Electropolymerized composite film of polypyrrole and functionalized multi-walled carbon nanotubes: effect of functionalization time on capacitive performance

The composite film of polypyrrole and functionalized multi-walled carbon nanotubes (PPy/F-MWNTs) was prepared by electropolymerization. MWNTs were functionalized by sonicating with a concentrated solution of H₂SO₄/HNO₃ (3/1, volume ratio) in a water bath for different times. The carbon nanotubes (CNTs) are cut into smaller portions with more functional groups introduced on their surface when the sonicating time (nominated as functionalization time hereafter) is increased. However, the specific capacitance of the composite film reaches a maximum of 240 F g⁻¹ at the scanning rate of 10 mV s⁻¹ when MWNTs are functionalized for 24 h, which is about 205 F g⁻¹, 225 F g⁻¹ and 232 F g⁻¹, respectively, when MWNTs are functionalized for 6 h, 12 h and 48 h. At a current load of 1.0 A g⁻¹, PPy/F-MWNT composite film functionalized for 24 h (PPy/F-MWNTs (24 h)) retains 93.49% of its initial capacitance after 1,000 cycles of galvanostatic charge/discharge, and the discharge efficiency is higher than 98.15% during cycling. High specific capacitance, good rate performance, fast charge/discharge ability and long cycling life are ascribed to the synergistic effect of the two components to form a porous composite film as well as the easy accessibility of counter ions into the film. Therefore, PPy/F-MWNT (24 h) composite film is a kind of promising electrode material for supercapacitors. The mechanism of underfunctionalization and overfunctionalization of carbon nanotubes is also discussed.     

The preparation and performance of flocculent polyaniline/carbon nanotubes composite electrode material for supercapacitors

Polyaniline (PANI)/carbon nanotubes (CNTs) composite electrode material was prepared by in situ chemical polymerization. The structure and morphology of PANI/CNTs composite are characterized by Fourier infrared spectroscopy, scanning electron microscope, and transmission electron microscopy. It has been found that a flocculent PANI was uniformly deposited on the surface of CNTs. The supercapacitive behaviors of the PANI/CNTs composite materials are investigated with cyclic voltammetry, galvanostatic charge/discharge, impedance, and cycle life measurements. The results show that the PANI/CNTs composite electrodes have higher specific capacitances than CNT electrodes and better stability than the conducting polymers. The capacitance of PANI/CNTs composite electrode is as high as 837.6 F g⁻¹ measured by cyclic voltammetry at 1 mV s⁻¹. Besides, the capacitance retention of coin supercapacitors remained 68.0% after 3,000 cycles.     

Preparation and characterization of AuPt alloy nanoparticle–multi-walled carbon nanotube–ionic liquid composite film for electrocatalytic oxidation of cysteine

Gold–platinum (AuPt) alloy particles were fabricated directly on multi-walled carbon nanotubes (MWNT)–ionic liquid (i.e., trihexyltetradecylphosphonium bis(trifluoromethylsulfonyl)imide, [P_6,6,6,14][NTf₂]) composite coated glassy carbon electrode (GCE) by electrodeposition method. Scanning electron microscope image showed that they were well-dispersed nanocluster consisting of smaller nanoparticles, and their size was about 70 nm. X-ray diffraction experiment showed that they were single-phase alloy nanomaterial, and the calculated composition was consisting with that obtained by energy dispersive X-ray spectroscopy. The resulting modified electrode (i.e., AuPt–MWNT–[P_6,6,6,14][NTf₂]/GCE) presented high catalytic activity for the electrochemical oxidation of cysteine. The peak potential of cysteine shifted to 0.42 V (versus saturated calomel electrode) in 0.1 M H₂SO₄ and the peak current increased greatly in comparison with that on the corresponding Pt (or Au)–MWNT–[P_6,6,6,14][NTf₂]/GCE. Under the optimized conditions, the oxidation current of cysteine at 0.45 V was linear to its concentration in the range of 5.0 × 10⁻⁷ ∼ 4.0 × 10⁻⁵ M with a sensitivity of 43.8 mA M⁻¹.     

Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

Electrochemical deposition of platinum nanoparticles in multiwalled carbon nanotube–Nafion composite for methanol electrooxidation

Platinum nanoparticles were successfully deposited within a multiwalled carbon nanotube (MWCNT)–Nafion matrix by a cyclic voltammetry method. A Pt(IV) complex was reduced to platinum nanoparticles on the surface of MWCNTs. The resulting Pt nanoparticles were characterized by scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The Pt–MWCNT–Nafion nanocomposite film-modified glassy carbon electrode had a sharp hydrogen desorption peak at about −0.2 V vs. Ag/AgCl (3 M) in a solution of 0.5 M H₂SO₄, which is directly related to the electrochemical activity of the Pt nanoparticles presented on the surface of MWCNTs. The electrocatalytic properties of the Pt–MWCNT–Nafion nanocomposite-modified glassy carbon electrode for methanol electrooxidation were investigated by cyclic voltammetry in a 2 M CH₃OH + 1 M H₂SO₄ solution. In comparison with the Pt-coated glassy carbon electrode and the Pt–Nafion modified glassy carbon electrode, the Pt–MWCNT–Nafion-modified electrode had excellent electrocatalytic activity toward methanol electrooxidation. The stability of the Pt–MWCNT–Nafion nanocomposite-modified electrode had also been evaluated.     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Effect of nanoscale CeO<Subscript>2</Subscript> on PVDF-HFP-based nanocomposite porous polymer electrolytes for Li-ion batteries

New poly (vinylidenefluoride-co-hexafluoro propylene) (PVDF-HFP)/CeO₂-based microcomposite porous polymer membranes (MCPPM) and nanocomposite porous polymer membranes (NCPPM) were prepared by phase inversion technique using N-methyl 2-pyrrolidone (NMP) as a solvent and deionized water as a nonsolvent. Phase inversion occurred on the MCPPM/NCPPM when it is treated by deionized water (nonsolvent). Microcomposite porous polymer electrolytes (MCPPE) and nanocomposite porous polymer electrolytes (NCPPE) were obtained from their composite porous polymer membranes when immersed in 1.0 M LiClO₄ in a mixture of ethylene carbonate/dimethyl carbonate (EC/DMC) (v/v = 1:1) electrolyte solution. The structure and porous morphology of both composite porous polymer membranes was examined by scanning electron microscope (SEM) analysis. Thermal behavior of both MCPPM/NCPPM was investigated from DSC analysis. Optimized filler (8 wt% CeO₂) added to the NCPPM increases the porosity (72%) than MCPPM (59%). The results showed that the NCPPE has high electrolyte solution uptake (150%) and maximum ionic conductivity value of 2.47 × 10⁻³ S cm⁻¹ at room temperature. The NCPPE (8 wt% CeO₂) between the lithium metal electrodes were found to have low interfacial resistance (760 Ω cm²) and wide electrochemical stability up to 4.7 V (vs Li/Li⁺) investigated by impedance spectra and linear sweep voltammetry (LSV), respectively. A prototype battery, which consists of NCPPE between the graphite anode and LiCoO₂ cathode, proves good cycling performance at a discharge rate of C/2 for Li-ion polymer batteries.     

Voltammetric sensor for nitrite determination based on its electrocatalytic reduction at the surface of p-duroquinone modified carbon paste electrode

A p-duroquinone (tetramethyl-p-benzoquinone) modified carbon paste electrode (DMCPE) was employed to study the electrocatalytic reduction of nitrite in aqueous solutions using cyclic voltammetry (CV), double potential-step chronoamperometry, and differential pulse voltammetry (DPV). It has found that under an optimum condition (pH 1.00), the reduction of nitrite at the surface of DMCPE occurs at a potential of about 660 mV less negative than that of an unmodified carbon paste electrode (CPE). The catalytic rate constant, k′_h, based on Andrieux and Saveant theoretical model was calculated as for scan rate 10 mV s^-1. Also, the apparent diffusion coefficient, D _app, was found as 2.5 × 10^–10 and 3.61 × 10^–5 cm² s^-1 for p-duroquinone in carbon paste matrix and nitrite in aqueous buffered solution, respectively. The values for αn_α were estimated to be −0.65 and −0.19 for the reduction of nitrite at the surface of DMCPE and CPE, respectively. The electrocatalytic reduction peak currents showed a linear dependence on the nitrite concentration, and a linear analytical curve was obtained in the ranges of 5.0 × 10^–5 M to 8.0 × 10^–3 M and 6.0 × 10^–6 M to 8.0 × 10^–4 M of nitrite concentration with CV and DPV methods, respectively. The detection limits (2σ) were determined as 2.5 × 10^–5 M and 4.3 × 10^–6 M by CV and DPV methods. This method was also applied as a simple, selective and precise method for determination of nitrite in real samples (the weak liquor from the wood and paper factory of Mazandaran province in Iran) by using a standard addition method.     

Electrochemical performance of Co–Al layered double hydroxide nanosheets mixed with multiwall carbon nanotubes

Regular hexagonal Co–Al layered double hydroxides (Co–Al LDH) were synthesized by urea-induced homogeneous precipitation. This material proved to be nanosheets by scanning electron microscopy and X-ray diffraction measurements. The electrochemical capacitive behavior of the nanosheets in 1 M KOH solution were evaluated by constant current charge/discharge and cyclic voltammetric measurements, showing a large specific capacitance of 192 F·g⁻¹ even at the high current density of 2 A·g⁻¹. When multiwall carbon nanotubes (MWNTs) were mixed with the Co–Al LDH, it was found that the specific capacitance and long-life performance of all composite electrodes at high current density are superior to pure LDH electrode. When the added MWNTs content is 10 wt%, the specific capacitance increases to 342.4 F·g⁻¹ and remains at a value of 304 F·g⁻¹ until the 400th cycle at 2 A·g⁻¹, showing that this is a promising electrode material for supercapacitors working at heavy load. According to the electrochemical impedance spectra, MWNTs greatly increase the electronic conductivity between MWNTs and the surface of Co–Al LDH, which consequently facilitates the access of ions in the electrolyte and electrons to the electrode/electrolyte interface.     

Electrochemical capacitance of nickel oxide nanotubes synthesized in anodic aluminum oxide templates

Nickel oxide (NiO) nanotubes for supercapacitors were synthesized by chemically depositing nickel hydroxide in anodic aluminum oxide templates and thermally annealing at 360 °C. The synthesized nanotubes have been characterized by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction. The capacitive behavior of the NiO nanotubes was investigated by cyclic voltammetry, galvanostatic charge–discharge experiment, and electrochemical impedance spectroscopy in 6 M KOH. The electrochemical data demonstrate that the NiO nanotubes display good capacitive behavior with a specific capacitance of 266 F g⁻¹ at a current density of 0.1 A g⁻¹ and excellent specific capacitance retention of ca. 93% after 1,000 continuous charge–discharge cycles, indicating that the NiO nanotubes can become promising electroactive materials for supercapacitor.     

Electrical and electrochemical studies on magnesium ion-based polymer gel electrolytes

The development of polymer gel electrolyte system with high ionic conductivity is the main objective of polymer research. Electrochemical devices based on lithium ion-conducting polymer electrolyte are not safe due to the explosive nature of lithium. An attempt has been made to synthesize magnesium ion-conducting polymeric gel electrolytes, poly (vinylidene fluoride-co-hexafluoropropylene)–propylene carbonate–magnesium perchlorate, PVdF(HFP)-PC–Mg(ClO₄)₂ using standard solution-cast techniques. The maximum room temperature ionic conductivity of the synthesized electrolyte system has been observed to be 5.0 × 10⁻³ S cm⁻¹, which is quite acceptable from a device fabrication point of view. The temperature-dependent conductivity and the dielectric behavior were also analyzed. The pattern of the temperature-dependent conductivity shows the Arrhenius behavior. The dielectric constant ε _r and dielectric loss ε _i increases with temperature in the low-frequency region but almost negligible in the high-frequency region. This behavior can be explained on the basis of electrode polarization effects. The real part M _r and imaginary part M _i versus frequency indicate that the systems are predominantly ionic conductors. Further, the synthesized electrolyte materials have been checked for its suitability in energy storage devices namely redox supercapacitor with conducting polymer polypyrrole as electrode materials, and finally, it was observed that it shows good capacitive behavior in low-frequency region. Preliminary studies show that the overall capacitance of 22 mF cm⁻² which is equivalent to a single electrode specific capacitance of 117 F gm⁻¹ was observed for the above said supercapacitors.     

A solid-contact Pb2+-selective polymeric membrane electrode with Nafion-doped poly(pyrrole) as ion-to-electron transducer

Conducting polymer poly(pyrrole) (PPy) doped with Nafion was successfully used as ion-to-electron transducer in the construction of a solid-contact Pb²⁺-selective polymeric membrane electrode. The Nafion dopant can effectively increase the capacitance of the conducting polymer and improve the mechanical robustness of the coating. The transducer layer, PPy-Nafion, characterized by cyclic voltammetry and electrochemical impedance spectroscopy, exhibits a sufficiently high bulk (redox) capacitance and fast ion and electron transport process. The new Pb²⁺-selective polymeric membrane electrode, based on PPy-Nafion film as solid contact, shows stable Nernstian characteristics in Pb(NO₃)₂ solution within the concentration range of 1.0 × 10⁻⁷–1.0 × 10⁻³ M, and the detection limit is 4.3 × 10⁻⁸ M. The potential stability of the electrode and the influence of the interfacial water layer were also evaluated by chronopotentiometry and potentiometric water layer test, respectively. The results show that the solid-contact Pb²⁺-selective electrode, based on PPy-Nafion film as ion-to-electron transducer, can effectively overcome the potential drift and reduce the water layer between the PPy-Nafion transducer layer and the ion-selective membrane.     

Fabrication and properties of MgF<Subscript>2</Subscript> composite film modified with carbon nanotubes

Carbon nanotubes (CNTs) were used to modify magnesium fluoride (MgF₂) film via the spin coating technique. Nanoparticles of MgF₂ were in situ synthesized on surfaces of CNTs resulted in the composites (MgF₂–CNTs) by means of sol–gel technique. The sizes of the MgF₂ nanoparticles in situ synthesized on CNTs surfaces could be modulated by processing the MgF₂ sol–gel in different ways. The MgF₂–CNTs as prepared was mixed with MgF₂ sol to fabricate composite films (MgF₂–CNTs/MgF₂). Instead of adding directly CNTs, adding MgF₂–CNTs, into MgF₂ sol could effectively improve the dispersion of CNTs, avoid emergence of carbon clusters in the compsite film, decrease surface roughness of the film, and enhance the interaction between the CNTs and MgF₂ matrix. In the paper, the MgF₂ nanoparticles were in situ synthesized on the surfaces of multi-walled carbon nanotubes (MWCNTs) and single-walled carbon nanotubes (SWCNTs) respectively to prepare MgF₂–SWCNTs/MgF₂ and MgF₂–MWCNTs/MgF₂ composite films. Experimental results showed that the transparency of the MgF₂–SWCNTs/MgF₂ composite film was higher than that of the MgF₂–MWCNTs/MgF₂ film in the range of ultraviolet, visible and near-infrared wavelengths. The results showed SWCNTS could be an ideal reinforcement of MgF₂ films to get good toughness, and retain its optical transmittance at the same time.     

Application of chitosan/iota-carrageenan polymer electrolytes in electrical double layer capacitor (EDLC)

In this work, a chitosan/iota (ι)-carrageenan blended film doped with orthophosphoric acid (H₃PO₄) as ionic dopant and poly(ethylene glycol) (PEG) as plasticizer has been used as a separator and electrolyte in an electrical double layer capacitor (EDLC). A set of samples were prepared by the solution cast technique to see the effect of the different weight ratios of the proton donor and plasticizer on the conductivity. The highest conducting sample has composition 37.50 wt.% chitosan–37.50 wt.% ι-carrageenan–18.75 wt.% H₃PO₄–6.25 wt.% PEG. The conductivity value is 6.29 × 10⁻⁴ S cm⁻¹. The conductivity–temperature relationship is Arrhenian, and the activation energy for the highest conducting sample is 0.09 eV. The specific discharge capacitance of the EDLC is 35 F g⁻¹ at 0.11 mA cm⁻² current drain and was constant for 30 cycles.     

Improvement of high-voltage cycling behavior of Li(Ni1/3Co1/3Mn1/3)O2 cathodes by Mg, Cr, and Al substitution

To improve the electrochemical properties of Li[Ni_1/3Co_1/3Mn_1/3]O₂ at high charge end voltage (4.6 V), a series of the mixed transition metal compounds, Li(Ni_1/3Co_{1/3 − x} Mn_1/3M _x )O₂ (M = Mg, Cr, Al; x = 0.05), were synthesized via hydroxide coprecipitation method. The effects of doping Mg, Cr, and Al on the structure and the electrochemical performances of Li[Ni_1/3Co_1/3Mn_1/3]O₂ were compared by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), galvanostatic charge–discharge tests, and electrochemical impedance spectroscopy. The XRD results show that all the samples keep layered structures with R3m space group as the Li[Ni_1/3Co_1/3Mn_1/3]O₂. SEM images show that all the compounds have spherical shapes and the Cr-doped sample has the largest particle size. Furthermore, galvanostatic charge–discharge tests confirm that the Cr-doped electrode shows improved cycling performance than the undoped material. The capacity retention of Li(Ni_1/3Co_{1/3 − 0.05}Mn_1/3Cr_0.05)O₂ is 97% during 50 cycles at 2.8∼4.6 V. The improved cycling performance at high voltage can be attributed to the larger particle size and the prevention of charge transfer resistance (R _ct) increase during cycling.     

Preparation and electrochemical performance of activated carbon thin films with polyethylene oxide-salt addition for electrochemical capacitor applications

The effect of polymer–salt addition in the activated carbon electrode for electric double-layer capacitor (EDLC) has been investigated. A series of composite thin film electrode consisting of activated carbon, carbon black, polytetrafluoroethylene and polymer–salt complex (polyethyleneoxide–LiClO₄) with an appropriate weight ratio were prepared and examined their performance for EDLCs using 1 mol L⁻¹ LiClO₄ in ethylene carbonate:diethylcarbonate electrolyte solution. The electrochemical capacitance performances of these electrodes with different compositions were characterized by cyclic voltammetry, galvanostatic charge–discharge cycling, and AC impedance measurements. By comparison, the best results were obtained with a composite electrode rich in polymer–salt additive (132 F g⁻¹ at 100 mA g⁻¹ of galvanostatic experiment). In general, the polymer–salt-containing electrode had shown improved performance over activated carbon electrodes without polymer–salt at high current density.     

Fabrication of TiO2/Ti nanotube electrode and the photoelectrochemical behaviors in NaCl solutions

Titanium oxide nanotube electrodes were successfully prepared by anodic oxidation on pure Ti sheets in 0.5 wt.% NH₄F + 1 wt.% (NH₄)₂SO₄ + 90 wt.% glycerol mixed solutions. Nanotubes with diameter 40–60 nm and length 7.4 μm were observed by field emission scanning electron microscope. The electrochemical and photoelectrochemical characteristics of TiO₂ nanotube electrode were investigated using linear polarization and electrochemical impedance spectroscopy techniques. The open-circuit potential dropped markedly under irradiation and with the increase of Cl⁻ concentrations. A saturated photocurrent of approximately 1.3 mA cm⁻² was observed under 10-W low-mercury lamp irradiation in 0.1 M NaCl solution, which was much higher than film electrode. Meanwhile, the highest photocurrent in NaCl solution implied that the photogenerated holes preferred to combine with Cl⁻. Thus, a significant synergetic effect on active chlorine production was observed in photoelectrocatalytic processes. Furthermore, the generation efficiency for active chlorine was about two times that using TiO₂/Ti film electrode by sol–gel method. Finally, the effects of initial pH and Cl⁻ concentration were also discussed.     

Electrochemical reduction of NO on La2-x Sr x NiO4 based electrodes

The series La_2 − x Sr _x NiO₄ (x = 0.0, 0.05, 0.15, 0.25, 0.35, and 1.0) was tested for functionality as electrode materials for direct electrochemical reduction of NO. The materials were tested using cyclic voltammetry in 1% NO and 10% O₂ in Ar on a cone-shaped electrode. The best materials for the electrochemical reduction of NO are La₂NiO₄ and LaSrNiO₄, which have current densities for NO reduction 1.82 and 7.09 times higher, respectively, than for O₂ at 400 °C. Increasing the temperature decreased the ability to reduce NO before O₂ while the activity increased. The adsorbed species during direct decomposition was attempted, clarified using X-ray absorption near-edge structure experiments and thermogravimetry, but no conclusive results were obtained.     

Electrochemical synthesis of Fe3O4-PB nanoparticles with core-shell structure and its electrocatalytic reduction toward H2O2

The Fe₃O₄-Prussian blue (PB) nanoparticles with core-shell structure have been in situ prepared directly on a nano-Fe₃O₄-modified glassy carbon electrode by cyclic voltammetry (CV). First, the magnetic nano-Fe₃O₄ particles were synthesized and characterized by X-ray diffraction. Then, the properties of the Fe₃O₄-PB nanoparticles were characterized by CV, electrochemical impedance spectroscopy, and superconducting quantum interference device. The resulting core-shell Fe₃O₄-PB-modified electrode displays a dramatic electrocatalytic ability toward H₂O₂ reduction, and the catalytic current was a linear function with the concentration of H₂O₂ in the range of 1 × 10⁻⁷~5 × 10⁻⁴ mol/l. A detection limit of 2 × 10⁻⁸ (s/n = 3) was determined. Moreover, it showed good reproducibility, enhanced long-term stability, and potential applications in fields of magnetite biosensors.     

Simultaneous voltammetric determination of ascorbic acid and dopamine at the surface of electrodes modified with self-assembled gold nanoparticle films

Gold nanoparticles (GNs) could be efficiently immobilized on binary mixed self-assembled monolayers (SAMs) on a gold surface composed of 1,6-hexanedithiol and 1-octanethiol (nano-Au/SAMs gold electrode). This GN chemically modified electrode was used for electrochemical determination of ascorbic acid (AA) and dopamine (DA) in aqueous media. The result showed that the GN-modified electrode could clearly resolve the oxidation peaks of AA and DA, with a peak-to-peak separation (∆E _p) of 110 mV enabling determination of AA and DA in the presence of each other. The linear analytical curves were obtained in the ranges of 0.3–1.4 mM for AA and 0.2–1.2 mM for DA concentrations using differential pulse voltammetry. The detection limits (3σ) were 9.0 × 10⁻⁵ M for AA and 9.0 × 10⁻⁵ M for DA.