Visible light active hydrogen modified (HM)-n-TiO2 thin films for photoelectrochemical splitting of water

Visible light active hydrogen modified n-type titanium oxide (HM-n-TiO₂) thin films were synthesized by thermal oxidation of Ti metal sheet (Alfa Co. 0.25 mm thick) in an electric oven followed by incorporation of hydrogen electrochemically under cathodic polarization at ?1.6 V vs Pt. The photoresponse of the HM-n-TiO₂ was evaluated by measuring the rate of water splitting reaction to hydrogen and oxygen in terms of photocurrent density, J_p. The optimized electric oven-made n-TiO₂ and HM-n-TiO₂ photoelectrodes showed photocurrent densities of 0.2 mA cm^?2 and 1.60 mA cm^?2, respectively, at a measured potential of ?0.4 V vs Pt at illumination intensity of 100 mW cm^?2 from a 150 W xenon lamp. This indicated an eightfold increase in photocurrent density for HM-n-TiO₂ compared to oven-made n-TiO₂ at the same measured electrode potential. The band-gap energy of HM-n-TiO₂ was found to be 2.7 eV compared to 2.82 eV for electric oven-made n-TiO₂ and a mid-gap band at 1.67 eV above the valence band was also observed. The HM-n-TiO₂ thin film photoelectrodes were characterized using photocurrent density under monochromatic light illumination and UV–Vis spectral measurements.     

Chemical bias of electrochemical and photoelectrochemical water splitting using a hydrogel separator

Resorcinol-formaldehyde hydrogels are shown to be adequate separators in electrochemical and photoelectrochemical water splitting cells. Combined with concentrated buffer electrolytes, they allow the maintenance of relatively stable pH gradients between basic anolytes and acidic catholytes. The water splitting potential at a current density of 3.0 mA/cm² applied between two Pt electrodes and a pH bias of 8.1 units retained a value of 2.7 V for several hours. Using iron foam/hematite as photoanode and Pt as cathode, the water splitting photocurrents at an applied potential of 1.23 V reached values of 0.40 and 0.06 mA/cm² in the presence and absence, respectively, of this chemical bias.     

Anodic stripping voltammetric analysis of trace arsenic(III) enhanced by mild hydrogen-evolution at a bimetallic Au–Pt nanoparticle modified glassy carbon electrode

A glassy carbon electrode (GCE) modified with electrodeposited bimetallic Au–Pt nanoparticles (Au–PtNPs) was applied to sensitively detect As(III) by linear sweep anodic stripping voltammetry (LSASV). In 0.5 M aqueous H₂SO₄, atomic hydrogen and molecular hydrogen were easily electrogenerated at the Pt sites on Au–PtNPs/GCE, which can chemically reduce As(III) to As(0) and enhance the cathodic preconcentration of As(0) at both the Pt sites and the neighboring Au sites. Since the As(0)–Au affinity is weaker than the As(0)–Pt affinity, the preconcentrated As(0) can be rapidly oxidized on/near the surface Au sites of Au–PtNPs/GCE, yielding sharper and higher LSASV current peaks. Under optimum conditions (700 s preconcentration at − 0.1 V, 5 V s^− 1), the LSASV peak current for the As(0)–As(III) oxidation responded linearly to As(III) concentration from 0.005 to 3.0 μM with a limit of detection (LOD) of 3.7 nM (0.28 ppb) (S/N = 3), while that for the As(III)–As(V) oxidation was linear with As(III) concentration from 0.01 to 3.0 μM with a LOD of 6.0 nM (0.45 ppb) (S/N = 3). This method was applied for analysis of As(III) in real water samples.     

The electrochemical reduction of carbon dioxide (CO2) to methanol in the presence of pyridoxine (vitamin B6)

Experiments aimed at ameliorating carbon dioxide (CO₂) into methanol were explored using pyridoxine, a member of the vitamin B₆ family, to enhance the reduction process. At a platinum electrode, an aqueous solution (pH ≈ 5) of pyridoxine showed a quasi-reversible redox couple with the cathodic peak detected at ca. − 0.55 V vs. Ag/AgCl (3 M KCl) in the presence of CO₂ and argon. An increase in the corresponding cathodic peak current was observed following saturation of the solution with CO₂ using a Pt electrode, but with no detectable reduction current recorded at a glassy carbon electrode for the same system. Confirmation of methanol formation during the pyridoxine-assisted CO₂ reduction was conducted by using gas chromatography analysis of the electrolyzed solutions and faradic yields of ca. 5% were afforded. A combination of the results from the cyclic voltammetry and constant current chronopotentiometry experiments revealed an overpotential of ≤ 200 mV was required. The results indicate a potential utility of pyridoxine as an alternative reagent to the more toxic pyridine during the electrochemical reduction of CO₂.     

Si-doped Fe2O3 nanotubular/nanoporous layers for enhanced photoelectrochemical water splitting

The present work reports the enhancement of the photoelectrochemical water splitting performance of in-situ silicon (Si)-doped nanotubular/nanoporous (NT/NP) layers. These layers were grown by self-organizing anodization on Fe-Si alloys of various Si content. The incorporation of Si is found to retard the layer growth rates, leads to a more pronounced nanotubular morphology, and most importantly, an improved photoelectrochemical behavior. By increasing Si content from 1, 2 to 5 at.% in the iron oxide NT/NP photoanodes, the photocurrent onset potential shifts favorably to lower values. At 1.3 V vs. RHE, hematite layer with 5 at.% Si shows a 5-fold increase of the photocurrent, i.e. 0.5 mA cm^− 2 in comparison to 0.1 mA cm^− 2 for the undoped samples. The study also reveals that a suitable layer thickness is essential to achieve a beneficial effect of the Si doping.     

O2 surface concentration change and its implication on oxygen reduction mechanism and kinetics at platinum in acidic media

O₂ concentration near Pt surface during oxygen reduction reaction (ORR) in 0.1 M HClO₄ has been monitored by rotating ring-disk electrodes system. At 0.8 V < E < 1.0 V (vs. RHE), O₂ concentration near Pt surface increases with potential accompanying with the decrease of ORR current at the disk electrode; O₂ concentration in the negative-going scan is larger than that at the same potential in the positive-going scan, while ORR current shows the opposite trend at ω > 400 rpm. At E > 0.8 V accumulation of O_ad|OH_ad at Pt disk electrode with ORR time is evident, revealing that O_ad|OH_ad formation rate is faster than that for the removal of OH_ad to H₂O under such conditions. At relatively lower rotation speed and faster scan rate, the cathodic current during ORR in the negative-going scan can be larger than that in the positive-going scan with a current peak at ca. 0.8 V, which is attributed to the superimposition of ORR current increase due to change of O₂ concentration near the surface and the additional reduction of O_ad|OH_ad formed from decomposed O₂ at higher potentials.     

Platinum nanoparticles supported on nitrobenzene-functionalised graphene nanosheets as electrocatalysts for oxygen reduction reaction in alkaline media

A systematic study on the electrocatalytic properties of Pt nanoparticles supported on nitrobenzene-modified graphene (Pt-NB/G) as catalyst for oxygen reduction reaction (ORR) in alkaline solution was performed. Graphene nanosheets were spontaneously grafted with nitrophenyl groups using 4-nitrobenzenediazonium salt. The electrocatalytic activity towards the ORR and stability of the prepared catalysts in 0.1 M KOH solution have been studied and compared with that of the commercial Pt/C catalyst. The results obtained show that the NB-modified graphene nanosheets can be good Pt catalyst support with high stability and excellent electrocatalytic properties. The specific activity of Pt-NB/G for O₂ reduction was 0.184 mA cm⁻², which is very close to that obtained for commercial 20 wt% Pt/C catalyst (0.214 mA cm⁻²) at 0.9 V vs. RHE. The Pt-NB/G hybrid material promotes a four-electron reduction of oxygen and can be used as a promising cathode catalyst in alkaline fuel cells.     

CO tolerant Pt/WC methanol electro-oxidation catalyst

Platinum supported on WC (Pt/WC) catalyst (20 wt.% Pt) was synthesized as a new methanol electro-oxidation catalyst. Particle size of 7.5 nm was obtained from X-ray diffraction results and a uniform distribution of particles was observed by transmission electron microscopy. In cyclic voltammetry (CV) measurement, the reduction peak potential of PtO increased from 0.72 V in commercial Pt/C to 0.76 V in Pt/WC. By combining the CV and CO stripping results, spill-over of H⁺ from Pt to WC was observed. Electrochemically active surface area calculated from the desorption area of H⁺ were 11.2 and 5.74 m²/g catalyst for Pt/WC and Pt/C, while those obtained from the desorption area of CO were 4.42 and 6.40 m²/g catalyst, respectively. CO electro-oxidation peak potential greatly decreased from 0.80 V in Pt/C to 0.68 V in Pt/WC. The reaction of WC with water to produce WC–OH could lower to CO electro-oxidation peak potential. Specific activity for methanol electro-oxidation increased from 144 mA/m² in Pt/C to 188 mA/m² in Pt/WC.     

Oxygen reduction reaction activities of Ni/Pt(111) model catalysts fabricated by molecular beam epitaxy

Oxygen reduction reaction (ORR) activities were evaluated for clean Pt(111) and Ni/Pt(111) model catalysts fabricated by molecular beam epitaxy. Exposure of clean Pt(111) to 1.0 L CO at 303 K produced linear-bonded and bridge-bonded CO-Pt IR bands at 2093 and 1858 cm^? 1. In contrast, 0.3-nm-thick Ni deposited on Pt(111) at 573 K (573 K-Ni_0.3 nm/Pt(111)) produced broad IR bands for adsorbed CO at around 2070 cm^? 1; the separation of reflection high-energy electron diffraction (RHEED) streaks is slightly wider for 573 K-Ni_0.3 nm/Pt(111) than for the clean Pt(111). For 823 K-Ni_0.3 nm/Pt(111), the separation of the RHEED streaks is the same as that for the Pt(111), and a single sharp IR band due to adsorbed CO is located at 2082 cm^? 1. The results suggest that for the 823 K-Ni_0.3 nm/Pt(111), a Pt-enriched outermost surface (Pt-skin) was formed through surface segregation of the substrate Pt atoms. ORR activities for the 573 K- and 823 K-Ni_0.3 nm/Pt(111) as determined from linear sweep voltammetry curves were five times and eight times higher than that for clean Pt(111), respectively, demonstrating that Pt-skin generation is crucial for developing highly active electrode catalysts for fuel cells.     

Atomic force microscopy of cubic Pt nanoparticles in electrochemical environments

Real structure of cubic Pt nanoparticle has been studied at various potentials in 0.1 M NaClO₄ with the use of atomic force microscopy (AFM). Cubic Pt nanoparticles in 10 nm height are clearly imaged from 0.10 V to 1.10 V (Ag/AgCl). The height of the nanoparticle increases 1.2 ± 0.7 nm (10.4 ± 6.8%) around the onset potential of oxygen evolution (1.20 V (Ag/AgCl)). The height increase is attributed to the formation of the oxide species at the inner layers of the nanoparticle. Dissolution of the nanoparticle starts from the upper terrace, not from the edge above 1.40 V (Ag/AgCl).     

Activity of Pt anode catalyst modified by underpotential deposited Pb in a direct formic acid fuel cell

We characterized the electrocatalytic activity of platinum electrode modified by underpotential deposited lead (PtPb_upd) for a formic acid (HCOOH) oxidation and investigated the influence on the power performance of direct formic acid fuel cells (DFAFC). Based on the electrochemical analysis using cyclic voltammetry and chronoamperometry, PtPb_upd electrode modified by underpotential deposition (UPD) exhibited significantly enhanced catalytic activity for HCOOH oxidation below anodic overpotential of 0.4 V (vs. SCE). Multi-layered PtPb_upd electrode structure of Pt/Pb_upd/Pt resulted in more stable and enhanced performance using 50% reduced loading of anode catalyst. The performance of multi-layered PtPb_upd anode is about 120 mW/cm² at 0.4 V and it also showed a sustainable cell activity of 0.52 V at an application of constant current loading of 110 mA/cm².     

Adsorption of hydrogen on Pt(1 1 1) and Pt(1 0 0) surfaces and its role in the HOR

Hydrogen adsorption isotherms, evaluated by combination of cyclic voltammetry and chronoamperometry, are reported on Pt(1 1 1) and Pt(1 0 0) surfaces in 0.1 M HClO₄. We found that at E > 0.05 V Pt(1 1 1) and Pt(1 0 0) are only partially covered by the adsorbed hydrogen (H_ad). On both surfaces, a full monolayer of the adsorbed hydrogen is completed at −0.1 V, i.e. the adsorption of atomic hydrogen is observed in the hydrogen evolution potential region. We also found, that the activity of the hydrogen oxidation reaction is mirrored by the shape of the hydrogen adsorption isotherms, implying that H_ad is in fact a spectator in the HOR.     

A topographic view of the Pt(1 1 1) surface at the electrochemical interface in the presence of carbon monoxide

In this communication we present topographic images of the Pt(1 1 1) surface in CO saturated 0.1 M HClO₄, obtained by scanning tunneling microscopy.The topography presents two different structures, depending on the CO adsorption potential (E_ad = 0.15 V or E_ad = 0.5 V vs RHE). For adsorption at 0.15 V the system presents a heterogeneous appearance, which totally covers the surface and impedes the observation of steps on the substrate surface. When CO is adsorbed at 0.5 V large clusters forming chains along the steps are observed. These aggregates can be, tentatively, correlated with the H-bonded water structure suggested earlier on the basis of FTIR spectroscopy. The clusters have inhibitory effects on CO oxidation.     

Oxygen reduction reaction on the low index planes of palladium electrodes modified with a monolayer of platinum film

Oxygen reduction reaction (ORR) has been studied on the low index planes of Pd modified with a monolayer of Pt (Pt/Pd(hkl)) in 0.1 M HClO₄ with the use of hanging meniscus rotating disk electrode. The activity for ORR on bare Pd(hkl) electrode depends on the surface structure strongly, however, voltammograms of ORR on Pt/Pd(hkl) electrodes do not depend on the crystal orientation. The specific activities of Pt/Pd(hkl) electrodes at 0.90 V (RHE) are higher than that on Pt(1 1 0) which has the highest activity for ORR in the low index planes of Pt. The mass activity on Pt/Pd(hkl) electrode is 7 times as high as a commercial Pt/C catalyst.     

Photocurrent generated on a carotenoid-sensitized TiO2 nanocrystalline mesoporous electrode

Photocurrent was observed upon monochromatic illumination of an ITO electrode coated with a TiO₂ nanocrystalline mesoporous membrane with carotenoid 8′-apo-β-caroten-8′-oic acid (ACOA) deposited as a sensitizer (illuminated area 0.25 cm²) and immersed in an aqueous 10 mM hydroquinone (H₂Q), 0.1 M NaH₂PO₄ solution (pH = 7.4) purged with argon, using a platinum flag counter electrode (area 3.3 cm²) and a SCE reference electrode. The carotenoid-sensitized short-circuit photocurrent reached 4.6 μA/cm² upon a 40 μW/cm² incident light beam at 426 nm, with an IPCE (%, incident monochromatic photon-to-photocurrent conversion efficiency) as high as 34%. The short-circuit photocurrent was stable during 1 h of continuous illumination with only a 10% decrease. An open-circuit voltage of 0.15 V was obtained (upon 426 nm, 40 μW/cm² illumination) which remained at a constant value for hours. The observed open-circuit voltage is close to the theoretical value (0.22 V) expected in such a system. The action spectrum resembled the absorption spectrum of ACOA bound on the TiO₂ membrane with a maximum near 426 nm. No decay of the ACOA on the TiO₂ surface was observed after 12 h, presumably because of rapid regeneration of ACOA from ACOA⁺ at the surface by electron transfer from H₂Q.     

Ultra-low platinum loading high-performance PEMFCs using buckypaper-supported electrodes

The microstructure of the catalyst layer in proton exchange membrane fuel cells (PEMFCs) greatly influences catalyst (Pt) utilization and cell performance. We demonstrated a functionally graded catalyst layer based on a double-layered carbon nanotube/nanofiber film- (buckypaper) supported Pt composite catalyst to approach an idealized microstructure. The gradient distribution of Pt, electrolyte and porosity along the thickness effectively depresses the transport resistance of proton and gas. A rated power of 0.88 W/cm² at 0.65 V was achieved at 80 °C with a low Pt loading of 0.11 mg/cm² resulting in a relatively high Pt utilization of 0.18g_Pt/kW. The accelerated degradation test of catalyst support showed a good durability of buckypaper support because of the high graphitization degree of carbon nanofibers.     

Permanent electrochemical promotion of C3H8 oxidation over thin sputtered Pt films

The effect of “permanent electrochemical promotion of catalysis” (P-EPOC) was studied for the first time in the catalytic deep oxidation of C₃H₈ over a thin (～ 150 nm) sputtered Pt film on YSZ, under excess of oxygen at 350 °C. Short positive potential application (+ 1 V) resulted in a 5.6-fold increase of the catalytic rate, where C₃H₈ conversion reached 33%, while the apparent Faradaic efficiency was ～ 330. After positive current interruption the catalytic rate remained in a highly active steady-state, determined by the total charge of the anodic polarization step. Restoration of the catalytic activity to the initial value occurred only by a similar negative potential imposition. This new stable steady-state after current interruption can be interpreted by storage of a non-reactive oxygen species upon anodic polarization at the proximity of the Pt/YSZ interface and subsequent enhanced migration of spillover O^δ? species from the electrolyte support to the Pt/gas interface under open-circuit conditions.     

Amperometric biosensors based on deposition of gold and platinum nanoparticles on polyvinylferrocene modified electrode for xanthine detection

In this study, new xanthine biosensors, XO/Au/PVF/Pt and XO/Pt/PVF/Pt, based on electroless deposition of gold(Au) and platinum(Pt) nanoparticles on polyvinylferrocene(PVF) coated Pt electrode for detection of xanthine were presented. The amperometric responses of the enzyme electrodes were measured at the constant potential, which was due to the electrooxidation of enzymatically produced H₂O₂. Compared with XO/PVF/Pt electrode, XO/Au/PVF/Pt and XO/Pt/PVF/Pt exhibited excellent electrocatalytic activity towards the oxidation of the analyte. Effect of Au and Pt nanoparticles was investigated by monitoring the response currents at the different deposition times and the different concentrations of KAuCl₄ and PtBr₂. Under the optimal conditions, the calibration curves of XO/Au/PVF/Pt and XO/Pt/PVF/Pt were obtained over the range of 2.5 × 10^?3 to 0.56 mM and 2.0 × 10^?3 to 0.66 mM, respectively. The detection limits were 7.5 × 10^?4 mM for XO/Au/PVF/Pt and 6.0 × 10^?4 mM for XO/Pt/PVF/Pt. The effects of interferents, the operational and the storage stabilities of the biosensors and the applicabilities of the proposed biosensors to the drug samples analysis were also evaluated.     

Pt supported on carbon nanofibers as electrocatalyst for low temperature polymer electrolyte membrane fuel cells

Carbon nanofibers synthesized via the thermo catalytic decomposition of methane were investigated for the first time as an electrocatalyst support in PEMFC cathodes. Their textural and physical properties make them a highly efficient catalyst support for cathodic oxygen reduction in low temperature PEMFC. Tests performed in MEAs showed that Pt supported on carbon nanofibers exhibited an enhancement of ca. 94% in power density at 0.600 V, in comparison with a commercial catalyst supported on conventional carbon black, Pt/Vulcan XC-72R.     

Small diameter TiO2 nanotubes with enhanced photoresponsivity

We report ultraviolet (UV) light detection of thin wall TiO₂ nanotubes (TNTs) with open diameter ~ 20 nm obtained by a two anodization procedure. This small diameter nanotubular geometry shows significant enhancement of the photoresponsivity and results in a large increase of photocurrent. The photocurrent is one order higher than that of classical nanotubes with diameter of 140 nm at − 1.0 V bias. We attribute this improvement to the modulation of hole carrier density as a result of field effects from the diameter-dependent population of the surface-trapped electrons. This finding demonstrates inherent size effects of internal gain in semiconductor nanotubes.