In situ AFM studies of SEI formation at a Sn electrode

Early stages of the solid electrolyte interphase (SEI) formation at a tin foil electrode in an ethylene carbonate (EC) based electrolyte were investigated by in situ AFM and cyclic voltammetry (CV) at potentials >0.7 V, i.e., above the potential of Sn–Li alloying. We detected and observed initial steps of the surface film formation at ～2.8 V vs. Li/Li⁺ followed by gradual film morphology changes at potentials 0.7 < U < 2.5 V. The SEI layer undergoes continuous reformation during the following CV cycles between 0.7 and 2.5 V. The surface film on Sn does not effectively prevent the electrolyte reduction and a large fraction of the reaction products dissolve in the electrolyte. The unstable SEI layer on Sn in EC-based electrolytes may compromise the use of tin-based anodes in Li-ion battery systems unless the interfacial chemistry of the electrode and/or electrolyte is modified.     

Anti-biofouling properties of amphiphilic phosphorylcholine polymer films

Surfaces of amphiphilic phosphorylcholine polymer (PC1036) prepared by spin-coating were characterized by spectroscopic ellipsometry, water contact angle and atomic force microscopy. The antifouling properties of the PC1036 films to marine benthic diatom Nitzschia closterium MMDL533 were also investigated. The results showed that the dry PC1036 film promoted the adhesion of N. closterium MMDL533 because the hydrophobic lauryl groups were present in the film surface. The 2 h-swelled PC1036 films had excellent anti-fouling properties with extremely low attachment densities and retention densities no matter what the annealing temperature was. The thickness of the coated films lower than 147 Å had a profound effect on the film anti-fouling properties. Otherwise, when the film thickness was higher than that value, there was no more improvement of diatom cell reduction observed. The annealing temperature had only a little effect on the film resistant to diatom adhesion, which might be attributed to two factors including the PC group packing densities in the outer PC layer and the equilibrated water volume fraction in the 2 h-swelled PC1036 films.     

Polypyrrole/carbon supercapacitor electrode with remarkably enhanced high-temperature cycling stability by TiC nanoparticle inclusion

In the potential applications for electric vehicle and stand-alone renewable energy storage, supercapacitors are likely to constantly operate at elevate temperatures, and yet the study on high-temperature cycling behavior of conducting polymer-containing supercapactors is scarce. Polypyrrole (PPy) film, doped with p-toluenesulfonate, has been coated onto activated carbon (AC) electrode preform. Although the specific capacitance of the electrode is doubled, from 176 F/g to 352 F/g, with coating of 17.7 wt.% PPy, the capacitance lost nearly 60% after 10,000 cycles at 40 °C, in contrast to 20% loss at 25 °C. It is demonstrated that the problem of accelerated fading at high temperature is effectively alleviated, in conjunction with significant (up to 50%) improvement in power performance, by embedding conductive TiC nanoparticles within the PPy layer via co-electroplating. With addition of 1.7 wt.% of TiC in the composite electrode, the capacitance retains 92% of its initial capacitance under the same cycling condition (40 °C, 10,000 cycles). The enhanced high-temperature cycling stability has in part been attributed to the reduction in the mismatch of thermal expansion coefficient between the conducting polymer layer and the AC substrate.     

Potentiodynamic hydrogen permeation on Palladium-Kelvin probe compared to 3D printed microelectrochemical cell

A specially designed flow cell, fabricated via rapid prototyping (3D printing), was used to perform in-situ electrochemical hydrogen loading and cyclic voltammetry on a Pd foil in alkaline solution during scanning Kelvin probe (SKP) measurements. SKP was successfully employed for hydrogen detection on the exit side of the sample, including determination of hydrogen diffusion coefficient in Pd to 3.32 ⋅ 10^− 7 cm²⋅ s^− 1 at 23 °C. Convection of electrolyte allowed hydrogen charging even under H₂-forming conditions without surface blockage by evolving gas bubbles at very negative potentials. Comparison with electrochemical hydrogen detection under the same conditions, allowed a more comprehensive interpretation of SKP results including determination of trapping effects on measurement of diffusion coefficient. In this manner, the potentiodynamic hydrogen loading technique combined with SKP-H-detection was utilized to determine the effective hydrogen diffusion coefficient (D_eff).     

Active protective Al–Ce alloy coating electrodeposited from ionic liquid

The electrochemical co-deposition of Al–Ce metallic protective coating with active inhibiting effect was performed for the first time using an ionic liquid as an electrolyte. Cerium was successfully co-deposited with aluminium on surface of Pt and AA2024 aluminium alloy forming uniform films with globular micro-structure and thickness up to 75 μm.Cerium was introduced into the aluminium coating as a potential corrosion inhibitor which can be liberated during sacrificial dissolution of the galvanic layer deposited on the alloy surface. The released inhibitor provides an additional active corrosion protection slowing down the corrosion processes in the defects.     

Mesoporous silica thin films for molecular sieving and electrode surface protection against biofouling

Electrode fouling is a major challenge for the long term use of sensors in real samples as it leads to the decay of the electroanalytical signal and is often caused by the formation of an inhibiting layer formed by biomolecules. We demonstrate here that ordered and vertically aligned mesoporous silica generated at the surface of an indium tin oxide electrode by electrochemically assisted self-assembly act as a molecular sieve and a protective layer for the electrode surface. They indeed prevent the adsorption of size excluded large undesired molecules (e.g. haemoglobin) while allowing the detection of small redox active molecules likely to reach the electrode surface through the film (e.g. propranolol) with almost no loss of sensitivity. At a bare electrode, the oxidation of propranolol is completely inhibited in the presence of 5 μM haemoglobin. At a modified electrode, the sensitivity for propranolol in the absence of haemoglobin is (72.8 ± 2.9) mA mol^− 1 (R² = 0.992, N = 7) and it remains similar in the presence of 5 μM haemoglobin with a value of (67.4 ± 7.2) mA mol^− 1 (R² = 0.992, N = 7).     

Characterization of SEI layer formed on high performance Si–Cu anode in ionic liquid battery electrolyte

Formation of the SEI layer on Si–Cu film electrode in the ionic liquid electrolyte of 1 M lithium bis(trifluoromethylsulfonyl)imide/1-methyl-1-propylpyrrolidinium bis(trifluoromethylsulfonyl)imide (LiTFSI/MPP-TFSI) was investigated using ex-situ ATR FTIR and X-ray photoelectron spectroscopy. The SEI layer is found to be composed of organic and inorganic compounds that are the decomposition products of MPP cation and TFSI anion, and effectively passivate the electrode surface during initial cycling. Formation of a stable SEI layer leads to an excellent capacity retention 98% of the maximum discharge capacity, delivering discharge capacities of > 1620 mAhg^? 1 over 200 cycles. The data contribute to a basic understanding of SEI formation and composition responsible for the cycling performance of Si-based alloy anodes in ionic liquid electrolyte-based rechargeable lithium batteries.     

Synthesis of Au/C and Au/Pani for anode electrodes in glucose microfluidic fuel cell

Gold nanoparticles have been prepared by two methods: chemical (ex-situ, Au/C) by two phase protocol, and electrochemical (in-situ, Au/Pani) by electroreduction of gold ions on a polyaniline film and compared as anode catalysts in a glucose microfluidic fuel cell. In this paper the structural characteristics and electrocatalytic properties were investigated by X-ray diffraction and electrochemical measurements. The catalytic behavior of both anodes was tested in a microfluidic fuel cell with a reference electrode incorporated, by means of linear sweep voltammetry (LSV), showing a cathodic shift in the glucose oxidation peak for Au/Pani. Results show a higher power density (0.5 mW cm^? 2) for Au/C anode compared with an already reported value, where a glucose microfluidic fuel cell was used in similar conditions.     

Corrosion behaviour of an Mg–Y–RE alloy used in biomedical applications studied by electrochemical techniques

Magnesium, due to its biocompatibility, a necessity in metabolic processes, and better mechanical properties than polymer, is an ideal candidate for biodegradable implants. The main actual limitation for the use of magnesium alloys is its too fast degradation rate in the physiological environment. The corrosion behaviour of an Mg–Y–RE magnesium alloy in two different physiological solutions (artificial plasma (AP) and simulated body fluid (SBF)) was investigated, using electrochemical impedance spectroscopy (EIS).The investigation showed that SBF is significantly more aggressive than AP with regard to the polished surface. A large difference in the corrosion rate and mechanisms (uniform or localized corrosion) is observed as a function of the buffer capacity of the media, but also of the carbonate and chloride content. For temporary surface protection, the formation of an approximately 350–400 nm dense hydroxide layer is obtained by electrochemical anodising. An increase of the corrosion resistance of the treated alloy for both physiological solutions is obtained, and this is especially noticeable for a long immersion time in AP.     

Deoxyribonucleic acid modified poly(dimethylsiloxane) microfluidic channels for the enhancement of microchip electrophoresis

In this paper, deoxyribonucleic acid (DNA) was employed to construct a functional film on the PDMS microfluidic channel surface and apply to perform electrophoresis coupled with electrochemical detection. The functional film was formed by sequentially immobilizing chitosan and DNA to the PDMS microfluidic channel surface using the layer-by-layer assembly. The polysaccharide backbone of chitosan can be strongly adsorbed onto the hydrophobic PDMS surface through electrostatic interaction in the acidic media, meanwhile, chitosan contains one protonatable functional moiety resulting in a strong electrostatic interactions between the surface amine group of chitosan and the charged phosphate backbone of DNA at low pH, which generates a hydrophilic microchannel surface and reveals perfect resistance to nonspecific adsorption of analytes. Aminophenol isomers (p-, o-, and m-aminophenol) served as a separation model to evaluate the effect of the functional PDMS microfluidic chips. The results clearly showed that these analytes were efficiently separated within 60 s in a 3.7 cm long separation channel and successfully detected on the modified microchip coupled with in-channel amperometric detection mode at a single carbon fiber electrode. The theoretical plate numbers were 74,021, 92,658 and 60,552 N m^?1 at the separation voltage of 900 V with the detection limits of 1.6, 4.7 and 2.5 μM (S/N = 3) for p-, o-, and m-aminophenol, respectively. In addition, this report offered an effective means for preparing hydrophilic and biocompatible PDMS microchannel surface, which would facilitate the use of microfluidic devices for more widespread applications.     

Thick lanthanum zirconate buffer layers from water-based precursor solutions on Ni-5%W substrates

In this work, water-based precursor solutions suitable for dip-coating of thick La₂Zr₂O₇ (LZO) buffer layers for coated conductors on Ni-5%W substrates were developed. The solutions were prepared based on chelate chemistry using water as the main solvent. The effect of polymer addition on the maximum crack-free thickness of the deposited films was investigated. This novel solution preparation method revealed the possibility to grow single, crack-free layers with thicknesses ranging 100–280 nm with good crystallinity and an in-plane grain misalignment with average FWHM of 6.55°. TEM studies illustrated the presence of nanovoids, typical for CSD–LZO films annealed under Ar-5%H₂ gas flow. The appropriate buffer layer action of the film in preventing the Ni diffusion was studied using XPS. It was found that the Ni diffusion was restricted to the first 30 nm of a 140 nm thick film. The surface texture of the film was improved using a seed layer.     

Photoinduced magnetic properties of sequentially deposited thin films of RbjCok[Fe(CN)6]l · nH2O

Using sequential deposition methods, we have generated two different films of Rb_jCo_k[Fe(CN)₆]_l · nH₂O for magneto-optical studies. The synthesis protocol was intentionally varied in order to generate samples with different degrees of surface homogeneity. As a consequence, film 1 possessed a powder-like rough surface, while film 2 was a smooth, quasi-two-dimensional film. Upon irradiation at 5 K with an external magnetic field of 200 G perpendicular to the film surface, the magnetization of film 1 increased, whereas the magnetization of film 2 decreased. This contrasting behavior is consistent with a dipolar field model describing the phenomena and is related to the novel anisotropy of the photoinduced magnetism in film 2, where the photoinduced magnetization increases or decreases depending on the orientation of the film with respect to the external field.     

Experimental investigation on the dissociation conditions of methane hydrate in the presence of imidazolium-based ionic liquids

In this work, the performance of nine ionic liquids (ILs) as thermodynamic hydrate inhibitors is investigated. The dissociation temperature is determined for methane gas hydrates using a high pressure micro deferential scanning calorimeter between (3.6 and 11.2) MPa. All the aqueous IL solutions are studied at a mass fraction of 0.10. The performance of the two best ILs is further investigated at various concentrations. Electrical conductivity and pH of these aqueous IL solutions (0.10 mass fraction) are also measured. The enthalpy of gas hydrate dissociation is calculated by the Clausius–Clapeyron equation. It is found that the ILs shift the methane hydrate (liquid + vapour) equilibrium curve (HLVE) to lower temperature and higher pressure. Our results indicate 1-(2-hydroxyethyl) 3-methylimidazolium chloride is the best among the ILs studied as a thermodynamic hydrate inhibitor. A statistical analysis reveals there is a moderate correlation between electrical conductivity and the efficiency of the IL as a gas hydrate inhibitor. The average enthalpies of methane hydrate dissociation in the presence of these ILs are found to be in the range of (57.0 to 59.1) kJ ⋅ mol⁻¹. There is no significant difference between the dissociation enthalpy of methane hydrate either in the presence or in absence of ILs.     

Amperometric glucose sensor based on glucose oxidase immobilized on gelatin-multiwalled carbon nanotube modified glassy carbon electrode

We investigated the direct electrochemistry of glucose oxidase (GOx) at gelatin-multiwalled carbon nanotube (GCNT) modified glassy carbon electrode (GCE). GOx was covalently immobilized onto GCNT modified GCE through the well known glutaraldehyde (GAD) chemistry. The immobilized GOx showed a pair of well-defined reversible redox peaks with a formal potential (E⁰′) of ? 0.40 V and a peak to peak separation (ΔE_p) of 47 mV. The surface coverage concentration (Г) of GOx in GCNT/GOx/GAD composite film modified GCE was 3.88 × 10^? 9 mol cm^? 2 which indicates the high enzyme loading. The electron transfer rate constant (k_s) of GOx immobilized onto GCNT was 1.08 s^? 1 which validates a rapid electron transfer processes. The composite film shows linear response towards 6.30 to 20.09 mM glucose. We observed a good sensitivity of 2.47 μA mM^?1 cm^? 2 for glucose at the composite film. The fabricated biosensor displayed two weeks stability. Moreover, it shows no response to 0.5 mM of ascorbic acid (AA), uric acid (UA), acetaminophen (AP), pyruvate (PA) and lactate (LA) which shows its potential application in the determination of glucose from human serum samples. The composite film exhibits excellent recovery for glucose in human serum at physiological pH with good practical applicability.     

Isothermal (vapour + liquid) equilibrium and thermophysical properties for (1-butyl-3-methylimidazolium iodide + 1-butanol) binary system

Experimental isothermal (vapour + liquid) equilibrium (VLE) data are reported for the binary mixture containing 1-butyl-3-methylimidazolium iodide ([bmim]I) + 1-butanol at three temperatures: (353.15, 363.15, and 373.15) K, in the range of 0 to 0.22 liquid mole fraction of [bmim]I. Additionally, refractive index measurements have been performed at three temperatures: (293.15, 298.15 and 308.15) K in the whole composition range. Densities, excess molar volumes, surface tensions and surface tension deviations of the binary mixture were predicted by Lorenz–Lorentz (n_D-ρ) mixing rule. Dielectric permittivities and their deviations were evaluated by known equations. (Vapour + liquid) equilibrium data were correlated with Wilson thermodynamic model while refractive index data with the 3-parameters Redlich–Kister equation by means of maximum likelihood method. For the VLE data, the real vapour phase behaviour by virial equation of state was considered. The studied mixture presents S-shaped abatement from the ideality. Refractive index deviations, surface tension deviations and dielectric permittivity deviations are positive, while excess molar volumes are negative at all temperatures and on whole composition range. The VLE data may be used in separation processes design, and the thermophysical properties as key parameters in specific applications.     

Measurements of methane hydrate equilibrium in systems inhibited with NaCl and methanol

Natural gas hydrates are ice-like inclusion compounds that form at high pressures and low temperatures in the presence of water and light hydrocarbons. Hydrate formation conditions are favorable in gas and oil pipelines, and their formation threatens gas and oil production. Thermodynamic hydrate inhibitors (THIs) are chemicals (e.g., methanol, monoethylene glycol) deployed in gas pipelines to depress the equilibrium temperature required for hydrate formation. This work presents a novel application of a stepwise differential scanning calorimeter (DSC) measurement to accurately determine the methane hydrate phase boundary in the presence of THIs. The scheme is first validated on a model (ice + salt water) system, and then generalized to measure hydrate equilibrium temperatures for pure systems and 0.035 mass fraction NaCl solutions diluted to 0, 0.05, 0.10, and 0.20 mass fraction methanol. The hydrate equilibrium temperatures are measured at methane pressures from (7.0 to 20.0) MPa. The measured equilibrium temperatures are compared to values computed by the predictive hydrate equilibrium tool CSMGem.     

Electrochemical kinetic study of surface layer growth on natural pyrite in acid medium

This paper presents electrochemical experiments on natural pyrite that combine potentiostatic and voltammetric techniques. X-ray microanalysis is used as an auxiliary technique. The layer growth on pyrite surface is conducted in a wide range of pH and potential range: 3.4 ≤ pH ≤ 5.9 with E = 0.80 V (versus SHE), and 0.80 V ≤ E ≤ 1.00 V with pH 4.5 (versus SHE) in acetic acid–acetate buffer. This work is unique for two reasons: (1) phenomenological model about layer growth is applied and mathematical-physic consistence is verified and (2) Meyer's hypotheses of chemical mechanism are used to explain kinetic parameters of the phenomenological model.     

Structure development during isothermal crystallisation of high-density polyethylene: Synchrotron small-angle X-ray scattering study

Isothermal melt crystallisation in high-density polyethylene (HDPE) was studied using the time-resolved SAXS method with synchrotron radiation over a wide range of crystallisation temperatures. The SAXS profile was analysed by an interface distribution function, g₁(r), which is a superposition of three contributions associated with the size distributions of crystalline (L_C) and amorphous (L_A) layers and a distribution of long period (LP). The morphological parameters extracted from the g₁(r) functions show that the lamellar thickness increases with time, obeying a logarithmic time dependence. The time evolution of L_C observed for the sample crystallised at 122 °C leads to the conclusion that crystallisation proceeds according to the mechanism of thickening growth. For samples crystallised at lower temperatures (116 °C and 118 °C), the lamellar thickening mechanism has been observed. The rate of lamellar thickening in these cases is much lower than that at 122 °C. At 40 °C, thickening of the crystalline layer does not occur. The interface distribution functions were deconvoluted, and the relative standard deviation σ_C/L_C obtained in this way is an additional parameter that is varied during crystallisation and can be used for analysis of this process. Time-dependent changes in the σ_C/L_C at large supercooling (T_C=40 °C) indicates that L_C presents a broad distribution in which the relative standard deviation increases with time. At lower supercooling (T_C=122 °C), L_C shows a much sharper distribution. In this case, the relative standard deviation decreases with time.     

(Solid + liquid) equilibria of (naphthalene + isomeric dichlorobenzenes)

(Solid + liquid) equilibria (SLE) have been measured for naphthalene + o-dichlorobenzene, + m-dichlorobenzene, and + p-dichlorobenzene using differential scanning calorimetry (DSC) over the whole concentration range. It was found that the phase diagram of (naphthalene + m-dichlorobenzene) is of a simple eutectic type with the eutectic point at 244.85 K and 0.058 mole fraction of naphthalene, the phase diagram of (naphthalene + p-dichlorobenzene) is of a simple eutectic type with the eutectic point at 302.85 K and 0.390 mole fraction of naphthalene and in the system of (naphthalene + o-dichlorobenzene), a 1:1 incongruently melting compound is formed and that the phase diagram show a eutectic and a peritectic, the eutectic point is at 232.55 K and 0.130 mole fraction of naphthalene, the peritectic point at 250.15 K and 0.077 mole fraction of naphthalene. Furthermore, the activity coefficients of components in mixtures of (naphthalene + m-dichlorobenzene) and (naphthalene + p-dichlorobenzene) have been correlated by the Scatchard–Hildebrand solubility parameter expression. This approach offers a useful procedure for estimating with good accuracy.     

Spontaneous formation of an electroactive co-polymeric film derived from nordihydroguaiaretic acid and 4,4′-diaminobibenzyl

Binary solution of nordihydroguaiaretic acid (NDGA) and 4,4′-diaminobibenzyl (DABB) undergoes rapid oxidation by ambient oxygen to form a thin film of poly-NDGA-co-DABB on the surface of the reaction chamber and on immersed substrates. Electrochemistry of thus formed films was studied in 0.1 M sulfuric acid and in phosphate buffer (pH 7.4). Electrochemical behavior of the co-polymeric film is characterized by two redox couples, the predominant one being observed at more negative potentials comparing to parent NDGA i.e. 0.28 vs. 0.49 V (vs. Ag/AgCl) in 0.5 M H₂SO₄. The peak potentials were shifted toward lower values with solution pH at the rate of 59 mV/pH unit indicating a 2e/2H⁺ transition as expected for quinone-containing films. The poly-NDGA-co-DABB film exhibits catalytic activity toward electroreduction of nitrite to nitric oxide in acidic electrolytes. This reaction can be used to quantify nitrite in a broad concentration range with low detection limit (0.3 μM, S/N = 3).