锐钛矿(TiO2)半导体的氧空位浓度对导电性能影响的第一性原理计算

基于低温重氧空位锐钛矿半导体的态密度计算，在同等条件下研究取不同大小模型的锐钛矿做适量浓度的氧空位存在，分别对进入导带的相对平均电子数和氧空位类杂质的散射迁移率进行计算，之后对电导率进行类比，发现锐钛矿半导体的导电性能对适量浓度低的氧空位有利可行得到了证明.同时，低温重氧空位的条件下，锐钛矿半导体的电导率不仅与氧空位浓度有关，而且和进入导带的平均电子数有关，和氧空位散射的电子迁移率有关的正确结论.     

锐钛矿(TiO2)半导体的氧空位浓度对导电性能影响的第一性原理计算

基于低温重氧空位锐钛矿半导体的态密度计算,在同等条件下研究取不同大小模型的锐钛矿做适量浓度的氧空位存在,分别对进入导带的相对平均电子数和氧空位类杂质的散射迁移率进行计算,之后对电导率进行类比,发现锐钛矿半导体的导电性能对适量浓度低的氧空位有利可行得到了证明.同时,低温重氧空位的条件下,锐钛矿半导体的电导率不仅与氧空位浓度有关,而且和进入导带的平均电子数有关,和氧空位散射的电子迁移率有关的正确结论. 关键词： 锐钛矿半导体 氧空位浓度 电导率 第一性原理计算     

氧空位浓度对ZnO电子结构和吸收光谱影响的研究

目前,氧空位对ZnO形成杂质能级的研究结果存在相反的结论,深杂质能级和浅杂质能级两种实验结果均有文献报道,并且,在实验中高温加热的条件下,氧空位体系ZnO中导带自由电子增加的来源认识不足.为了解决此问题,本文采用密度泛函理论框架下的第一性原理平面波超软赝势方法,建立了纯的与两种不同氧空位浓度ZnO超胞模型,分别对模型进行了几何结构优化、态密度分布、能带分布、布居值和差分电荷密度的计算.结果表明,氧空位浓度越大,系统能量越上升、稳定性越下降、形成能越高、氧空位越难、导带越向低能方向移动、电子跃迁宽度越减小、吸收光谱越红移.这对设计制备新型氧空位ZnO体系光学器件有一定的理论指导作用.     

Computer simulation of intrinsic defects in YAlO3 single crystal

Computer simulation techniques were used to investigate intrinsic defects in YAlO₃ single crystal. A set of short-range potential parameters were derived using a relaxed fitting procedure incorporating with the known crystal properties. These parameters were then applied within the framework of the shell model. The simulation results reveal that oxygen Frenkel disorder and the antisite defect of Al ion substituting the Y ion dominate the intrinsic defects in YAlO₃. An analysis of redox reactions corroborate that the oxidation is most likely to occur via forming interstitial oxygen, while the oxidation via filling oxygen vacancies and reduction reaction may predominate at high temperature. The activation energy of oxygen vacancy migration on conduction was also studied.     

Ce和O空位共掺杂TiO_2的电子结构与光学性质

采用基于密度泛函理论加U的计算方法,研究了Ce和O空位单(共)掺杂锐钛矿相TiO_2的电子结构和光吸收性质.计算结果表明,Ce和O空位共掺杂TiO_2的带隙中出现了杂质能级,且带隙窄化为2.67 eV,明显比纯TiO_2和Ce,O空位单掺杂TiO_2的要小,因而可提高TiO_2对可见光的响应能力,使TiO_2的光吸收范围增加.光吸收谱显示,掺杂后TiO_2的光吸收边发生了显著红移;在400.0—677.1 nm的可见光区,共掺杂体系的光吸收强度显著高于纯TiO_2和Ce单掺杂TiO_2,而略低于O空位单掺杂TiO_2.此外,Ce掺杂TiO_2中引入O空位后,TiO_2的导带边从-0.27 eV变化为-0.32 eV,这表明TiO_2的导带边的还原能力得到了加强.计算结果为Ce和O空位共掺杂TiO_2在可见光光解水方面的进一步研究提供了有力的理论依据.     

Mg掺杂PST薄膜的溶胶-凝胶法制备及晶相形成研究

利用溶胶-凝胶法成功制备了Mg掺杂Pb_0.4Sr_0.6Mg_xTi< sub>1-xO_3-x薄膜，利用x射线衍射仪对薄膜的物相和结构进行了分析， 用扫描电子显微镜对薄膜的形貌和断面等进行了观察.研究结果表明，薄膜以立方钙钛矿为 晶相，薄膜中晶相以团聚状颗粒存在，晶相含量受热处理条件和Mg的掺杂量所控制.Mg掺杂 对Pb_0.4Sr_0.6Mg_xTi_1-xO_3-x 薄膜晶相含量的影响与钙钛矿中的氧空位缺陷相关.在一定的掺杂范围内，由掺杂引起晶相 的晶格畸变较小时，体系掺Mg平衡了晶体内本征氧空位引入的电荷不平衡，使晶相更为稳定 ，析晶能力提高，晶体形成量随掺杂浓度的提高而提高.当掺杂浓度达到一定量时， 随着Mg 掺杂浓度增加，一方面使形成晶体时杂质浓度增加造成参与形成晶相的组成含量下降，另一 方面使进入钙钛矿结构的Mg增加，氧空位大量增加使畸变程度提高，形成的晶相不稳定，析 晶能力下降，晶体含量随掺杂Mg浓度的增加而不增反降.在相同条件下制备的Pb_{0.4Sr0.6MgxTi1-xO3-x薄膜中Mg掺量约为 x=0.01时，得到的钙钛矿相含量最高，本征氧缺陷所带入的正电荷和Mg引入时带入的负电荷 间达到平衡.此外，Mg的掺入还影响到析晶与热处理过程之间的关系.在高Mg掺量范围，Mg含 量越高，形成的晶相越不稳定，热处理时间越长，使热处理过程中分解的晶相量越多，随Mg 掺量越高和热处理时间越长，薄膜中晶相含量越低. 关键词： 溶胶-凝胶法 PST薄膜 Mg掺杂 晶相形成}     

Oxygen vacancy pairs on CeO2(110): A DFT + U study

Oxygen vacancy pairs have been suggested to play a role in the reduction of NO molecules on ceria and for the oxidation processes of reducible rare-earth oxides. The formation energy of the oxygen vacancy pairs and the changes in the structural and electronic properties of the ceria (110) surface with oxygen vacancy pairs are investigated using density-functional theory (DFT + U) methodology within the generalized gradient approximation. It is found that the excess electrons localize on the Ce ions neighbouring the vacancies, and the most stable structure for the oxygen vacancy pairs on the ceria (110) surface is at next-nearest-neighbour site.     

Oxygen vacancy clustering and electron localization in oxygen-deficient SrTiO(3): LDA + U study

We find, using a local density approximation +Hubbard U method, that oxygen vacancies tend to cluster in a linear way in SrTiO(3), a prototypical perovskite oxide, accompanied by strong electron localization at the 3d state of the nearby Ti transition metal ion. The vacancy clustering and the associated electron localization lead to a profound impact on materials properties, e.g., the reduction in free-carrier densities, the appearance of characteristic optical spectra, and the decrease in vacancy mobility. The high stability against the vacancy migration also suggests the physical reality of the vacancy cluster.     

Electronic energy structure of vacancy and divacancy in SiO2

We investigated electronic energy structure of vacancy and divacancy in SiO₂, and found that oxygen vacancy and divacancy give rise to bound-states near the edge of the conduction band, whereas localized states related to the silicon vacancy occur in the valence band. Our results demonstrate that the doubly occupied oxygen vacancy state yields electrons to silicon in Si-SiO₂ junction and serves as a fixed oxide charge.     

Ordering of oxygen vacancies in a CaMnO<Subscript>3 − δ</Subscript> perovskite single crystal

The structure of a CaMnO_{3 ? δ} perovskite single crystal was studied for the first time using thermal neutron diffraction in the temperature range 300–840 K. It was detected that oxygen vacancies in the crystal are ordered into two types of superstructure. A phase with a relative number of vacancies δ = 1/4 occupies the largest volume fraction of oxide (～75%); the other volume is occupied by a superstructure with a lower vacancy content (δ = 1/5). The oxygen deficiency in the crystal lattice was determined to be δ = 0.238. The mechanism of oxygen vacancy ordering in the oxide is discussed taking into account its charge state.     

Frequency–temperature response of CaBi4Ti4O15 ceramic prepared by soft chemical route: Impedance and modulus spectroscopy characterization

Polycrystalline CaBi₄Ti₄O₁₅ ceramic has been prepared through a modified chemical reaction technique. Room temperature X-ray diffraction (XRD) analysis shows the formation of a single phase orthorhombic perovskite structure. Simultaneous analysis of the complex impedance (Z1), and electric modulus (M1) spectroscopy was carried in the temperature range of 100–850 °C. The dielectric relaxation is found to be of non-Debye type. The Nyquist plot shows the negative temperature coefficient of resistance type behavior. Two different conduction mechanisms are may be due to: (a) the dielectric relaxation processes due to localized conduction associated with oxygen vacancy; and (b) the non-localized conduction corresponding to long range conductivity associated with extrinsic mechanisms fundamentally associated due to the chemical inhomogeneity caused due to the difference in the ionic environment of Ca²⁺ and Bi³⁺ and their sharing in the A site of perovskite and [Bi₂O₂]²⁺ slabs. Different conductivity components are recognized inside the grain: long range dc conductivity at low frequency region, a capacitive behavior at higher frequencies, and a universal power law behavior in an intermediate-frequency region where grain boundary contributions are neglected.     

First-principles study of photoconductivity in BaTiO3 with oxygen vacancies

The photoconductivity of BaTiO_2.5 with oxygen vacancy has been studied by the linear muffin-tin orbital method in the atomic sphere approximation (LMTO-ASA). The ground-state structure of BaTiO_2.5 is obtained by minimization of the total energy. The partial densities of states show that the occupied states at the bottom of the conduction band have primarily Ti d orbital character. The photoconductivity shows that two novel features, in the low energy side, can be attributed to the intraband transition of free electronic carriers in the vicinity of the Fermi level and the interband transition of the Ti 3d(yz) related band states, to the Ti 3d(xy,xz) related band states, respectively. In addition, it is also found that the anisotropy of photoconductivity is enhanced because of the introduction of oxygen vacancy. The system can show the conductive behavior of electronic carriers, which is qualitatively in agreement with a recent experimental finding.     

First-Principles Study of Electronic Properties in PbS（1^-00） with Vacancy Defect

Electronic properties of both Pb and S vacancy defects in PbS（1^-00） have been studied using the first-principles density functional theory （DFT） calculations with the plane-wave pseudopotentials. It is found that the density of states （DOS） near the top of the valence band and the bottom of the conduction band is significantly modified by these defects. Our calculation indicates that in the case of S vacancy defects the Fermi energy shifts to the conduction band making it as an n-type PbS （donor）. However, in the case of Pb vacancy, because of the appreciable change of the DOS, the system acts as a p-type PbS （accepter）. In addition, the structural relaxation shows that the defect leads to outward relaxation of the nearest-neighbouring atoms and inward relaxation of the next-nearest neighbouring atoms.     

Simultaneous doping with La and Y for Ba- and Ce-sites in BaCeO3 and the ionic conduction

Powder X-ray diffraction (XRD) analysis showed that the single phase perovskite-type structure of Ba_1−xLa_xCe_0.90−xY_0.10+xO₃₋ (0 x 0.40, =0.05) could be maintained in a wide region of doping level by simultaneous partial substitution of La³⁺ for Ba²⁺-site and Y³⁺ for Ce⁴⁺-site in BaCeO₃. The conduction properties of these oxides were investigated using various electrochemical methods in the same concentration of oxygen vacancy (=0.05). At high oxygen partial pressure, these oxides exhibited a mixed oxide ionic and p-type electronic conduction while at low oxygen partial pressure their conduction was almost protonic. Among these oxides, BaCe_0.90Y_0.10O₃₋ exhibited the highest conductivities with a value of 1.24×10⁻¹ S/cm in dry oxygen, and 5.65×10⁻² S/cm in wet hydrogen at 1000°C. Both of the proton and oxide ion conductivities under oxygen and under hydrogen atmospheres decreased monotonically with the increasing substitution for Ba²⁺- and Ce⁴⁺-sites. The decreases in ion conductivities appear to relate to the decreased free volume (V_f) of crystal lattice as well as the increased distortion of lattice from ideal cubic perovskite structure.     

Effects of disorder on tunnel magnetoresistance in Fe/MgO/Fe junctions

Effects of lattice distortion and oxygen vacancy on tunnel magnetoresistance in Fe/MgO/Fe junctions are theoretically investigated. By treating the distortion in MgO as the random potential and performing numerical simulations based on the Kubo–Landauer formula, it is shown that the magnetoresistance ratio decreases with increasing randomness. Moreover, first-principles calculations within the density functional theory show that the defect states in the Fe/MgO cluster containing an oxygen vacancy induce no significant shift in the Fermi level.     

Diffusion of hydrogen and oxygen in the high temperature proton conductor srceo3 investigated by dynamic conductivity measurements

In SrCeO₃ the oxygen vacancy concentration at elevated temperatures depends on the oxygen partial pressure in the surrounding atmosphere. Changes of the oxygen vacancy concentration are accompanied by change in the hole concentration and therefore can be measured by electrical conductivity measurements. We apply a dynamic method for studying the diffusion of oxygen vacancies by measurements of the time dependence of the electrical conduction after a sudden change in the oxygen partial pressure has taken place.

In doped samples and under wet conditions the protonic charge carriers are mainly incorporated by a dissociative absorption of water and lead to a noticeable protonic conduction. The proton diffusion in SrCe_0.95 Y_0.05O₃ is determined by relaxation measurements at a polarised sample in wet and hydrogen containing atmosphere. The electrochemical cell discussed here is characterised by a combination of one reversible and one (hydrogen) ion blocking electrode. From the time dependence of the depolarisation process the hydrogen diffusivity is extracted.     

Microstructures and impedance studies of Bi<Subscript>3.15</Subscript>Nd<Subscript>0.85</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films

Microstructures and impedance characteristics of chemical-solution-derived Bi_3.15Nd_0.85Ti₃O₁₂ thin films were studied as functions of temperature. A dielectric anomaly was found at around 450°C, corresponding to the paraelectric to ferroelectric transition. Via complex impedance studies, grain and grain boundary contributions to the impedance were separated. The resistance of grain and grain boundaries is found governed by the same kind of space charge with an activation energy around 1.1 eV, close to that of oxygen vacancies in perovskite ferroelectrics. The low temperature ac conductance of BNdT thin films shows a frequency dispersion, which can also be ascribed to space charges mainly due to oxygen vacancies. The results were compared with SrBi₂Ta₂O₉ in terms of oxygen vacancy conductivity.     

A first-principles study of the effect of oxygen vacancy on rutile Ti1−xCdxO2

A first-principles study has been performed to understand the effect of oxygen vacancy on the electronic properties of cadmium doped rutile TiO₂. We observe that Cd incorporation on rutile TiO₂ induces Cd p-states on the top of the valence band which is consistent with an earlier result of Zhang et al. (2008) [5]. Furthermore, by creating an oxygen vacancy, some new states are induced, which originate from the Ti 3d electrons at the middle of the band gap and spread up to the conduction band. Therefore, the band gap of the material reduces significantly, making it suitable to act as a better photocatalyst.     

氧空位对共掺型锐钛矿TiO2能带结构的影响

基于电子密度泛函理论计算,系统研究了氧空位对V-C(p型)、Cr-N(n型)、V-N和Cr-C(电中性)四种共掺型锐钛矿TiO₂的几何和电子结构的影响．结果表明在最稳定构型中氧空位处在与金属杂质原子相连的位置．由于氧空位的出现,共掺TiO₂禁带中一些未占据的杂质态被填充满电子,掺杂体系的导带带边位置几乎不变,这有利于减少光生载流子复合,且不影响光解水过程中的产氢反应,在厌氧条件下很容易在V-N共掺TiO₂中引入氧空位．     

多铁性钙钛矿薄膜的氧空位调控研究进展

精确调控ABO_3钙钛矿结构中氧空位的位置与浓度已被证明可调控多铁性薄膜的不同物理性质,包括输运特性、光学特性和多铁性质等.本文回顾了多种典型的多铁性材料,从氧空位形成机理、氧八面体结构、应变-氧空位关系和具体物性调控效应(多铁、超导和电化学性能)等角度介绍了该体系中氧空位调控效应.同时依托氧空位调控的最新研究进展,尤其是对氧空位调控单相材料多铁性质方面工作的分析,为探索新型磁电功能性材料与器件提供了重要参考.