高功率808nm InGaAsP—GaAs分别限制结构的半导体激光器

介绍了研究分别限制结构ＩｎＧａＡｓＰ－ＧａＡｓ半导体激光器所得到的最新成果。利用引进的俄国技术，基于量子阱结构的ＩｎＧａＡｓＰ－ＧａＡｓ激光器，可用短时间液相外延技术制造。在ＧａＡｓ衬底上制成的ＩｎＧａＡｓＰ－ＧａＡｓ分别限制结构的激光器，主要参数如下：发射波入λ＝８０８ｎｍ，阈值电流密度Ｊ＝３００Ａ／ｃｍ＾２，对于条宽ω＝１００μｍ的激光器，连续功率为１－２Ｗ。     

1MeVSi~＋衬底加温注入Al＿（0．3）Ga＿（0．7）As／GaAs超晶格和GaAs的晶格损伤研究

用卢瑟福背散射／沟道技术研究了１ＭｅＶＳｉ￣＋在衬底加温和室温下以不同剂量注入Ａｌ＿（０．３）Ｇ＿（０．７）Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ后的晶格损伤。在衬底加温下，观察到Ａｌ＿（０．３）Ｇａ＿（０．７）Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ都存在一个动态退火速率与缺陷产生速率相平衡的剂量范围，以及两种速率失去平衡的临界剂量。超晶格比ＧａＡｓ更难以损伤，并且它的两种速率失去平衡的临界剂量也大于ＧａＡｓ中的相应临界剂量，用热尖峰与碰撞模型解释了晶格损伤积累与注入剂量和衬底温度的关系。用ＣＮＤＯ／２量子化学方法计算了ＧａＡｓ和Ａｌ＿ｘＧａ＿（１－ｘ）Ａｓ中化学键的相对强度，并根据计算结果解释了注入过程中Ａｌ＿（０．３）Ｇａ＿（０．７）Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ中晶格损伤程度的差别。     

1MeV Si+衬底加温注入Al0.3Ga0.7As/GaAs超晶格和GaAs的晶格损伤研究

用卢瑟福背散射／沟道技术研究了１ＭｅＶＳｉ⁺在衬底加温和室温下以不同剂量注入Ａｌ_0.3Ｇ_0.7Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ后的晶格损伤。在衬底加温下，观察到Ａｌ_0.3Ｇａ_0.7Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ都存在一个动态退火速率与缺陷产生速率相平衡的剂量范围，以及两种速率失去平衡的临界剂量。超晶格比ＧａＡｓ更难以损伤，并且它的两种速率失去平衡的临界剂量也大于ＧａＡｓ中的相应临界剂量，用热尖峰与碰撞模型解释了晶格损伤积累与注入剂量和衬底温度的关系。用ＣＮＤＯ／２量子化学方法计算了ＧａＡｓ和Ａｌ_xＧａ_1-xＡｓ中化学键的相对强度，并根据计算结果解释了注入过程中Ａｌ_0.3Ｇａ_0.7Ａｓ／ＧａＡｓ超晶格和ＧａＡｓ中晶格损伤程度的差别。 关键词：     

Ga1—xAlxAs外延片有源区Al组份的测定方法

由于ＧａＡｓ与ＡｌＡｓ晶格常数相近，ＧａＡｓ晶格常数为０．５６５３５ｎｍ，ＡｌＡｓ的晶格常数为０．５６６０５ｎｍ，当固熔体中Ａｌ组份ｘ值从０变到１时，晶格常数变化约为０．１５％．因此，在ＧａＡｓ衬底上生长Ｇａ１－ｘＡｌｘＡｓ时，在界面处的失配位错少，...     

GaAs衬底上生长的GaInP_2外延单晶薄膜的杂质污染研究

各种外延技术已被用来在ＧａＡｓ衬底上生长ＧａｘＩｎ１－ｘＰ外延单晶薄膜（ＧａＩｎＰ２／ＧａＡｓ）．很多文献认为,在ＧａＩｎＰ２／ＧａＡｓ生长过程中会被Ｃ杂质污染．我们用高灵敏的ＣＡＭＥＣＡＩＭＳ４Ｆ型二次离子质谱仪直接测量的结果表明,污染ＧａＩｎＰ２／ＧａＡｓ的微量杂质是Ｓｉ,而不是Ｃ．由ＧａＩｎＰ２／ＧａＡｓ在１．１７ｅＶ附近的光致发光峰的峰值随激发强度的变化形状表明了它应属于施主－受主对复合发光．进一步分析表明,施主为处在Ｇａ格位上的Ｓｉ杂质（ＳｉＧａ）,受主为Ｇａ空位（ＶＧａ）．     

退火及铟含量对InGaAs量子点光学特性的影响

研究了退火条件和 Ｉｎ 组份对分子束外延生长的 Ｉｎ Ｇａ Ａｓ 量子点（分别以 Ｇａ Ａｓ或 Ａｌ Ｇａ Ａｓ 为基体）光学特性的影响。表明：量子点中 Ｉｎ 含量的增加将导致载流子的定域能增加和基态与激发态之间的能量间隔增大。采用垂直耦合的量子点及宽能带的 Ａｌ Ｇａ Ａｓ 基体可增强材料的热稳定性。以 Ａｌ Ｇａ Ａｓ 为基体的 Ｉｎ Ｇａ Ａｓ 量子点,高温后退火工艺 （ Ｔ＝ ８３０℃）可改善低温生长的 Ａｌ Ｇａ Ａｓ 层的质量,从而改善量子点激光器材料的质量。     

垂直电子耦合InGaAs量子吉的光学特性

报导了ＩｎＧａＡｓ／ＧａＡｓ和ＩｎＧａＡｓ／ＡｌＧａＡｓ垂直耦合量子结在注入式激光器的制备工艺及其光致荧光谱，量热吸收谱和电致荧光谱的特性，该激光器的连续波波发光功率在室温下可达１Ｗ。     

The Reactions of Nickel ion with n-Alkane in the Gas Phase

ＴｈｅＲｅａｃｔｉｏｎｓｏｆＮｉｃｋｅｌｉｏｎｗｉｔｈｎ－Ａｌｋａｎｅｉｎｔｈｅ　ＧａｓＰｈａｓｅＴｈｅＲｅａｃｔｉｏｎｓｏｆＮｉｃｋｅｌｉｏｎｗｉｔｈｎ－ＡｌｋａｎｅｉｎｔｈｅＧａｓＰｈａｓｅ￥ＺＨＡＮＧＢｉｎｇ；ＺＨＡＮＧＦｅｉｈｕａ；ＪＩＹｕｆ...     

Birefringence of (Al)GaAs/AlGaAs multiplequantum well optical waveguides

Ｂｉｒｅｆｒｉｎｇｅｎｃｅｏｆ（Ａｌ）ＧａＡｓ／ＡｌＧａＡｓｍｕｌｔｉｐｌｅｑｕａｎｔｕｍｗｅｌｌｏｐｔｉｃａｌｗａｖｅｇｕｉｄｅｓ￥ＭＡＣｈｕｎｓｈｅｎｇ（ＤｅｐａｒｔｍｅｎｔｏｆＥｌｅｃｔｒｏｎｉｃＥｎｇｉｎｅｅｒｉｎｇ，ＮａｔｉｏｎａｌＩｎｔｅ...     

汽─液─固相法生长GaAs／InAs量子点

汽─液─固相法生长ＧａＡｓ／ＩｎＡｓ量子点１９９５年４月，日本《固体物理》第３０卷第３９９页发表的比留间健之等的文章介绍了汽－液－固相法生长的ＧａＡｓ／ＩｎＡｓ量子点及其光荧光蓝移现象。在以Ａｓ终止的ＧａＡｓ（１１１）面上真空蒸发约１ｎｍ的Ａｕ膜，加...     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.