Mass transfer in porous systems, flooded in part with water, of gas diffusion and catalytic layers of the cathode of a fuel cell with a solid polymer electrolyte

Mass transfer in porous gas diffusion and catalytic layers of the cathode of a hydrogen-air fuel cell with a solid polymer electrolyte is considered. The transport processes are considered with allowance made for the partial flooding of porous systems of these layers with water, which forms during the fuel cell operation. The consideration also allows for the influence of the diluent gas present when air oxygen is used as the oxidant. The fraction of water-flooded pores is calculated within percolation theory as a function of structural parameters of the porous system. Conditions leading to the beginning of the gas diffusion layer flooding are presented.     

Gas diffusion electrodes for polymer electrolyte fuel cell using sulfonated polyimide

Gas diffusion electrodes for high temperature polymer electrolyte fuel cells (PEFCs) have been prepared by using a novel proton conductive sulfonated polyimide (SPI) electrolyte. The catalyst layer was composed of Pt-loaded carbon black (Pt-CB) and SPI ionomer. The polarization properties and the microstructure of the catalyst layer were investigated as a function of the SPI/CB weight ratio. The anodic polarization was found to be negligibly small for all the compositions examined. The highest cathode performance was obtained at SPI/CB = 0.5 (by weight), where the best balance of high catalyst utilization and oxygen gas diffusion rate through the ionomer was obtained.     

Effect of the fuel electrode composition and structure on the performance of the direct methanol fuel cell

The effect the composition and structure of the active layer of the anode exerts on the performance of the solid-polymer direct methanol fuel cell is studied experimentally. It is shown that the ohmic voltage losses in the layer and the content of the solid polymer electrolyte (SPE) play an important role. The performance of the fuel cells is the best at 20–25 vol % SPE in the layer.     

气体扩散电极参数对阴离子交换膜燃料电池性能的影响

优化了碱性阴离子交换膜燃料电池（AAEMFC）使用的气体扩散电极（GDE）,发现催化层中PTFE含量与催化剂担载量对电池性能与其电化学动力学特征影响很大.采用i-V曲线,开路电压,电池内阻与在线的电化学阻抗谱与动力学分析,评估了所制GDE的电化学性能.在所研究的AAEMFC电极催化层中,PTFE的最佳含量是20%,Pt载量对膜电极三相界面、催化层导电性与催化剂利用率的影响极大.当制备的GDE催化层中Pt/C的Pt载量为1.0mg/cm²,PTFE含量为20%时,AAEMFC的峰电流密度在50^oC达到了213mW/cm².兼顾Pt催化剂的利用率与成本,在没有明显影响电池性能的情况下,Pt的担载量可降至0.5mg/cm².     

An NMR study of methanol diffusion in polymer electrolyte fuel cell membranes

Methanol diffusion in two polymer electrolyte membranes, Nafion 117 and BPSH 40 (a 40% disulfonated wholly aromatic polyarylene ether sulfone), was measured using a modified pulsed field gradient NMR method. This method allowed for the diffusion coefficient of methanol within the membrane to be determined while immersed in a methanol solution of known concentration. A second set of gradient pulses suppressed the signal from the solvent in solution, thus allowing the methanol within the membrane to be monitored unambiguously. Over a methanol concentration range of 0.5–8 M, methanol diffusion coefficients in Nafion 117 were found to increase from 2.9 × 10⁻⁶ to 4.0 × 10⁻⁶ cm² s⁻¹. For BPSH 40, the diffusion coefficient dropped significantly over the same concentration range, from 7.7 × 10⁻⁶ to 2.5 × 10⁻⁶cm² s⁻¹. The difference in diffusion behavior is largely related to the amount of solvent sorbed by the membranes. Increasing the methanol concentration results in an increase in solvent uptake for Nafion 117, while BPSH 40 actually excludes the solvent at higher concentrations. In contrast, diffusion of methanol measured via permeability measurements (assuming a partition coefficient of 1) was lower (1.3 × 10⁻⁶ and 6.4 × 10⁻⁷ cm² s⁻¹ for Nafion 117 and BPSH 40 respectively) and showed no concentration dependence. The differences observed between the two techniques are related to the length scale over which diffusion is monitored and the partition coefficient, or solubility, of methanol in the membranes as a function of concentration. For the permeability measurements, this length is equal to the thickness of the membrane (178 and 132 μm for Nafion 117 and BPSH 40 respectively) whereas the NMR method observes diffusion over a length of approximately 4–8 μm. Regardless of the measurement technique, BPSH 40 is a greater barrier to methanol permeability at high methanol concentrations.     

Cathode of a fuel cell with a solid polymer electrolyte: Calculating overall currents in the presence of a gas-diffusion layer

Mathematical apparatus, which makes it possible to perform calculations of the current-voltage characteristics of cathodes of fuel cells with a solid polymer electrolyte in conditions where there are present extraneous diffusion restrictions is proposed. In so doing, the partial pressure of oxygen and the absolute pressure of gas in the gas chamber may assume any values. First of all presented are the results of calculations of the current-voltage characteristics intrinsic to active layers of the air and oxygen cathodes, which are performed under the assumption that the extraneous diffusion restrictions are absent altogether. Thereafter, in the same conditions (at the same parameters that characterize the active layer of a cathode), obtained are results of a calculation of the current-voltage characteristics inherent in the air and oxygen cathodes in the presence of extraneous diffusion restrictions. Afterward there is performed an analysis of the way a gas-diffusion layer restricts the process of generation of current in a cathode and of what measures should be taken in order for the extraneous diffusion restrictions to become less significant.     

Active layer of the cathode of a fuel cell with a solid polymer electrolyte: The effect of the Nafion concentration on the overall characteristics

A computer-aided simulation of the structure of the active layer of the cathode of a fuel cell with a solid polymer electrolyte (Nafion) is performed under the assumption about equidimensionalness of dimensions of grains of the substrate (with platinum crystallites in them) and grains (agglomerates of molecules) of Nafion. It is analyzed how the Nafion concentration affects principal parameters, which include the specific surface area, in the vicinity of which electrochemical process goes on; the effective ionic electroconductivity, and the effective diffusion coefficient of a gas. It is demonstrated how one can determine the Nafion concentration at which the overall current takes on a maximum value. Dependences of the optimum value of the overall current and the thickness of the active layer and the weight of platinum, which correspond to it, on the Nafion concentration are calculated. It is demonstrated that there in principle cannot exist one individual optimum concentration of Nafion, which is suitable for all techniques used for the preparation of the active layer. The mutual relationship between values of the effective diffusion coefficient of a gas and the effective ionic electroconductivity of Nafion determines the value of the optimum of the Nafion concentration.     

燃料电池聚合物电解质膜的研究进展

本文根据聚合物电解质膜燃料电池操作温度、使用的电解质和燃料的不同,将其分为高温质子交换膜燃料电池、低温质子换膜燃料电池、直接甲醇燃料电池和阴离子交换膜燃料电池,综述了它们所用电解质膜的最新进展.第一部分简要介绍了这4种燃料电池的优点和不足.第二部分首先介绍了Nafion膜的结构模型,并对平行柱状纳米水通道模型在介观尺度上进行了修正;接着分别对应用于不同燃料电池的改性膜的改性思路作了分析;最后讨论了用于不同燃料电池的新型质子交换膜的研究,同时列举了性能突出的改性膜和新型质子交换膜.第三部分介绍了阴离子交换膜的研究现状.第四部分对未来聚合物电解质膜的研究作了展望.     

Synthesis and test of palladium-based nanostructured anodic electrocatalysts for hydrogen fuel cells with solid polymer electrolyte

Palladium-based nanostructured electrocatalysts on the Vulcan XC-72 carbon support for fuel cells with solid polymer electrolyte are synthesized and studied. In particular, electrochemical studies of the synthesized catalysts are carried out and membrane-electrode assemblies are assembled on their basis and tested. The test results indicate that platinum can be replaced with palladium in the hydrogen electrode of the fuel cells.     

Optimization of Mass Transfer Processes in the Zone of the Air Electrode of a Fuel Cell with a Solid Polymer Electrolyte

A two-dimensional mathematical model for the transport of reactants in a fuel cell with a solid polymer electrolyte is developed. The model is used for analyzing spatial distributions of the concentration of reactants and current density over the cell. The effect of the catalytic-layer activity, reactant speed, bipolar-plate geometry, thickness and porosity of current collector and/or gas-diffusion sublayer, and the reaction mixture composition on the fuel cell efficiency is estimated theoretically and experimentally.     

Mechanical endurance of polymer electrolyte membrane and PEM fuel cell durability

The life of proton exchange membrane fuel cells (PEMFC) is currently limited by the mechanical endurance of polymer electrolyte membranes and membrane electrode assemblies (MEAs). In this paper, the authors report recent experimental and modeling work toward understanding the mechanisms of delayed mechanical failures of polymer electrolyte membranes and MEAs under relevant PEMFC operating conditions. Mechanical breach of membranes/MEAs in the form of pinholes and tears has been frequently observed after long‐term or accelerated testing of PEMFC cells/stacks. Catastrophic failure of cell/stack due to rapid gas crossover shortly follows the mechanical breach. Ex situ mechanical characterizations were performed on MEAs after being subjected to the accelerated chemical aging and relative humidity (RH) cycling tests. The results showed significant reduction of MEA ductility manifested as drastically reduced strain‐to‐failure of the chemically aged and RH‐cycled MEAs. Postmortem analysis revealed the formation and growth of mechanical defects such as cracks and crazing in the membranes and MEAs. A finite element model was used to estimate stress/strain states of an edge‐constrained MEA under rapid RH variations. Damage metrics for accelerated testing and life prediction of PEMFCs are discussed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2346–2357, 2006     

Improving protonic conduction of membranes for polymer electrolyte fuel cells

Method for the modification of proton-conducting Nafion membranes by using a zirconium citrate one-substituted salt, aimed at the improving of characteristics of membranes for polymer-electrolyte-based fuel cells, is suggested. In the method, the membrane is impregnated first with zirconyl chloride and then with citric acid; an insoluble sol is thus formed in the membrane pores. The impregnation is carried out in ultrasound bath, using an isopropyl alcohol-water solvent, to make it more rapid and uniform. It is shown that the impregnation lowers the real component of the membrane impedance. The discharge characteristics of the impregnated and nonimpregnated membranes are compared.     

Gas diffusion hindrances on Ni cermet anode in contact with Zr<Subscript>0.84</Subscript>Y<Subscript>0.16</Subscript>O<Subscript>1.92</Subscript> solid electrolyte

The electrochemical behavior of Ni cermet electrode with CeO_{2 ? x} additive in contact with YSZ electrode was studied by means of impedance spectroscopy in H₂, H₂O, CO₂, CO, He, and Ar gas media of various composition within the temperature range of 700 to 950°C. Near the equilibrium potential, the electrochemical impedance spectra of the studied electrodes indicate to three stages of electrode reaction. The polarization conductivity of the low-frequency stage of electrode reaction (σ_lf) is characterized with the following regularities: (a) temperature dependence of σ_lf has a positive slope in Arrhenius coordinates; (b) σ_lf increases upon replacement of gas mixture with lower mutual diffusion coefficient by mixture with higher mutual diffusion coefficient, while polarization conductivity values of other stages remain practically invariable; (c) concentration relationships of 1/σ_lfrecorded for constant activity of oxygen in the gas phase are linear in the 1/σ_lf vs. 1/P _{CO 2} (P _CO) coordinates; (d) no low-frequency stage of the electrode reaction is observed upon electrochemical inflow (outflow) of the gas reagents (reaction products) to (from) the test electrodes (current passing through closely pressed specimens and central specimen impedance measurement); and (e) no change in the gas flow rate affects σ_lf value. The observed regularities were explained by assuming the gas diffusion nature of the low-frequency stage of the electrode reaction. The gas diffusion layer thickness was estimated.     

Nanoscale membrane electrode assemblies based on porous anodic alumina for hydrogen–oxygen fuel cell

In this paper, we demonstrate that nanoscale membrane electrode assemblies, functioning in a H₂/O₂ fuel cell, can be fabricated by impregnation of anodic alumina porous membranes with Nafion® and phosphotungstic acid. Porous anodic alumina is potentially a promising material for thin-film micro power sources because of its ability to be manipulated in micro-machining operations. Alumina membranes (Whatman, 50 μm thick, and pore diameters of 200 nm) impregnated with the proton conductor were characterized by means of scanning electron microscopy, X-ray diffraction, and thermal analysis. The electrochemical characterization of the membrane electrode assemblies was carried out by recording the polarization curves of a hydrogen–oxygen 5 cm² fuel cell working at low temperatures (25?÷?80 °C) in humid atmosphere. Our assemblies realized with alumina membranes filled with phosphotungstic acid and Nafion® reach respectively the peak powers of 20 and 4 mW/cm² at room temperature using hydrogen and oxygen as fuel and oxidizer.     

Chemical stability enhancement of crown ether grafted sulfonated poly(arylene ether ketone) fuel cell membrane by cerium ion fixation

In operation of polymer electrolyte membrane fuel cell or direct methanol fuel cell, ·OH radicals are the major cause for the degradation of polymer electrolyte membrane. In order to enhance its antioxidation stability, cerium ion (Ce³⁺, CE), an ·OH radical quencher, is introduced to membrane, as it converts the ·OH radicals into inactive chemicals. In this study, aminoethyl‐15‐crown‐5 (CRE) is grafted on the sulfonated poly(arylene ether ketone) (SPAEK) to prevent the migration of CE ions from the membrane for long‐term antioxidation stability, as CRE forms a coordination complex with CE. The chemical and physical structures of the CRE grafted SPAEK are examined using proton nuclear magnetic resonance, energy dispersive X‐ray, and small‐angle X‐ray scattering spectroscopy. The physical properties of the CRE grafted SPAEK membrane are investigated and compared with those of the CRE blended and CE blended ones. While the grafting of CRE does not significantly affect the thermal and mechanical and water uptake behaviors of membranes, it leads to a significant improvement of antidegradation effect compared with other blend systems according to Fenton's test. The proton conductivity decreases with addition of CE but its effect is lessened by introduction of CRE. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 101–109     

Improving the efficiency of a direct ethanol fuel cell by a periodic load change

We present a simple method to increase the efficiency of a direct ethanol fuel cell by a periodic modulation of the load (pulsed mode). The fuel cell was periodically short circuited with a resistor (1...     

周期性负载变化提高乙醇燃料电池效率(英文)

We present a simple method to increase the efficiency of a direct ethanol fuel cell by a periodic modulation of the load(pulsed mode). The fuel cell was periodically short circuited with a resistor(1 Ω) for a few seconds(high load period) followed by a low load period of up to 100 s when the resistor was disconnected. The open circuit voltage(OCV) values before and after the short circuit of the cell showed an increase of up to 70 mV. The higher OCV was due to the oxidation and removal of strongly adsorbed CO during the electric short circuit when the electric potential of the anode was increased to be close to the cathode potential. The depoisoned anode surface was much more active directly after the short circuit. The slow decrease of the OCV observed after the short circuit was caused by the subsequent poisoning of the anode surface, which can be neutralized by another short circuit. In general, a stable increase in cell performance was obtained by repetition of the electric short circuit. The data showed that the pulse mode gave an increase in the power generated by the direct ethanol fuel cell by up to 51% and was 6% on average. It is anticipated that this mode of operation can be used also in different types of polymer electrolyte membrane fuel cells where CO poisoning is a problem, and after optimization of the parameters, a much higher gain in efficien-cy can be obtained.     

Sulfonated poly(ether ether ketone)/poly(vinylpyrrolidone) acid–base polymer blends for direct methanol fuel cell application

Acid–base polymer blends for polymer electrolyte membranes have been prepared by blending sulfonated poly(ether ether ketone) (SPEEK) with poly(vinylpyrrolidone) (PVP) to reduce methanol uptake and to decrease methanol permeability while maintaining high proton conductivity. The acid‐base interaction occurring on the sulfonic acid group and on the tertiary amide group was characterized by FTIR and DMA. As the composition of PVP lowered than 20 wt % in the blends, the acid–base interaction causes great reduction on methanol uptake and the methanol permeability; however, the proton conductivity is still high. In this work, membrane–electrode assemblies (MEAs) have been prepared for direct methanol fuel cell (DMFC) from both blend membrane and Nafion 117. DMFC single cell performance was also evaluated. Results confirmed that SPEEK (with the degree of sulfonation (DS) = 69%) blended with PVP (M_n = 1,300,000) with a ratio of 80/20 (w/w) exhibits higher open‐circuit voltages (OCV) and lower polarization loss than those of Nafion 117. These acid–base blends will be suitable for DMFC application. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 565–572, 2006     

Nanostructure and properties of sulfonated polyarylenethioethersulfone copolymers as proton exchange fuel cell membranes

A systematic investigation of properties and nanostructure of sulfonated polyarylenethioethersulfone (SPTES) copolymer proton exchange membranes for fuel cell applications has been presented. SPTES copolymers are high temperature resistant (250 °C), and form tough films with excellent proton conductivity up to 170 ± 5 mS/cm (SPTES 70 @ 85 °C, 85%RH). Small angle X‐ray scattering of hydrated SPTES 70 revealed the presence of local water domains (diameter ～5 nm) within the copolymer. The high proton conductivity of the membranes is attributed to the formation of these ionic aggregates containing water molecules, which facilitate proton transfer. AFM studies of SPTES 70 as a function of humidity (25–65%RH) showed an increase in hydrophilic domains with increasing humidity at 22 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2813–2822, 2007