Structure,mechanical characteristics,and deformation and fracture features of quenched structural steel under static and cyclic loading after combined strain-heat nanostructuring treatment

In the work, we studied the special features of deformation and fracture of quenched steel 50 (0.51%) under static and cyclic tension after combined strain-heat nanostructuring treatment, which includes fictional treatment with subsequent tempering at 350°C. It is shown that the combined nanostructuring treatment of quenched steel 50 changes the character of plastic flow, making it more uniform, in the loaded material. Under static tension, this shows up as disappearance of the yield plateau early in the process, and under cyclic loading, as suppression of the deformation relief formed by shear and rotational deformation modes. Despite incipient cracks, the hardened surface layer thus escapes complete fracture throughout the fatigue loading and preserves its resistance to mechanical contact action.     

Application of aluminum foil for “strain sensing” at fatigue damage evaluation of carbon fiber composite

Surface layer of a loaded solid is an individual structural level of deformation that was shown numerously within concept of physical mesomechanics.This gives rise to advance in its deformation development under loading as well as allows using this phenomenon to sense the strain induced structure changes.It is of specific importance for composite materials since they are highly heterogeneous while estimating their mechanical state is a topical applied problem.Fatigue tests of carbon fiber composite specimens were carried out for cyclic deformation estimation with the use of strain sensors made of thin(80μm)aluminum foil glued to the specimen’s surface.The surface images were captured by DSLR camera mounted onto an optical microscope.Strain relief to form during cyclic loading was numerically estimated using different parameters:dispersion,mean square error,universal image quality index,fractal dimension and energy of Fourier spectrum.The results are discussed in view of deformation mismatch in thin foil and bulk specimen and are offered to be applied for the development of Structural Health Monitoring(SHM)approach.     

Prediction of the effect of plastic-strain stabilization under cyclic deformation based on the structural‒temporal approach

On the basis of modification of the relaxation model of plasticity developed previously for the case of single loading, a new model of cyclic deformation is formulated. It is shown that the introduction of only one constant time parameter dependent on the material structure makes it possible to compose a simple calculation scheme of accumulation of residual strains under multiple cycling of samples.     

Structural effects of three-dimensional angle-interlock woven composite undergoing bending cyclic loading

This paper reports the structural effects of three-dimensional (3-D) angle-interlock woven composite (3DAWC) undergoing three-point bending cyclic loading from experimental and finite element analysis (FEA) approaches. In experiment, the fatigue tests were conducted to measure the bending deflection and to observe the damage morphologies. By the FEA approach, a micro-structural unit-cell model of the 3DAWC was established at the yarn level to simulate the fatigue damage. The stress degradation at the loading condition of constant deformation amplitude was calculated to show the degradation of mechanical properties. In addition, the stress distribution, fatigue damage evolution and critical damage regions were also obtained to qualitatively reveal the structural effects and damage mechanisms of the 3DAWC subjected to three-point bending cyclic loading.     

Microplastic deformation of polycrystals during cyclic loading

A model of microplastic deformation of polycrystals during zero-start cyclic loading with tensions lower than the yield strength is proposed according to which during cycling, thermally activated movement of dislocations occurs under conditions of stress relaxation. Based on this model and the statistical theory of polycrystalline microdeformation, the accumulation of microplastic deformation is theoretically described as a function of the number of loading cycles and the stress amplitudes. It is theoretically proved that in the cycling process the microplastic deformation that accumulates over one cycle decreases as the number of cycles increases; up to the macroscopic elastic limit it is independent of the stress amplitude, and then sharply increases. Agreement of the theory with experimental data for spring alloys is observed in the density of mobile dislocations, which decreases during cycling.Translated from Izvestiya Vysshikh Uchebnykh Zavedenii, Fizika, No. 3, pp. 29–34, March, 1990.     

Effects of Ultrasonic Surface Treatment on the Structure and Properties of Polycrystalline and Nanostructured Titanium

The effects of ultrasonic surface treatment on the structural and phase-state of subsurface layers of polycrystalline and ultrafine-grained titanium are investigated. The changes in microhardness, mechanical properties, and regularities of microplastic deformation buildup are studied under static and cyclic loading. It is found that the characteristics of polycrystalline titanium suffer most from the ultrasonic treatment, while its influence on ultrafine-grained titanium is considerably weaker.     

Modeling microstructure evolution of binary systems subjected to irradiation and mechanical loading

We study a change in mechanical properties of binary systems subjected to irradiation influence described by ballistic flux of atomic mixing having regular and stochastic contributions. By using numerical modeling based on the phase field approach we study dynamics of deformation fields in a previously irradiated system and in the binary system deformed during irradiation. An influence of both deterministic and stochastic components of ballistic flux onto both yield strength and ultimate strength is studied. We have found that degradation of mechanical properties relates to the formation of percolating clusters of shear bands. Considering a hardening coefficient we analyze stages of plastic deformation of both initially irradiated alloy and alloy subjected to sustained irradiation. Stability of binary alloy under mechanical loading in the form of shear strain with a constant rate and cyclic deformation is discussed.     

温度对超薄铜膜疲劳性能影响的分子动力学模拟

用嵌入原子势的分子动力学方法模拟了温度对超薄铜膜疲劳性能的影响. 通过模拟, 首先给出了超薄铜膜的总能及应力随循环周次的变化曲线; 根据叠加经验式得出的叠加量随循环周次变化曲线, 判断出各种恒定温度下超薄铜膜的疲劳寿命. 由 200–400 K温度范围内超薄铜膜的疲劳寿命-温度变化曲线, 可以发现存在两个温度区域: 在约370 K以下, 超薄铜膜的疲劳寿命随温度升高缓慢增加, 而在约370 K以上增加较快. 建立了模型并用位错演化机制解释了超薄铜膜疲劳寿命的温度依赖关系. 关键词： 分子动力学 疲劳 温度效应 位错     

Stress-based crystal analysis of yielding in rolled Mg AZ31B

A stress-based analysis is demonstrated that can be used to evaluate the effect of material orientation and loading conditions on the micro- and macro-scale yield response of strongly textured metals. This analysis is used to construct microscale yield surfaces for selected deformation mechanisms in rolled AZ31B. Two-dimensional projections of these surfaces are plotted along sample directions to quantify the relative activity of each mechanism for various loading conditions. By assigning each mechanism realistic strengths, the analysis is used to quantify the influence of each deformation mechanism on macroscale yield behaviour. Due to its simplicity, this analysis can be easily carried out to probe and visualize projections of material response in any part of stress space given the material’s texture, its relevant deformation mechanisms and realistic initial strengths of these mechanisms.     

碳纤维增强复合材料层合板的抗冲击性能

为了研究碳纤维增强环氧树脂基复合材料层合梁的抗冲击性能,应用金属泡沫弹撞击加载的方式,结合高速摄像机,对等厚度层合梁结构的动态响应和失效行为展开实验研究。研究不同冲击加载强度对层合梁的动态失效过程、变形轮廓、中点变形、失效模式及能量耗散比的影响。结果表明:随着冲击强度的增加,中点变形响应速度随之增加,层合梁变形模式由整体变形转变为局部变形,且局部化效应随之增加,并伴随严重的基体和纤维断裂失效。层合梁能量耗散比随冲击强度的增加而增加,并展现出与结构失效模式直接关联的弹性变形、中心断裂和完全失效3个不同阶段。     

Hardening and softening during fatigue fracture

Summary The comparison of the change of hardness and plastic deformation amplitude at a constant stress loading or stress amplitude at a constant deformation loading during the fatigue process shows some singularity of the hardening and softening effects. These effects were investigated on mean carbon and low-alloyed steel and on globular cast iron.The fatigue fractures at cycle numbers 10⁴÷10⁶ under stresses below the yield strength predominate in the softening process, which arises after an inconsiderable hardness increase extends in the region to 0·2 from the fracturing cycle number. Under the stresses above the yield strength, which in some cases for annealed and coarse-grained states are below the fatigue limit, the hardening process predominates, followed by a hardness increase in the field up to 0·25 and above the fracturing cycle number.At low cycle fatigue fractures with cycle numbers < 10⁴ depending on the cyclic plastic properties of steels the fatigue process can be followed by a continuous hardening or softening till fracture. This process is characterized by the change of the deformation amplitude and a one-sided accumulation of plastic deformations at a constant amplitude of active stresses. The one-sided accumulation of deformations commonly ends in a quasistatic failure. Under loading with a constant deformation amplitude during softening a fatigue fracture takes place as a result of damage accumulation under the alternating stresses with amplitudes decreasing with cycle number.     

固支方板对水中爆炸作用的动态响应研究

 分析研究了在装药水中爆炸产生的强冲击载荷作用下固支方板的塑性动力响应过程。通过对水中爆炸理论和板的大变形理论分析，应用能量原理和Lagrangian函数，推导出反映固支方板在冲击载荷作用下变形的最终挠度的解析解。水中爆炸对固边方板破坏的实验在自制的水箱中进行。对不同的装药重量和炸距情况下方板的变形情况进行了理论计算，并对实验结果和误差来源进行了分析。实验结果和理论结果具有较好的一致性。     

Cyclic deformation and fatigue cracking behaviour of polycrystalline Cu,Cu–10 wt% Zn and Cu–32 wt% Zn

The cyclic deformation behaviour of polycrystalline Cu, Cu–10 wt% Zn and Cu–32 wt% Zn was systematically investigated in the plastic strain amplitude range of 1 × 10^?4–4 × 10^?3. The differences in the cyclic stress–strain (CSS) responses and fatigue cracking behaviour between Cu, Cu–10 wt% Zn and Cu–32 wt% Zn were compared. It was found that the occurrence of a cyclic saturation for Cu–10 wt% Zn and Cu–32 wt% Zn strongly depends on the applied strain amplitude, whereas polycrystalline Cu always displays cyclic saturation. Surface deformation morphologies were analyzed by scanning electron microscopy (SEM). One of the major features observed is that the slip bands become increasingly homogenous with Zn addition. The fatigue cracks were found to frequently nucleate along the annealing twin boundaries (TBs) in Cu–10 wt% Zn and Cu–32 wt% Zn, but not in polycrystalline Cu. Based on these experimental results, the cyclic deformation response and fatigue cracking behaviour are discussed, and a developed TB cracking mechanism is proposed to explain the difference in fatigue cracking mechanisms in Cu, Cu–10 wt% Zn and Cu–32 wt% Zn.     

A physical interpretation of softening of pressure-sensitive and anisotropic materials

Several new dynamic models are proposed to explain the mechanical behaviour of softening of pressure-sensitive and anisotropic materials at a macroscopic level. If a pressure-sensitive material is loaded by a force and a variable pressure or an anisotropic material is subjected to a load with a changeable loading direction relative to the material frame, their stress–strain relationships become more complicated. Mechanical behaviours of these stress–strain relationships have to cover the feature concerning the change of pressure or loading direction, i.e. mechanical properties of pressure-sensitive material corresponding to different pressure state or anisotropic material relating to different loading direction will play an important role in deciding their stress–strain relationships. Such shift of material properties due to the variable pressure or loading history may significantly expand the traditional concept of the stability of material deformation, and the second order of plastic work being negative may be a response of stable plastic deformation, which is commonly called softening.     

高温、高压、高应变速率动态过程晶体塑性有限元理论模型及其应用

对于高温、高压、高应变速率加载条件下的材料冲击变形行为,动态晶体塑性模型能够直接反映晶体中塑性滑移的各向异性及其对温度、压力和微观组织结构的依赖性,因而广泛应用于材料的动态冲击力学响应、微观结构演化以及动态损伤破坏的模拟。本文综述了高压冲击下动态晶体塑性有限元的理论模型,主要包括变形运动学、包含状态方程的超弹性本构模型和晶体塑性本构模型,涉及位错滑移、相变、孪生等塑性变形机制,以及层裂、绝热剪切带等动态破坏方式。     

Cyclic stress-strain curves and internal friction of steel at ultrasonic frequencies

A new interpretation of some characteristics of material push-pull loaded at a frequency of 23 kHz can be evaluated by measuring the internal friction and elasticity modulus defect at different strain amplitudes. It is possible to obtain interesting relations describing the material's cyclic microplasticity response. The paper presents some basic relationships between the ‘plastic’ internal friction, elasticity modulus defect, hysteresis loop area, plastic strain amplitude and the cyclic deformation hardening coefficient, for low carbon steel with different grain sizes.     

Nanocrack nucleation in polycrystalline silicon during grain-boundary sliding

A theoretical model is proposed to describe nanocrack nucleation in polycrystalline silicon. In terms of this model, nanocrack nucleation is stimulated by grain-boundary sliding, which creates sources of local stresses in triple junctions of grain boundaries. The relaxation of these local stresses is the main driving force of nanocrack nucleation near triple junctions in polycrystalline silicon, in which grain-boundary sliding contributes substantially to plastic deformation under cyclic loading at room temperature. The model is used to calculate the critical external stress required for nanocrack nucleation in polycrystalline silicon.     

Effect of dynamic stress state perturbation on irreversible strain accumulation at interfaces in block-structured media

The paper studies how the stress state of the interface between structural elements in a block-structured medium affects its deformation response to dynamic loading. It is shown that the normalized shear stress and mean stress are the major factors that determine the deformation response of the interface. We propose to describe the dependence of the value of induced irreversible displacement at the interface on the normalized shear stress using a logistic function. The central point of this function is the point of transition from the quasi-elastic to quasi-plastic stage of the interface shear deformation. The obtained empirical dependences are important for understanding the mechanism of irreversible strain accumulation in fault zone fragments and, particularly, for the development of an earlier proposed approach to estimate the characteristic level of active shear stresses in separate tectonic fault regions.     

The role of curvature of the crystal structure in the formation of micropores and crack development under fatigue fracture of commercial titanium

The multiscale mechanism of fatigue fracture of titanium with the surface layer hydrogenated under alternating bending at room temperature is studied. It is shown that the generation of the fatigue fracture occurs in the surface layer subjected to plastic deformation in conjunction with an elastically loaded substrate. The latter causes the appearance of a strong curvature of the material and the appearance of micropores in these areas along with any fatigue cracks. The emergence of the local curvature of the crystal structure plays a central role in the origin and the development of the fatigue fracture as the structural phase decomposition of the material under cyclic loading.     

Theory of magnetic shape memory effect and pseudoelastic deformation in Ni-Mn-Ga alloys

The effect of the magnetic field on the deformation behavior of magnetic alloys of the Heusler type under different loading conditions is discussed in terms of the theory of diffuse martensitic transitions. The effects of magnetic shape memory, pseudoelastic deformation, and generation of reactive stresses in response to the magnetic field are considered. The theoretical relationships are compared with the experimental data available in the literature.