Selective determination of trichloroacetic acid using silver nanoparticle coated multi-walled carbon nanotubes

Silver nanoparticle coated multi-walled carbon nanotubes (Ag/MWCNT) were prepared and used to fabricate a modified electrode. The Ag/MWCNT composites were observed by a transmission electron microscope (TEM), and the electrochemical properties of the Ag/MWCNT composite modified glassy carbon electrode were characterized by electrochemical measurements. The results showed that these composites had a favorable catalytic ability for the reduction of trichloroacetic acid (TCAA). Square wave voltammetric (SWV) technique was applied to detect TCAA. Under optimum conditions, the voltammetric determination of TCAA was performed with a linear range of 5.0 × 10^? 6–1.2 × 10^? 4 mol L^? 1 and a detection limit of 1.9 × 10^? 6 mol L^? 1 (S/N = 3).     

Worm-like mesoporous carbon synthesized from metal–organic coordination polymers for supercapacitors

A green and efficient route has been employed to synthesize a worm-like mesoporous carbon with high specific surface area (2587 m² g^?1) and large pore volume (3.14 cm³ g^?1). Three electrochemical methods have been used to measure its electrochemical performance. Worm-like mesoporous carbon performs the high specific capacitance (344 F g^?1) at constant-current densities of 50 mA g^?1.     

Double-layer capacitance of waste coffee ground activated carbons in an organic electrolyte

Using ZnCl₂ activation we prepared a series of carbon electrodes from waste coffee grounds to study the effect of mesopores on double-layer capacitance in a tetraethyl ammonium tetrafluoroborate/acetonitrile electrolyte. The activated carbon with the largest mesopore volume achieved an energy density of 34 Wh kg^?1 at low current loads, and significantly retained an energy density of 16.5 Wh kg^?1 and specific capacitance of more than 100 F g^?1 at fast charge–discharge rates (20 A g^?1). The effect of mesopores on capacitance at fast charge–discharge rates is discussed.     

Development of a solid phase extraction method for the multielement determination of trace metals in natural waters including sea-water by FI-ICP-MS

An automated solid phase extraction method by flow analysis on-line inductively coupled plasma mass spectrometry (FI-ICP-MS) for the determination of cobalt, chromium, nickel, cadmium, manganese, zinc, copper and lead in sea-water and other natural waters is described. The system is based on retention of the analytes onto a minicolumn packed with a chelating resin, 1,5-bis (2-pyridyl)-3-sulphophenyl methylene thiocarbonohydrazide immobilized on aminopropyl-controlled pore glass, placed in the injection valve of a simple flow manifold. The effects of chemical and flow variables were investigated and selected as a compromise between sensitivity and sampling frequency. So, the sample solutions (adjusted to pH 8.0 ± 0.5) were passed through the column. After washing the column with water, the adsorbed metals were subsequently eluted into the plasma with 4% m/m nitric acid. Detection limits of the trace metals (180 s sample loading time at a sample flow rate of 0.7 mL min^? 1; sampling frequency 8.6 h^? 1) were 0.002 μg L^? 1 for Co, 0.057 μg L^? 1 for Cr, 0.117 μg L^? 1 for Ni, 0.004 μg L^? 1 for Cd, 0.210 μg L^? 1 for Mn, 0.260 μg L^? 1 for Zn, 0.030 μg L^? 1 for Cu and 0.020 μg L^? 1 for Pb, with enrichment factors between 2.2 and 6.8. The accuracy of the proposed method was checked with certified reference materials (CRMs) of sea-water SLEW 3, LGC6016 and CASS-5, river water SLRS-5 and fortified lake water TMDA-54.4. The results from the determination of these metals were in agreement with the certified values and recovery values ranged between 92.2 and 110.6%. The method was applied to the determination of these metal ions in sea-water samples collected in the Málaga Bay in order to realize a pilot study necessary to generate preliminary information on which to base a more detailed pollution study by heavy metals of the Bay.     

Column solid phase extraction and determination of ultra-trace Au,Pd and Pt in environmental and geological samples

A new sorbent based on cysteine modified silica gel (SiG-cys) was prepared and studied for preconcentration and separation of noble metals Au(III), Pd(II), Pt(II), Pt(IV). Its extraction efficiency was examined by batch and column solid phase extraction procedures. Laboratory experiments performed showed that sorbent is characterized with high selectivity, permiting quantitative sorption (93–97%) of noble metals Au, Pd and Pt from acidic media 0.1–2 mol L^? 1 HCl and unsignificant sorption (less than 2%) for common base metals like Cu, Fe, Mn and Zn. The analytes retained on the sorbent are effectively eluted with 0.1 mol L^? 1 thiourea in 0.1 mol L^? 1 HCl and measured by ETAAS or ICP OES under optimal instrumental parameters. The sorbent showed high mechanical and chemical stability and extraction efficiency was not changed after 500 cycles of sorption/desorption. The sorbent was successfully applied in analyticals procedures for preconcentration and determination of Au, Pd and Pt in geological and soil samples. Detection limits (3σ criteria) achieved, depending on the instrumental methods used are: ETAAS (0.005 μg L^? 1 for Au in river and sea water, 0.002 μg g^? 1 for Au in copper ore and copper concentrate); ICP OES (0.03 μg L^? 1 for Pd and 0.06 μg L^? 1 for Pt in river and sea water, 0.006 μg g^? 1 for Pd in copper ore and copper concentrate and 0.002 μg g^? 1 for soluble Pt in soil). The accuracy of the procedures developed was confirmed by added/found method for sea and river water; by the analysis of national certified materials (copper ore and copper concentrate for Au and Pd) and by determination of the sum of soluble Pt(II) + Pt(IV) in spiked soil samples.     

Assay of caffeoylquinic acids in Baccharis trimera by reversed-phase liquid chromatography

Baccharis trimera commonly named ‘carqueja’, is wide-spread in South America and are used as raw material for herbal medicines. A reversed-phase liquid chromatography (RP-LC) method coupled to diode array detector was developed for the analysis of caffeoylquinic acids (CQAs), the main compounds responsible for its digestive activity. The identity of the quinic acids was established by mass spectrometry and were them: 5-O-[E]-caffeoylquinic acid, 3,4-O-[E]-dicaffeoylquinic acid, 3,5-O-[E]-dicaffeoylquinic acid, 4,5-O-[E]-dicaffeoylquinic acid and a tricaffeoylquinic acid. The RP-LC method for the quantitation of the caffeoylquinic acids was validated according to ICH guidelines, based on the following parameters: linearity, selectivity, robustness, limits of detection and quantification, precision and recovery. Hydroalcoholic extracts were prepared by the maceration of the plant material with ethanol:water 1:1 (v/v) in a 0.1:25 g mL^?1 plant:solvent ratio in a water bath at 40 °C. Validation data indicated that the HPLC method proposed is suitable for the analysis of caffeoylquinic acids in B. trimera raw material. The results of the LOD and LOQ analyses for the 5-CQA were 4.1 μg mL^?1 and 12.5 μg mL^?1, respectively, 1.3 μg mL^?1, 3.9 μg mL^?1 for 4,5-diCQA and 1.7 μg mL^?1, 5.1 μg mL^?1 for triCQA. The levels of total CQAs ranged from 2.1 to 4.0 g% (w/w). The influence of season harvest and site collection was also evaluated and variations were observed in the results and can be related to phonologic phase, different locations, seasons and soil. Long term and photostability of plant material were carried out and was observed a stable behavior during the time of the experiments.     

Contribution enthalpic in the interaction of activated carbon with polar and apolar solvents

A method is presented for calculating the contribution that enthalpies make for every component of mixtures of activated carbon–water and activated carbon–hexane to the immersion enthalpy using the concepts that are used in the solution enthalpies. The immersion enthalpies of microporous activated carbon in water and in hexane have values from ?18.97 to ?27.21 and ?25.23 to ?47.89 J g^?1, respectively. From the immersion enthalpies and mass relation of the activated carbon in each of the solvents, the differential enthalpies are calculated for the activated carbon in water, Hw_DIFac, with values between ?15.95 and ?26.81 J g^?1, as are the differential enthalpies for the activated carbon in hexane, ΔHh_DIFac, with values between ?6.86 and ?46.97 J g^?1. For a low mass relation of the mixture components the contributions to the immersion enthalpy of the activated carbon and water differ by 3.20 J g^?1, while the difference between the contributions of the activated carbon and hexane is 19.41 J g^?1.     

An activated carbon with high capacitance from carbonization of a resorcinol–formaldehyde resin

A polymeric activated carbon (PAC) was synthesized from the carbonization of a resorcinol–formaldehyde resin with KOH served as an activation agent. The nitrogen adsorption–desorption at 77 K, X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the prepared PAC. Compared with the commercial activated carbon (Maxsorb: Kansai, Japan), PAC shows superior capacitive performance in terms of specific capacitance, power output and high energy density as electrode materials for supercapacitors. PAC presents a high specific capacitance of 500 F g^?1 in 6 mol l^?1 KOH electrolyte at a current density of 233 mA g^?1 which remained 302 F g^?1 even at a high current density of 4.6 A g^?1. The good electrochemical performance of the PAC was ascribed to well-developed micropores smaller than 1.5 nm, the presence of electrochemically oxygen functional groups and low equivalent series resistance.     

Low potential detection of nicotine at multiwalled carbon nanotube–alumina-coated silica nanocomposite

Electrocatalytic oxidation of nicotine at multiwalled carbon nanotube (MWCNT)–alumina-coated silica (ACS) nanocomposite modified glassy carbon electrode are described. The sensing performance of the MWCNT–ACS nanocomposite modified glassy carbon electrode for the electrooxidation of nicotine was investigated using cyclic voltammetry and amperometry in 0.1 M phosphate buffer solution (pH 8). The MWCNT–ACS nanocomposite modified glassy carbon electrode exhibited the abilities to decrease the electrooxidation potential, to prevent the electrode surface fouling, and to raise the current responses. The MWCNT–ACS nanocomposite responded rapidly to nicotine with a sensitivity of 1.786 A M^?1 cm^?2 and a detection limit of 1.42 μM (according to 3σ criterion). A signal almost 180 times more sensitive was obtained at MWCNT–ACS nanocomposite modified glassy carbon electrodes as compared to bare glassy carbon electrode. The nicotine oxidation potential obtained in this study is much lower than that at boron-doped diamond electrodes.     

Macroporous Co3O4 platelets with excellent rate capability as anodes for lithium ion batteries

This paper reports the microwave-assisted synthesis of Co₃O₄ nanomaterials with different morphologies including nanoparticles, rod-like nanoclusters and macroporous platelets. The new macroporous platelet-like Co₃O₄ morphology was found to be the best suitable for reversible lithium storage properties. It displayed superior cycling performances than nanoparticles and rod-like nanoclusters. More interestingly, excellent high rate capabilities (811 mAh g^?1 at 1780 mA g^?1 and 746 mAh g^?1 at 4450 mA g^?1) were observed for macroporous Co₃O₄ platelet. The good electrochemical performance could be attributed to the unique macroporous platelet structure of Co₃O₄ materials.     

The determination of trace lead in drinking water by flow injection spectrophotometry

Lead is the non-essential trace element in the human body, and it has been confirmed that drinking water is one of the sources of lead in human body. In the research, based on the sensitive colour reaction of lead with I^?–EV⁺–PVA, a simple, sensitive, accurate and portable method for the determination of trace lead in drinking waters was proposed. Chemicals and physicals had been optimized in detail. The apparent molar absorption coefficient was up to 7.4 × 10⁵ mol L^?1 cm^?1. The developed method provided a linearity range over 5–80 μg L^?1. The regression deviation was between 0.71% and 2.33%. The 3σ detection limit was 0.9 μg L^?1. Close to the quantitation limit for the analyte the relative standard deviation was 1.10% (n = 10) at 40 μg L^?1. The method developed here for analysis of lead yielded results that were comparable with those of the GFAAS.     

Copper(II)–neocuproine reagent for spectrophotometric determination of captopril in pure form and pharmaceutical formulations

A simple, rapid, sensitive and accurate spectrophotometric method for the determination of captopril in pure form and pharmaceutical formulations is developed. The procedure is based on the reaction of copper(II) with captopril in the presence of neocuproine (NC) (2,9-dimethyl-1,10-phenanthroline) reagent in acetate buffer at pH 5.0. Copper(II) is reduced easily by captopril to Cu(I)–neocuproine complex, which shows an absorption maximum at 448 nm. Beer’s law was obeyed in the concentration range 0.3–3.0 μg mL^?1 with a minimum detection limit (LOD) of 0.039 μg mL^?1 and a quantification limit (LOQ) of 0.129 μg mL^?1. For more accurate results, Ringbom optimum concentration ranges was 0.5–2.7 μg mL^?1. The apparent molar absorbtivity and Sandell sensitivity were calculated. The validity of the proposed method was tested by analyzing the pure and pharmaceutical formulations and compared well with those obtained by the official method and demonstrated good accuracy and precision.     

Novel luminescent nanoparticles for DNA detection

Highly luminescent LaF₃:Ce³⁺/Tb³⁺ nanocrystals were successfully prepared and surface functionalized via Layer-by-Layer technology. These as-prepared nanocrystals are highly resistant to photobleaching and pretty dispersible in aqueous solution. Due to the efficient luminescence quenching of the nanocrystals by nucleic acids, a facile fluorescence quenching method was developed for the detection of trace amount of nucleic acids. Under optimal conditions, the fluorescence intensity was proportional to the DNA concentration over the range of 0.60–25.0 μg mL^?1 for calf thymus DNA (ct-DNA) and 0.60–30.0 μg mL^?1 for herring sperm DNA (hs-DNA), respectively. The corresponding detection limit is 0.21 μg mL^?1 for ct-DNA and 0.31 μg mL^?1 for hs-DNA, respectively. The results indicated that the reported method is simple and rapid with wide linear range. Also, the recovery and relative standard deviation of this method are reasonable and satisfactory.     

Fibriform polyaniline/nano-TiO2 composite as an electrode material for aqueous redox supercapacitors

Fibriform polyaniline/nano-TiO₂ composite is prepared by one-step in situ oxidation polymerization of aniline in the presence of nano-TiO₂ particles, which contains 80% conducting polyaniline by mass, with a conductivity of 2.45 S/cm at 25 °C. Its maximum specific capacitance is 330 F g^?1 at a constant current density of 1.5 A g^?1, and can be subjected to charge/discharge over 10,000 cycles in the voltage range of 0.05–0.55 V.     

Fabrication of porous carbon/Si composite nanofibers as high-capacity battery electrodes

Carbon/Si composite nanofibers with porous structures are prepared by electrospinning and subsequent carbonization processes. It is found that these porous composite nanofibers can be used as anode materials for rechargeable lithium-ion batteries (LIBs) without adding any binding or conducting additive. The resultant anodes exhibit good electrochemical performance; for example, a large discharge capacity of 1100 mAh g^?1 at a high current density of 200 mA g^?1.     

Fabrication of porous Co/NiO core/shell nanowire arrays for electrochemical capacitor application

We report self-supported porous Co/NiO core/shell nanowire arrays via the combination of hydrogen reduction and chemical bath deposition methods. The Co nanowire acts as the backbone for the growth of NiO nanoflake shell forming hierarchically porous Co/NiO core/shell nanowire arrays. As electrode materials for pseudo-capacitors, the Co/NiO core/shell nanowire arrays exhibit a specific capacitance of 956 F g^− 1 at 2 Å g^− 1 and 737 F g^− 1 at 40 Å g^− 1, and good cycling stability, which is mainly due to the metal nanowire based core/shell nanowire architecture which provides good conductive network as well as fast ion/electron transfer and sufficient contact between active materials and electrolyte.     

Nano TiO2-based preconcentration for the speciation analysis of inorganic selenium by using ion chromatography with conductivity detection

A simple, sensitive, and cost-effective analytical method was developed for the speciation analysis of inorganic selenium by combining a nano-TiO₂ preconcentration with an ion chromatography-conductivity detection (IC-CD) system. The experimental conditions for the simultaneous adsorption and desorption of Se(IV) and Se(VI) were carefully investigated. Under the established optimum condition, the Se(IV) and Se(VI) ions could been simultaneously adsorbed onto the nano-TiO₂ surface at pH 4.0, and then effectively desorbed by 0.1 M sodium hydroxide eluent. The adsorption process was fast and reached adsorption equilibrium within 10 min. The nano-TiO₂ also exhibited high adsorption capacity with 11.3 mg g^? 1 for Se(IV) and 8.34 mg g^? 1 for Se(VI). The enrichment factors for Se(IV) and Se(VI) were calculated to be 39 and 30, respectively, with sample volume of 50 mL. The detection limits (3σ) were 0.8 μg L^? 1 for Se(IV) and 0.4 μg L^? 1 for Se(VI), which were sensitive enough for the routine analysis of water and drink samples. The relative standard deviation was calculated to be < 4% (n = 6) for detection of 30 μg L^? 1 Se(IV) and 30 μg L^? 1 Se(VI). The results of the present work confirmed that our developed nano-TiO₂-IC-CD method could be applied for the detection of inorganic selenium species in tap water and drink samples with good recoveries in the range of 82%–108%.     

A high-performance carbon derived from polyaniline for supercapacitors

Activated carbon derived from rod-shaped polyaniline (the diameter of 170 nm) was synthesized by carbonization and subsequent activation with KOH. The obtained activated carbon exhibits a high specific capacitance (455 F g^?1) and remarkable rate capability due to its high specific surface area (1976 m² g^?1), narrow pore size distribution (< 3 nm) as well as short diffusion length. It is indicated that the promising synthetic method used in this work can pave the way for designing new carbon based materials from different polymers for high-performance energy applications.     

Poly-xanthurenic acid as an efficient mediator for the electrocatalytic oxidation of NADH

This paper describes, for the first time, the development of a simple and highly sensitive chemical sensor based on a new electroactive material, electrogenerated in situ from xanthurenic acid on an electrode modified with MWCNT. The modified electrode shows efficient electrocatalytic oxidation activity towards NADH at an applied potential of 0.1 V vs. Ag/AgCl. The kinetic constant, k_kin, for the electrocatalytic oxidation of NADH, evaluated by chronoamperometry and voltammetry using RDE, provided values close to 10⁵ mol^?1 L s^?1.     

Improving the cycleability of Si anodes by covalently grafting with 4-carboxyphenyl groups

In this study, the lithium storage capacity of Si nanoparticles is significantly enhanced by grafting with 4-carboxyphenyl groups via diazonium salts. The modified Si anodes exhibit reversible capacities of 1173 and 527 mA h g^?1 at the 1st and 50th cycle, while those of the bare Si electrodes are only 56 and 62 mA h g^?1, respectively. The improved electrochemical performance is supposed to arise from the formation of a robust and flexible solid electrolyte interface on the surfaces of the modified Si nanoparticles.