焙烧温度对SiO2负载的Co3O4纳米粒子表面氧缺陷浓度和CO氧化催化性能的影响

以传统的浸渍法,在不同焙烧温度下制备了用于CO氧化反应的Co₃O₄/SiO₂催化剂．通过激光拉曼光谱(Raman)、X射线光电子能谱(XPS)、X射线衍射(XRD)、程序升温还原(TPR)和X射线吸收精细结构谱(XAFS)表征了该系列催化剂的结构．在所有的催化剂中,XRD和Raman光谱都只检测到了Co₃O₄晶相的存在．与Co₃O₄体相相比,XPS结果表明在200 oC焙烧的(Co₃O₄(200)/SiO₂)催化剂中Co₃O₄表面上存在着过量的Co²⁺．与XPS的结果一致,TPR结果表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄表面上存在氧缺陷, 并且XAFS结果也表明Co₃O₄(200)/SiO₂催化剂中Co₃O₄具有更多的Co²⁺．提高焙烧温度使得过量的Co²⁺进一步氧化为Co³⁺,同时降低了表面氧缺陷浓度,从而得到计量比的Co₃O₄4/SiO₂催化剂．在所有的负载催化剂中Co₃O₄(200)/SiO₂催化剂表现出了最好的CO氧化催化性能,表明过量Co²⁺和表面氧缺陷的存在能够促进Co₃O₄催化CO氧化反应的活性.     

一维Ni0.5Zn0.5Fe2O4/SiO2复合纳米结构的制备及其磁性能

采用溶胶-凝胶法结合静电纺丝技术制备了Ni_0.5Zn_0.5Fe₂O₄/SiO₂复合纳米纤维.利用热重-差热分析、X射线衍射、场发射扫描电镜、高分辨透射电镜和振动样品磁强计研究了前驱体纤维的热分解及相转化过程以及焙烧温度和SiO₂含量对目标纳米纤维的相组成、微观结构、形貌及磁性能的影响.结果表明,在450 ℃焙烧时,立方尖晶石结构已基本形成.随着焙烧温度由450 ℃升高到100     

Mg2+掺杂Zn2SiO4:Mn2+的溶胶-凝胶法合成及真空紫外发光特性研究

采用溶胶-凝胶法（sol-gel method）于不同气氛条件下成功合成了Zn_1.92-xMg_xSiO₄:0.08Mn²⁺（0≤x≤0.12）系列粉末样品.利用X射线衍射(XRD)、光致发光(PL)谱等分析手段对Zn_1.92-xMg_xSiO₄:0.08Mn²⁺系列     

非晶态SiO2的高温高压转变研究

利用金刚石对顶砧高压装置和激光双面加热技术, 以经700°C热处理后的吉林长白山硅藻土作为非晶态SiO₂样品,在0—4GPa, 1000—1300K温压条件下开展同步辐射X射线衍射原位测试(EDXD方法), 研究非晶态SiO₂在高温高压条件下的结晶转变方式. 测试结果表明, 在0.8—2.4GPa, 1000—1300K温压条件下, 非晶态SiO₂转变成α-石英而非β-石英或方石英, 其结晶温度较常压下非晶态SiO₂晶化所需温度明显较低, 表明压力有利于降低非晶态SiO₂转变的活化能, 并与常压下的结晶产物不同. 在3—4GPa, 1300K温压条件下, 非晶态SiO₂和石英均转变成了柯石英.     

SiO2半波覆盖层对HfO2/SiO2高反膜激光损伤的影响

 研究了SiO₂半波覆盖层对HfO₂/SiO₂高反射膜1064nm激光损伤的影响,分析薄膜的激光损伤特性及图貌得出, 对于单脉冲（1-ON-1）激光损伤,SiO₂半波覆盖层能提高HfO₂/SiO₂高反膜的激光损伤阈值;可显著降低激光损伤程度,减小灾难性损伤发生的概率;可大幅度提高HfO₂/SiO₂高反膜膜的抗激光损伤能力。     

层间热处理对SiO2/ZrO2双层膜的影响

 以正硅酸乙酯和丙醇锆为前驱体,用溶胶-凝胶法在K9基片上提拉镀制SiO₂/ZrO₂双层膜。采用不同实验步骤制备了2个样品,样品1镀完SiO₂后直接镀ZrO₂ ,样品2镀完SiO₂经热处理后再镀ZrO₂。采用原子力显微镜、椭偏仪、紫外-可见分光光度计对薄膜进行表征。针对SiO₂/ZrO₂双层膜,考虑到膜间渗透的影响,采用３层Cauchy模型进行椭偏模拟,椭偏参数的模拟值曲线与椭偏仪的测量值曲线十分吻合,进而发现热处理可以使SiO₂/ZrO₂双层膜之间的渗透减少近23 nm,从而提高其峰值透射率。利用输出波长1.064 mm,脉宽8.1 ns的激光束对样品进行了损伤阈值的测试,用光学显微镜观察损伤形貌,结果发现两者损伤阈值分别为13.6 J/c2和14.18 J/cm²,均为膜的本征损伤。     

不同后处理方法对溶胶-凝胶SiO2膜层抗污染能力的影响

 以正硅酸乙酯作为前驱体,利用碱催化方式制备了SiO₂溶胶,采用提拉法在K9基片上镀制SiO₂单层薄膜,分别用热处理、紫外辐射处理、氨水加六甲基二硅胺烷气氛处理和酸碱复合膜4种后处理法对膜层进行处理,采用分光光度计、红外光谱、扫描探针显微镜、静滴接触角测量仪、椭偏仪等分析了薄膜的特性,通过真空环境加速污染实验对处理前后的膜层进行抗污染能力对比,结果表明：在碱性SiO₂膜层上加镀一层酸性SiO₂膜的复合膜层整体透过率仍保持在99%以上,疏水角达到128°,膜层真空抗污染能力大大加强。     

三维海胆状Co3O4的微纳结构制备及锂电池性能

水热法制备的合成海胆状Co₃O₄前驱物在空气中退火得到三维海胆状Co₃O₄的微纳结构. 采用FESEM、TEM、HRTEM以及XRD对产物进行形貌和结构的表征. 结果表明,合成的海胆状结构Co₃O₄由许多粒径约为15 nm的颗粒串接形成. 锂电池测试性能表明,制备的海胆状Co₃O₄首次放电容量达到1.369 Ah/g,经过20次循环     

从可溶性单源分子前驱体采用溶胶凝胶法制备ZnO/TiO2 纳米复合物

合成了单源分子前驱体Cl₂TiZn(dmae)₄ (dmae为2-二甲基乙醇胺),并以乙醇为溶剂,加入等摩尔量的水对其进行可控水解得ZnO/TiO₂纳米复合凝胶,经pH=9沉淀,在200、400和600 oC 烧结得到不同的产物T₂₀₀、T₄₀₀、T₆₀₀. XRD分析表明未烧结产物为无定形粉末并随着烧结温度升高晶型改善. ZnO呈纤锌矿结构(六方晶系),TiO₂呈板钛矿型结构(正交). BET分析和扫描电镜表明颗粒的大小随着烧结温度的提高而增加. 红外光谱证明Zn-O和Ti-O的特有的振动频率,OH基团烧结后的产物中被去掉. 所有的样品都显示良好的光催化活性, 且T₆₀₀活性最高.     

氧分压对HfO2薄膜残余应力的影响及有限元分析

 利用电子束蒸发法制备了单层HfO₂膜,控制氧气流量从0 mL/min以步长5 mL/min递增至25 mL/min(标况下)。利用ZYGO干涉仪测量基片镀膜前后的面形变化,代入Stoney公式计算出残余应力,分析了不同氧压下残余应力的变化情况。随着氧压的增大,残余应力由张应力逐渐过渡到压应力,当氧压过大时,压应力减小。因此可以通过改变氧压来控制应力。应力的变化与薄膜的微观结构密切相关,分析了所有样品的X射线衍射图（XRD）,发现均为非晶结构。利用Ansys建立基片-薄膜有限元模型,将应力作用下基片的形变与实验结果进行对比,验证所建立的模型,为分析HfO₂/SiO₂膜堆应力的匹配设计提供参考。     

Laser-driven synthesis and magnetic properties of iron nanoparticles

Nanoparticles of iron have been prepared by laser-driven decomposition of iron pentacarbonyl vapor. In this method, an infrared laser rapidly heats a dilute mixture of precursor vapors to decompose the precursor and initiate particle nucleation. It was found that when using SF₆ as a photosensitizer during the synthesis, ferrous fluoride (FeF₂) was produced as an undesired byproduct in the product powder. The particle size, composition, and crystalline structure have been characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and X-ray photoelectron spectroscopy (XPS). Results of magnetization measurements for small iron nanoparticles (about 5 nm diameter) are also presented, showing superparamagnetic behavior at room temperature, and a blocking temperature near 125 K.     

Fabrication of flower-shaped Bi2O3 superstructure by a facile template-free process

A novel flower-shaped Bi₂O₃ superstructure has been successfully synthesized by calcination of the precursor, which was prepared via a citric acid assisted hydrothermal process. The precursor and Bi₂O₃ were characterized with respect to morphology, crystal structure and elemental chemical state by field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). It was shown that both the precursor and Bi₂O₃ flower-shaped superstructure were constructed of numerous nanosheets while the nanosheets consisted of a great deal of nanoparticles. Furthermore, key factors for the formation of the superstructures have been proposed; a mechanism for the growth of the superstructure has been presented based on the FESEM investigation of different growth stages.     

Fabrication of chain-like Mn2O3 nanostructures via thermal decomposition of manganese phthalate coordination polymers

A novel manganese coordination polymer [Mn(Pht)(H₂O)]_n as a precursor was obtained by chemical precipitation involving an aqueous solution of anhydrous manganese acetate and phthalate anion as a potential O-banded ligand. Fourier transform infrared (FT-IR) results proved that phthalate anions coordinate to metal cations as a chelating bidentate ligand, making polymeric structure. The Mn₂O₃ nanostructures have been prepared via thermal decomposition of as-prepared manganese phthalate polymers as precursor in the presence of oleic acid (OA) and triphenylphosphine (TPP) as a stabilizer and capping. Different approaches such as FT-IR, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were applied to characterize the products. TEM images and XRD analysis indicated that the as-synthesized chain-like Mn₂O₃ has a crystal phase of cubic syngony with a mean size of ∼40 nm.     

压力对纳米CoFe2O4/SiO2复合材料结构的影响

 采用溶胶-凝胶工艺和高温高压实验技术,制备了纳米CoFe₂O₄/SiO₂复合材料。利用X射线衍射仪、扫描电子显微镜和振动样品磁强计,对样品的结构、微观形貌和磁性进行了研究,并对CoFe₂O₄中阳离子的占位情况进行了讨论。结果表明,随着处理压力的升高,样品的晶粒尺寸增大,晶格常数减小,比饱和磁化强度增大。通过计算结果可以推断,压力的升高导致CoFe₂O₄中的部分Fe³⁺从A位移向了B位,而部分Co²⁺则从B位移向了A位。     

Effect of calcination temperature on the structure and hydroxylation activity of Ni0.5Cu0.5Fe2O4 nanoparticles

Nanocrystalline Ni_0.5Cu_0.5Fe₂O₄ was synthesized by sol-gel method with varying calcination temperature over the range of 500-1000. The powders obtained were characterized by X-ray diffraction (XRD), Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). In addition, thermal analysis (TG-DTG-DTA) of the precursor was carried out. The study reveals the simultaneous decomposition and ferritization process at rather low temperature (280-350). For the crystalline structure investigated, single cubic spinel is gained when the precursor was decomposed at 800-1000, whereas separated crystal CuO formed when calcination temperature is below 800. The increase of calcination temperature favors the appearance of Fe_B³⁺, Cu_A²⁺ and O on the spinel surface. The hydroxylation activity is relative to the amount of Cu_B²⁺ species on the spinel surface. The lattice oxygen species on the spinel surface are favorable for the deep oxidation of phenol.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Temperature controlled synthesis of SrCO3 nanorods via a facile solid-state decomposition rout starting from a novel inorganic precursor

Strontium carbonate nanorods have been successfully synthesized via solid-state decomposition of a new precursor, [Sr(Pht)(H₂O)₂]. The obtained nanorods were found to be orthorhombic with the length of 70-100 nm and the diameter of about 10-15 nm. The Effect of calcinations temperature on morphology and purity of the products has been investigated. Strontium carbonate nanorods were formed at 500 °C. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) spectroscopy. In addition, further evidence for the purity and stoichiometry of the product was obtained by XPS (X-ray photoelectron spectroscopy) spectrum.     

Controlled preparation of unsupported binary and ternary sulfides with high surface area from tetraalkylammonium thiosalts

Unsupported MoS₂, WS₂ and Ni-MoS₂ sulfides have been successfully prepared by decomposition of tetraalkylammonium thiosalts, which were synthesized by using an aqueous solution of tetraalkylammonium halide and ammonium thiosalts at room temperature. The as-prepared samples were characterized by N₂ physorption, thermogravimetric analysis (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results showed that structures and properties of unsupported binary and ternary sulfides depended on tetraalkylammonium thiosalts and decomposition conditions. The samples formed by decomposition of methyl and cetyltrimethyl substituted ammonium thiosalts exhibited high specific surface areas of above 100 m²/g, indicating the organic ligand in the precursor can tune the structure of the binary and ternary sulfides. MoS₂ and Ni-MoS₂ prepared from TMetATM and Ni/TMetATM had a relative narrow distribution in mesoporous range. TEM and XRD results revealed that the unsupported binary and ternary sulfides consisted of few-stacked layers and Ni was well-dispersed on MoS₂.     

Fabrication of porous BaSnO3 hollow architectures using BaCO3@SnO2 core-shell nanorods as precursors

We present a strategy to synthesize porous BaSnO₃ hollow architectures with that were 150-300 nm in diameter and 1.5-5 μm in length using precursor of BaCO₃@SnO₂ nanorods prepared by hydrothermal treatment. BaCO₃@SnO₂ nanorods, consisting of a BaCO₃ core and a SnO₂ shell, could be used effectively for the solid-state synthesis of polycrystalline BaSnO₃ powder at 800 °C (lower than convention for BaCO₃ and SnO₂ mixtures). The core/shell structure of the precursor could play a role as a structural directing template for preparing BaSnO₃ hollow architectures during the calcination process. The X-ray diffractometer (XRD), scanning electron microscope (SEM), and transmission electron microscope (TEM) are employed to characterize the structures and morphologies. When applied to DSSC, the porous BaSnO₃ hollow architectures exhibit distinct photovoltaic effect.     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.