Determination of polyphenols in oats by near-infrared spectroscopy (NIRS) and two-dimensional correlation spectroscopy

Two-dimensional correlation spectroscopy (2DCOS) and near-infrared spectroscopy (NIRS) were used to determine the polyphenol content in oat grain. A partial least squares (PLS) algorithm was used to perform the calibration. A total of 116 representative oat samples from four locations in China were prepared and the corresponding near-infrared spectra were measured. Two-dimensional correlation spectroscopy was employed to select wavelength bands for the PLS regression model for the polyphenol determination. The number of PLS components and intervals was optimized according to the coefficients of determination (R²) and root mean square error of cross validation (RMSECV) in the calibration set. The performance of the final model was evaluated using the correlation coefficient (R) and the root mean square error of validation (RMSEV) in the prediction set. The results showed the band corresponding to the optimal calibration model was between 1350 and 1848?nm and the optimal spectral preprocessing combination was second derivative with second smoothing. The optimal regression model was obtained with an R² of 0.8954 and an RMSECV of 0.06651 in the calibration set and R of 0.9614 and RMSEV of 0.04573 in the prediction set. These measurements reveal the calibration model had qualified predictive accuracy. The results demonstrated that the 2DCOS with PLS was a simple and rapid method for the quantitative determination of polyphenols in oats.     

多模型共识偏最小二乘法用于近红外光谱定量分析

将多模型共识偏最小二乘法用于近红外光谱定量分析。利用随机抽取的训练子集建立一系列偏最小二乘模型,选取其中性能较好的部分模型作为成员模型,用这些成员模型来预测未知样品。将该方法用于一组生物样本的近红外光谱与样品中人血清白蛋白、γ-球蛋白以及葡萄糖含量之间的建模研究,并与单模型偏最小二乘法了进行比较。结果 PLS对独立测试集中三种组分进行50次重复预测的平均RMSEP分别为0.1066,0.0853和0.1338,RMSEP的标准偏差分别为0.0174,0.0144和0.0416;而本方法重复预测的平均RMSEP分别为0.0715,0.0750和0.0781,RMSEP的标准偏差分别为0.0033,0.2729×10-4和0.0025。     

Components Analysis of Biochar Based on Near Infrared Spectroscopy Technology

This study aims to establish a rapid quantitative analysis method for biochar based on near infrared spectroscopy (NIRS) technology. Near infrared spectra of 163 samples in the 10000–3800 cm^–1 (1000–2632 nm) range were collected, and the contents of fixed carbon (FC), volatile matter (VM) and ash of samples were also analyzed. A partial least square (PLS) model for FC, VM and Ash was established after the model spectral ranges were optimized, the optimal factors were determined, and the raw spectra were pretreated by multiple scatter correction and second derivative (MSC + SD) method. Finally, the prediction performance of predictive model was evaluated. The results showed that the PLS model had a good prediction ability, and the predicted coefficient R²_p of actual values vs prediction values for FC, VM and ash were 0.9423, 0.9517 and 0.9265, respectively. Root mean square error of prediction (RMSEP) was 0.1074, 0.1201 and 0.1243, and ratios of prediction to deviation (RPD) were 3.51, 4.28 and 2.03, respectively. The PLS model had good accuracy and precision for both of FC and VM, and could be used as a quantitative method for FC and VM contents analysis. Nevertheless, PLS model need to improve the precision for Ash analysis according to RPD value. This method provides a fast and effective technical means for the quantitative analysis of biochar components.     

Quantitative Analysis of Catalpol in Chinese Patent Medicine Lixin Pill by Near-infrared Diffuse Reflectance Spectroscopy

Lixin pill is a typical Chinese patent medicine with anti-rheumatic heart disease activity that has been widely used in clinical practice. Therefore it is very important to detect the concentration of catalpol, as the main component of the active ingredient. Near-infrared reflectance（NIR） spectroscopy was used to study the content of catalpol in the unprocessed Chinese patent medicine of Lixin pills. NIR is applied to quantitatively analyze 77 sam- ples, which were randomly divided into a calibration set containing 61 samples and a prediction set containing 16 samples. To get a satisfying result, partial least squares（PLS） regression was utilized to establish quantitative models. In PLS regression, the values of coefficient of determination（R2） and root mean square error of cross-validation （RMSECV） of PLS regression are 0.9419 and 0.0216, respectively. The process of establishing model, parameters of model, and prediction results were also discussed in detail（root mean square error of prediction is 0.0164）. The over- all results show that NIR spectroscopy can be efficiently utilized for the rapid and accurate analysis of routine chemical compositions in the Chinese patent medicine of Lixin pills. The prediction set suggests that this quantitative analysis model has excellent generalization ability and prediction precision. Accordingly, the result can provide tech- nical support for the further analysis of catalpol in unprocessed Lixin pill. Moreover, this study supplied technical support for the further analysis of other Chinese patent medicine samples.     

Classification and determination of total protein in milk powder using near infrared reflectance spectrometry and the successive projections algorithm for variable selection

This paper proposes a methodology for the classification and determination of total protein in milk powder using near infrared reflectance spectrometry (NIRS) and variable selection. Two brands of milk powder were acquired from three Brazilian cities (Natal-RN, Salvador-BA and Rio de Janeiro-RJ). The protein content of 38 samples was determined by the Kjeldahl method and NIRS analysis. Principal component regression (PCR) and partial least squares (PLS) multivariate calibrations were used to predict the total protein. Soft independent modeling of class analogy (SIMCA) was also used for full-spectrum classification, resulting in almost 100% classification accuracy, regardless of the significance level adopted for the F-test. Using this strategy, it was feasible to classify powder milk rapidly and nondestructively without the need for various analytical determinations. Concerning the multivariate calibration models, the results show that PCR, PLS and MLR-SPA models are good for predicting total protein in powder milk; the respective root mean square errors of prediction (RMSEP) were 0.28 (PCR), 0.25 (PLS), 0.11 wt% (MLR-SPA) with an average sample protein content of 8.1 wt%. The results obtained in this investigation suggest that the proposed methodology is a promising alternative for the determination of total protein in milk powder.     

Simultaneous determination of levodopa and carbidopa by synchronous fluorescence spectrometry using double scans

The aim of this study was to investigate the potential use of a direct headspace-mass spectrometry electronic nose instrument (MS e_nose) combined with chemometrics as rapid, objective and low cost technique to measure aroma properties in Australian Riesling wines. Commercial bottled Riesling wines were analyzed using a MS e_nose instrument and by a sensory panel. The MS e_nose data generated were analyzed using principal components analysis (PCA) and partial least squares (PLS1) regression using full cross validation (leave one out method). Calibration models between MS e_nose data and aroma properties were developed using partial least squares (PLS1) regression, yielding coefficients of correlation in calibration (R) and root mean square error of cross validation of 0.75 (RMSECV: 0.85) for estery, 0.89 (RMSECV: 0.94) for perfume floral, 0.82 (RMSECV: 0.62) for lemon, 0.82 (RMSECV: 0.32) for stewed apple, 0.67 (RMSECV: 0.99) for passion fruit and 0.90 (RMSECV: 0.86) for honey, respectively. The relative benefits of using MS e_nose will provide capability for rapid screening of wines before sensory analysis. However, the basic deficiency of this technique is lack of possible identification and quantitative determination of individual compounds responsible for the different aroma notes in the wine.     

Development of Near-Infrared Reflectance Spectroscopy Models for Quantitative Determination of Water-Soluble Carbohydrate Content in Wheat Stem and Glume

Water-soluble carbohydrate (WSC) reserved in stem is an important agronomic trait for crop improvement. The intact samples and pieces of chipped samples were employed to determine WSC content by near-infrared reflectance spectroscopy (NIRS). Three NIRS models were developed to predict WSC content in wheat stem lower internode, upmost internode, and wheat glume, respectively. Moreover, a mixed model was developed for WSC quantitative analysis in the mixed sample of the three wheat organs. Statistics analysis indicated that the four models showed a high determination coefficient (R² ≥ 0.97) and ratio of standard deviation to RMSECV (RPD ≥ 5.99). The NIRS models would allow rapid and high throughout assessments and selections of WSC contents in wheat genetics and breeding programs.     

应用遗传算法和PLS的近红外光谱预测玉米中淀粉含量的研究

以普通玉米籽粒为试验材料,在应用遗传算法结合偏最小二乘回归法对近红外光谱数据进行特征波长选择的基础上,应用偏最小二乘回归法建立了特征波长测定玉米籽粒中淀粉含量的校正模型．试验结果表明,基于11个特征波长所建立的校正模型,其校正误差（RMSEC）、交叉检验误差（RMSECV）和预测误差（RMSEP）分别为0.30％、0.35％和0.27％,校正数据集和独立的检验数据集的预测值与实际测定值之间的相关系数分别达到0.9279和0.9390,与全光谱数据所建立的预测模型相比,在预测精度上均有所改善,表明应用遗传算法和PLS进行光谱特征选择,能获得更简单和更好的模型,为玉米籽粒中淀粉含量的近红外测定和红外光谱数据的处理提供了新的方法与途径．     

Feasibility study for the use of near infrared spectroscopy in the qualitative and quantitative analysis of green tea, Camellia sinensis (L.)

This paper indicates the possibility to use near infrared spectroscopy (NIR) combined with PLS as a rapid method to estimate the quality of green tea. NIR is used to build calibration models to predict the content of caffeine, epigallocatechin gallate (EGCG) and epicatechin (EC) and for the prediction of the total antioxidant capacity of green tea. For the determination of the total antioxidant capacity, the trolox equivalent antioxidant capacity (TEAC) method is used. Until now, the prediction of the antioxidant capacity as such by use of NIR has not been reported. For caffeine and TEAC, models are build for the whole green tea leaves and also for the ground leaves. For the polyphenols (EGCG and EC), only models for the whole leaves are investigated. A partial least squares (PLS) algorithm is used to perform the calibration. To decide upon the number of PLS factors included in the PLS model, the model with the lowest root mean square error of cross-validation (RMSECV) for the training set is chosen. The correlation coefficient (r) between the predicted and the reference results for the test set is used as an evaluation parameter for the models: for the TEAC results r=0.90 for the model with the whole leaves, r=0.86 for the model with the powdered leaves are obtained. The caffeine prediction model has a correlation coefficient r=0.96 for the whole leaves and r=0.93 for the ground leaves. The correlation coefficient for the EGCG and the EC content models are, respectively 0.83 and 0.44.     

Prediction of humic acid content and respiration activity of biogenic waste by means of Fourier transform infrared (FTIR) spectra and partial least squares regression (PLS-R) models

Fourier transform infrared (FTIR) spectroscopy has been proven to be an appropriate analytical method for the qualitative assessment of compost stability. This study focuses on quantitative determination of two time-consuming parameters: humic acid (HA) contents and respiration activity. Reactivity/stability and humification were quantified by respiration activities (oxygen uptake) and humic acid contents. These features are also reflected by a specific infrared spectroscopic pattern. Based on this relationship partial least squares regression (PLS-R) models for the prediction of respiration activities and humic acid contents were calculated. Characteristic wavenumber regions that are assigned to the biological/chemical parameter were selected for multivariate data analysis. The coefficient of determination (R²) obtained for the humic acid prediction model from infrared spectra was 87% with a root mean square error of cross-validation (RMSECV) of 2.6% organic dry matter (ODM). The prediction model for respiration activity resulted in a R² of 94% and a RMSECV for oxygen uptake of 2.9 mg g⁻¹ dry matter (DM).     

Simultaneous determination of total polyphenols and caffeine contents of green tea by near-infrared reflectance spectroscopy

This paper indicates the possibility to use near infrared (NIR) spectroscopy as a rapid method to predict quantitatively the content of caffeine and total polyphenols in green tea. A partial least squares (PLS) algorithm is used to perform the calibration. To decide upon the number of PLS factors included in the PLS model, the model is chosen according to the lowest root mean square error of cross-validation (RMSECV) in training. The correlation coefficient R between the NIR predicted and the reference results for the test set is used as an evaluation parameter for the models. The result showed that the correlation coefficients of the prediction models were R = 0.9688 for the caffeine and R = 0.9299 for total polyphenols. The study demonstrates that NIR spectroscopy technology with multivariate calibration analysis can be successfully applied as a rapid method to determine the valid ingredients of tea to control industrial processes.     

Evaluation of biodiesel-diesel blends quality using H NMR and chemometrics

In this work, the use of ¹H NMR spectroscopy and statistical approach to the evaluation of biodiesel-diesel blends quality is described. Forty-six mixtures of oil-diesel, biodiesel-diesel, and oil-biodiesel-diesel were analyzed by ¹H NMR and such data were employed to design four predictive models. Thirty-six mixtures were used in the calibration set and the others in the validation. The PCR and PLS models were evaluated through statistical parameters.Briefly, PLS and PCR models were suitable for the prediction of biodiesel and oil concentration in mineral diesel. Specially, in higher concentration the predicted values were quite similar to the real ones. This fact was evidenced by the low relative errors of high concentrated samples; this means that the prediction of low concentrated samples will probably show high deviation. Therefore, ¹H NMR-PLS and ¹H NMR-PCR methods are fairly useful for the quality control of biodiesel-diesel blends, particularly they are suitable for prediction of concentrations greater than 2%.     

A comparative study of diesel analysis by FTIR, FTNIR and FT-Raman spectroscopy using PLS and artificial neural network analysis

Diesel properties determined by ASTM reference methods as cetane index, density, viscosity, distillation temperatures at 50% (T50) and 85% (T85) recovery, and the total sulfur content (%, w/w) were modeled by FTIR-ATR, FTNIR, and FT-Raman spectroscopy using partial last square regression (PLS) and artificial neural network (ANN) spectral analysis. In the PLS models, 45 diesel samples were used in the training group and the other 45 samples were used in the validation. In the ANN analysis a modular feedforward network was used. Sixty diesel samples were used in the neural network training and other 30 samples were used in the validation. Two different ATR configurations were compared in the FTIR, a conventional (ATR1) and an immersion (ATR2) cell. The ATR1 cell presented the best results, with smaller prediction errors (root mean square error of prediction, RMSEP). The comparison of the three PLS models (FTIR-ATR1, FTNIR, and FT-Raman) shows that reasonable values of R² and RMSEP were obtained by the FTIR-ATR1 and FTNIR models in the evaluation of density, viscosity, and T50. The PLS/FT-Raman models presented reasonable results only for the T50 property. None of the techniques was able to generate suitable PLS calibration models for the determination of sulfur content. The ANN/FT-Raman models presented the best performances, with all models presenting R²-values above 85% some of them with RMSEP values significantly smaller than those obtained with FTIR-ATR and FTNIR. The ANN/FT-Raman and ANN/FTIR-ATR1 models were able to estimate the total sulfur content of diesel with 0.01% (w/w) accuracy.     

Improving the sensitivity of NIR spectroscopy with an enrichment technique: determining a trace analyte of ethyl carbamate.

An exploration was made to develop a determination method of a low-concentration analyte by NIR spectroscopy. An absorber, silica gel was employed to extract and enrich a low-concentration analyte of ethyl carbamate. The solid absorber with the enriched analyte was measured by NIR spectroscopy in the range of 800 - 2500 nm. Afterwards, PLS regression was performed between the NIR spectra and the concentrations of the analyte for quantitative analysis of the low-concentration analyte. The spectra of 20 solid samples of analyte-absorbed silica gel showed a good correlation with the concentrations of ethyl carbamate in the samples. A leave-one-out cross validation was applied to evaluate the prediction ability of PLS models built with the full spectra, spectra in the region of 1920 - 1970 nm and the region of 2250 - 2430 nm, respectively. The values of the root-mean-square error of the cross validation (RMSECV) were about 0.1 mg L(-1) (0.1 ppm).     

Simultaneous Determination of Quercetin and Luteolin in Dried Flowers by Multivariate HPLC-ECD Calibration

Two calibration models, partial least squares (PLS) and principal component regression (PCR), were applied to the simultaneous determination of quercetin and luteolin by high performance liquid chromatography (HPLC) with electrochemical detection (ECD). The proposed methods were successfully applied to the analysis of dried flower samples. It was found that the relative standard errors of prediction (RSEP) for the validation set of PLS of quercetin and luteolin was 1.31 and 2.23%, and the RSEP of PCR was found to be 3.56 and 4.32%, respectively. Several dried flower samples were analysed and the recoveries were in the range of 95.9–103.3%.     

Measurement of lactate in whole human blood with near-infrared transmission spectroscopy

We have evaluated the potential of near-infrared spectroscopy (NIRS) as a technique for rapid analysis of lactate in whole blood. To test the NIRS technique, a comparison was made with a standard clinical method using whole blood samples taken from five exercising human subjects at three different stage of exercise. To expand lactate concentration within the physiological range, standard additions method was used to generate 45 unique data points. Spectra were collected over the 2050-2400 nm spectral range with a 1 mm optical path length quartz cell. Reference lactate concentrations in the samples were determined by enzymatic measurements. Estimates and calibration of the lactate concentration with NIRS was made using partial least squares (PLS) regression analysis and leave-N-out cross validation on second derivative spectra. Separate calibrations were determined from each of the subject samples and cumulative PRESS was used to determine the number of PLS factors in the final model. The results from the PLS model presented are generated from the five individual calibration coefficient vectors and provided a correlation coefficient of 0.978 and a standard error of cross validation of 0.65 mmol l⁻¹ between the enzymatic assay and the NIRS technique. To study the parameters that impact the spectra baseline and the correlation between the calculated model and the data, referenced measurements of lactate against baseline spectrum were made for each individual. A correlation coefficient of 0.992 and a standard error of cross validation of 0.21 mmol l⁻¹ were found. The results suggest that NIRS may provide a valuable tool to assess physiological status for both research and clinical needs.     

Quantitative determination of Malathion in pesticide by modified attenuated total reflectance-Fourier transform infrared spectrometry applying genetic algorithm wavelength selection method

A simple and environment friendly method was developed for determination of Malathion content of analytical and commercial insecticide samples with no special preparation. Attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectra were characterized and 1000-2000 cm⁻¹ region was selected for quantitative analysis utilizing partial least square (PLS) and two wavelength selection methods: (a) principal component regression (PCR) and (b) genetic algorithm (GA). Relative error of prediction (REP) was calculated in PLS, PCR-PLS and GA-PLS methods and was 3.536, 1.656 and 0.188, respectively. Proposed method is successfully applicable for quantification of Malathion in commercial grade samples and reliable results in comparison with known methods, confirms this idea.