条的实际指向性,并带入仿真建模中,以便获得更准确、更优的模拟结果。与采用理想巴条指向性的模型模拟结果相比,耦合系统的耦合效率降低了11.2%。同时,带入实际指向性的模型模拟结果,具有更大的能量传输损耗和调制更深的泵浦光场分布,且该仿真模拟结果与实验结果相符。结果表明,在空心导管耦合系统设计中,带入实际巴条指向性模型是获得精确模拟结果的必要条件。     

Gain and threshold properties of InGaAsN/GaAsN material system for 1.3-μm semiconductor lasers

The gain properties and valence subbands of InGaAsN/GaAsN quantum-well structures are numerically investigated with a self-consistent LASTIP simulation program. The simulation results show that the InGaAsN/GaAsN has lower transparency carrier density than the conventional InGaAsP/InP material system for 1.3-μm semiconductor lasers. The material gain and radiative current density of InGaAsN/GaAsN with different compressive strains in quantum well and tensile strains in barrier are also studied. The material gain and radiative current density as functions of strain in quantum well and barrier are determined. The simulation results suggest that the laser performance and Auger recombination rate of the 1.3-μm InGaAsN semiconductor laser may be markedly improved when the traditional GaAs barriers are replaced with the AlGaAs graded barriers.     

�����Է��ﲣ���̻�ר�õ�����������ֵģ����ʵ���о�

采用了数值模拟与实验结合的方法研究了用于模拟放射性固体废物玻璃固化的非转移弧型等离子体炬的电、热特性。基于包括电弧室和开放空间在内的3D 模型得到了电弧等离子体和等离子体射流的温度场。根据计算结果,电弧室内的最高温度位于第一阳极内,达到41.77×10 K;弧电压的计算值高于实测值,二者之间的差异随着电流强度的增大而逐渐减小。采用该等离子体炬熔融模拟废物的实验发现,所确定的等离子体炬到炉底的距离能够满足废物熔融的要求,与计算的结果相符合。上述结果表明,数值模拟的结果可以作为等离子体炉工程设计的依据,并可以用作进一步分析等离子体炉炉膛内工艺过程的输入条件。     

确定峰度非高斯海洋环境噪声模型研究

针对非高斯海洋环境噪声仿真问题,利用对衰减正弦信号均匀采样方法,产生了具有特定谱特性同时具有特定峰度值的非高斯海洋环境噪声序列。在理论仿真条件下,通过对低峰度值和高峰度值的分别讨论发现,当峰度值高于3.0时总可以仿真得到较好的结果,而当峰度值低于3.0时,需通过降采样或降阶的方法解决不能仿真的问题。4种海上试验条件下的仿真结果表明,在安静环境、单一航船干扰环境、气枪声源干扰环境以及冲击性干扰环境下,都可以产生与目标谱特性、统计特性几乎相同的非高斯海洋环境噪声序列。      

EAST装置微波反射成像系统光学性能评测

用宽为1cm的金属反射平面对EAST装置上96道(极向12道×径向8道)微波成像反射计的前端接收光路的道间距和探测光斑半径进行了测试,结果与仿真结果较为一致。用极向旋转的金属轮面作为反射面,研究了非理想光学条件下反射面旋转所引入的多普勒频移,结果与模拟值吻合。